Search Documents

By G. R. Hopkins

A recently completed survey , made by the Bureau of Mines to determine the trend of fuel consumption at refineries in the United States , showed the following outstanding points : A decrease in the use of oil for fuel in 1927 of over 5,000,000 barrels as compared with 1926 ; a decrease in the use of coal of over : 1,000,000 short tons ; small increases in the use of both natural gas and refinery gas ; an increase in the use of petroleum coke . The decrease in fuel - oil consumption was approximately 2,000,000 barrels each in the Atlantic Coast , Texas , and Louisiana- Arkansas districts , with an increase of 1,000,000 barrels in the Indiana - Illinois district , or a net decrease of 5,000,000 barrels . The decrease in fuel- oil consumption by refineries in the Texas and Louisiana- Arkansas areas was offset largely by increased consumption of natural gas and refinery gas , whereas the increased consumption in the Indiana- Illinois region was more than offset by the decrease in coal consumption . The use of coal for fuel declined from 6,052,000 short tons in 1926 to 5,031,000 short tons in 1927. Practically all of this decrease was recorded in the Appalachian and Indiana- Illinois districts , which at the same time showed the largest percentage increase in the use of oil for fuel . It is probable , therefore , that although coal prices also fell off , a considerable quantity of oil replaced coal in this area in 1927. In addition , the group of refineries , which are by location more or less definitely committed to the use of coal for fuel , undoubtedly succeeded in saving a material amount of coal through the use of more efficient fueling methods . A total of 130,815,000,000 cubic feet of natural gas was consumed for fuel at refineries in 1927. This represents an increase of 8 per cent over the 1926 total . Nearly all of this increase resulted from the opening of a line from the Monroe field to Baton Rouge , La . Had this line not been opened , there would have been a decrease in the use of natural gas , as a number of districts , particularly the Rocky Mountain , reported decreases in its use . The use of refinery or still gases for fuel did not change materially during 1927 , there being a total of 52,807,000,000 cubic feet burned as compared with 52,077,000,000 cubic feet in 1926. Refinery gases are largely a product of cracking and , it was probably more than a coincidence that a few districts in which cracking slowed down in 1927 also reported less refinery gas used as fuel .

Jun 1, 1924

By Peter J. Clarke

Development of the mineral and energy resources of Afghanistan appeared to be a top priority of the Soviet-controlled Government in the country. In the Afghan Government's plan for 1980-81, the largest allocation in the development budget was for mines, industry, and energy (46.7%). In contrast, only 23.1% of the budget was allocated for agricultural development, despite the fact that the great majority of the population was dependent on farming. The mineral industry of Afghanistan consisted of the production of natural gas, cement, coal, fertilizer materials, and rock salt. Production levels for all of these commodities were down an average of 45% from those of 1978, before the Soviet invasion. Prior to the invasion, small quantities of asbestos, barite, and talc had been produced along with about 6,000 to 7,000 kilograms per year of lapis lazuli, a semiprecious gem stone. Afghanistan had supplied about 80% of the world's output of lapis lazuli. Following direct Soviet intervention, production of these minerals declined to near zero.

Jan 1, 1983

By Steven G. Grannes

This U.S. Bureau of Mines report summarizes Federal mandatory belt conveyor automatic fire suppression system installation requirements and inspection procedures, identifies system failure modes observed during in-mine investigations, and suggests system design and maintenance upgrades which, if implemented, would result in an improvement in overall system reliability. This report is a compilation of recommendations based on discussions with Mine Safety and Health Administration (MSHA) inspectors, review of manufacturer's literature, discussions with mine personnel, and research investigations of automatic fire suppression system performance in the laboratory and in mines. The Code of Federal Regulations (CFR) requirements for installation, inspection, and maintenance of fire suppression systems should be regarded as minimum standards.

Jan 1, 1990

By David P. Conover

The U.S. Bureau of Mines (USBM) has developed a computer-assisted Ground Control Management System (GCMS) for near realtime evaluation of underground coal mine ground conditions. The GCMS combines existing mine-monitoring system and sensor technology with automated computer analysis techniques to enhance the acquisition, analysis, and display of geostructural data. The GCMS, which combines mine structure data with other information, such as geologic conditions and mine layout, has provided information on mining-induced stress transfer and pressure buildup associated with several ground control events. The GCMS collects and analyzes shield-leg pressure, ground pressure, and strata movement data to evaluate the structural behavior of an active Western U.S. Iongwall coal mine. Field data are transmitted over a dedicated phone line to the USBM Denver Research Center (DRC) mine monitoring laboratory, 240 km (150 miles) from the mine site. Real-time collection, processing, and analysis of mine structure and shield pressure information has proved to be an effective method for near-face ground conditions while mining progresses. The GCMS provides the mine operator with information to rapidly identify and manage potentially hazardous ground conditions while mining is in progress.

Jan 1, 1994

By Eugene T. Sheridan

The annual survey of the fuel-briquet industry by the Bureau of Mines, United States Department of the Interior, revealed that 21 fuel-briquet plants in 11 States were in operation and reported production in 1956. The demand for fuel briquets in the United States has gradually declined since 1948, and the number of operating plants has decreased from 36 to 21. Also, the annual productive capacity of the industry has decreased, although not a proportionate amount because most of the plants that were abandoned were small and in most instances had a designed capacity of less than 25,000 tons per year. In 1956 the 21 active plants had an annual capacity of 3.7 million tons (table 2), which was only 20 percent less than the total capacity of the 36 plants in 1948. This indicates that most of the larger plants have remained active, even though operating at reduced rates, and the average capacity of the industry has increased from 130,000 tons per plant in 1948 to 177,000 tons in 1956. Since 1948 operating rates have decreased from 67 percent to 41 percent of annual capacity.

Jan 1, 1958

By R. S. James, E. J. Gleim

Not long after electrically driven equipment was introduced into coal mines it became apparent that the spark-producing parts, such as controllers and motors, required safeguards to prevent the ignition of mine gas that might come into their vicinity. Many of the early designs attempted to provide protective enclosures having ventila¬tion and relief for pressures if ignition should occur within. The principal feature of the Davy safety lamp, namely, the wire gauze, was employed widely for this purpose. Other devices were developed to reduce the temperature of products of combustion escaping through the protected openings to a value below that which would cause ignition of surrounding explosive atmospheres. Although many such devices performed their intended function satisfactorily under laboratory conditions they were not so satisfac¬tory when subjected to the rigorous conditions encountered under¬ground. Corrosion, mishandling, and accumulations of grease and dirt reduced or destroyed their protective qualities after a period of service in the mines. In the United States this has led to abandon¬ment of special devices in favor of what is called " total enclosure " which means that no regular provision is made for ventilation and release of pressure but rather that the housings or enclosures are built strong enough to withstand the explosion pressures without rupture. As a further protection the joints usually are made of broad, closely fitting surfaces. It is impractical to make such joints absolutely gastight in ordinary machine practice when provision must be made for partial or complete disassembly to facilitate ad¬justments and repairs. Therefore, when an explosion occurs within such enclosures flames may escape through the joints. If the latter are broad enough and not separated too widely, however, the flames will be cooled by contact with the metal surfaces (flanges) of the joints, by rapid expansion, or by both cooling and expansion, with the result that an explosive atmosphere surrounding the enclosure will not be ignited. This is termed " flange protection." In testing parts of cutting machines and other equipment for coal mines, with the ultimate object of approving the equipment for use

Jan 1, 1935

By Ronald H. Church, Walter E. Pittman, J. T. McLendon

In its role of providing technical assistance to the mining industry, the Bureau of Mines' Tuscaloosa Research Center has conducted research to develop trapped miner location systems which would aid in locating miners trapped by underground mining disasters. Efforts to produce electromagnetic systems for the location of trapped miners underground and to communicate with them were surveyed, from the 1920's to 1981. Theoretical studies of through-the-earth electromagnetic transmissions are described as well as studies of the electrical characteristics of various rocks, minerals, and soil. Several trapped miner location systems are reviewed including the Westinghouse systems, the DEVELCO system, and an automated three-dimensional location system, and the phase difference of arrival technique. Tangential research, relevant to trapped miner location systems is described. A comprehensive bibliography covering all aspects of trapped miner, through-the-earth electromagnetic location and communications systems is appended.

By D. Bienstock

A rig was constructed to burn 100 to 125 lb of coal per hour at 4,000° F in a cyclone burner with oxygen-enriched air preheated to 1,500° F to ascertain the problems in the coal-fired MHD generation of power. Potassium carbonate was added to the coal at several concentrations up to 1.23 g-moles/kg of coal (17 lb K2C03/100 lb coal). Boiler-tube materials maintained at wall temperatures of 800° to 1,500° F were exposed to the combustion effluent of 1,800° to 2,500° F. Practically complete removal of sulfur dioxide from the stack gas was achieved with the seed addition. Nitric oxide formation followed theoretical expectations at combustion temperatures with some decomposition of the NO occurring as the gas cooled flowing through the system. Nitrates in the fly ash were less than 1.7 percent of the total fixed nitrogen. With aqueous extraction of the fly ash a maximum recovery of 75 percent of the potassium was obtained. Haynes 25 was unattacked at a wall temperature of 1,500° F in combustion gas at 2,500° F; the stainless steels 310, 316, and 446 were resist-ant at a metal temperature of 1,100° F in gas at 2,100° F.

Jan 1, 1970

By W. D. Haselton

This paper dealing with the mining methods used in producing iron ore from an underground operation located in the central-western part of the Mesabi Range in Minnesota is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts in the United States. The mine here discussed was laid out in accordance with a plan adapted to a rather unusual type of ore body, the nature of which is such that the mining method necessarily differs in certain respects from the method used at most of the mines in this district. A description of it may therefore be of interest.

Jan 1, 1930

By Robert F. Randolph, Dana C. Reinke, Richard L. Unger

Purpose The NIOSH Hearing Loss Simulator is a software training and communication tool for promoting hearing loss prevention. It allows a user or trainer to demonstrate the effects of noise exposure on hearing without experiencing an actual noise-induced hearing loss. Estimates of the effects of different levels of noise exposure are based on the American National Standard Determination of Occupational Noise Exposure and Estimation of Noise-Induced Hearing Impairment, otherwise known as ANSI S3.44. This standard specifies the predicted hearing loss for noise-exposed populations of individuals based on risk factors that include gender, age, sound levels (in A-weighted decibels or dBA), and years of exposure. Algorithms specified in the standard were derived from empirical studies of populations that had no exposure to loud noise and other populations that had experienced various levels and durations of noise exposure. This manual explains the major objectives that can be addressed with the simulator and training scenarios that can be applied to real-life, real-worker scenarios. The majority of this guide explains the simulator's functions in detail. Simulator users are encouraged to read this manual while learning how to run the software. [ ] Training Objectives The main objective of the Hearing Loss Simulator is to increase motivation for taking effective hearing prevention action by demonstrating simulated noise-induced hearing losses. [The Simulator can also help teach the following facts about hearing loss. Hearing loss is affected by noise levels. Hearing loss worsens as the noise exposure duration increases. Hearing loss can become permanent. Hearing loss makes it harder to hear what others say. Most hearing loss is not caused by age. Speech is made up of both low and high pitch sounds. Hearing loss due to noise makes it harder to hear high pitch sounds. Hearing loss due to noise has less of an effect on hearing low pitch sounds.]

Jan 3, 2008

By D. H. Zellers

Since its inception the United States Bureau of Mines has fostered the development of portable mine lamps. Although there is still much to be desired with respect to illumination in coal and metal mines and the replacement of open lights has been slow the Bureau has been given credit for assisting materially in the development and introduction of the safe and efficient portable mine-lighting equipment available today. Much of the work conducted by the electrical section of the Bureau entails approval tests of various types of electrical equipment, including lamps; to be used in atmospheres that may contain methane or coal dust in explosive proportion. If a can lamp meets the requirements-for safety, efficiency, and adequacy, as published in Schedule 6B,4 it is approved and is generally known as a "permissible" lamp. The terms "approved" and '"permissible' often are used interchangeably. The manufacturer must put an approval plate on each approved lamp, showing it has mot the schedule requirements. The approval plate is not a guarantee that the lamp is safe. However, if the lamp, once in service, has not had any parts changed or improperly assembled or if carts that wear out or depreciate have been properly replaced it should still, be safe, efficient, and adequate for the service intended. Virtually all electric cap lamps in service today in the United States and a great many that have been sent to foreign countries bear the approval plate of the United States Bureau of Mines. Although many explosions have been attributed to open lights none has been charged against the permissible cap lamp. Nystagmus, a disease of the eye attributed to working under insufficient illumination, is practically unknown among; American miners, although it is quite prevalent among European miners.

Jan 1, 1935

By A. W. Fahrenwald

As an aid to studies of grinding, a batch laboratory classifier and elutriator has been developed at the U. S. Bureau of Mines Metallurgical Field Office at Moscow, Idaho, in cooperation with the University of Idaho. It is designed for use in conjunction with other batch laboratory apparatus, such as ball mills and flotation machines. It is shown in Figure 1. Description and Operation of Batch Laboratory Classifier The classifying column is a cylinder 4 feet 2 inches long, of 5 3/4-inch inside diameter, and terminates at its top in a cone or funnel 18 inches in diameter at the overflow elevation. The pressure chamber is of the same diameter as the classifying column, and has a conical bottom; it is provided with two openings, one in the cylindrical portion through which water is admitted, and the other, a small drain hole, in the apex of the conical bottom. The two compartments are bolted together and communicate with each other through the medium of a constriction plate provided with 3/16-inch holes spaced 1/2 inch apart. Constriction plates having any other percentage of opening may be substituted as the needs demand water is admitted to the compartment below the constriction plate at constant pressure. The volume of eater admitted is controlled with a valve. It should be mentioned that the classifying column at the bottom, just above the constriction plate, is glass.

Jan 1, 1929

By Sidney Katell

Several systems have been proposed for the production of synthetic crude oil from oil shale. An economic analysis of one proposed system is presented in this paper. An oil shale complex to produce 100,000 barrels per calendar day of semirefined crude oil will require a capital investment of $426,216,400. This investment includes mining, retorting, intermediate pipelining, and partial refining. A selling price of $3.74 per barrel of product will be necessary to maintain a discounted cash-flow rate of 12 percent.

Jan 1, 1971

By N. S. Dalal, X. Shi

"This study reports a new property of the important NAD(P)H-dependent flavoenzymes, glutathione reductase, lipoyl dehydrogenase and ferredoxin- NADP oxidoreductase, that can catalyze a one electron reduction of metal ions such as chromium(VI) and vanadium(V). During the enzymatic reduction process, molecular oxygen is reduced to H2O 2 , which reacts with the reduced metal complexes to generate hydroxyl radicals. Since the hydroxyl radicals have been suggested to play an important role in Cr(VI) toxicity, this study provides a basis for a recent observation that Cr(VI) mutagenesis is strongly oxygen dependent. These results also point to an enzymatic pathway for the metabolism of some metal ions and concomitant generation of hydroxyl radicals. l. INTRODUCTIONThe purpose of this communication is to report that some important NAD(P)H-dependent flavoenzymes (glutathione reductase, lipoyl dehydrogenase and ferredoxin-NADP+ oxidoreductase) can catalyze one electron reduction of metal ions such as chromium(VI) and vanadium(V) and simultaneously reduce molecular oxygen to generate Hi02 and, eventually, the ""OH radical. This finding is significant because (i) the known substrates for the flavoenzymes are organic species and not metal ions, and (ii) the report on the enzymatic formation of the ""OH radical provides a new pathway for understanding the mechanism of genotoxicity of some non-ferrous metal ions. For example, it has been suggested that OH radical is likely to be the major species responsible for Cr(VI) genotoxicity [1-5). The 'OH radical is generated through the reaction of Cr(V) complexes with cellular Hi02 [4,5]. Cr(V) itself is known to be generated from Cr(VI) in various biological systems, in particular, microsomes [ 6), mitochondria [7] and mitochondrial electron transfer chain complexes [8]. However, no specific enzyme responsible for the Cr(V) generation has been identified except possibly glutathione reductase [4]. In this study we have used ESR and spin trapping techniques to show that the flavoenzymes can generate Cr(V) and provide a catalytic redox cycle for 'OH formation in such reactions. Herein we present our results on Cr(VI) and summarize those on other systems. Correspondence address: N.S."

Jan 1, 1990

By W. H. Kerns

The Simon & Coles manganese deposit in Sherman Valley, Bedford County, Pa., was investigated by the Bureau of Mines during the fall of 1942. Two churn-drill holes; 65 and 75 feet deep were bored, and 8 channel samples were taken. Manganese occurs at this property in the form of psilomelane and manganiferous iron as replacement of the red sandy shale of the Much Chunk-formation. Two cars of manganese ore had been shipped by the owners in 1940, of which one averaged 10.9 percent manganese and the other 21.3 percent manganese. One car of hand-sorted manganese ore that averaged-45 percent manganese was shipped in 1942.

Jan 1, 1948

By W. P. Diamond

Coalbeds exhibit a directional permeability, with the maximum permeability oriented parallel to the face cleat. Thus, the most efficient pattern of vertical degasification holes for a coalbed is dependent upon cleat orientation. Surface joints, infrared photolinears, and Ronchi grating photolinears were investigated as potential estimators of subsurface cleat orientation. Cleat orientations were measured in 18 mines, in the Pittsburgh coalbed in southwestern Pennsylvania and northern West Virginia to be used as a standard against which prediction techniques would be evaluated. Two cleat systems with a strong geographic segregation were measured in the study area: N 670 W -N 280 E (950 separation) for the north, and N 76° W -N 17° E (930 separation) for the south. Directional data obtained from the three techniques investigated yielded satisfactory regional predictions of cleat orientation. Analysis of surface joints was the only technique considered sufficiently reliable on a local basis. Prediction of cleat orientation is based on the pairing of the principal directional sets into all reasonable combinations of fundamental systems. The system or systems composed of the most dominant sets nearest to 90° separation are likely to be a reliable prediction of cleat orientation. The most dominant set of the system selected is likely to be the face cleat.

Jan 1, 1976

By V. E. Erwin, W. W. Adams

"Production of explosives for industrial use in,the United States during 1934 continued the upward trend begun in 1933 from the low-level output of 1932, and the output in 1934 was only slightly less than in 1931.Reports to the United Stated Bureau of Mines from companies engaged in the manufacture of industrial explosives showed that the quantity of explosives manufactured in the United States and sold during 1934 for use within the various States was 314,767,922 pounds - 23 percent more than in 1931.Production during 1934 included 39,207,845 pounds of permissible explosives 5 206,625,027 pounds of high explosives other than permissibles, and,68,935,050 pounds of black blasting powder of which 37,192,700 pounds were in granular form and 31,742,350 pounds in pellet form. These figures represent an increase over 1933 of 15.6 percent for permissible explosives, 30.9 percent for other high explosive, and 7.4 percent for black powder.Coal-mining operations were the chief consumers of permissible explosives; 99 percent of the total output in 1934 was used, in coal mines. The proportion used by bituminous mines was 59 percent and by anthracite mines 40 percent. Coal mining was likewise the principal consumer of black blasting powder, taking 88 percent of the total sales during 1934; of this proportion, bituminous mines received 78 percent and anthracite mines between 9 and 10 percent. Consumers of high explosives other than permissibles were more varied; the reports showed that 11 percent of the total quantity sold was for coal mining, 22 percent for metal mining, 17 percent for quarrying and nonmetallic-mineral mining, 46 percent for railway and other construction work, and 4 percent for all other purposes."

Oct 1, 1935

By Susan M. Moore

Many challenges are faced by workers in lower-seam (42 inches or less) mines. The lower-seam heights confine mine workers to their knees as they perform their daily tasks such as installing roof bolts, delivering supplies, repairing belt, or cutting coal. Miners working in these lower seams often consider kneepads to be their only line of defense against knee injuries. However, healthy knees do not start and stop with kneepads. Other interventions such as changing postures, proper hygiene, and work station design may also be used to reduce mine workers? risks for developing knee injuries. Incorporating these and many other interventions into a mine worker?s ?way of life? is an important step to ensuring a long, healthy career and retirement. Keeping knees healthy is also a key aspect to reducing costs in low-seam mines as the industry battles rising health care costs, and training/recruitment of replacement workers is time-consuming and costly. Educating the workforce about the possible interventions to reduce knee injury risk is a primary objective for the National Institute for Occupational Safety and Health?s (NIOSH) Pittsburgh Research Laboratory (PRL). Therefore, NIOSH researchers, along with industry and academia, developed a training package to educate the mining com­munity about some possible interventions beyond kneepads that may be used to help decrease knee injury rates. Increased awareness and simple changes are the first steps to reducing knee injuries.

Jan 1, 2008

By V. Castranova, K. Van Dyke

"I. INTRODUCTIONA mechanism which is present in leukocytes and capable of releasing histamine from rabbit platelets was first described by Barbaro and Zvaitler in I966. A soluble mediator between rabbit leukocytes and platelets was also detected by Siraganian and Osier in 1971. This factor was isolated and characterized in 1971 by Benveniste et al. and named platelet activating factor i PAF). It was shown to be released from rabbit basophils through an antigen - IgE-dependent mechanism. The presence of PAF in human leukocytes' and its aggregation and releasing effects on human platelets were also demonstrated. Chemical analysis has shown that PAF is a glycerophospholipid with a choline polar head group. an ester-linked acyl chain at the second carbon and a nonester link at the first carbon.' The structure of the mediator was found to be 1-O-alky1-2-acetyl-sn-glyceryl-3-phosphoryl choline and it has been chemically synthesized.""' A variable portion exists in the alkyl group attached to the first carbon which can have a variety of molecular sizes such as C and C (where Cu is more abundant). Recent work by Pinckard et al."" has shown that there are at least five variations of the alkyl group.PAF has been shown to have a broad range of biological effects. Release of PAF from alveolar macrophages may be important in asthma, allergy, and shock states. In a rabbit model of antigen IgE anaphylaxsis. PAF can induce all of the effects of antigen challenge and. therefore is presumed to be a key mediator in production of anaphylaxsis. In addition to aggregating and degranulating platelets it is a potent chemoattractant."" and causes contraction of guinea pig ileum contraction of lung tissue and enhanced capillary permeability PAF has important effects in the kidney and is also known as the renal hypotensive factor proposed by Blank et al. who found the structure of PAF independently of Benveniste et al.' In producing these responses. PAF acts by a receptor-like mechanism. In platelets. PAF selectively desensitizes itself but not thrombin or collagen. In smooth muscle tissues a similar phenomenon occurs with anaphylatoxin or other stimuli.In vivo. PAF probably acts in concert with other agents in producing its various biological effects. It causes platelets to release histamine serotonin and RCS (rabbit-contractile substance formed from prostaglandins PPG2, PGH2 and TXA2) which contracts rabbit aorta. PAF can cause cells to release SRS-A and leukotriene B."

Jan 1, 1989

By Thomas E. Green

A gas volumetric method was developed for determining metallic aluminum at the 0.01-to 0.3-percent level in 100-gram samples of recycled glass. The method is based on the measurement of the change in gas volume produced by the reaction 2 Al + 2 NaOH + 2 H2O ? 2 NaAl02 + 3 H2 using a simple apparatus assembled from readily available glassware. Apart from sampling errors, the precision of the method is within ±5 percent. A minor modification of the apparatus would extend the method to larger samples or samples of higher metallic aluminum content. Metallic iron and metallic zinc do not interfere at the concentrations found in recycled glass recovered from incinerator residues.

Jan 1, 1971