Search Documents

By Benjamin Petkof

Production quarry blasts in three rock types were photographed with a high-speed camera. Analysis of the films showed that step increases sometimes occur in the horizontal velocity of the broken rock. These step velocity increases were observed only in the first foot or so of rock movement. This observation indicates that the gaseous products of the explosion do additional work on the rock after it is crushed and cracked by the initial compressive-stress pulse and the reflected tensile-stress pulse. The observed initial fly-rock velocity is compared with the calculated fly-rock velocity for reflection spalling. A mechanism possibly causing the velocity increases is discussed. INTRODUCTION When a small concentrated charge of explosive is detonated at the bottom of a drill hole near a free surface, two modes of rock failure have been observed; both are associated with the stress pulse generated in the rock by the detonating explosive. The first mode of failure is the crushing and radial tensile cracking associated with the initial passage of the compressive-stress pulse as it propagates outward from the explosion. This type of rock failure is usually confined to the immediate vicinity of the charge hole. The second mode of failure is the tangential and radial tensile cracking associated with the tensile-stress pulse that is reflected from the free surface. This mode of failure is commonly called scabbing or spalling and has been shown to be a primary cause of rock failure in crater formation at one free surface. (3).4

Jan 1, 1961

By Frank J. Susko

The U.S. Bureau of Mines has developed a computer model to describe a flotation process. Coal data from conventional flotation has been converted to a simple, two-parameter kinetic model developed by Reuter and van Deventer (1,2)3. Each set of coal data was represented by two constants, a and ß, and an average flotation rate. The success of the model was demonstrated when the calculated and experimental recoveries showed good correlation. The two-parameter model allows complex data to be defined much more efficiently than traditional knowledge-based models.

Jan 1, 2010

By Laurance L. Oden

The Bureau of Mines conducted corrosion tests of 18 commercial alloys in H3 P04 -phosphate rock or A1,03 slurry, in 10 pct HF, and in 25 pct H2 SiF6 to simulate three environments anticipated in a Bureau process to extract fluoride values from phosphate rock. Small alloy coupons were rotated in duplicate tests at 4.4 to 21 fps in the slurry at 170° C to determine rates of erosion-corrosion. At 4.4 fps the lowest rates, in mils penetration per year (mpy), were measured for Hastelloy C-276 (<20), Hastelloy B (30), and Inconel 625 (150);the rates increased at 21 fps to 55 mpy, 45 mpy, and 1,000 mpy, respectively. The corrosion rate for all alloys exceeded 40 mpy in either the equilibrium vapor or liquid phases of aqueous solutions containing 10 pct HF or 25 pct H2SiF6 at 100° C. Uniform corrosion in 10 pct HF at 50° C was observed only for Inconel 625 (22 mpy), Hastelloy C-276 (43 mpy), and Illium 98 (17 mpy). Inconel 625 (0.75 mpy), Hastelloy C-276 (1.3 mpy), Illium 98 (1.7 mpy), and Incoloy 825 (0.45 mpy) were attacked uniformly in 25 pct H2SiF6 at 50° C.

Jan 1, 1974

By D. E. Wolfson

Destructive distillation (carbonization) was shown to be a feasible method of disposing of scrap tires. The Bureau of Mines conducted tests under a variety of conditions. Solid, liquid, and gaseous products were produced, recovered, and analyzed. The quantities of the various products were shown to be quite dependent on the test temperature. Variability in composition of the liquid and gaseous products with changes in test temperature was also significant.

Jan 1, 1969

By H. H. Fields, Joseph Cervik, G. N. Aul

Coal is a soft and brittle material. Drilling rates in the Pittsburgh coalbed using a drag bit exceed 3 ft/min at 2,500-pound thrust. However, maintaining the bit on a horizontal trajectory or parallel to bedding planes to attain lengths of 1,000 feet is difficult. This Bureau of Mines report presents a drill string configuration that can be guided through the coalbed. The angle of the borehole is measured periodically and by proper combinations of bit thrust and rotational speed (r/min), bit trajectory can be lifted or dropped to keep the bit in the coalbed. An example of a hole drilled to 2,126 feet is presented to show levels of thrust and rotational speed used to lift or drop the bit, the seemingly unexplainable events that occur, and the strategy used during drilling. Thrust levels during drilling range from 600 to 2,500 pounds. Hydraulic motors powered by a 30-hp, 440-volt motor provide ample power for drilling horizontal holes 2,000 feet long.

Jan 1, 1975

By Walter R. Storms, Jerry W. FAUST

This paper, which describes mining methods and costs at the Kearney zinc-lead mine, is one of a series being prepared by the Mining Division of the Bureau of Mines on mining practices, methods, and costs in varicus mining districts of the United States. The Kearney mine, which is owned by the New Mexico Consolidated Mining Co., a subsidiary of the Peru Mining Co. (Illinois Zinc), is situated a few miles southeast of the town of Hanover, in the northwest corner of sec. 27, T. 17 S., R. 12 W., in the Central Mining District, Grant County, N. Mex. (Figs. 1 and 2.) This report presents a brief history of the district, describes the geology, and outlines methods of prospecting and exploration, including eampling and estimation of tonnages and values. Development and mining methods are explained, and transportation, ventilation, drainage, safety measures, and organizatich are described. The wage scale and mining costs comprise the concluding sections of the report.

Jun 1, 1949

By Roger J. Morrell

The Bureau of Mines conducted drag cutting experiments in hard, abrasive rock in an effort to extend the capabilities of an experimental kerf-core mining machine. The basic kerf-core mining machine cannot be used in hard, abrasive rocks because of the high wear experienced by the kerf cutters. These experiments were conducted in an effort to develop a method of preweakening the rock ahead of the kerf cutters in order to reduce the high cutting loads and hence the higher wear rates experienced by the cutters. The two "preweakening" techniques studied were indenting with mechanical wedges and single and double slotting with diamond saws. The best cutter force reduction achieved with mechanical indenting as 70 pct, whereas double slotting achieved force reductions of up to 99 pct. Conceptual designs of preweakening systems that could be retrofitted onto the basic kerfing cutterhead were developed for both the indenting and the slotting techniques. A high-energy impactor with wedge bit was used for the indenting method, and high-pressure water jets were used for the slotting method. A preliminary technical and economic analysis was performed for both of these full-scale systems to illustrate the methodology and to point out the important technical and economic factors that must be considered.

Jan 1, 1987

By Wesley A. Grosh

The Allah Cooper mine, in Louisa County, Va., formerly was a producer of lead and zinc. It was believed that the critical shortage of leach and zinc and the fact that some ore had been produced at this mine justified exploration of it. A preliminary examination was made on April 30, 1943, by J. E. Hill, a Bureau of Mines Engineer. Diamond drilling was done on the property from November 30 to December 18, 1943, to determine whether the sulfide body extended to depth. One hole drilled to a depth of 650 feet and located so as to cut the Allah Cooper ore shoot about 150 feet below the lowest known mine workings failed to disclose sulfide vein at that depth.

Jan 1, 1949

By P. Comba

The U.S. Bureau of Mines investigated a hydrochloric (HC1)-calcium fluoride (CaF2) leaching procedure to treat domestic manganese (Mn)-bearing silicate resources. The proposed process is an alternative to high-temperature and energy-intensive extractive techniques. Single-stage leaching with a stoichiometric amount of HCl and a F-Mn mole ratio of 0.2 extracted 96 pct of the Mn when the leach conditions were 50° C, 3 h, and 35 pct solids. Ninety-eight percent of the Mn was extracted during countercurrent leaching at similar conditions. A process flowsheet was developed that incorporated HC1-Cab leaching, excess leach acid utilization, fluoride (F) recycle, and Mn recovery. When the domestic manganese silicate ore was processed, 98 pct of the Mn was extracted, 99 pct of the Cab was reclaimed, and a leach residue was produced that passed the Environmental Protection Agency (EPA) Extraction Procedure (EP) Test for nonhazardous waste.

Jan 1, 2010

By David R. Hanson

Experimental work performed by the Bureau of Mines in a laboratory environment has shown that the formation of failure zones within certain rock types is accompanied by the emission of significant amounts of radiofrequency (RF) electromagnetic (EM) energy. This radiation was detected using nonresonant, "electrically short," broad-band antennas. Rock types for which emission was observed include granite, quartzite, and taconite; sandstone and marble did not emit measurable radiation. Amplitude spectra of the radiation showed the energy to be concentrated between 10 and 40 kilohertz. These data indicate that emission is directional, but this has not yet been proven. In addition, amplitude of RF emission increases with increasing crack size. Since emission was observed only for brittle quartz-bearing rocks, it appears the formation of piezoelectric fields is a necessary condition for RF radiation. Plausible mechanisms for emission include rapid decay of piezoelectric fields accompanying the sudden stress release at failure and/or the acceleration of an "exoelectron plasma" through the intense local piezoelectric fields. Since emission appears to increase with the scale of failure, and since antennas do not need to be coupled directly to rock surfaces as with conventional geophones, the possibility of developing a portable system to monitor seismically active areas exists.

Jan 1, 1981

By G. W. Jones, R. E. Kennedy

Most gasolines and naphthas are mixtures of paraffin- series hydrocarbons and comprise such substances as pentane , hexane , heptane , octane , and others up to perhaps dodecane . Many of these hydrocarbons , when mixed with the proper proportions of air and ignited , are highly explosive . It is due to this characteristic that gasoline has become so important as a fuel in internal -combustion engines . Gasoline and naphtha also are used in the industry as solvents and cleaning agents . Because of their explosive properties they are dangerous to use unless the composition is so chosen that the vapor pressure of the mixture is not high enough to produce explosive mixtures with air at the temperature at which they are used . Hydrocarbon mixtures may be made less hazardous by adding some incombustible liquid , such as carbon tetrachloride . Barrier reports the amount of carbon tetrachloride that must be added to different naphthas to render such mixtures free from fire and explosion hazards . He found that the amount of carbon tetrachloride that must be present in the final mixture of naphtha and carbon tetrachloride varied with the density of the naphtha . Of the naphthas tested the amount of carbon tetrachloride necessary to render such mixtures free from fire and explosion hazards ranged from 30 to 70 percent . .. Determination of the fire and explosion hazards of carbon tetrachloridehydrocarbon mixtures would be easy if the boiling points and vapor pressures of the two were the same at any given temperature . The fact that carbon tetrachloride boils at 76° C. while the boiling points of the hydrocarbons found in gasoline and naphtha may range from 37° , the boiling point of pentane ,

Nov 1, 1934

By C. K. Man

Coal dust explosions are routinely conducted within the full-scale experimental mine at the National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory?s (PRL) Lake Lynn Experimental Mine (LLEM) to meet the needs of numerous safety and health research programs. Many of these explosion tests over the years involved igniting different coal dust and limestone rock dust mixtures (up to 80% by volume rock dust). Following four more recent tests, floor dust samples have been collected and analyzed using the alcohol coking test and scanning electron microscopy (SEM) and the results compared to estimate the flame travel.

Jan 1, 2009

By P. W. Jerant

The methane emissions from an advancing coal mine section were continuously monitored for 120 days. During this time, the section advanced 2,000 feet into virgin Pittsburgh coalbed producing 54,565 tons of coal with a total methane emission of 91 million ft3. Analysis of the data gathered showed that daily methane emissions did not correlate with overburden thickness and daily coal production. A good correlation was found between the daily methane emission and the average length of rib exposed to virgin coal.

Jan 1, 1976

By Richard J. Mainiero

The U.S. Bureau of Mines in cooperation with Jim Walter Resources, Inc. (JWR), Brookwood, AL, evaluated the use of sheathed explosive charges in breaking up large stones that can jam the feeder¬breaker or pan conveyor on longwalls and halt operations. Use of the sheathed charge reduced the downtime of the longwall panel to 15 to 30 min as compared with the 1 to 2 h required to drill and shoot the stone. Firing the sheathed charge at the face caused no significant damage to Iongwall equipment. Use of the sheathed charge also represented an improvement in safety by eliminating the exposure of miners to the inherent hazards of the face for extended periods of time. Another benefit, which is difficult to quantify, is the elimination of the temptation to shoot mudcaps or adobes, which is illegal in U.S. underground coal mines.

Jan 1, 1990

By P. L. Loyselle, B. D. Comilsen, D. H. Carlson, J. H. Johnson

"In-mine airborne particulate samples have been successfully collected and the relative amounts of diesel and coal determined using the Laser Raman Quantitative Analysis (LRQA) method. This method allows analysis of filters which have been collected by a method similar to that used to determine the airborne respirable dust concentration in us underground coal mines. Samples were taken near the feeder-breaker, on haulage vehicles, and in the returns. Sampling methodologies were developed for coal-only and diesel-only particulate reference samples with sufficient filter loading for the LRQA method. A statistical analysis of reproducibility has been carried out. Samples have been collected simultaneously at two locations using the LRQA and the size-selective sampling methods. Good agreement between the two methods has been found.INTRODUCTIONThe goal of this research has been to develop the Laser Raman Quantitative Analysis (LRQA) method to measure the composition of respirable particulate, i.e. the fractions of coal and of diesel particulate, in the mine ambient air. In earlier Bureau of Mines sponsored research, we successfully demonstrated that the LRQA method could be used to measure the fraction of Diesel Particulate Matter (DPM) in coal/diesel particulate mixtures which were prepared in the laboratory.(I) 'The immediate objective was to test and refine this LRQA method on samples collected in a diesel underground coal mine.Specific objectives required to meet this goal include:I) Develop in-mine sample collection methods which will insure sufficient particulate loading on filters for LRQA. ,2) Develop methodology for in-mine collection of reference samples (""coal-only"" and ""diesel-only"" filters) which arc required for quantitative LRQA. 3) Analyze precision and accuracy of the LRQA method. 4) Compare composition measurements with another analytical method, i.e. the University of Minnesota/Bureau of Mines size selective sampling Micro-Orifice Uniform Deposit Impactor (MOUDI) method.An advantage of the LRQA method is that it allows analysis of filters which have been collected by a method similar to that used to determine the respirable dust concentration in US underground coal mines. No new sampling instruments and techniques are required. Transfer of sample from collection substrate to analysis substrate is not necessary. Furthermore, other analyses can be made on the same sample since the technique is nondestructive."

Jan 1, 1988

By D. Harrington

The occurrence of dusts in underground workings creates many difficult and, in some instances, contradictory and conflicting problems for workers, operators, and all others interested in health and safety in mining and tunneling. Moreover, there are many misconceptions both as to the actual effect of most dusts which may be encountered in underground work and as to remedial or alleviating measures. Although the harmfulness of mine dusts to health of miners has been mentioned by man; writers in ancient times, much of our really authentic knowledge of the effect of underground dusts upon health or safety in both coal and metal mines has been pained during the past 30 or 35 years. There has been, however, a considerable amount of generalizing from some local condition or occurrence or theory rather than arriving at conclusions after extended studies and observations made not only in mines and tunnels but also in town, camps, and plants, and comprising date on as many different mining and tunneling localities, conditions, etc., as could be secured with reasonable expenditure of time or money. This paper dives sortie observations based on the writer&apos;s 30 odd years of experience in and around both coal and metal mines, including approximately 20 years? close study of dust disease with detailed surveys and reports on dust occurrence and effects in considerably more than 100 mines in probably 20 States of the Union. The observatio are those of an engineer and in many respects conflict the with "going" ideas of doctors, pathologists, and others who have written on dust disease. Were the word dust is used in this p: per in connection with respiratory disease, it refers to solid particles which float or can float in the air breathed by workers. Although these particles are usually dry, they may be wet; in general, their dimensions are so small as to be invisible to the nailed eye. Dusts in coal mines which may be involved in the initiation or extension of explosions, are generally thought to be those which are smaller than 20-mesh in size but chiefly finer than 20-mesh; coal-mine dusts which are harmful to health of workers have essentially the same general physical characteristics as other dusts, but usually consist of smaller particles.

Jan 1, 1936

By C. C. Merrill

Columbium, tantalum, titanium, and zirconium are present in solid waste products generated by the chlorination of rutile used for production of titanium tetrachloride (TiC14). The columbium and tantalum were separated from titanium and zirconium by liquid-liquid extraction techniques using a secondary amine. Salts of these elements are in a leach liquor produced by water leaching of mineral waste from the chlorination of rutile. This waste, produced at the rate of approximately 50,000 tons per year, is about 40 wt pct water soluble. Leach liquors, separated by filtration, were further separated into a solid fraction and a liquid fraction by pressure hydrolysis, The solid fraction containing Cb, Ta, Ti, and Zr was dissolved in HC1-HF and used as a feed solution. Columbium and tantalum were removed from the organic extractant with 1 [N] HC1. A miniature 10-stage reactor showed that the columbium and tantalum present in solution could be separated with a continuous flow.

Jan 1, 1972

By J. A. Rowland

Manganese-copper alloys containing 60 percent or more electrolytic manganese exhibit an unusual combination of high vibration damping capacity with good strength properties. Properties of the pure alloys were first studied in the laboratories of the Federal Bureau of Mines and have been described in a series of technical papers1/ published from 1941-49. The unusual characteristics of these manganese-copper alloys attracted the attention of research metallurgists and several additional investigations have also been reported in the literature.2/ The engineer, also, was attracted by the combination of high strength and high vibrational damping capacity possessed by these alloys. A wide field of application in structural and machine design was obvious. However, serious difficulties encountered in commercial fabrication of structural or machine components from the alloys retarded attempts at their practical utilization. For this reason the Federal Bureau of Mines, in cooperation with the United States Navy, Bureau of Ships, undertook a program designed to develop practical methods for fabricating a selected group of the high-damping alloys. It is the purpose of this paper to summarize a part of that investigation in a form suitable for use by the metallurgist interested in commercial fabrication of the alloys.

Jan 1, 1955

By Steven J. Page

Accurate measurement of workplace respirable dust concentration is an essential step in eliminating lung disease in any occupational setting. In the United States (U.S.) coal mining industry, this measurement process has relied upon a personal sampler that includes a 10 mm Dorr-Oliver (DO) nylon cyclone operated at a flow rate of 2.0 L min-1 to collect a respirable dust sample. Dust concentrations measured with this sampler are multiplied by 1.38, which was empirically derived, to convert them to measurements approximating the United Kingdom British Medical Research Council (BMRC) definition of respirable dust upon which the health effects of coal mine dust are based. The International Organization for Standardization (ISO) subsequently refined the respirable dust definition and the U.S. National Institute for Occupational Safety and Health (NIOSH) 1995 Criteria for a Recommended Standard presented a conversion multiplier of 0.857 to apply to the 2.0 L min-&apos; DO (in addition to thel.38 multiplier) to obtain equivalent ISO concentrations, as approximated by the 1.7 L min-1 DO. However, the conversion multiplier 0.857 was derived indirectly from a limited size distribution data set rather than a direct comparison of the DO samplers. The present analysis focuses on providing a more accurate conversion multiplier derived from direct comparisons of the 2.0 L min-1 (with 1.38 BMRC equivalency multiplier) and 1.7 L min-1 DO cyclones. A weighted linear regression analysis of this database suggests that a more accurate estimate of the conversion multiplier is 0.815.

Jan 1, 2009

By W. N. Marchant

The Bureau of Mines improved removal of selenium from zinc smelter acidic gas scrubber effluent by using zinc dust to precipitate soluble selenium prior to lime neutralization. Lime neutralization alone decreased selenium in the waste water from, typically, 6 parts per million to 2 parts per million, whereas the use of zinc dust precipitant gave an effluent containing less than 0.1 part per million of selenium. The waste treatment operation first was developed on a laboratory scale and later was successfully tested at a smelter site on a 1-gallon-per-minute basis. During the research a simple and rapid means was developed for determining selenium in waste water; the technique enabled visual semiquantitative selenium determinations that later were confirmed quantitatively by X-ray fluorescence.

Jan 1, 1978