Search Documents

The treatment of gold-plant tailings with ferrous sulphate to remove the cyanide is currently in use, on several gold plants. In some cases there is scope for optimization the process. The present work provides a detailed study of the reaction between cyanide and ferrous sulphate. Optimal conditions for the removal of total cyande required a ph of 5,.5 to 6,5 and an Fe:CN molar ratio of 0,5. Ferrocyanide ion is shown to be unstable In aqueous acidic solution, with rapid oxidation to ferricyanide, (Fe(CN) 6 ), and formation .of Fe(CN)5H2O3- at pH values below 4, The precipitate from the reaction between cyanide and ferrous sulphate consists mainly 01 Insoluble Prussian blue, Fe4[Fe(CNI&!.3,and IS shown to be unstable in the presence of alkaline solution, since it decomposes rapidly at pH values above 7 to form ferrocyanide, (Fe(CN)6 ), in solution and various insoluble iron oxides,

Jan 1, 1992

By L. A. Cornish, I. A. Mwamba, R. A. Couperthwaite

"In previous work by the authors, it was established that additions of 0.2 at.% Ru to an Fe-40 at.% Al alloy improved the corrosion and oxidation resistance of the alloy. The alloy was produced by mechanical alloying and spark plasma sintering and the work showed that nonequilibrium processing was able to significantly refine the grain size of the material. The sintered material had a higher hardness than the as-cast material and the change in grain size did not significantly affect the oxidation and corrosion. In the present research, the mechanically alloyed powder was coated onto a mild steel substrate using cold-spray coating at a gas pressure of 10 bar and a temperature of 500°C. The coatings were found to be 5–10 um thick, although thicknesses of up to 30 um were observed. The coated materials were subjected to oxidation and corrosion tests to determine the effectiveness of the coating in increasing the oxidation and corrosion resistance of mild steel. This was done to determine the effectiveness of cold-spray coating as a technique to coat these mechanically alloyed powders. IntroductionPrevious work conducted by Mintek (Couperthwaite et al., 2013, 2015) investigated the effect of precious metal additions on the structure, oxidation and corrosion properties of an Fe-40 at.% Al (Fe- Al) alloy. Initial work determined that additions of more than 0.5 at.% precious metal did not improve the oxidation and corrosion properties of the materials and in some cases even decreased the resistance to corrosion. Further work identified Pt and Ru as beneficial additions to the FeAl alloy. Four alloys were then produced by mechanical alloying and sintering (FeAl–0.2 at.% Pd, FeAl–0.2 at.% Ru, FeAl–0.5 at.% Ag, FeAl–0.5 at.% Pt). These alloys were all successfully produced by melting and casting and mechanical alloying sintering and it was found that the nonequilibrium processing greatly decreased the grain size of the materials compared to the ascast materials. It was found that the additions of Ru and Pt were still the most beneficial to the oxidation and corrosion properties, with Ru being considered the most beneficial."

Jan 1, 2016

By B. Rezai, Z. Pourkarimi, M. Noaparast, S. Chehreh Chelgani

Nanobubbles (NBs) flotation separation can be an indicator for improving the efficiency of fine particles through the conventional process. Since flotation reagents such as frothers can reduce bubble size, they can potentially be used for the generation of NBs and develop a selective NB flotation separation. This study explored the flotation separation of fine phosphate particles from their associated minerals in the presence of NBs, which were generated by using a phosphate flotation reagent (Flo-YS: collector-frother). The results of flotation tests showed that in the presence of NBs, the flotation efficiency was significantly improved. However, in the presence of NBs, surface chemistry analyses (Fourier Transform Infrared Spectroscopy and High-Performance Liquid Chromatography) illustrated that the collector adsorption on the surface of phosphate particles decreased. A comparison between outcomes of various phosphate flotation conditions indicated that increasing the flotation efficiency in the presence of NBs may be due to the aggregation of fine particles by the generated NBs, and also selective adsorption of NBs (hydrophobisation) on the surface of particles. In other words, generating NBs by selective collectors may increase efficiency and decrease the collector consumption of a flotation process. Keywords: Phosphate, selective separation, fine particles, collector-frother, efficiency, mechanical flotation cell

Jan 1, 2020

By W. Soetaert, P. Dhar, H. R. Kota, M. Thornhill, S. Roelants, I. V. Chernyshova

Yeast-derived bola-amphiphiles have attracted considerable attention for their applications in various industrial sectors in recent years. However, only a few studies on this class of surfactant were reported to be relevant to mineral processing applications. In this paper, one of the novel surfactants, acidic glucolipid obtained from Candida bombicola sophorolipids and modified by using Penicillium decumbens naringinase substrate has been evaluated for its interaction with chalcocite and calcite minerals because of a new Cu-ore Nussir deposit in Norway containing calcite impurity. The interaction of glucolipid biosurfactant with copper sulphide and carbonate minerals was investigated with zeta potential, adsorption and FTIR studies, and also by Hallimond tube and bench scale flotation tests using pure minerals and Nussir copper ore, respectively. The results illustrate collector adsorption and flotation of copper sulfides at neutral pH. The bench-scale flotation results demonstrate that copper sulphides can be selectively floated from carbonate and silicate gangue minerals. This study underlines the glycolipid’s high potential for its use as collector for flotation of valuable copper sulphide minerals. Keywords: Flotation, biosurfactants, adsorption

Jan 1, 2020

By D. van Rensburg

Jointed rock slopes are generally stable, as there is no freedom of movement for blocks of rock. In an open- pit mining environment, blasting opens up space into which blocks of rock can fail, resulting in the common occurrence of slope failure. Prior to the blasting of a trim pattern, the immediate highwall is scaled, where loose rock material is removed by means of a mechanical scaler. As mining of the pit progresses, the height of the scaled highwall from the pit floor progressively increases. These highwalls are never scaled again for the remainder of the pit life, and time-dependant deterioration contributes to these highwalls becoming subject to rockfall and, sometimes, slope failure. This paper documents the development of a South African innovation, a remote-controlled mechanical highwall scaler, a world first for the mining industry. The scaler will enable open-pit highwalls to be scaled from crest to toe whenever the need arises. It will reduce the risk associated with highwalls and deliver on the Anglo American promise of producing safe, profitable platinum.

Jan 1, 2012

By S. Krishnannair

Singular Spectrum Analysis (SSA) is an effective data-adaptive multimodal tool for monitoring chemical processes. However, monitoring multiscale signals using principal component analysis obtained from the multilevel decomposition of process signals using basic SSA assume the upper control limits of monitoring charts (" ) to have a Gaussian distribution. This assumption deteriorates the performance of basic SSA when applied to the monitoring of nonlinear processes. To address the issue in this paper, the kernel density estimation (KDE) was used to estimate upper control limits of monitoring charts for basic SSA based nonlinear process monitoring techniques. The monitoring performance of the resulting basic SSA-KDE approach was then compared with a basic SSA approach of which upper control limits of the monitoring charts were determined based on a Gaussian distribution. Application on nonlinear dynamic simulated process and base metal flotation plant chemical processes showed that the SSA-KDE approach provided better overall performance than the SSA approach with Gaussian assumption-based upper control limits for its monitoring charts. Keywords: Fault detection, singular value decomposition, singular spectrum analysis, kernel density estimation

Jan 1, 2020

By M. L. Mahlatji

Mechanical alloying of an equiatomic mixture of crystalline Ti and Pt elemental powders in a high-energy ball mill formed an amorphous alloy by solid-state reactions. Mechanical alloying was carried out in an argon atmosphere at a rotation speed of 1200 r/min and a 20:1 ball-to-powder weight ratio, for time intervals of 4 to 40 hours. At an intermediate stage of mechanical alloying, scanning electron microscopy showed the formation of characteristic layered structures of inhomogeneous composition within the powder particles. X-ray diffraction analysis showed the gradual disappearance of crystalline Bragg peaks and the emergence of broad amorphous maxima as milling progressed. The amorphization process was completed after 8?12 hours. The amorphous state of the product indicated that temperatures during processing did not exceed the crystallization temperature of the alloy.

Jan 1, 2014

By M. Pierce, E. Karampinos

"One of the main challenges in the numerical modelling of ground support in underground excavations is to reproduce the performance of the sequential installation of the reinforcement while capturing the rock mass behaviour of an advancing face in 3D. The 3D modelling approaches used to simulate the progressive advance of excavations are mostly continuum and often cannot reproduce the rock mass failure mechanisms. The 3D discrete element method (DEM) can better reproduce structurally controlled rock mass failure mechanisms and can explicitly represent the reinforcement elements. This paper builds on previous work that reproduced the structurally controlled squeezing conditions in an underground hard-rock mine using 3D DEM and the in situ behaviour of reinforcement under pull conditions. It addresses important issues on the way reinforcement is explicitly introduced in discrete element models. A pseudo-3D model is employed to overcome the computational restrictions and time limitations of a 3D modelling approach. The work focuses on the scaling of the material properties of the ground support elements when the thickness of the model is not equal to the out-of-plane spacing of reinforcement. It demonstrates the scaling methodology based on the type of the modelled reinforcement elements used and investigates the significance of this approach. The advantages and disadvantages of this approach with respect to 2D and 3D methods are discussed. The results are compared with field data and previous modelling work done at the mine. IntroductionNumerical models can provide significant insight into the anticipated behaviour of underground excavations. The modelling of ground support, however, is not a trivial exercise. An effective representation of ground support in underground excavations should capture the behaviour of both the rock mass and the support elements. When numerical models are used for design purposes, the complexity of the problem requires significant time and expertise (Sweby, Dight, and Potvin, 2016).At a laboratory scale, numerical models have successfully reproduced the results of laboratory tests on rockbolts by explicit modelling of the bolt, the borehole, and the grout. Chen and Li (2015) used a continuum FLAC3D (Itasca Consulting Group Inc., 2012) model to simulate the mechanical behaviour of D-bolts as observed experimentally. Grasselli (2005) used a 3D finite element code to model the behaviour of fully grouted rods and expandable bolts under shear."

Dec 1, 2018

By J. N. Baloyi

"In atomic emission and atomic absorption spectrophotometry, the sample is heated to a high temperature and thereby decomposed into atoms and ions that absorb or emit visible or ultraviolet electromagnetic radiation at energies characteristic of the elements involved. The flame test is a very simple form of this technique. The yellowing of a flame by the addition of salt, for example, occurs because the sodium in salt emits strongly in the yellow portion of the visible spectrum. These methods are especially useful for low concentrations of metallic elements in both qualitative and quantitative analysis.Interference on Iep-OES has not always been considered a serious problem, especially in the beginning, when compared with Atomic Absorption Spectroscopy. This was due to the euphoria created by the new technique. It meant that criticism was subdued. The Iep was vastly superior to the Atomic Absorption technique, that the interferences suffered by the Atomic Absorption technique dwarfed the little interferences suffered by the rep-OES technique. This is how rep-OES has had a reputation as an interference free technique."

Jan 1, 2014

By Z. Halifa, P. G. Geyer

Tapping a blast furnace is necessary not only to deliver the product, but is also essential for the safety of the furnace and workers in the cast-house. This paper will highlight the practices at ArcelorMittal’s blast furnaces in the Vanderbijlpark Works, with specific focus on tap-hole design and monitoring as well as casting practice. Extension of the tap-hole life and hearth campaign will be illustrated with reference to the methods of maintenance of the tap-holes, troughs, runners, and cast-house equipment. The importance of proper cooling, good thermocouple installation, and temperature monitoring will be explained.

Jan 1, 2014

By K. M. Primrose

Electrical tomography has developed rapidly over the last few years in its sophistication and practical use to enable three-dimensional information on the distribution of phases within flowing mixtures to be observed1. This paper reviews the current state of application from the industrial perspective, drawing on applications case studies based on scaling studies in the laboratory right through to installations on plant. In the laboratory, applications have looked at scale-up of mixing2 processes involving gas-liquid and solid-liquid suspensions3 with a particular interest in verifying computational fluid dynamics simulations or in checking scale-up design4,5. In the processing plant, the circumstances are usually bespoke and may range from simple detection of the degree of homogeneity of a flowing mixture through to the need to measurement a sophisticated batch process such as crystallization, sedimentation, filtering and drying. Examples drawn from the chemical and pharmaceutical industries will be presented and related to the benefits that can be gained through application of the method.

Jan 1, 2008

By A. Dabbagh

The aim of this research was to investigate the effect of coke particle size on the thermal profile of the charge bed in the sintering process of iron ore. Six different ranges of coke particle size that could be used in practice in the sintering line of Esfahan Steel Company (ESCO) were used while parameters such as ratios and particle sizes of other ingredients, ignition temperature, and suction power were kept constant. Thermal profiles were obtained by measuring the temperature changes at three points in the sintering bed. The influence of coke particle size on rate of temperature rise, maximum temperature of the sintering bed, and the flame front velocity of the sintering bed was determined by analysing the thermal profiles. Moreover, the cold strengths of the sinters were measured using the Tumbler method. The results indicated that the coke particle size has a significant impact on the thermal properties of the sintering bed. Based on the results, a coke particle size between 0.212 mm and 3.350 mm was determined as the optimal range for the specific conditions in the sintering line of ESCO. Keywords iron ore sintering, coke particle size, thermal profile, flame front velocity, Tumbler index.

Dec 1, 2013

By Mike Stanley

This is a case study of an opencast coal mining operation where the physical and financial performance was improved via applying a process of transformational leadership development. [ ]

Jan 1, 2008

By S. V. Mkhatshwa

The purpose of the study was to investigate the factors which affect the performance of the loading and hauling fleet and also find possible solutions to eliminate these factors, so that the daily tonnages required could be produced .This is due to the high demand of manganese required by clients. The investigation strongly focuses on the performances of the three 777D Caterpillar trucks and the R984 C Liebherr Litronic Hydraulic Excavator. In the content of the study, these machines are used to remove and move the low grade manganese (also known as the top cut overburden) in order to expose the high grade manganese from north pit to dump 4. The objectives of the project were to determine the actual performance of the loading and hauling fleet per shift, compare the actual and the theoretical performance and identify areas that need to be improved. To achieve the goals set for the project, a number of activities were carried out. ?Perform a time study to compare the performance of the loading and hauling fleet with the manufacturer specifications ?Match the equipments analysis for Loading and hauling ?Road conditions analysis ?Rolling resistance and Road Gradients analysis ?Operating cost analysis.

Jan 1, 2009

By J. Bai, C. Zang, W. Yuan, L. Zhuang

"This study evaluates the efficiency of using mechanochemical reduction to assist the extraction of zinc from zinc ferrites by alkaline leaching. The transition of zinc ferrite into a metastable state after mechanochemical reduction with metallic iron contributes to the ready dissolution of zinc from the activated zinc ferrites in alkaline solution. Zinc ferrites were mechanochemically reduced under conditions of Fe:ZnFe2O4 mole ratio of 2:1, using 5 mm diameter stainless steel balls as the activation medium at a mass ratio of balls to raw materials of 25:1. Subsequent leaching in 6 mol/L NaOH solution at 90°C resulted in more than 70% Zn extraction. These results may be used to further develop a hydrometallurgical process for recovering zinc from zinc ferrites in alkaline solution.IntroductionZinc is an important nonferrous metal required for various applications in batteries, solder, dielectric materials, and piezoelectric materials. High-grade, easily concentrated ores are becoming scarcer: to meet world demands for zinc, it is necessary to develop economical and environmentally safe metallurgical technologies that use secondary materials such as leach residues of roasted zinc concentrates and electric arc furnace dusts. The zinc in the majority of these wastes occurs in the form of zinc ferrite (franklinite, ZnFe2O4), which is very stable and insoluble in most acidic and alkaline solutions (Langova and Matysek, 2009; Youcai and Stanforth, 2000).Several pyrometallurgical and hydrometallurgical processes (Jankovi et al., 2014; Langova and Matysek, 2010; Morcali et al., 2012; Shawabkeh, 2010) have been proposed for the treatment of zinc ferrites. Pyrometallurgical methods are costly owing to high energy consumption and their emissions of toxic gases are considered an environmental problem; hydrometallurgical methods are preferred for process economy and environmental reasons (Copur et al., 2004)."

Jan 1, 2016

By Yuandong Qiao, Erdong Li, Chao Lv, Junjian Ye

The gas-based CO reduction of Panzhihua vanadium titanomagnetite concentrate from 1100°C- 1250°C was investigated in this paper. The reduction degree increased with increasing temperature and increasing reduction time. At a temperature of 1250°C and a reduction time of 20 minutes, the metallisation degree reached 92%. The iron-titanium oxide phase transformation during reduction process was Fe2.75Ti0.25O5→Fe2.5Ti0.5O4→FeTiO3→FeTi2O5 according to the X-ray diffraction analysis. The SEM and map scan by energy spectrum of results of reduced samples at different temperatures indicated that the metallic iron particle size increased gradually as the reduction temperature increased. These results can serve as a reference for the reduction of vanadium titanomagnetite by CO. Keywords: Vanadium titanomagnetite concentrate, CO reduction, phase transformation, reaction mechanism

Jan 1, 2020

By T. G. Pedro, Q. Gonzalo, R. E. Roberto

Anionic surfactants, such as oleic acid and sodium oleate (OLE), and cationic surfactants, such as dodecyl amine-hydrochloride (DDA), are used as flotation collectors of spodumene. However, recovery is poor even if activating ions are used because gangue minerals are also activated. Some reports demonstrate that OLE/DDA mixtures act as a selective collector to enhance spodumene recovery. From mostly macroscopic tests, it has been argued that anionic OLE and cationic DDA form electroneutral complexes, which are adsorbed on the mineral surface through chemisorption; however, no molecular evidence has been presented. Therefore, the adsorption mechanisms of the collector mixtures remain mostly unknown. It seems necessary to first study the behaviour of these surfactants confined in salt solutions, to determine auto-associations when they are pure and cross-associations when mixed, the transition from monomers to micelles, and the structure of the micelles and the effects of pH, temperature and concentration. In this paper, ab initio calculations are first used to determine the surface charge distribution of OLE and DDA separately. Then molecular dynamics simulations are used to determine the conformation, aggregation, and diffusion of these pure and mixed surfactants in freshwater and saltwater with the ionic strength of seawater in a pH range. In particular, it is interesting to determine the various associations that result in mixtures of both surfactants and the impact of alkali and alkaline earth metal cations on the structures formedp. Cations influence the order of the structure and orientation of water dipoles, reducing the mobility of water, ions, and surfactant molecules. This knowledge is critical to improve the molecular understanding of the adsorption mechanisms on minerals. Keywords: Computer simulation, molecular dynamics, flotation, collectors, saltwater

Jan 1, 2020

By G. Akdogan, S. M. Bradshaw, A. P. Van Wyk, T. Punt

Recycling has become an important part of the lithium-ion battery (LIB) life cycle due to the growing demand for energy storage in applications like electric vehicles and renewable energy. Recycling spent LIBs provides a secondary source for strategically scarce metals, like lithium and cobalt, helping to reduce the environmental impact of LIBs. Organic acids have been proven to be effective lixiviants with the benefit of reduced environmental impacts, amongst which citric acid has shown to exhibit similar extraction performance when compared to mineral acids. Leaching LCO and NMC batteries with 1.5M citric acid and 2 vol.% H2O2 at 95°C, 20 g/L for 20 minutes achieved 93% Al, 90% Co, 96% Li, 94% Mn and 94% Ni dissolution. The strong chelating property of citric acid affects the separation of the metals, providing unique extraction opportunities. The first extraction uses 12 vol.% D2EHPA at a pH of 2.5 and O/A ratio of 2 to separate 96.4% Mn and 100% Al from the PLS in two counter-current stages. Stripping the loaded organic with 1.25M citric acid at an A/O ratio of 3 allows for up to 91% stripping of the manganese in a single stage. The second extraction then separates 96.5% Li from the PLS in three counter-current stages using 20 vol.% D2EHPA at a pH 5.5 and O/A ratio of 5. The raffinate remaining after the second separation contains 48.4 wt.% Co and 50.3 wt.% Ni. Keywords: Hydrometallurgy, lithium-ion batteries, metal recycling, citric acid, solvent extraction

Jan 1, 2020

By B. Nemutudi, X. Zhang, B. McFadzean, P. E. Ngoepe, P. P. Mkhonto, S. Pikinini

The comparison study on adsorption of potassium normal butyl xanthate (PNBX) and sodium (nbutyl) dithiocarbamate (SNBDTC) on sperrylite mineral forms a basis in understanding the floatability improvement and paves a way for the design of collectors that may impact on a wide range of arsenide minerals. This study used a computational density functional theory (DFT) and experimental microcalorimetry approach to determine the adsorption energies of PNBX and SNBDTC collectors onto a sperrylite mineral surface. From a computational aspect, we considered the most stable surface plane of (100) surface, which had been found to give the lowest surface energy, compared to the other surface planes. It was observed that the PNBX and SNBDTC preferred to bridge on the As and Pt atoms through the S atoms. These findings showed that the collector adsorbed on the surface through both Pt and As atoms and indicated that the As atoms were significantly active in the adsorptions. We found that the adsorption energies were in the order: SNBDTC (–278.38 kJ/mol) > PNBX (–270.92 kJ/mol), indicating that the dithiocarbamate had stronger exothermic adsorption than the xanthate. From the microcalorimetry test it was also found that the SNBDTC was more exothermic than the PNBX and the adsorption energies were: SNBDTC (–473.50 kJ/mol) > PNBX (–331.13 kJ/mol). These results showed that the nitrogen atom in the SNBDTC collector had a great influence on the adsorption strength of the collector on the mineral surface. This is due to the electron deposition behaviour of nitrogen atoms compared to the electron withdrawing character of oxygen and as such the SNBDTC showed better collecting ability than the PNBX. These results paved the way for the design of collectors for sperrylite and other arsenide minerals and suggested that nitrogen in a collector may significantly improve the ability of the collector for improved recovery. Keywords: Computational modelling, microcalorimetry, SNBDTC and PNBX collectors, adsorption energies

Jan 1, 2020

By J. W. Latilla, J. J. van Wijk

In late 1997 a request was received to assist with determining the powered support unit (shield) load capacities for the planned 2 seam short wall. This project had a number of aspects which made it attractive to utilize numerical modelling in conjunction with other more conventional design tools in the design of the shields. Amongst these were: The 2 seam panels were to be laid out about 25 m below the previously short walled 4 seam, the 4 seam had in turn been over-mined by the 5 seam long wall, the proposed face height of the 2 seam short wall was 5.5 m while the 4 seam had been mined at 4 m. The top seam in the area (5 seam) had been mined at between 1.5 and 2.2 m high, the face conditions with about 95 m of broken material applying dead weight loading to the 2 to 4 seam inter-burden septum were hard to predict and cyclical loading due to the presence of strong sandstone bands in the 2 to 4 seam inter-burden. The basic thrust of the study was to take the known, and successful, situation (4 seam short wall) and carry out comparative modelling to enable prediction of likely 2 seam conditions. Some two dimensional aspects studied were: 5 m goaf hanging up behind shields, stresses in beams to determine likely first goaf roof span, stresses in cantilever beams to asses cyclical loading due to sandstone bands in the interburden being loaded by the overlying goaf and stresses on chain and crush pillars adjacent to the goaf edge. Three dimensional aspects that were investigated included: Load distribution along face for close goafing and 5 m goaf hang-up and load in a 1 m wide rib modelled in the position of the powered support units. From the modelling it was possible to determine the optimal shield leg capacity of the new 2 seam equipment. These outputs were used when drawing up the technical specifications for manufacture of the new equipment. The face was successfully commissioned in August 2002. Fin 1997, requête fut faite pour aider à la détermination des capacités de charge pour l’unité de soutènement mécanisée (bouclier) pour la couche 2 courte taille en projet. Certains aspects de ce projet le rendaient intéressant pour utiliser la modélisation numérique en même temps que d’autres méthodes conventionnelles pour la conception des boucliers. Parmi ces aspects se trouvaient : Les panneaux de la couche 2 devaient être placés environ 25 m au dessous de la couche 4 courte taille ; la couche 4 avait été remplacée par la couche 5 longue taille ; la hauteur de taille proposée pour la couche 2 courte taille était 5.5 m, tandis que la couche 4 avait été exploitée à 4 m. La couche supérieure de la région (couche 5) avait été exploitée entre 1.5 et 2.2 m de hauteur ; il était difficile de prédire les conditions de taille, avec environ 95m de matériaux cassés ajoutant une charge morte à la plaque de séparation entre les couches 2 et 4 et un chargement cyclique causé par des bandes de grès dans l’entre-fardeau 2-4. L’idée principale de l’étude fut de prendre la situation connue et réussie (couche 4 courte taille) et de faire une modélisation comparative pour prédire les conditions probables de la couche 2. Certains des aspects à double dimension qui furent étudiés étaient : Un accrochage de remblai de 5m derrière les boucliers ; contraintes dans les poutres pour déterminer le premier intervalle probable entre remblai et toit ; contraintes dans les poutres en porte-à-faux pour évaluer le chargement cyclique causé par les bandes de grès dans l’entre-fardeau qui est accablé par le remblai et les contraintes sur les piliers par chaîne et d’écrasement adjacents au bord du remblai. Aspects à trois dimensions qui furent étudiés : Distribution de la charge le long de la taille pour les remblais proches et l’accrochage de remblai de 5 m et la charge dans une nervure de 1 m de large modelée dans la position des unités de soutènement mécanisées. La modélisation a permis de déterminer la capacité de portée optimale du bouclier du dispositif nouveau pour la couche 2. Ces résultats furent utilisés pour dresser les spécifications techniques pour la fabrication de l’équipement nouveau. La taille fut commissionnée avec succès en août

Jan 1, 2003