Search Documents

By Andrew D. O. O’Brien, Linda J. McWilliams, Joe L. Howell, Douglas E. Pollock, Jeanne A. Zimmer, Andrew B. Cecala

A quick, safe, and effective method has been developed that allows workers to clean their dust laden work clothing periodically throughout the day. For the mining industry, this technique is much more effective than the current federally approved method of using a vacuuming system. This newly designed method is relatively inexpensive and can be easily installed at any operation to allow workers to clean their clothing without contaminating the worker, the work environment. or co-workers to elevated respirable dust levels. This clothes cleaning process uses an air spray manifold to blow dust from a worker's clothing in an enclosed booth, which combines the dust for capture and removal by a baghouse dust collector. Since the air exhausted by the dust collector causes the booth to be under negative pressure. no measurable quantities of dust were ever measure escaping from the booth to contaminate the work environment and/or other workers. The worker performing the cleaning process is required to wear a half-mask fit- tested respirator with an N 100 filter, hearing protection, and full seal goggles. Dust samples taken inside the respirator of test personnel performing the clothes cleaning process showed very minimal to no respirable dust. This clothes cleaning process was performed in less than 20 seconds and was significantly y cleaner than either the Federally approved method of vacuuming, or the most common method or using a single compressed air hose. It was also determined during this research that polyester-cotton blend coveralls clean more effectively than coveralls which are 100 percent cotton. The newly designed clothes cleaning process has potential application to any industry where workers' clothing becomes contaminated with most any type of dust or product.

By A. W. Hall

Cylindrical plastic scintillators were investigated for efficiency in detecting neutron-induced prompt gamma rays. Scintillator performance was compared on the basis of half-resolution and peak-to-trough ratios for gamma spectra obtained from Co-60 (1.17 and 1.33 MeV), Th-228 (2.62 MeV), and PuBe (4.43 MeV). Various sizes of Pilot Chemical scintillators (types B, F, M, and Y) were tested. The best half-resolution, 7.7 percent for PuBe, was achieved with a 5-by 5-inch Pilot Y?scintillator and dual photomultipliers. Comparison with sodium iodide (NaI) scintillators and the use of plastic scintillators for on-stream analysis of sulfur in coal is discussed. Plastics were found to be unsuitable for on-stream analysis of materials having complex prompt gamma ray spectra; however, they could conceivably be used for those yielding Simpler spectra.

Jan 1, 1974

By F. Varley

Researchers from the National Institute for Occupational Safety and Health (NIOSH), in cooperation with mine operators, conducted a study of heat stress exposures among mine rescue workers in underground mines. Mine rescue workers face extreme heat loads as they enter hot and poorly ventilated environments, particularly when they are wearing breathing apparatuses. The burden of wearing a closed-circuit breathing apparatus (CCBA), the inability to drink fluids for extended periods of time, and the potential for ventilation disruptions and fires combine to increase the risk of heat illness during a response to an emergency. In this research, ambient environmental conditions and heat strain indicators were measured using conventional ventilation monitoring tools during mine rescue training exercises. Heat strain was measured with an ingestible temperature-sensing pill that measured core temperature continuously. In addition, a heart-rate monitoring chest strap was used to indicate physical strain resulting from physical activity and heat. Both core temperature and heart rate data were transmitted to a remote recorder worn by a rescuer and time-stamped. Team activities were also observed to determine the contribution of work rate to a person’s total heat load. The effectiveness of several engineering controls, such as cooling the air inhaled by rescuers through an apparatus, wearing cooling vests, and supplying water through the CCBA masks, were investigated. Administrative controls, such as limiting the duration of exposure and controlling the work rate through forced-rest regimens, were also evaluated. Results to date are discussed, and tools for evaluating team condition and estimating the length of time it would be safe for rescuers to work are proposed.

By Thomas W. Martin

This chapter includes tables from 1984 that were not available in time for publication of the 1984 Minerals Yearbook, but does not include corresponding tables for 1985. The value of raw nonfuel minerals produced in the United States during 1985 was estimated at $23.2 billion, an increase of $0.07 billion over the value for 1984. This is the third consecutive year that the value has increased, and except for a decrease in 1982, the value for each year has increased since 1971, or 13 out of 14 years. However. while the value of industrial minerals production continued to grow, reflecting the growth of the domestic economy, the value of metal mine production decreased in 1985 by 6%. This drop was more than offset by a 3% increase in the value of industrial minerals production because the value of industrial minerals produced was more than three times larger than the value of metals. The decrease makes 1986 the third year in the past 5 years in which a drop in the value of metal mining production occurred in the United States where production continued to lag behind growing world production. Domestic production of such major commodities 88 aluminum, copper, iron ore, phosphate rock, and zinc continued to decline owing to a number of international and domestic factors. Gold continued to be the most active commodity in the domestic metal mining industry. Despite lower prices, gold output increased to 2.5 million troy ounces, a 19% increase over that of 1984. The estimated annual production capacity of new gold mines beginning production exceeded 1 million ounces.

Jan 1, 1987

By Robert C. Ellman

The Bureau of Mines studied lignite pulverization in a laboratory ring-roller mill. Both moisture content and the source of lignite were found to be important factors in pulverizer operation. Reduction of moisture content increased capacity and reduced power consumption, but predrying is more effective than in-the-mill drying in improving pulverizer operation. A combination predrier-crusher system produced significant improvements but other efforts to improve in-the-mill drying in the test mill were unsuccessful. Pulverization of frozen lignite was found to seriously reduce pulverizer capacity and increase power requirements.

Jan 1, 1972

By Christopher J. Bise

The objectives for the research project, "Coal Mine Injury Analysis: A Model for Reduction Through Training," were to identify and develop a means to indicate deficiences in human performance, job skills, and/or knowledge at a given mine site that are amenable to alleviation through training or job redesign, and to provide ;I set of analytical tools and training resources that will enable mine training personnel to effectively incorporate the noted deficiencies into a personalized model training program. The findings of this research project are contained in Light separate volumes. Volume I represents the Executive Summary of the study and provides a broad overview of the project's individual areas of emphasis and deliverables. The additional eight volumes provide greater detail on the development of a Model Mine Training Program based upon Professional Database Analysis, Incident Reporting, Loss Control, Job Safety Analysis, Risk Assessment, Cost/Benefit Analysis, and Mine Safety Management.

Jan 1, 1993

By S. L. Windes

"INTRODUCTION For a number of years the bureau of Mines has been engaged in the detection, recording and interpretation of earth- and air-transmitted disturbances, man-made and natural, related to mining operations. For the measure¬ment of such disturbances, special equipment was developed (1, 2, 3, 4, 8) 3/ and results of the measurements have been reported (5, 6; 7,9).In general, the ranges of amplitude end frequency of vibration encountered and recorded in the earth-transmitted disturbances were 0.00005 to 0.1 inch and 5 to 5,000 cycles per second; in the air-transmitted disturbances, pressures ranging from 0.001 to 100 pounds per square inch and 0 to 20,000 cycles per second were recorded.One characteristic of the earlier tests was that either the arrival time of the disturbance to be recorded was predictable or the recording speed was slow enough so that the record covered extended periods of time (for example, 4 hours). As the investigations continued, it became apparent that a recording device was required that would respond to transient vibrations arriving at indeterminate times and at the same time provide a permanent record of displacement or acceleration versus time on a scale that would permit the analysis of waves having frequency components up to 10,000 cycles per second. A film or paper speed of 720 inches per second was found to be adequate, as this provides approximately 3/4 inch of record for each 0.001 second."

Dec 1, 1947

By M. H. Kline, Wing G. Agnew

"INTRODUCTION The Yancey-Crawford tract, located 1-1/2 nines east of Yancey station on the Norfolk & Western Railway in Rockingham County, Va. was from 1917 to 1941 considered an unusually promising manganese prospect. Because of the favorable geologic formations and because of the common occurrence of manganese in the district and Virginia's large production of these minerals from this area, geological report 3/ have listed this tract as the No. 1 prospect in the State. During World War I, extensive geologic studies were made to locate manganese deposits similar to those exploited at the Crimera mine near Waynesboro to alleviate this mineral shortage during the existing emergency.In September 1941 the Bureau of Mines started exploratory drilling on the tract in an effort to discover and block out reserves of manganese minerals as authorized by the 76th Congress under the Strategic Materials Act. After five drill holes wore sunk, the project was terminated October 1941."

Apr 1, 1948

By T. Ruff

Researchers at the National Institute for Occupational Safety and Health, Spokane Research Laboratory, studied technology and methods that could reduce accidents involving surface mining equipment that collides with other vehicles or workers, or drives over an unseen road edge. These accidents are partially attributed to the lack of full visibility around these large pieces of equipment. Blind areas can be extensive and this report presents plots of blind areas for five pieces of surface mining equipment. Several technologies designed for detecting obstacles in blind areas and providing a warning to the operator were evaluated on off-highway dump trucks. These proximity warning systems included radar, sonar, GPS, radio transceiver tags, and combinations of radar and cameras. A summary of test results is presented in this report, along with guidance on effective proximity warning technology, installation and maintenance considerations, and recommendations for effective implementation. This study found several commercially available systems that could effectively warn an equipment operator of an impending collision. Several new technologies also show promise for reducing these accidents. In most applications, it is recommended that sensor-based systems be combined with video cameras to provide important alarming functions along with an actual view of the blind area.

Jan 6, 2007

By John Owens, Marc Endicott, Hamid Maleki

This study presents a historic overview of the role of mobile roof support (MRS) technologies in improving stability and worker safety and presents the results of recent field evaluations of the MRS load rate monitoring device and other remote deformation-monitoring techniques. Field studies were implemented at two sites in cooperation among researchers from the National Institute for Occupational Safety and Health (NIOSH), Maleki Technologies, Inc., and J. H. Fletcher & Co. The objective of the field programs were to (1) study the interaction between MRS’s and coal mine strata and (2) develop and test suitable monitoring systems for assessing roof and pillar stability. An MRS consists of a roof canopy, four hydraulic cylinders, a caving shield canopy, and associated electromechanical systems mounted on crawler tracks. The machines are controlled by radio from a remote location and operate on self-contained power units. Typically, MRS’s have capacities of 5,340 and 7,120 kN (600 and800 tons). In comparison to posts, an MRS is capable of maintaining the yield load after significant amounts of roof-floor deformation. Because the mining cycle is accelerated, MRS’s help reduce the potential for time-dependent roof falls. MRS performance has been monitored in the laboratory under controlled static loading conditions and in the field under deep, two-seam mining conditions. Laboratory studies have quantified support capacity and system stiffness as a function of machine height. Field investigations have focused on determination of optimum operating conditions and development of warning systems that indicate excessive load on the machine and/or impending roof-pillar stability problems. Analyses of field data show that roof instabilities are influenced by (1) pillar failure, (2) pillar yielding, (3) mine seismicity, (4)geologic structures, and (5) panel layout designs and mining practice.Pillar yielding and failure (unloading) and seismicity can be conveniently monitored by the load rate monitoring device, but for consistent detection of roof falls, additional deformation measurements directly within the cuts are needed.

By Richard J. Mainiero, Marcia L. Harris

The New York State Department of Transportation recently commenced highway widening and drainage improvement projects in Clarence and Amherst, NY. Drainage improvements including the installation of storm sewer lines required excavation to a depth of 2.5 m (8.2 ft). In September 2002, NYSDOT stopped further blasting when 800 ppm CO was detected in the basement of a house near the blasting site. At the insistence of NYSDOT, the general contractor developed a new blast plan with the assistance of an environmental consultant. The plan provided for the installation of multi-gas monitors in buildings of special concern and/or with basements and residential type CO monitors in all other buildings within 100m (330 ft) of the blast. The multi-gas monitors would be remotely monitored. The plan provided action levels which would ensure public safety. The blast design was also modified to allow for better venting of CO. Blasts were limited to 20 ft lengths. The overburden was to be removed from the rock and blasting mats put in place to prevent flyrock. Approximately twenty feet of trench adjacent to the blast was left open to allow ground movement and gas release. The use of CO monitors was effective to alert occupants of a building to the presence of CO. The most effective appeared to be the residential type CO alarms with digital readouts. They were simple and easy to use and allowed the public to participate in the process. False alarms were repeatedly received with the more sophisticated instrumentation. Residential type CO monitors are preferable to warn people near blast sites. More sophisticated instrumentation should be avoided unless personnel are experienced in its use. A general overview of the blasting and monitoring is presented and discussed. The use and effectiveness of residential type CO monitors and multi-gas monitors are discussed.

Because surface mining removes the original plant cover from the land and exposes the soil, special care is needed. Until the mined land is stabilized by revegetation, snowmelt and rainfall can pick up sediment and erode mined lands much faster than undisturbed areas. Sediment control is an important aspect of protecting the environment during mining and reclamation because without it, large amounts of sediment can clog streams, increase the risk of flooding, damage irrigation systems, harm aquatic habitat, and limit the use of water for other purposes. Stream quality can be affected many miles downstream from the mine. Before SMCRA was implemented many streams were degraded by uncontrolled sediment from mining. Sediment is controlled through careful planning and a design that incorporates a variety of measures that work together to reduce soil erosion at the mine. Disturbed areas are graded, and some areas terraced, to achieve stable slopes, reduce runoff water velocity, increase infiltration, and divert runoff into drainage channels so that it flows away from unvegetated, erodible areas. Grading along the slope contour and scarify in gun vegetated slopes with bulldozer track marks help prevent erosion by slowing down the flow of water. Runoff from haul roads is controlled by culverts and roadside ditches. Sedimentation ponds or other forms of sediment control are required at all mines to minimize the amount of sediment leaving the site.

Jan 1, 1992

By Stephen A. Swan

Bureau of Mines researchers have collected and evaluated rollover protective structures (ROPS) f or more than 10 yr. ROPS and falling object protective structures (FOPS) are required on specified mining machines under regulations of the Mine Health and Safety Administration (MSHA). Both ROPS and FOPS are required on mining machines used in surface coal mines and surface areas of underground coal mines (30 CFR 77.403 and 7 7.4 13a), and ROPS are required on mining machines used in metal and nonmetal mining operations (30 CFR 55, 56, and 57.9-88). This illustrated manual provides mine safety personnel, MSHA inspectors, and original-equipment manufacturers with guidelines and a check- list for inspecting ROPS being used in the field. The manual discusses specific requirements of the MSHA regulations and minimum inspection and maintenance checks for ensuring compliance with those regulations. An easily reproducible checklist is provided as an aid to the inspection of ROPS.

Jan 1, 1985

By Donald F. Reed

In its investigation of old, abandoned, lead-zinc mines at which records of operations are not available, in 1914 the Bureau of Mines dug surface trenches anti', in 1947 It diamond-drilled three holes at the Albright Farm deposit in Sinking Valley. Some good lead-zinc ore had been extracted from veins in dolomitic limestone during the time of the American Revolution and as late as 1870. Since that time the only activity was sporadic prospecting and developing. Thu Bureau of Mines disclosed two additional veins by surface trenching, but diamond drilling failed to find significant lead-zinc mineralization.

Jan 1, 1949

By N. F. Le Jeuns

For a number of years the Bureau of Mines has conducted semi-annual surveys to determine the changes in motor gasoline being sold in the United States. It was pointed out in the previous survey that there was an apparent tendency toward greater uniformity in the character of gasoline marketed in the United States. This practically uniform tendency which continued from April, 1917 to January, 1923, has been interrupted in the, present survey, as shown by an examination of the column marked "Difference," as given in Table 1. The figures in this table were obtained by averaging the end points of the least volatile and most volatile samples of gasoline. For example, of 850 samples analyzed in 1919, the 10% ,(85 samples) having the highest end points and the 10% having the lowest end points mere grouped, and the end points of each group averaged. These averages are represented in the table as the "Maximum 10%" and the ?Minimum 10%? respectively. The same process was used on the other surveys.

Jan 1, 1923

By J. Wade Watkins

One potential peaceful application of nuclear explosives is stimulating the production of liquid or gaseous hydrocarbons from essentially nonproductive deposits of petroleum, natural gas, oil shale, and tar sands. Within the United States the appreciable difference between producible proved reserves and ultimate reserves and resources of hydrocarbon deposits is of such magnitude that much petroleum, natural gas, shale oil, and bitumen will not be produced unless significant technological progress is made in production techniques. The shattering effect of contained nuclear explosives and, to a lesser extent, the heat produced, have been considered as stimulative forces when the thickness, depth, and nature of such deposits permit considering the use of nuclear devices. Mechanical production problems would be less in an oil or gas reservoir than in an oil-shale or tar-sands deposit. Also, tar-sands resources in the United States may not be adequate to warrant serious consideration of applying nuclear-explosives stimulation. Gas reservoirs should present the least-radioactive-contamination problem. The technical feasibility of using nuclear explosives cannot be evaluated fully at present. Additional information is needed on the effects of pressure, heat, and radioactivity on the solids and fluids of hydrocarbon deposits, the nature and extent of induced fractures in different rock media, and the possibility of isolating and confining or removing radioactive contaminants. Final technical feasibility can only be determined by a field test. If technical feasibility is established, economic feasibility will depend upon the comparative cost of producing hydrocarbons by nuclear explosives and by conventional means. It is probable that an economic comparison would favor nuclear stimulation only where devices of relatively high yield could be used practicably and safely.

Jan 1, 1964

By L. J. Prosser, G. Esterhuizen, A. T. Iannacchione

The potential for roof fails in underground mines remains a clear and present danger for mine workers An investigation of ground conditions in nearly 50 percent of the nation’s underground stone mines fold that the slate of roof stability is primarily determined in a limited and subjective manner. These large-opening mines with roof heights typically 7 m (23 ft) or more, make physical observation difficult. Although some mines use monitoring techniques to gain additional information an roof stability, this practice is usually short term and localized to address ground conditions in a particular section or part of the mine. A roof-fall hazard-assessment techniques was development based on engineering judgment acquired from extensive underground stone mine experience and on exanimation of the related literature. This technique utilizes observational processes to determine roof fall likelihood Case-study scenarios offer a realistic picture of model implementation. Providing the mine level decision-maker with an accurate assessment tool to ascertain the level of ground fall hazards is expected to reduce mint worker injuries and fatalities Moreover; the presences of danger can be overcome with a clear picture of quantified ground conditions.

By B. J. Dalton

This report gives general expressions for evaluating various thermo-dynamic properties applicable to a two-component system, including liquid-vapor equilibria. In addition, expressions are developed for some of the quantities useful in making thermodynamic consistency checks on phase equilibria data. These formulas were developed from the general principles of thermodynamics and are expressed in terms of the compressibility factor, which is assumed to be an explicit function of the molal density, the absolute thermodynamic temperature, and the composition.

Jan 1, 1968

By John Taber, Robert D. O'Brien

"INTRODUCTION The Bozeman corundum deposit was first examined in May 1944 by an engineer of the Bureau of Mines. In August 1944, the property was re-examined because of a sharply increased war demand for corundum. A small program of trench exploring was undertaken after the second examination. The work was started in October 1944 and was completed in December 1944. This report presents the essential data obtained by the exploratory work.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that, they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploration work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests.The field work on the Bear Trap project was supervised by E. W. Newman, district engineer Montana District office. The microscopic examinations and. the grid grain-count analyses of the samples and the beneficiation tests were made at the Bureau's laboratory at Salt Lake City, Utah, under the direction of S. R. Zimmerley, chief, Salt Lake City Division, Metallurgical Branch."

May 1, 1947

By J. Wade Watkins

One potential peaceful application of nuclear explosives is stimulating the production of liquid or gaseous hydrocarbons from essentially nonproductive deposits of petroleum, natural gas, oil shale, and tar sands. Within the United States the appreciable difference between producible proved reserves and ultimate reserves and resources of hydrocarbon deposits is of such magnitude that much petroleum, natural gas, shale oil, and bitumen will not be produced unless significant technological progress is made in production techniques. The shattering effect of contained nuclear explosives and, to a lesser extent, the heat produced, have been considered as stimulative forces when the thickness, depth, and nature of such deposits permit considering the use of nuclear devices. Mechanical production problems would be less in an oil or gas reservoir than in an oil-shale or tar-sands deposit. Also, tar-sands resources in the United States may not be adequate to warrant serious consideration of applying nuclear-explosives stimulation. Gas reservoirs should present the least- radioactive-contamination problem. The technical feasibility of using nuclear explosives cannot be evaluated fully at present. Additional information is needed on the effects of pressure, heat, and radioactivity on the solids and fluids of hydrocarbon deposits, the nature and extent of induced fractures in different rock media, and the possibility of isolating and confining or removing radioactive contaminants. Final technical feasibility can only be determined by a field test. If technical feasibility is established, economic feasibility will depend upon the comparative cost of producing hydrocarbons by nuclear explosives and by conventional means. It is probable that an economic comparison would favor nuclear stimulation only where devices of relatively high yield could be used practicably and safely.

Jan 1, 1964