Search Documents

By Robert J. Timko

In early June 1986, an underground fire of unknown origin erupted in one of several entries of a coal mine located in southwestern Colorado. For a time, mine personnel aggressively fought the fire. However, control of the fire was later lost. To prevent further damage and reduce the possibility of an explosion, all portals and shafts to the mine were sealed. The mine operator requested the U.S. Bureau of Mines' assistance in obtaining and analyzing mine fire gases taken from sampling ports placed through the mine seals, as well as down boreholes drilled after the fire. This report recounts activities within the first 2 years of the mine being sealed. It includes a description of gases analyzed and mine atmosphere status equations generated from the analyzed gases. The gases were analyzed by chromatography and included standard atmospheric gases as well as higher hydrocarbons that are found in postfire atmospheres. Nine equations were used to evaluate what was occurring within the sealed mine. Following a description of the rationale behind each equation, the 2-year trend is briefly analyzed.

Jan 1, 2010

By James J. Snodgrass

A new technique was used to obtain detailed sonic logging data in drill holes above the water table at a coal mine site in northeastern New Mexico. The equipment was developed under contract to the Bureau of Mines and the U.S. Department of Energy to indirectly evaluate the in situ structural properties of coal and overburden. The system comprises a hydraulically operated, wall-clamping downhole probe compatible with standard four-conductor logging cable, and a surface control module. Resolution of layering is 0.6 meter (2.0 ft), and a redundancy of data from separate receivers provides accurate timing measurements. Preliminary results in the settled overburden of an excavated long-wall panel indicated a low average velocity zone, extending approximately 18 meters (60 ft) into the immediate roof of the coal seam. Subsequent measurements improved the field and recording procedures to produce high quality waveforms from which both P and S arrivals may be visually interpreted. Over a representative section of interbedded sandstone, siltstone, shale, and coal, Vp and Vs varied considerably even within lithologic units. Compressional wave velocity in the coal seam, Vp = 1,740 m/sec (5,700 ft/sec), was in the range of variability of published data.

Jan 1, 1982

By Paul G. Swanson

This manual of practice is to be used in combination with the final reports for the study of spoil stability in the Eastern Coal Province. The manual applies the predictive matrices developed in the parent study for use in evaluating the stability of typical mine spoil slopes. The values of internal friction and pore pressure coefficient are derived for many varied slope conditions. The results can be used in conventional stability analysis equations to assist the mine operator or regulatory personnel in evaluating spoil stability from very limited information.

Jan 1, 1983

By George D. Drechsler

The purpose of this review is to provide an analysis of the supply and demand for coal in Europe in 1955-56 and estimates of future growth in European requirements as a medium for appraisal of the effects and benefits to the economy of the United States. This review stems from observations and evaluations made in contacts with Government and industry representatives of the principal countries of Europe and is based on detailed data selected from the established flow of unclassified economic and statistical material originating in overseas areas for use and deposit in the Bureau of Mines, Foreign Solid Fuels Section. This material includes current reports and analyses prepared by the United States Foreign Service, official reports of individual countries, foreign industry and trade publications, and the committees of the several European organizations engaged in continuing review and study of problems relating to fuels and energy. The review is presented in four sections: 1. Discussion of the more important factors relating to the present and future fuels and energy position of Western Europe.

Jan 1, 1957

By F. P. Miknis

Previous studies at the Bureau of Mines have shown that broad-line nuclear magnetic resonance (NMR) techniques have potential applications for rapid evaluation of oil-shale deposits. In a continuation of this study the techniques of pulsed NMR have been applied in a similar manner. The basis for the pulsed NMR oil-shale assay method lies in the assumption that the free induction decay (FID) amplitude following a 90° pulse is proportional to the potential oil yield. This assumption was tested on two groups of oil-shale samples, numbering 141 and 263 samples, from two different oil-shale cores. For both groups of samples a small number were selected as calibration samples. Free induction decay amplitude measurements were made on the 141 and 263 samples. The best least-squares regression line was obtained for the calibration samples, and the oil yields of the remaining samples were calculated using the slopes and intercepts obtained in the regression analyses. The agreement between measured and calculated oil yields was good, the indexes of determination being 0.93 and 0.89 for the groups of 141 and 263 samples, respectively.

Jan 1, 1974

By A. L. Engel

This report is a compilation of the results of preliminary tests on ores containing scheelite (calcium tungstate). In most of the ores, scheelite was the only value; but several samples contained other values, such as gold, base metals, or, in one instance beryl. These investigations were made to assist the development of domestic tungsten resources by establishing satisfactory treatment methods suitable for small-scale operations. The samples were obtained through the Mining Division of the Bureau of Mines and represent, for the most part, newly discovered deposits. A previous report2/ discussed laboratory test procedures. A less detailed description of test procedures is included in the present report. As is usual in an investigation of this type, only a limited amount of work was done on most of the samples to indicate the results that could be expected from simple treatment of the particular ore. The occurrence of scheelite and the texture of the minerals present differ greatly in individual ores and must be determined and considered in establishing such details of treatment as grinding to obtain optimum liberation of the minerals, the preferred type of gravity concentration, or possible further treatment by flotation.

Jan 1, 1954

By R. W. Hiteshue, R. W. Fridy, W. Kawa

A study of the production of coronene , a high - melting ( 440 ° C ) , highboiling ( 525 ° C) , polynuclear hydrocarbon , was made by the Bureau of Mines to determine the maximum yield obtainable by the hydrogenation of coal and coalderived materials . Experiments were made with anthracite and bituminous coals and with asphaltenes and centrifuged residue obtained from heavy oil produced in a pilot plant by the hydrogenation of a bituminous coal at 2,000 psi and 480 ° C. With anthracite , yields of coronene of 0.5 to 0.7 wt pct of moistureand ash - free coal were obtained at 6,000 to 8,000 psi , 700 ° to 750 ° C , and a residence time of 30 minutes . With bituminous coal , yields averaging 0.4 wt pct of maf coal were obtained at 6,000 psi , 800 ° C , and 30 minutes ' residence time . With asphaltene and centrifuged residue , yields of less than 0.02 wt pct of maf coal were obtained at 6,000 psi , 700 ° C , and 60 minutes ' residence time .

Jan 1, 1964

By F. Matanzo

This guide considers only nine of the many wire rope terminations used in the mining industry so use of the information presented for terminations not specifically addressed can be done, but with some risk. The nine terminations considered are: Flemish Loop with Steel Sleeve & Thimble, Flemish Loop with Steel Sleeve, Wedge Socket, Swaged Socket, Turn Back Loop with Aluminum Sleeve & Thimble, Thimble Splice with Four Tucks, V-Bolt Clip with Thimble, Zinc Poured Socket, and Epoxy Resin Poured Socket. The guide uses pull test data, axial fatigue test data, and data on sensitivity to poor workmanship, to rank the nine terminations with respect to these performance measures. A selection procedure is suggested and illustrated with an example. Failure data is used to identify the common modes of failure of each termination and so help the inspector direct his attention to the likely location for a failure and describe what he should be looking for. The data on which this guide is based is included so that as new data becomes available, the ranking order can be adjusted accordingly.

Jan 1, 1978

By Hillary W. St. Clair

This report gives the results of an experimental study of the progressive changes that occur in particle size and size distribution when a homogeneous and isotropic mineral is subjected to crushing by impact. The mineral used in the study was uniformly sized quartz, which was crushed in a simple drop¬-weight machine that applied impact energy up to about 100 kg-cm per g. Screen analyses of the crushed products were analyzed by the method of moments to determine the mean size, variance, skewness, and kurtosis. Analysis of the data from these experiments shows that the mean size of the crushed product is a function of the energy input and the initial size. The size distribution is functionally related to the degree of size reduction. As the mean particle size is decreased, at first there is a corresponding increase in the variance and decrease in the skewness, But, as size reduction is carried further, each tends eventually to approach a steady value, and the form of the size distribution becomes stable.

Jan 1, 1972

By R. R. Wells

An important activity of the Bureau of Mines is the continual search for new sources of minerals. As a part of the investigation of strategic mineral deposits in the United States, samples of mercury ores were submitted to the Ore Dressing sections of the Salt Lake City and Albany stations for metallurgical testing. This paper gives data summarizing the results obtained from laboratory beneficiation studies of mercury ore samples submitted during the period 1941 to 1947. Ores tested included three from Jackson County, Oreg., one from Valley County, Idaho, one from Storey County, Nev., and one from Sonoma County, Calif. In general, the ores from Oregon were not amenable to concentration by flotation because of intimate association of cinnabar with other minerals or because of extremely low grade. One Oregon ore was amenable to direct distillation provided lime was added to reduce corrosion of the retort.

Jan 1, 1950

By George L. Gates

This report presents is an evaluation by the Federal Bureau of Mines of the effect of clay-water, brine, and oil-base drilling fluids on the productivity of test wells drilled on the Umiat anticline in U.S. Naval Petroleum Reserve No. 4 in northern Alaska. Eleven, wells were drilled on the Umiat structure as part of the U.S. Navy's extensive exploration of the Reserve during 1944-53 to determine the possibilities for oil production. The Federal Geological Survey cooperated in the exploration program and has published a comprehensive report3/ on the geology of the area and case histories of the wells. The re¬port also includes the results of special studies by the Bureau in connection with the drilling and coring of well 9 with oil-base mud in hole and was the source of much of the information used in preparing this publication. Of the eleven wells, four were drilled with rotary tools and water-base mud (one of the water-base muds was an oil-in-water emulsion mud), five were drilled with cable tools with brine in the hole, one was drilled with cable tools with brine in the hole and later reamed with rotary tools and crude oil, and one was drilled with rotary tools and oil-base mud. Although all of the wells penetrated sandstones that contained oil and gas, some were productive and others were not. The latter two wells, one completed with crude oil in the hole (with some added brine) and the other with oil-base mud, had the greatest productive capacities. The wells drilled with cable tools and brine in the hole had lower productive capacities. In contrast, two of three wells completed with rotary methods and fresh-water drilling mud and the well com¬pleted with rotary and emulsion mud were unproductive.

Jan 1, 1960

By J. M. Goris

The U.S. Bureau of Mines is conducting research on cable bolt ground supports to assess their material and support properties, to provide design criteria for using cable bolt supports as roof control systems under various types of underground mining conditions, and to provide a mathematical model of cable bolt support systems. Part 1 describes laboratory studies of the support properties of cable bolts made of conventional steel cables and provides recommendations on such topics as the use of thick grouts, selection of breather tubes, and reduction of water bleeding in cement-based grouts. The studies evaluated both single and double cables; effects of different embedment lengths, water-cement ratios, and grout curing temperatures on support strength; effects of use or nonuse of breather tubes; pumpability and water-bleeding properties of grouts; and the strength properties of sand-cement grouts. Part 2 will cover the strength characteristics of birdcage cable bolt supports, epoxy-coated cables, and cables with steel buttons attached.

Jan 1, 1990

By T. Estelle Gardner

Heat-capacity measurements were made over the range 8° to 350° K on beryllium sulfate dihydrate and beryllium sulfate tetrahydrate using an adiabatic calorimeter. No anomalies were noted in the curve for either compound. Smooth values of heat capacity, entropy, enthalpy function, and free-energy function were calculated from the heat-capacity data at 10° K intervals and at 273.15° and 298.15° K. The entropy values calculated at 298.15° K were 39.01 ± 0.12 entropy units (eu) for the dihydrate and 55.68 ± 0.17 eu for the tetrahydrate.

Jan 1, 1967

By D. W. Frommer

Mineral dressing research was conducted by the Federal Bureau of Mines under a cooperative agreement with the St. Joseph Lead Co., on three samples of iron ore from the Pea Ridge deposit in central Missouri. The objective was to provide information on how to upgrade these submarginal ores and produce marketable concentrates. Samples were prepared from drill-hole cores of similar composition and character to produce (1) a medium-grade mixed hematite and magnetite, (2) a high-grade mixed hematite and magnetite, and (3) a high-grade magnetite. In all three ores phosphorus and sulfur constituted objectionable impurities; excessive amounts of silica were also present in the medium-grade ore.

Jan 1, 1960

By BUREAU OF MINES

This report is submitted in accordance with the provisions of the Synthetic Liquid Fuels Act of April 5, 1944 (30 U.S C. 321-325, as amended), which require that: "The Secretary of the Interior shall render to Congress on or before the first day of January of each year a report on all operations under this Act." Owing to the broad scope of the content and the diversity of interests represented, the Annual Report for 1953 has been divided into two separate publications. Each has been published by the Bureau of Mines as a Report of Investigations, and the respective titles follow: R. I. 5043, Part I - 011 From Coal. R. I. 5044, Part II 011 From 011 Shale. - Identical in each report, the introduction summarizes research progress made in 1953 under the entire Synthetic Liquid Fuels program. A free copy of each of these publications may be obtained by a written request to the Bureau of Mines, Publications Distribution Section, 4800 Forbes Street, Pittsburgh 13, Pa. The R. I. number and title of the publication desired should be indicated.

Apr 1, 1954

By G. W. Grove, O. V. SIMPSON

During the years 1945, 1946 , 1947 , and up to July 1, 1948, only one death was caused by mine fires in bituminous - coal mines of the United States . The one fatality occurred in an Illinois mine in December 1945, and , therefore, there had been a period of 2-1/2 years in which no deaths occurred as the result of mine fires . Moreover, 1946 was the first year since 1930 in which no deaths occurred from mine fires . This record is markedly better than that of 1944 , when 89 fatalities and great property damage were caused by mine fires in bituminous - coal mines and 16 additional men were killed by an explosion that occurred while they were attempting to seal a mine fire .

Apr 1, 1949

By J. S. Dunning

Recent developments in energy conversion, mining and minerals processing, pollution control, and chemical equipment have placed in-creased demands on heat-resistant alloys. Higher corrosion rates from oxidation, hot corrosion, and sulfidation have increased consumption of materials that contain critical and strategic minerals and in many cases have limited productivity. The Bureau of Mines is conducting re-search on substitute materials having greater resistance to high-temperature corrosive atmospheres above 6000 C compared to austenitic stainless steels such as AISI 304, 316, and 310, with the goal of conserving critical metals such as Cr and Ni. The substitute materials are based on Fe-Cr-Ni-Al compositions. Aluminum additions to Fe-Cr-Ni alloys significantly improve high-temperature corrosion resistance, particularly sulfidation resistance. In the alloy, devised by Bureau researchers, aluminum additions are held in the form of a second-phase precipitate, 8NiAl. Minor additions of Ti, Mn, and Si improve workability.

Jan 1, 1984

By Louis C. Brichta

This report summarizes the progress made by the Federal Bureau of Mines in assembling and compiling a catalog of available logs of drill holes and maps of mine developments in the Tri-State Zinc-Lead District in northeastern Oklahoma, southeastern Kansas, and southwestern Missouri. It supplements an interim report (11)3/ published in 1955, and for convenience of the reader repeats much of the general descriptive matter pertinent to the district contained in that report. The work of procuring and recording the data was begun in August 1949 and was recessed in May 1959. The catalog preserves the records of accomplished explorations and mine developments in the district and provides a readily available source of information for individuals and firms interested in planning mineral explorations, Government agencies estimating of reserves of mineral resources, and the mining industry for general use.

Jan 1, 1960

By D. L. Yopps

In research conducted by the U.S. Bureau of Mines, platinum-group metal (PGM) flotation concentrate from the Stillwater Complex, MT, was subjected to biooxidation using Thiobacillus ferrooxidans in an effort to break down the sulfide minerals and liberate the associated PGM's for subsequent chemical leaching. Bacterial preleaching oxidized up to 94 pct of the sulfide present, destroyed the PGM-bearing pentlandite [(Ni,Fe)9S8] mineralization, and dissolved most of the nickel in the concentrate. Cyanidation at 80° C proved to be the most attractive chemical leachant, removing 34 pct of the platinum, 76 pct of the palladium, 94 pct of the rhodium, and 97 pct of the gold from the biooxidized concentrate. Research also indicated that increased sulfide oxidation during the preleach phase led to improved PGM recovery in the subsequent chemical leaching phase.

Jan 1, 2010

By John C. Feeley

This paper is the result of a field study of prospect drilling in the Florida phosphate fields. The objective is to describe the drilling methods employed . . Since the general policies of the operating companies in the land - pebble area do not permit the dissemination of prospecting information and costs thereof , the writer has carefully avoided mentioning names and locations except by reference to existing publications ,

May 1, 1949