Search Documents

By F. X. Tartaron

Behavior of hard-burned quicklime was compared with that of soft-burned quicklime in an oxygen converter utilizing oxygen blowing in a rotating cylindrical vessel, set at a 30° to 60° angle to the horizontal and operated at a predetermined speed of rotation. Four pairs of tests were made) each comparing hard lime with soft lime. Three of the pairs differed from one another in the quantity of lime employed) and the fourth differed in blowing time, All four pairs showed an increase in yield when soft lime was used. Three of the pairs revealed that the ratio of the oxygen consumed with soft lime to the oxygen consumed with hard lime was the same as the ratio of metal yield with soft lime to the metal yield with hard lime. The fourth pair contained an error and could not be included. Finally, a close inverse relation was found between the combined iron in the slag and the combined lime in the slag, which can be expressed by the equation pct Fe = 52.67 -0,906 (pct CaO).

Jan 1, 1967

By D. E. Shanks

The Bureau of Mines surveyed a variety of inorganic ion-exchange materials to determine their suitability for removing valuable accessory elements and troublesome contaminants from metallurgical process and waste streams. Most of the materials, which included molecular sieves, heteropolyacid salts, and hydrous metal oxides, did not give adequate separations, did not have the necessary stability in strong acids or bases, or were not in a physical form suitable for ion-exchange use. Many of the suitable inorganic materials, especially the hydrous oxides, were capable of cation exchange with high capacity only in basic conditions, which caused hydrolysis of most of the cations tested. Multivalent anions, such as arsenate and phosphate, were easily removed from acidic solutions by hydrous oxides. Hydrous zirconia was the best material for this purpose. Multivalent anions were not easily des orbed because of compound formation; therefore, conventional ion-exchange techniques could not be employed. As an alternative approach, hydrous ferric hydroxide was used as a filter material to remove arsenate and phosphate from acid solutions. One gram of arsenic was removed from solution for each 20 g of ferric hydroxide. Ferric hydroxide is preferable to hydrous zirconia for use as a filter material because of low cost.

Jan 1, 1983

By Henry E. Blake

The Bureau of Mines has been engaged in a continuing research effort to develop processes for increasing the recovery and utilization of fluorine from low-grade resources. This current research has shown that over 98 percent of the fluorine in phosphate rock is extracted when the ore is treated with excess phosphoric acid in the presence of water vapor at 150° to 180° C. More than 80 percent of the fluorine can be recovered as fluosilicic acid, which can then be converted to commercially useful hydrogen fluoride or fluorspar by previously developed Bureau processes. Extraction of P205 from the ore was about 98 percent in batch tests and 90 percent in semicyclic tests.

Jan 1, 1974

By Lloyd Williams, H. K. Gibbs, William L. Crentz, J. W. Miller

"Reserves This investigation shows that the Poplar Creek is the most important bed in Scott County from a production standpoint. Although the Poplar Creek bed contains the largest reserve, the Big Mary has a larger recoverable reserve. Estimates of reserves also have been made for the Pewee, Red Ash, Windrock, Upper Pioneer, Jellico, and White Oak beds.Known measured and indicated reserves of coal, based on a minimum bed thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 143 million tons as of January 1, 1954. Of this total, 74 million tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.Recoverable reserves of coal are estimated in beds 28 inches and more thick. This thickness is about the minimum now being mined by hand loading onto conveyors in the Appalachian region. The weighted average recovery for all beds in Scott County, as determined by this investigation, is 52.4 percent. This percentage is based on the total thickness of coal in the bed (less partings three-eighths inch or more thick) rather than on the thickness of the coal mined. Based on the weighted average percentage of recovery for all beds in Scott County, the recoverable reserves of coal are estimated to be 39 million tons as of January 1, 1954.Coal Analyses Chemical analyses of coal samples taken for this study show that the coal in Scott County is of high-volatile a bituminous rank except the Upper Pioneer bed, which is shown to be high-volatile B bituminous. The Pewee bed shows typical low-sulfur characteristics. The high ash and sulfur in the Big Mary are characteristic of that bed. The Poplar Creek is moderately low in ash and sulfur in areas where there is no parting in the bed."

Jun 1, 1956

By Joseph A. Hrabik

The Bureau of Mines compared the feasibility of mining deep phosphate deposits by a borehole mining system with mining by proven conventional techniques. An economic comparison of the borehole mining system with conventional dragline and bucket wheel excavator mining systems was completed at various mining depths and production rates. Hypothetical phosphate deposits, with various overburden thicknesses and reserve tonnages, were defined. Geologic conditions necessary for the application of the borehole system were identified. Discounted cash flow analyses based on derived capital and operating costs were used to generate rates of return and product prices. Borehole mining was found to be more economical where overburden thickness was 150 ft or greater; however, at 50- and 100-ft thicknesses, conventional surface mining was more economical. Overburden thickness has a great effect on the economic feasiblity of the conventional mining systems but less effect on the economics of borehole mining. Economies of scale are only realized in conventional mining, since larger equipment is employed to achieve greater production, whereas increased production from borehole mining is achieved using additional equipment units. A comparison of the environmental effects of borehole and conventional surface mining systems showed that borehole mining is environmentally more desirable.

Jan 1, 1983

By E. R. Palowitch

Coal wasted with mine refuse represents losses in overall recovery of merchantable coal to the mine operator and a concomitant reduction in domestic reserves of available coal. Fraser, Kelley, and Graham3/ in studying the available coal in mine refuse in the Pittsburgh district of western Pennsylvania have estimated that at least 1 ton of mine refuse is produced for each 10 tons of merchantable coal and that 20 percent of this mine refuse might be recovered as salable coal by mechanical cleaning. SUMMARY This investigation dealt with the mechanical recovery of coal from wine refuse by a dense-medium washery employing pulverized mine rock as the dense medium and operating at a rate of 175 tons per hour. Two types of mint refuse were tested: Freshly mined and that .which had been mined 2 years before and piled on a waste dump.

Jan 1, 1955

By Jay W. Hawkins

Under an approved remining program, mine operators can remine abandoned coal mines without assuming legal responsibility for treatment of the previously degraded water, as long as the discharging waters are not further degraded and other regulatory requirements are satisfied. A U.S. Bureau of Mines review of 105 remining permits in Pennsylvania indicates that remining results in substantial reclamation of abandoned mine lands, utilization of significant quantities of coal, and reduction of contaminant loads (acidity and iron) from degraded mine drainage discharges. Normality tests performed on the water quality and flow data indicate generally nonnormal distributions and extreme right-skewness, tending toward lower values. The water quality of underground coal mines was observed to be more highly degraded in terms of acidity, iron, and sulfate than that of surface coal mines. The optimum baseline sampling scenario is 12 months in duration at a frequency of one sample per month. Analysis of water quality and flow rates before and after remining indicates that a majority of the mines exhibited either no change or a significant decrease in pollution rate because of remining. The discharge flow rate was the dominant controlling factor when the post-remining contaminant load was significantly better or worse than the baseline (pre-remining) load.

Jan 1, 2010

By T. S. Chen

A study was made by the Bureau of Mines of the temperature and thermal stress distributions in thin circular disks subjected to peripheral thermal shock at various rates of heat transfer. The theoretical analysis is based on one-dimensional radial heat flow by conduction in the disk, and on heat exchange by convection between the disk and its surroundings. Preliminary experimental data obtained from shock tests on thin circular disks of basalt, quartzite, and taconite show reasonably good agreement with theory. The case of constant properties and plane stress is treated. Solutions of the stress distribution are presented for both cooling and heating shocks. The elastic energy stored at fracture is examined, and on this basis an average stress theory is formulated. Physical properties vital to the studies include thermal conductivity, thermal diffusivity, tensile strength, Young's modulus, and linear coefficient of thermal expansion. This work is of importance in predicting the thermal shock responses of a rock body of finite size.

Jan 1, 1966

By P. C. Good

This Bureau of Mines report describes the preparation of phosphoric acid directly from phosphate ore, without prior beneficiation, in a small-scale, continuous process research unit, as part of an effort to improve minerals and metals recovery from domestic resources while minimizing environmental effects. Three phosphate-matrix samples, ranging in grade from 18.2 pct P20S5to 11.9 pct P205, were dry-fed at a rate of 1.82 kg/hr (4 lb/hr) to a continuous-circuit, 12-liter, single-tank digester to yield phosphoric acid and byproduct gypsum filter cake. Comparison with earlier data shows that a significantly improved filtration rate was attained in a single-tank reactor compared with that attained in a five-tank reactor train processing the same ore. Iron and aluminum impurities in the product phosphoric acid averaged about 60 pct higher than amounts reported in commercially prepared, concentrate-derived acid. All gypsum filter cakes prepared had a firm, sandy texture, rendering them physically suitable for stacking or landfill use. Introduction of dry attritioning and air classification approximately doubled the attainable filtration rate when the dry-beneficiated product was digested. In air classification, there was a 12-to 14-pct P205 loss. Depending on the technique used and the matrix grade, overall P205 recovery ranged from about 72 to 89 pct.

Jan 1, 1979

By Wilbert J. Huff

The organization of the Explosives Division is indicated by the accompanying chart (fig. 1). As this has been discussed in a previous report3/, it will not be considered further in this report. The activities of the various units are outlined below. I. INFLAMMABILITY OF GASES AND VAPORS4/ Determination of the Explosion Hazards of Combustible Gases and Vapors Found in Mines and Industries The Explosives Division maintains, at the Pittsburgh Experiment Station, a laboratory specially equipped for the determination of the explosion hazards of combustible gases and vapors. Of particular importance, is the determination of the chemical composition within which explosions may occur and beyond which there is no danger of explosion, combustion or inflammation. These limits, known as the limits of inflammability, as determined by this and other laboratories, have been compiled in Bulletin 279 of this Bureau. The last revised edition (1931) of this bulletin has been exhausted. Since it was published, the Pittsburgh laboratory has determined the limits of about 40 combustibles and has ascertained more precisely ant accurately many previously published limits.

Jan 1, 1938

The Bureau of Mines is responsible for a broad spectrum of programs for meeting the diverse and changing mineral resource needs of the Nation. These programs are managed by the Director and two Deputy Directors, who formulate general policy and program direction from the Washington, D.C., headquarters. A senior advisory staff, consisting of the Chief Staff Officer, Chief Scientist, and Chief Mining Engineer, provides advice and consultation to the Director on a wide range of scientific and technical matters and acts on behalf of the Director to maintain liaisons with other government agencies, mineral industries, and professional societies. Bureau program activities are classified into two major functions: (1) Developing new and improved technology that will make the production and processing of minerals more efficient, safer and more healthful for mineral workers and the public, and more compatible with a quality environment.

Jan 1, 1980

By J. L. Eakin

The works and opinions of experts on well stimulation and related problems are summarized in this paper. The material is devoted to stimulative work in petroleum and natural-gas wells exclusive of the generally applied pressure maintenance and secondary-recovery methods. Its purpose is to review a collection of recent and available material on well-stimulation methods and techniques. Each separate discussion is accompanied by a selected bibliography. An author index is included.

Jan 1, 1964

By J. L. Eakin

The works and opinions of experts on well stimulation and related problems are summarized in this paper. The material is devoted to stimulative work in petroleum and natural-gas wells exclusive of the generally applied pressure maintenance and secondary-recovery methods. Its purpose is to review a collection of recent and available material on well-stimulation methods and techniques. Each separate discussion is accompanied by a selected bibliography. An author index is included.

Jan 1, 1964

By John C. Hartley

Three systems that monitor ventilating fans are described. These electronic monitoring systems automatically perform most of the operations required to conform with the provisions of the Federal Mine Safety Code in the event of fan failure or slowdown.

Jan 1, 1964

By B. J. Moore

This Bureau of Mines publication reviews U.S. helium resources as of January 1, 1973. These resources, estimated to be 693.7 billion cubic feet, are broken down into four classifications, as follows: helium in storage, 34.9 billion cubic feet; helium in measured helium-rich natural gas reserves, 119.5 billion cubic feet; helium in measured helium-lean natural gas reserves, 62.8 billion cubic feet; and helium in indicated or undiscovered natural gas resources, 476.5 billion cubic feet. The helium in undiscovered natural gas is considered a national resource; however, this gas may not be discovered depending on many factors beyond the scope of this paper, and most of the helium in natural gas will be dissipated as the gas is consumed for fuel and other purposes.

Jan 1, 1976

By John F. Papp

The objective of this U.S. Bureau of Mines study is to calculate an accurate, reliable estimate of chromium and nickel content of stainless and heat-resisting steel produced in the United States. The columbium, manganese, molybdenum, titanium, tungsten, and vanadium contents of this steel are also calculated. Such contents are required for estimating the quantity of alloying element recovered from recycled stainless steel and consumed by market sectors. In this investigation, the elemental fraction of stainless and heat-resisting steel was calculated as the ratio of the weight of element contained in stainless steel to the weight of stainless steel produced. The elemental fraction has been calculated as a time-averaged, grade-averaged value. The elemental fraction was averaged from 1962 through 1983, and averaged over the grades for which production was reported by the American Iron and Steel Institute during that time period. The 1962-83 average elemental fraction of U.S.-produced stainless and heat-resisting steel was calculated for chromium to be about 0.17 ± 0.01; columbium, 0.00014 ± 0.00003; manganese, 0.015 ± 0.005; molybdenum, 0.004 ± 0.001; nickel, 0.07 ± 0.01; silicon, 0.009 ± 0.001; titanium, 0.0004 ± 0.0001; tungsten, 0.0001±0.00003; and vanadium, 0.00003±0.0000l.

Jan 1, 1991

By Robert H. Peters

Groundfall accidents have been the leading cause of fatalities in the underground coal mining industry for many years. Statistics from the Mine Safety and Health Administration (MSHA) indicate that approximately half of the victims of these fatal accidents were in an area where no devices had been installed to support the mine's roof. This report was prepared by the U.S. Bureau of Mines to summarize the opinions of 268 coal miners, 29 rust-line supervisors, and 30 MSHA inspectors concerning why people go under unsupported roof, and how to prevent this behavior. Interviews were conducted at six minesites.

Jan 1, 1991

By W. W. Agey

An inexpensive technique that laboratory studies indicated would significantly reduce seepage in irrigation canals was devised and tested through research sponsored by the Bureau of Reclamation and the Missouri River Basin Field Committee. Laboratory tests simulating optimum field conditions determined that easily applied sodium carbonate solutions made test beds of canal lining materials virtually impermeable for long periods. The study comprised alternative laboratory treatments of 3-inch-deep test beds of canal earths with 74 water-soluble chemicals in search of one 01' more that would effectively improve the water barrier characteristics of the component clays. Sodium carbonate, one of the least expensive, was among the most effective. The addition of 0,4 lb of reagent per sq yd greatly reduced the seepage from typical, highly permeable test beds. The reagent penetrated and sealed surface for about a 1.5-inch depth.

Jan 1, 1965

By Eric R. Bauer

This Bureau of Mines manual is intended to provide a better understanding of ground movement and the technology available for measuring it, The manual deals with convergence, strata separation, lateral roof movement, stress, and support load in underground mines. The instruments that measure these ground control parameters are described in detail. Step-by-step procedures for selecting the appropriate instrument are presented, which consider such factors as approximate cost, installation procedures, data collection, and data interpretation; and an instrument selection worksheet is provided to facilitate the instrument selection process. Actual instrument case studies and a list of instrument suppliers are presented in the appendixes.

Jan 1, 1985

By W. H. Ode

An investigation of standard methods for determining ash in low-rank* coals showed that generally 60 to 95 percent of the total sulfur in the coal is retained in the ash as SO3. This large sulfur retention causes a positive error in the determined mount of ash of as much as 6 percentage points for the coals examined, although it usually is 2 to 3 percentage points for lignites and about 1 for subbituminous coals. Unless the sulfur content is low or unless a correction is made for the SO3 retained, the fixed carbon and oxygen have an equivalent negative error when determined by difference; also other inaccurate analytical values occur when the data are calculated on an ash- free bas is. No simple modification of the ashing procedure was found that would reduce the sulfur retention to a point where its effect on the ash determination would not be significant, Therefore, for accurate analytical work on law-rank coals, the SO3 should be deducted from the determined ash to obtain a "corrected" ash value.

Jan 1, 1962