Search Documents

By S. Bradshaw, A. Mabentsela

"Physical and numerical modelling methods were followed to identify mechanism(s) for tundish slag entrainment in a bare tundish and one with a flow control device (FCD).The physical and numerical models made use of water and paraffin to model steel and slag respectively. Observations from the physical model showed that the steel-slag interface remains immobile in both cases. Entrained paraffin formed droplets approximately 1 mm in diameter. Results from both models (numerical and physical) showed that in both cases (bare and FCD case), areas of high entrained slag concentration exist near the inlet region. The entrained slag concentration decreases towards the tundish endwalls.Flow patterns and velocities tangential to the steel-slag interface from the numerical model showed that slag entrainment in both the bare tundish and tundish with a FCD possibly takes place via two mechanisms. First, the slag moves across the steel-slag interface via mass transfer; secondly small velocities tangential to the interface at depths greater than 10 mm below the interface carry the already ‘entrained’ slag into the bulk steel phase. These tangential flow patterns are dominant in the inlet region, hence the high concentration of entrained slag in this region. IntroductionThe tundish serves as the last metallurgical vessel through which steel passes before solidifying in the moulds. It is in the tundish that the last traces of non-metallic inclusions should be removed, otherwise the inclusions carry over to the moulds and cause defects in the steel product. In the tundish, the slag is less dense than the melt and thus resides on the top of the melt. The slag provides a sink into which the non-metallic inclusions float to and dissolve. The slag also protects the melt from air and heat loss. However, when slag is entrained in the melt as a result of increased turbulence or shearing at the steel-slag interface, slag can become a source of nonmetallic inclusions.Numerous studies on flow patterns in the tundish have been carried out since the introduction of the tundish. These studies were aimed at improving the flow characteristics in the tundish (Chattopadhyay, Isac, and Guthri, 2010; Cloete, 2014; Jha, Dash, and Kumar, 2001; Jha, Rao, and Dewan, 2008;"

Jan 1, 2017

By S. O. Choi, H. -S. Shin, W. -K. Song

Nuclear waste should be disposed with the best warranty for the national health and welfare. Among the several repository systems, the deep underground disposal is considered to be a most suitable system in Korean peninsula. However it demands basically the comprehensive stability analysis such as the behaviour of discontinuities in rock mass, the behaviour of ground water, and the reaction of rock stress according to the heat from the nuclear waste. For these purposes, the underground nuclear waste disposal repository was simulated in two- and three- dimensions. It shows that emphasis will be given to the thermal conductivity of discontinuities and the thermal convection of ground water as well as the thermal stress generated by the nuclear waste for design and construction of repository system, and they should be obtained from the field measurements. Déchets nucléaires devront tre déposés avec la meilleure garantie pour la santé et le bien public. Parmi les plusieurs systèmes de dépôt, la disposition en souterrin profond est considérée au système le plus approprié en Corée. Pourtant ce système demande essentiellement l’analyse éten-due de stabilité comme le comportement des discontinues en masse rocheuse, le comportement de l’eau souterrin et la réaction des contraintes de roche selon la chaleur depuis les déchets nucléaires. Pour ce but, le dépôt des déchets nucléaires en sous-sol a étè simulé en deux et trois dimensions. Il montre que l’accent sera donné à la conductivité thermale des discontinues et la convection thermale de l’eau souterrin aussi bien que la contrainte thermale générée par les déchets nucléaires pour le plan et la construction du systèmes de dépôt, et ils devront tre obtenus depuis les mesures sur place. Die Kernwüste muß mit der besten Gewähr für die nationale Gesundheit und die Wohlfahrt angeordnenet werden. Unter einigem Fundgrubesystem, das tief unterirdisch Wegwerfen werde in Betracht das passendest System in der koreanisch Halbinsel gezogen. Jedoch, es verlangt grundzätzlich die umfassend Stabilitätsberechnung so wie das Behnehmen mangelnder Konti-nuität in der Felsmasse, das Behnehmen des Grundwasser, und die Reaktion der Felsenbelastung nach der Hitze von der Kernwüste. Für diesen Zwecke, die unterirdische Wegferfenfundgrube der Kernwüste wurde in der zwei und drei Dimensionen gesimuliert. Es beweist daß die Betonung wird zur thermisch Leitfähigkeit mangelnder Kontinuität und thermisch Konvektion des Grund-wasser sowie die thermisch Belastung ergezeugt durch die Kernwüste für den Entwurf und die Konstruktion des Fundgrubesystem gegeben werden, und sie müssen von den Feldmaße ergelangt werden .

Jan 1, 2003

By A. F. Silva, J. M. G. Sotomayor, V. F. N. Torres

Geotechnical monitoring plays an important role in the detection of operational safety issues in the slopes of open pits. Currently, monitoring companies offer several solutions involving robust technologies that boast highly reliable data and the ability to control risky conditions. The monitoring data must be processed and analysed so as to allow the results to be used for several purposes, thereby providing information that can be used to manage operational actions and optimize mining plans or engineering projects. In this work we analysed monitoring data (pore pressure and displacement) and its correlation with the tension and displacement of the mass of an established failure slope calculated using the finite element method. To optimize the back-analysis, a Python language routine was developed using input data (point coordinates, parameter matrix, and critical section) to use software with the rock mass parameters (cohesion, friction angle, Young’s modulus, and Poisson’s ratio). For the back-analysis, the Mohr-Coulomb criterion was applied with the shear strength reduction technique to obtain the strength reduction factor. The results were consistent with both the measured displacements and the maximum deformation contours, revealing the possible failure mechanism, allowing the strength parameters to be calibrated according to the slope failure conditions, and providing information about the contribution of each variable (parameter) to the slope failure in the study area.

Oct 1, 2021

By K. Gharibi, A. Dehghani, S. Farrokhpay, M. Aghajanloo, M. Ostadrahimi

The effect of flotation operational parameters on froth stability and froth recovery was studied. Froth stability was measured using a special column. To determine the froth recovery, the froth height change model and froth height exponential model were used. It was found that since the interactions between the pulp and froth zones affect the time of froth formation, the exponential model is more suitable than the froth height change method for determining the froth recovery. The results showed that superficial air velocity and collector dosage have, respectively, the highest and lowest effect on the froth recovery, while froth recovery decreases sharply with increasing froth height.

Jan 1, 2021

By Y. Hwang, C Kang

To understand the effect of thermal loading from HLW on the groundwater flow nearby, the coupling of TH in an equivalent porous medium is studied. Results indicate that under given conditions the alteration of groundwater flow by decay heat is localized phenomena. More comprehensive studies are underway for THM coupling. Zum Verstandnis fur die Wirkung der thermischen Belastung von HLW in der Nahe von Grundwasserstrom, ist die Verbindung von TH in den entsprechenden porigen Medium erarbeitet. Die Ergebnisse zeigen, dass unter vorgegebenen Bedingungen die Anderung von Grundwasserstrom durch Zerfallwarme lokalisiert wird. Zusatzliche umfassende Arbeiten sind fur die THM Kupplung auf dem Wege. Pour comprendre l'effet du chargement thermique de HLW sur l'écoulement d'eaux souterraines tout près, l'accouplement du TH dans un milieu poreux équivalent est étudié. Les résultats indiquent que dans des conditions données le changement d'écoulement d'eaux souterraines par la chaleur d'affaiblissement est des phénomènes localisés. Des études plus complètes sont en cours pour l'accouplement de THM.

Jan 1, 2003

By B. Ceki, A. Mabentsela

The BCL furnace is scheduled to restart operations after being placed on care and maintenance in 2016 due to depressed nickel prices. The decision to start operations after such a stoppage ought to be led by a techno-economic evaluation of process options to make operations more resilient. For BCL, the decision lies between using the existing flash-smelting furnace (FSF) or a top-submerged lance (TSL) furnace. Available studies show that the FSF combined with other converting technologies is cheaper to operate; however, such studies are based on flowsheet simulation results of single copper concentrates and therefore do not provide a full scope of practical capabilities based on smelter operator skills. Using a t-test on normalized prior operational data from three Cu FSF and two Cu TSL, it was found that the only statistical differences between the operating costs of the FSF and TSL technologies are in the coal use for heating the feed blow and number of rebuilds: the FSF consumes coal to heat the feed blow and the TSL requires 2.4 rebuilds during a course of a single FSF campaign. A summative operating cost comparison over the existing BCL FSF 11-year life shows that BCL can decrease operational costs by some BWP 55.5 million if the operation were to change to the newer TSL technology. The savings derive from reduced coal use, which is normally associated with heating the blow when using the FSF. Despite the TSL carrying added costs of 2.4 rebuilds during a life time of one FSF furnace campaign, the cost associated with the TSL rebuilds of approximately BWP 1.3 million is minimal compared with the overall operational expenditure decrease that BCL will incur on using the TSL technology. In terms of the technology, BCL can have higher Ni–Cu recoveries at lower operational costs by elimination of Ni–Cu losses and eliminating the slag-cleaning furnace by converting to a TSL furnace.

Jul 10, 2024

It is almost eight years to the day when we launched the original SAMREC Code in March 2000. Since that date I think the SA minerals industry has matured beyond recognition in its approach to reserve and resource reporting, and I believe we can be justifiably proud of that progress. Many of those companies that have led the way in reporting standards are listed on our sponsors list. We thank them for their sponsorship but even more for their considerable support in all aspects of the SAMCODE organization. Matt Mullins, my co-speaker here today, has been instrumental in the revision of the SAMREC Code over a long period of time and also took up the reigns with the SAMVAL Code after the retirement of Rob Croll. I would like to formally thank Matt for his immense contribution in producing the two Codes; he can take great pride in the final product and fully deserves the many accolades that we have already received from our international counterparts. He has done all this whilst still maintaining a very demanding day job at BHPBilliton. Matt will be the first to admit that he has received tremendous support from more than 100 people who participated in the various working groups, many of whom are employed by our sponsors. There are obviously too many to mention by name but they deserve a big vote of thanks for their personal contributions. In addition to launching the two Codes we are also launching our ?branding? initiative with our own SAMCODE logo and the SAMCODE website: www.samcode.co.za. All the slides used in the presentation today will be on the website later today as will a newsletter which will serve as a media release.

Jan 1, 2008

By S. Stone

Because of problems encountered with conventional timber supports, a system of concrete sausageshaped support pillars was tested. The pillars are 3 m long, 0,6 m wide, and between 70 and 80 cm high (the height of the stoping width). They consist of bags filled with a grout of cement (slagment and sand in the ratio of I :2, and are installed in a staggered pattern 6 m apart on dip and 2 m apart on strike. These support packs have proved successful, and, although they cost more than the timber supports formerly used (R4,63 per cent are supported as against R2,26 for the conventional timber pack), their use is felt to be justified when account is taken of the costs of lost production and low productivity due to the bad hangingwall conditions that occurred with the conventional system.

Jan 1, 1978

By P. Vlasak, Z. Chara

Since the flow behaviour of slurry containing both coarse and very fine particles has not been sufficiently clarified, the paper focuses on the experimental study of the particle size distribution, time and intensity of shearing and the effect of chemical agents on the hydraulic gradient versus the average velocity relationship of fluidic ash slurries in the laminar and turbulent regimes. The recirculation pipe loop with smooth stainless steel pipes of inner diameters 26.8 and 36 mm was used for measuring the ash-water mixtures flow parameters. The dense fluidic ash-water mixtures behave as time dependent non-Newtonian slurries. Shearing, the addition of bottom ash or chemical agents, favourably affects the flow behaviour of dense fluidic ash-water slurries. The hydraulic gradient in the laminar region significantly decreases; also the laminar/turbulent transition region is reached for lower flow velocity.

Jan 1, 2007

Book review Pearson, J. S. Ocean floor mining. Park Ridge (New Jersey), Noyes Data Corporation, 1975. 201 pp. NIM reports Report no. 308 A mineralogical study of gold particles in pulp residues from the Bracken Gold Mine. (7th Mar.,1968. Re-issued Oct. 1975.) Report no. 377 Examination of pulp samples, treated with cyanide, for coated gold.(7th Aug., 1968. Reissued Oct.1975.) Report no. 385 The determination of the nature of coatings on gold particles. (2nd Aug., 1968. Reissued Oct. 1975.) Report no. 452 The Purlex Process - a description of the pilot plant leading to the use of the process in South Africa. (13th Jan., 1969. Re-issued Oct. 1975.) Report no. 482 Review of work on the treatment of pegmatites. (9th Apr., 1969. Reissued Sep. 1975.) Report no. 1443 Gravity concentration tests on four samples from Tantalite Valley,S. W.A. (5th Jul., 1972. Re-issued Sep. 1975.) Report no. 1489 The breakage of S oderberg electrodes. (10th Nov., 1972. Re-issued Nov. 1975.) Report no. 1545 A mineralogical investigation of leach residues from the Blyvooruitzicht Gold Mine. (22nd May, 1973. Re-issued Nov. 1975.) Report no. 1583 Preliminary tests on winnowing for the recovery of mica. (12th Nov., 1973. Re-issued Sep. 1975.) Report no. 1652 The identification of diamonds from Premier, Finsch, and Jagersfontein Mines by statistical analysis of data obtained from instrumental neutron-activation analysis. Report no. 1723 The determination of zirconium and aluminium in zirconiumaluminium alloys. Report no. 1739 The determination of trace amounts of noble metals in sulphate media. Report no. 1771 The determination of silver, selenium, tellurium, antimony, tin, lead, and arsenic in anode sludges. Report no. 1772 A study of copper recovery by lime roasting and leaching. Corrigendum The Special Issue of Volume 76 of the Journal ('Recent Advances in Mineral Dressing, October 1975) should be corrected as follows. The South African Institute Of Mining And Metallurgy - Information On Membershlp The Institute was founded in 1894 as the Chemical and Metallurgical Society of South Africa. In 1904 it was reconstituted as the Chemical, Metallurgical and Mining Society of South Africa and in 1956 it became the South African Institute of Mining and Metallurgy. Die Suid-Afrikaanse Instituut vir Mynbou en Metallurgie - Inligting Oor Lidmaatskap Die Instituut is in 1894 gestig as die Chemiese en MIetallurgiese Vereniging van ::!nid-Afrika. In 190-1is dit omvorm tot die Chemiese Metallurgiese en Mynbouvereniging van Sllid-Afrika en in 1956 het dit die Suid-Afrikaanse Instituut vir Mynbou en l\Ietallurgie geword.

Jan 2, 1976

This paper examines the new water-hydraulic (hydropowered) drill rigs that have been developed and proven in the last decade primarily in tabular, shallow-dipping, narrow-reef hard-rock South African mines. These include drill rigs for flat-end tunnel development, narrow inclined raises and winzes, large inclines and declines and longhole-based developments such as ore passes and vent raises. The hydropower technology rigs offer advantages both in safety and performance over traditional compressed-air-powered, hand-held development, and are generally more cost-effective than imported oil electro-hydraulic drill rigs. Furthermore, hydropowered rigs are inherently energy-efficient. The benefits of hydropower are discussed and a ?comprehensive development model? is presented which demonstrates that ore-bodies can be accessed in significantly shorter times. ?Localized? half level hydropower systems are introduced and a range of ancillary equipment available is listed.

Jan 1, 2012

By A. Chiappone, M. Barla, U. Rabagliati, L. Repetto

ABSTRACT: The paper describes the application of both continuum and discontinuum modelling to the study of the stability conditions of the Alpetto mine, a high rock cut located in Cesana Brianza (Italy). The main objective is to provide valuable information for future mine planning and for the assessment of the stability conditions of the abandoned high rock cuts. Continuum modelling involved the applications of the finite difference method, whereas the distinct element method was used for discontinuum modelling. RESUME: L'article décrit l'application des méthodes de modélisation continue/discontinue pour l'étude des conditions de stabilité de la mine d' Alpetto, située à Cesana Brianza (Italie). Le but du travail consiste à determiner des paramètres utiles vis-à-vis du projet et d'estimer les conditions de stabilité de l'amas rocheux au terme de l'exploitation de la mine susmentionnée. La modélisation continue a impliqué l'application de la méthode des différences finis alors que la méthode des éléments distincts a été utilisée pour la modélisation discontinue. KURZFASSUNG: Der Artikel beschreibt die Verwendung der Modellierung von continuum und discontinuum zur Untersuchung/Studium der Stabilitätsbedingungen von der Alpetto Mine, hohe Aushubsfront in einer Felsmasse die sich in der Gemeinde von Cesana Brianza befindet. Das Hauptziel dieser Arbeit ist die Festlegung von Parametern die zur Planung nützlich/behilflich sein können sowie auch die Möglichkeit zur Analyse/Auswertung der Stabilität der Felsmasse-Front nach Aufhebung der Nutzung derselben. Die continuum Methode/Analyse wurde verwendet durch Unterstützung der Finite Differenz Methode da man für die Analyse der discontinuum (Fels als discontinuum beschrieben) der Distinct Elemente Methode verwendet hat.

Jan 1, 2003

By I. M. Wolf, S. A. Usmar, L. A. Cornish

The limiting criterion in the use of stainless steel for certain forming operations such as coining is its hardness, which determines parameters such as required striking pressure, wear on dies, and integrity of pattern detail. Attention is given here to the development of ultra-soft ferritic stainless steels for coinage. In the first instance, the influence of carbon content on the striking properties of a series of commercial and experimental 17%Cr alloys was evaluated. It was found that a lower carbon content permitted the striking of relatively highly profiled and intricate patterns, provided that the hardness did not exceed 125 HV. Hardnesses as low as 115 HV were achieved in the fully annealed condition, but these alloys required high striking pressures. In a further study, three grades of experimental 14%Cr ferritic stainless steels were produced with a view to optimizing the ductility. When the residual impurities were minimized, hardness values of about 100 HV and lower were achieved. Micro-alloying additions allowed the heat-treatment response and grain size to be controlled. Excellent tensile properties, with elongations of up to 42 per cent, were achieved in the fuly annealed condition, and highly profiled patterns were produced in coining trials.

Jan 1, 1993

By A. V. Aleksandrov, T. N. Aleksandrova, N. V. Nikolaeva

Using complex thermal analysis methods, flotation concentrates were classified depending on what the organic and nonorganic carbon form is. The possibility of ultrafine particles of valuable components (noble metals and diamonds) extraction using physical actions of different genesis in the processing of ‘unconventional’ mineral raw materials is considered in the paper. Electromagnetic treatment is one of new technologies in the field of mineral processing. The features of the electromagnetic effect on substances include uniform heating throughout of the volume, high speed and low inertia of heating, as well as the possibility of selective heating. A selection of studies including gravity, flotation and extraction methods of enrichment using energy effects, as well as thermal analysis was conducted to establish the availability and possibility of extracting valuable components. Due to microwave and high-temperature exposure, minerals and gas-liquid inclusions are decremented, and crystal-chemical water is released, resulting in additional defects. As a result, self-cleaning of sulphide minerals from atoms of scattered gold occurs by distilling it into peripheral parts of grains and intergranular space, where ultradispersed individuals are formed. Keywords: Refractory gold-bearing ores, physico-chemical properties, ore preparation, flotation, modelling, simulation, selection

Jan 1, 2020

By S. Ata, Y. Pan, S. Gautam, G. Bournival

Bubbles play a vital role in flotation, and their properties directly affect the flotation performance. Xanthates are one of the major collectors used in sulphide mineral flotation. It is often believed that their main function is to render the desired mineral surface hydrophobic, which is essential for the mineral particles to attach to air bubbles. This paper takes a systematic approach to assess the influence of potassium amyl xanthate (PAX) at the air–liquid phase and its interaction with the frother in the concentration of range 10–5×104 ppm. Bubble size was measured in a laboratory flotation cell using a photographic technique and the stability of bubbles was quantified in terms of coalescence time -, the time required for a bubble pair produced at adjacent capillaries to merge into a single bubble. Bubble size reduction of up to 26% was observed with increasing PAX concentration in the cell. The bubble coalescence experiments using PAX only showed that the bubbles coalesced quickly at lower concentrations (10–50 ppm), but they stayed extremely stable at higher concentrations (1×102–1×104 ppm). Further experiments were carried out where the concentration of PAX was fixed at 1 ppm and 4- Methyl-2-pentanol (MIBC) concentration was varied. The synergetic action of PAX and MIBC significantly improved the stability of bubbles in the mixed system, and is even compatible with a stronger frother. The results strongly suggest that the role of PAX at the air–liquid phase should be considered in the practice of sulphide flotation. Keywords: Bubble size, bubble coalescence, PAX, bubble stability

Jan 1, 2020

By J. A. Batista-Rodríguez, F. J. López-Saucedo

A new methodology is proposed for the preliminary assessment of coal blend quality, which combines gamma-ray spectrometry and magnetic susceptibility measurements. This methodology does not replacethe conventional methods of assessing coal quality, but can help to control the quality of the coal blending process, as well as reduce the amount of proximate analysis required and the determinations of calorific value and total sulphur. The methodology includes five steps. First, both geophysical measurements aremade with handheld equipment. The samples with magnetic susceptibility ≤ 1 × 10-3 SI are then separated. From these samples, those with total gamma intensity ≤ 20 nGy/h are separated. These samples have a higher calorific value and lower ash and moisture content. To separate the samples of better quality and with lower total sulphur content, in step four the samples with total gamma intensity > 20 nGy/h are separated from those with magnetic susceptibility ≤ 1 × 10-3 SI. This last group includes samplesthat will cause less total sulphur-related environmental pollution. In the final step, the quality of both radioactive sample groups is corroborated from the calorific value measurement and ash, moisture, andtotal sulphur contents in at least 10% of all coal blend samples from both groups. In this study, more than1000 samples were analysed with this new methodology, and the results are remarkably similar to the ASTM classification of the Sabinas Basin coals.

Apr 2, 2022

By L. Uotinen, M. Rinne, R. Mishra

Underground mining gives rise to geotechnical hazards. A formal geotechnical risk assessment can help to forecast and mitigate these hazards. Frequentist probability methods can be used when the hazard does not have many variables and a lot of data is available. However, often there is not enough data for probability distributions, such as in the case of new projects. The risk assessment is often subjective and qualitative, based on expert judgement. The purpose of this research is to present the use of Bayesian networks (BNs) as an alternative to existing risk assessment methods in underground mines by combining expert knowledge with data as it becomes available. Roof fall frequency forecasting using parameter learning is demonstrated with 1141 sets of roof fall data across 12 coal mines in the USA. The prediction is nearly identical for individual mines, but when multiple mines are evaluated it is difficult to find a single best fit distribution for annual roof fall frequency. The BN approach with TNormal distribution was twice as likely to fit the observed data compared to the Poisson distribution assumed in the past. A hybrid approach using BN combining multiple probability distribution curves from historical data to predict annual roof fall is proposed. The BN models can account for variability for multiple parameters without increasing the complexity of the calculation. BNs can work with varying amounts of data, which makes them a good tool for real-time risk assessment in mines.

Jun 1, 2021

By M. Pötsch, W. Schubert, A. Goricki

Geological and geotechnical data are essential for the design of tunnels. To determine the rock mass behavior and the support of a planned tunnel excavation a consistent method for rock mass characterization and excavation and support determination has been developed. Probabilistic data processing with analytical methods is used for the quantification of the procedure and allows an evaluation of the applicability and the technical risk of different excavation and support methods. The sensitivity of the procedure on selected input parameters is highlighted in a parametric study. Finally an application of the procedure illustrates the use of the described method of probabilistic excavation and support determination for tunnels. Des données géologiques et géotechniques sont décisives pour la planification d’un tunnel. Pour la détermination du comportement des strates, le choix du soutènement et de la méthode de progression une description compréhensible de la montagne a été développée. À l'aide d'un traitement de données probabiliste, la procédure proposée est transposée quantitative sur une base de méthodes analytiques. De cette manière l'évaluation des méthodes de construction et la détermination du risque technique deviennent possibles. La sensitivité de la procédure de différents paramètres d'entrée est représentée dans une étude de paramètre. Pour finir, l'application de la procédure décrite est montrée à l’aide d'un cas pratique. Geologische und geotechnische Daten sind entscheidend für die Planung von Tunnels. Für die Ermittlung des Gebirgsverhaltens und der Festlegung von Ausbruch und Stützung wurde ein nachvollziehbarer Ablauf der Gebirgsbeschreibung entwickelt. Mit Hilfe von probabilistischer Datenverarbeitung auf Grundlage analytischer Methoden wird die vorgeschlagene Prozedur quantiativ umgesetzt. Dadurch werden die Bewertung von Baumethoden und die Ermittlung des technischen Risikos ermöglicht. Die Sensitivität des Verfahrens von einzelnen Eingangsparametern wird in einer Parameterstudie dargestellt. Abschließend wird anhand eines Beispiels die Anwendung des beschriebenen Verfahrens gezeigt.

Jan 1, 2003

Report M294 A mineralogical investigation of potential gold-sorbing minerals and shales, by c.T. Logan. Dec. 1986. 12 pp. Computer software The Fifth IFAC/IFIP Symposium on Software for Computer Control (SOCOCO 88) is to be held in J ohannesburg from 26th to 28th April, 1988. Tunneling 88 The Institution of Mining and Metalurgy, with the cooperation of the British Tunneling Society, the Institution of Mining Engineers, and the Transport and Road Research Laboratory, Department of Transport, is pleased to announce the fifth international symposium, Tunneling 88, which wil be held in London, England, from 18th to 21st April, 1988. Ion-exchange processes ION-EX '87, an international conference and industrial exhibition on the industrial, analytical, and preparative applications of ion chromatography and ionexchange processes, wil be held in Wrexham (North Wales) from 13th to 16th April, 1987.

Jan 1, 1987

By Marek Dworzanowski

Dense medium separation (DMS) is critical to the operation of coal and diamond beneficiation plants. It is also utilised in iron ore, manganese, chromite and andalusite beneficiation as well as pre-concentration for platinum-bearing UG2 ore. Gravity concentration plays an important role in the processing of diamonds, coal, gold, platinum, titanium minerals, zircon, chromite, iron ore and manganese. The DMS and Gravity Concentration operations and technology in South Africa conference will focus on the operation of DMS and Gravity Concentration circuits in the South African Mining Industry. The current status of the technologies and equipment employed will be presented as well as future developments. The conference was set up to showcase South African DMS and Gravity Concentration operations and provide a forum where operators, technology and equipment suppliers can engage in knowledge sharing. The papers cover a wide spectrum of topics, including descriptions of operations, optimisation projects, new capital projects, equipment applications, process monitoring and process selection. Most commodities and unit processes associated with DMS and Gravity Concentration are covered. The conference venue was selected to be the CSIR Convention Centre in Pretoria. The CSIR has contributed to DMS research in South Africa and it is located not far from many coal, diamond, gold, platinum and chrome mines that extensively utilise DMS and Gravity Concentration in their beneficiation plants. I believe that the papers and presentations submitted for this conference will provide a valuable future reference for DMS and Gravity Concentration, thus making the work of all the contributors to this conference highly rewarding and worthwhile.

Jan 1, 2006