Search Documents

By Gwendolyn D. Hood

The U.S. Bureau of Mines developed a dewatering technique for treating wastewater that was tested on waste slurry from a commercial tile company in Alabama. Raw wastewater samples were pretreated with 10 Ib calcium chloride and 10 lb Wyoming bentonite per 1,000 gal of slurry. After pretreatment, polyethylene oxide (PEO) at dosages varying from 0.05 to 0.20 lb per 1,000 gal was mixed with the waste slurry, forming strong, tough floes that were separated from the clarified water using a trammel. The flocculated slurry was dewatered to a consistency that could be handled for subsequent disposal in a landfill. The clarified water quality was equivalent to that of the company's present treatment system.

Jan 1, 2010

By James S. Browning

The purpose of this investigation was to develop a dependable and economic method for recovering spodumene and mica from pegmatites of the type found in Gaston County, N. C. Laboratory batch tests and continuous flotation tests were made by the Federal Bureau of Mines to determine the feasibility of treating the ore by flotation to recover high-grade spodumene and mica concentrates. The spodumene flotation circuit yielded concentrates containing 6.50 percent lithia (Li20), with an overall recovery of 81.8 percent of the lithia in the ore, The mica circuit yielded concentrates containing 97.5 percent mica, with a recovery of 82.5 percent of the mica in the spodumene tailing.

Jan 1, 1961

By Miles B. Royer

The experimental blast furnace has attracted increasing interest during the past decade as a practical means for investigating a broad range of blast-furnace smelting problems. Under experimental-furnace conditions, information can be obtained with less expenditure of time and raw materials and, therefore, at lower cost than comparable information could be obtained under industrial operating conditions. Furthermore, the experimental furnace may be operated beyond the range of smooth operation, even to failure, to delineate the limits of operability. Such deviation from normal operating practice would be economically intolerable in industrial operations where production and operating stability might be disrupted. The Federal Bureau of Mines experimental blast furnace at Bruceton, Pa., near Pittsburgh, has been operated and under development since 1951. However, the usefulness of this experimental data to industrial practice was somewhat nebulous in early experiments, and the correlation of the experimental blast furnace with the industrial blast furnace was not known.

Jan 1, 1961

By Hugo E. Camargo

In an effort to reduce Noise Induced Hearing Loss (NIHL) in the mining industry, the National Institute for Occupational Safety and Health (NIOSH) is conducting research to develop noise controls for mining equipment whose operators exceed the Permissible Exposure Level (PEL). The process involves three steps: 1) Noise source identification (NSI), 2) development of noise controls, and 3) evaluation of the developed noise controls. For the first and third steps, microphone phased array measurements are typically conducted and data are processed using the conventional beamforming (CB) algorithm. However, due to the size and complexity of the machines, this task is not straight forward. Furthermore, because of the low frequency range of interest, i.e., 200 Hz to 1000 Hz, results obtained using CB may show poor resolution issues which result in inaccuracy in the noise source location. To overcome this resolution issue, two alternative approaches are explored in this paper, namely the CLEAN-SC algorithm and a variarion of an adaptive beamforming algorithm known as Robust Capon Beamformer (RCB). These algorithms were used along with the CB algorithm to process data collected from a horizontal Vibrating Screen (VS) machine used in coal preparation plants. Results with the array in the overhead position showed that despite the use of a large array, i.e., 3.5-meter diameter, the acoustic maps obtained using CB showed "hot spots" that covered various components, i.e., the screen deck, the side walls, the I-beam, the eccentric mechanisms, and the electric motor. Thus, it was not possible to identify which component was the dominant contributor to the sound radiated by the machine. The acoustic maps obtained using the RCB algorithm showed smaller "hot" spots that in general covered only one or two components. Nevertheless, the most dramatic reduction in "hot" spot size was obtained using the CLEAN-SC algorithm. This algorithm yielded acoustic maps with small and well localized "hot" spots that pinpointed dominant noise sources. However, because the CLEAN-SC algorithm yields small and localized "hot" spots, extra care needs to be used when aligning the acoustic maps with the actual pictures of the machine. In conclusion, use of the RCB and the CLEAN-SC algorithms in the low frequency range of interest helped pinpoint dominant noise sources which otherwise would be very hard to identify.

Jan 1, 2009

By James V. Kelly

During the spring and summer of 1947, the Bureau of Mines conducted an investigation and core-drilling program in the vicinity of the Rodham mine, approximately 4 miles north of Shullsburg, Wis. This work was undertaken as a part of a general study of the zinc and lead-producing area of southwestern Wisconsin. Work in the Rodham-mine area was done to investigate further a mineralized area frilled in part by the Puritan Exploration Co., a Delaware corporation, with offices in Galena, Ill. Some significant lead-bearing samples were obtained, but no continuous ore body was disclosed as a result of the Bureau of Mines work.

Jan 1, 1949

By Charlie Wyche

Principal mineral products in the Dominion of Fiji were gold, silver, pit and quarry construction materials, and cement. In the years 1978-79, the combined total value of these commodities accounted for some $15 million,2 or 85% of the total mineral output. Production of cement, sand and gravel, and quarry products increased substantially, but gold and silver output from Fiji's only operating metal mine continued the down-ward trend of recent years. Mineral exploration by several international mining companies as well as by local prospectors was being carried out over much of Fiji, and a number of interesting prospects were discovered. One of these, a medium-size porphyry-copper prospect in the Namosi area of Viti Levu, W88 at a mining feasibility study stage. At Mount Kasi on Vanua Levu, an extensive program of geological sampling and mapping W88 being conducted, and surface sampling and drilling W88 taking place at some base metal prospects in the south-central parts of Viti Levu. Also, high gold values in surface samples were reported at Vuda in western Viti Levu.

Jan 1, 1981

By Martin S. Oudenhoven

This Bureau of Mines report presents the results of a microseismic study conducted in the Climax block cave mine at Climax, Colo. Rock noises created by caving were monitored and their sources located during a 3-month period. A planar array of seven accelerometers, located above the block of ore being caved, detected the rock noise. A computer was used to calculate the location of the microseismic activity, using a traveltime difference method. The accuracy of these locations was estimated to be ±20 feet. An analysis of the data taken during the recording period showed a concentration of microseismic events located in the wall of the cave panel. This concentration of events was found to occur in a "high-silica" geologic forma-tion that cut across the caving panel approximately 200 feet behind the undercut.

Jan 1, 1973

By R. E. Lindstrom

Electrooxidation techniques were investigated on a bench scale by the Bureau of Mines to determine the applicability of the process for extracting molybdenum and rhenium from low-grade molybdenite concentrates. Parameters affecting the extraction, such as pulp density, power consumption, reagent requirements for pH control, and electrolytic cell configuration, were studied. Molybdenum and rhenium extractions of 98 to 99 percent were achieved from several concentrates containing 4.76 to 28.6 percent molybdenum and 180 ppm to 1,000 ppm rhenium. Optimum results were obtained by maintaining pH values between 5.5 and 7.0 during electrolysis and allowing the final pH to rise to about 8.2. Reagent consumption was 4 to 6 pounds of sodium carbonate per pound of molybdenum extracted. The power consumption declined from a range of 12 to 25 kilowatt hours per pound of molybdenum extracted with immersion electrodes to 9.7 kilowatt hours with a bipolar flow-through cell; however, molybdenum extraction was independent of cell configuration.

Jan 1, 1973

By B. J. Scheiner

The Federal Bureau of Mines investigated an electrolytic oxidation procedure for extracting lead, zinc, copper, and silver from lead-zinc concentrates. Concentrates slurried in brine were pumped through the anode compartment of electrolytic cells equipped with selective ion diaphragms. Hydrochloric and hypochlorous acids generated in the anode compartment converted the metal sulfides in the concentrates to soluble metal chlorides, sulfate ion, and elemental sulfur. Metal extractions of 92 to 100 pct were obtained from lead-zinc concentrates at an energy consumption ranging from 1.5 to 5.0 kW-hr/lb metal extracted. Sodium hydroxide was formed in the cathode compartment at a current efficiency of >99 pet. Silver and copper were extracted from refractory tetrahedrite minerals, but the process entailed a relatively high energy consumption. Sealing the top of the diaphragm cell utilized the chlorine more effectively, thereby reducing energy consumption 10 to 50 pct.

Jan 1, 1975

By R. R. Wells

This report summarizes the results of laboratory testing of copper-bearing magnetite ore from the Poorman, Bush & Brown, and Copper Center deposits, Kasaan Peninsula, Prince of Wales Island, southeastern Alaska. The ores contain minor amounts of chalcopyrite and pyrite. Intimate association of these sulfides with magnetite necessitates fine grinding for adequate liberation and rejection of copper and sulfur and for the production of high-grade iron concentrate low in objectionable impurities. Laboratory tests indicated that the optimum results can be obtained by flotation of ore ground to minus-100-mesh, with subsequent wet magnetic separation treatment of the flotation tailing. A summary of results obtained by this treatment of the three samples tested is shown in table 1.

Jan 1, 1957

By J. E. Tress

The Bureau of Mines has developed a process to utilize waste heat from electric arc steelmaking furnace gases to preheat the ferrous material charged to the furnace. Four heat exchangers were designed, tested, and operated successfully on 1-ton electric arc furnaces. Briquets and pellets were charged continuously, both countercurrent to the hot furnace offgasses and at ambient temperatures. A comparison of the electrical energy consumed in each situation showed that preheating can lower energy requirements as much as 15.6 percent.

Jan 1, 1975

By Maria I. De Rosa

The U.S. Bureau of Mines conducted experiments for predicting materials' ease of combustion (smoldering onset, smoldering, flaming, and decomposition rates) by means of submicrometer smoke particle characteristics for the development of a simple test method. The experiments were carried out in an approximately 20-L furnace, with a 10-L/min airflow through the furnace for a 14-min duration, at set furnace temperatures of 150°, 250°, and 1,000° C. The variables studied as a function of time were the onset time of smoke particles, time and duration of maximum smoke particle generation, average concentration of smoke particles, and particles' average diameter, mass weight loss, and furnace temperatures. Results show that the onset time of smoke particles is predictive of materials' ease of smoldering, and the time of maximum smoke particle generation and its duration, coupled with mass weight loss, are predictive of materials' ease of smoldering and flaming (depending on the experimental temperatures), and decomposition rates.

Jan 1, 2010

By M. S. Seehra, V. S. Babu

"INTRODUCTION The accurate determination of the free silica index in coal mine dusts is an important requirement because severe health hazards are believed to be associated with the inhalation of respirable-sized silica particles.1-6 Free silica refers to the three polymorphs of silica (Si02)viz., quartz, cristobalite, and tridymite-although quartz is usually the dominant form in most mine dusts.6 The free silica index is the concentration in micrograms of free silica in air per m3 of air sampled corrected to standard conditions of 25°C and 760 mm/Hg, the present MSHA (Mine Safety and Health Administration) limit on time-averaged basis being 100 µ.g/m 3 for coal mines. A recent review7 has concluded that quartz, cristobalite, and tridymite particles impart nearly equal long-term hemolytic damage when compared on a per unit surface area basis.At present, two experimental methods-viz., transmission infrared spectroscopy (TIRS) and x-ray diffraction (XRD)-are commonly used for the determination of silica concentrations in mine dusts. In TIRS, which has been adopted by MSHA and is commonly called the P7 method, the silica absorption band near 800 cm - 1 is used for quantification. However the mineral kaolinite, which is commonly present in mine dusts, also has absorption band, albeit weaker, at 800 cm- 1• To correct for this interference, one uses the stronger 915-cm -1 band of kaolinite to determine the concentration of kaolinite, and the kaolinite contribution to the absorbance at 800 cm-1 is then determined from a calibration curve, leading to the determination of silica by subtraction. In the XRD technique, usually an internal standard such as CaF 2 is used to determine the concentration of silica from line intensity measurements. XRD has the added advantage that concentrations of quartz, cristobalite, and tridymite can be determined.8•9 In an exhaustive study on the precision of the techniques ofTIRS and XRD for monitoring worker exposure,9 the conclusion has been reached that both methods measure silica within 253 of the ""true"" value 953 of the time in a single laboratory."

Nov 1, 1995

By H. J. Heinen

The Bureau of Mines, investigated a cyanidation-carbon adsorption technique for extracting gold from arsenopyrite concentrates. Agitation leach experiments were conducted on 85-pct-minus-35-mesh gravity concentrates containing 21.8 oz gold and 6.4 oz silver per ton. Results obtained in leaching the concentrates showed that 96.9 pct gold and 90.7 pct silver extraction could be achieved in 96 hours of agitation. Gold and silver were recovered from the resulting pregnant solution by exposure to granular activated carbon in a countercurrent system. Carbon loadings of 2,556 oz of gold and 502 oz of silver per ton were achieved. These loadings are significantly higher than heretofore thought practical.

Jan 1, 1980

By X. Shi, V. Vallyathan, N. S. Dalai

"Using. ESR spin trapping methodology, evidence was obtained that fresh quartz dust in a cell-free aqueous medium generated hydroxyl - and possibly superoxide radicals. The hydroxyl radical generation potential decreases on storing of fresh quartz dust in ambient air and on the addition of either catalase, superoxide dismutase, desferoxamine, or DMSO. The role of quartz related radicals in the biochemical mechanism of acute silicosis is suggested from these findings.IntroductionThis report summarizes our electron spin resonance (ESR) detection of oxygenated radical formation by freshly crushed quartz particles in a cell-free aqueous medium, and its inihibition by radical scavengers. This study was undertaken with to elucidate the primary biochemical mechanism involved in the development of silicosis (Farber, 1983; Reiser and Last, 1979; Silicosis and Silicate Disease Committee, 1988). In particular the mechanism by which the quartz particles exert their toxic action on cells and the process(es) by which these actions progress to fibrogenesis are still not well understood (Farber. 1983; Reiser and Last, 1979;). It is generally believed that the action of quartz particles on the cell membrane is the starting point of the silicotic process (Farber, 1983; Parazzi et al., 1968). Thus the surface characteristics of the quartz particles have been the subject of several recent studies (Bolls et al.. 1983; Dalai et al., 1986; Fubini et al., 1987). Recently, We reported that mechanical crushing of quartz under normal atmosphere generates free radicals which decay with time, and that these free radicals are associated with a higher cytotoxicity of fresh quartz dust as compared to aged dust from the same stock (Dalai et al., 1986; Vallyathan et al.. 1988). The formation of Si• and. SiO--type of radicals from quartz particles crushed under atmospheric conditions has also been reported by Fubini et al. (1987). In addition, Gulumian and van Wyk (1987) have reported that quartz particles react with hydrogen peroxide (H202) to generates hydroxyl radicals (•OH) and suggested that this process might contribute to quartz's pathogenicity. However, these authors did not report the effects of metal chelators, so it was not clear as to whether the detected -OH radicals simply resulted from the Fenton reaction involving exogenous metal ion contaminants. Earlier, Marasas and Harington (1960) reported that quartz particles could function as an oxidant in a number of in vitro oxidations, including the hydroxylation of proline and lysine. They postulated that silica dusts, on reacting with water, could release H2O2 which might have the potential to react with various biological constituents and thus cause tissue damage. In fact, Gabor and coworkers (Gabor and Anca, 1974; Gabor et al., 1975) suggested that the cytotoxicity of quartz particles might be associated with the generation of some 'factor or factors possessing the properties of a free radicals capable of promoting the peroxidative chain cleavage of polyunsaturated fatty acid moieties of the phospholipids in the cell membrane. More recently Weitzman and Graceffa (1984) reported that asbestos is able to catalyze the generation of • OH radicals from H2O2. Their later work indicated that lipid peroxidation may be one of the mechanism by which asbestos produces tissue injury (Weitzman and Weitberg, 1985). This is significant because • OH radicals are capable of causing peroxidation by abstracting hydrogen atoms from cell-membrane lipids and initiating lipid peroxidation in lysosomal membrane (Fong et al., 1973). In fact, the formation of oxygenated species in reactions involving quartz was suspected since Kolbanev et al. (1980) reported the detection of H2O2 in the reaction of fresh quartz particle with aqueous medium. The present work was thus undertaken to detect the anticipated formation of some oxygenated, radical species by reactions of quartz in a cell-free media and its inhibition by radical"

Jan 1, 1988

By Arne Landsberg

The Bureau of Mines has undertaken research to elucidate the chemistry involved in the efficient recovery and control of minor elements in base metal smelting operations. These elements should be effectively recovered not only because they have commercial value, but also because of their potential hazard to workers' health and the environment, if they are not controlled during processing. Cadmium, a minor metal in zinc ores, is the subject of this report. The roasting step of the complex zinc-smelting process was chosen for investigation because of the high potential for removing cadmium by volatilization during this primary stage. Commercial roaster feed materials were used to determine the sequence of reactions and the effect of these reactions on the volatilization of cadmium. Electron microprobe examination of both the commercial roaster product and oxidized sulfide solid solutions prepared in the laboratory showed that oxidized iron was of prime importance in preventing cadmium volatilization. The mechanism by which iron prevents cadmium volatilization is proposed, and a preheating technique is recommended for more effectively recovering cadmium prior to roasting.

Jan 1, 1981

By R. V. Ramani, R. A. Jankowski, R. Bhaskar

"The spatial distribution of airborne dusts, deposition of dust in the airway, as well as the effect of airflow velocity and particle density on dust behavior in mine airways were studied in a set of experiments performed in a mine airway under controlled conditions. Considerable deposition of dust near the source was indicated. Pronounced effects due to velocity were observed in ambient dust concentration and deposition along the mine airway, both in the respirable and the total size ranges. Cross-sectional concentration measurements indicate an increase in concentration from the roof to the floor. The average cross-sectional concentration is about 75% of the concentration in the center of the airway.IntroductionA number of studies have been performed since the early 1950s on the behavior of dust in mine air (Bradshaw and Godbert, 1954; Dawes and Slack, 1954; Bradshaw et al., 1954; Hall, 1955-56; Reinhardt, 1971; Ford, 1971; Courtney et al., 1982). While the experimental data available from these studies are indeed useful in understanding dust cloud behavior in a specific situation, no generalized conclusions can be drawn because of the lack of data on parameters such as flow velocity, size distribution of the source dust, and particle density. These change from mine to mine or even within the same mine. The present study is aimed at providing a better understanding of the temporal and spatial behavior of dust particles in underground' mine airways (National Academy of Sciences, 1980). The characteristics studied encompassed airborne concentrations and floor depositions over the entire size range as well as the respirable size range. The experimental results in this paper are intended to complement a mathematical model developed to predict ambient concentration and deposition of airborne dust in mine airways (Bhaskar and Ramani, 1986)."

Aug 31, 1989

By Edward D. Thimons

Because of the high number of accidental methane gas ignitions in metal and nonmetal mines, the Bureau of Mines searched for a simple guideline that would allow mine personnel to evaluate the methane hazard in a given mine. Air samples were collected by the Bureau in 53 metal and nonmetal mines and analyzed for trace evidence of methane gas. Samples were collected in the returns and at the working faces. Those mines classified as gassy by the Mine Safety and Health Administration had a significantly higher average methane concentration than those classified as nongassy. Of the 9 gassy mines sampled, 7 had methane concentrations above 100 ppm, whereas only 1 of the 44 nongassy mines had a concentration above 100 ppm. The 100-ppm concentration may be used as a simple and convenient guideline for forecasting the methane hazard in a mine, whether or not the mine is classified as gassy. There was no consistent correlation between commodity mined and methane concentration, nor was there a correlation between mine depth and methane concentration. Neither of these factors can be considered a guideline for predicting methane hazards.

Jan 1, 1979

By R. L. Grant

The conventional gallery test used by the Bureau of Mines Explosives Testing Station and corresponding establishments in other countries to establish the permissibility of explosives serves principally to differentiate the relatively safe explosive from the positively unsafe one. It has been recognized for many years that a more definitive test is needed to measure the relative incendivity to firedamp of explosives and explosive devices. A new method - the oxygen-value test - for measuring this incendivlty quantitatively has been devised and is being tested at Bruceton, Pa. To date, this testing bas been limited mainly to straight nitroglycerin dynamites. It is planned to study application of the method to permissible explosives in the near future. These results will be reported later. In the present report, permissible explosives will not be considered specifically.

Jan 1, 1954

By T. A. Henrie, E. K. Kleespies

Electrolytic studies were conducted to determine the transfer rates of the alloying constituents from molten titanium anodes to solid titanium cathodes in molten salt systems . The metals , nickel , tin , copper , bismuth , and manganese , were selected on the basis of thermodynamic data and the melting point of the alloy system . The transfer of nickel , tin , and bismuth was very low . The content of these elements in the cathode was in the range of less than 0.01 to 0.001 percent . The copper transfer was 0.6 to 0.8 weight - percent in electrolytes containing titanium chlorides and 0.12 weight - percent in titanium fluoride salt systems . The manganese transferred at rates comparable to that of titanium . Highpurity titanium and titanium- manganese alloys of uniform composition were produced by electrorefining molten titanium alloys in chloride electrolytes . Comparisons are made between the calculated and the actual quantities of metal transfer .

Jan 1, 1964