Search Documents

By Robert E. Wallhagen

The froth foam seal topping system is part of a system for remote sealing of mine passages using flyash transported pnuematically from the surface. Making the final 5 percent of the seal with a foamed-in-place fire retardant polyurethane reduces the required flyash volume by 50 percent and provides a more reliable seal. Foam components are held at the surface under proper conditions of temperature and pressure; then conveyed down the borehole through individual hoses and mixed at the bottom with a static mixer. The polyol component is pre-mixed with fluorocarbon-12 which, when released from system pressure in the mixer, boils and causes the foam to expand. Difficulties in handling this particular foam formulation are offset by a flame spread index well below the 25 level by ASTM E-162 normally required for under-ground applications. Isocyanate, polyol (TDI) and catalyst are conveyed to the downhole package by three separate lines. Five additional lines operate the valving and convey solvent so that the mixer and package lines can be flushed immediately after foaming. The eight-hose bundle is provided in segments of several lengths so that bore-hole depths can be matched. Cast-in-place plastic cylinders hold the bundle together and transfer the weight of the hose through a special quick-release clamp to the crane's wire rope. The downhole package and hose bundle are deployed using a specially designed winch and crane system capable of borehole deployment to 1500 feet.

Jan 1, 1977

By P. B. Altringer

Searles Lake, CA, contains the largest known domestic tungsten resource. The brines in this near-dry lake bed, located in the Mojave Desert 130 mi northeast of Los Angeles, contain an estimated 135 MMlb of tungsten. However, the low concentration of tungsten (0.080 g/L W03) in the supersaturated brine makes selective tungsten extraction very difficult. Although many brine chemicals are extracted from the lake, tungsten recovery was an elusive goal prior to Bureau of Mines development of an ion-exchange technique. This publication describes the Bureau process. The following subjects are ad-dressed: ? The Searles Lake tungsten resource. ? General problems associated with tungsten recovery. ? Bureau research objectives. ? Synthesis of ion-exchange resins. ? Development of a two-stage ion-exchange tungsten extraction and concentration procedure. ? Product recovery and purification. ? Economic evaluation. Flowsheets for recovering three products (calcium tungstate, sodium tungstate, and tungstic oxide) are presented and evaluated, as well as a summary of the research effort and potential applications.

Jan 1, 1985

By Albert W. Deurbrouck

This report describes the preparation characteristics of 23 coal samples collected from nine of the more significant coalbeds of Fayette County, W. Va. In 1963 almost 5.4 million tons of medium to high volatile B coals of excellent quality for metallurgical and steam markets were produced in Fayette County. Of the 23 coal samples collected 11 would require some upgrading to pro-vide metallurgical quality products, 11 were acceptable as received, and 1 was a noncaking coal. Cleaning these coals to metallurgical standards would require only the removal of the sink 1.58 specific gravity material which would be quite easy as very little near-separating-gravity material was present at this gravity.

Jan 1, 1965

By William E. Dennis

"At the request of Philip S. Hoyt, the Eagle Mountain fluorspar deposits in section 35, block 68, Texas & Pacific Railroad Survey No. 9, were examined by an engineer3/ of the Bureau of Mines during March 1943: As a result of this examination; a preliminary program of trenching, sampling and core drilling by the Bureau of Mines was begun in. June 1943.4/ Eight deposits were explored.The Federal Geological Survey mapped the properties and furnished geologic information throughout the program, while the Texas .Bureau of Economic Geology6/ made preliminary maps that facilitated planning the exploratory work on section 35.The eight deposits explored by the Bureau of Mines are in block 68, Texas & Pacific Railroad Survey No. 9, Hudspeth County, Tex., approximately 7-1/2 miles south of. Hot Wells and 12-1/2 miles south of Allamoore, which is 10 miles west of Van Horn and 20 miles east of Gierra Blanco on U. S. Highway 80(fig. 1). A graded gravel road, built by the Public Roads Administration, leads from Hot Wells to the deposits in section 35, and there are unimproved roads, passable,by automobile, to all the other deposits.Carload shipments can be made to and from Hot Wells on the Southern Pacific Railroad, and complete railroad facilities are available at Allamoore on the Texas & Pacific Railroad.Van Horn and Sierra Blanca are the only local source of labor and. supplies. The prevailing wage for common labor is 60 cents an hour. Living accommodations are obtainable in Horn and Sierra Blanca.No electric power lines pass near the deposits. Diesel and gasoline motors are employed to furnish power for mining and milling operations.Two recently 'drilled water wells on section 35 furnish water for the mill. Other wells will be drilled if the present supply is inadequate for prolonged Peak operation.The properties lie in the foothills on the northeast side of the Eagle Mountains at 5,500 feet altitude. The Eagle Mountain Range rises sharply from a broad, flat valley known as Eagle Flat. Eagle Peak, the highest in the range, has an altitude of 7,510 feet. In the vicinity of the fluorspar deposits the topography is moderately reliefs ranging from 50 to 300 feet."

Jun 1, 1946

By R. A. Friedel

THE UTILIZATION by the Bureau of Mines of infrared and ultraviolet-visible spectrometry in connection with coal research has led to some basic improvements in methods, including a calibration method, a quantitative assessment of infrared spectral energy sources, and the development and perfection of infrared filters and cells. The adoption of a micropipet method to flush organic samples into absorption cells permits the investigation of vapors from organic liquids and the identification of volatile organic compounds. The spectral method has been used to investigate the infrared spectra of metal chelates, the charge-transfer complexing properties of aniline and nitrobenzene, an infrared method for determining the presence of methane in coal-mine air that has been adopted for use in enforcing the regulations of the National Coal Mine Safety Act, and atmospheric pollution including smog and odor-causing oxidation and decomposition of organic materials. Correlation of spectra and structure of organic compounds, particularly aromatics, was studied.

Jan 1, 1966

By W. Hodge Caraway

This report presents the results of an evaluation of several indirect methods of measuring the water content of oil-reservoir rocks. The water content of oil-base cores is considered to be most nearly representative of the water content of the undisturbed petroleum reservoir and therefore, the direct method of measuring the volumes of water in cores cut in oil-base drilling fluid was adopted as a standard for comparison. The indirect methods evaluated included (1) displacement through a semipermeable membrane by air, (2) centrifuge, (3) evaporation, (4) mercury injection, (5) chloride dilution and (6) electric logs. Approximately 270 samples of cores from petroleum-reservoir rocks were used in the study. The cores, most of which were cut with oil-base mud in the hole, were taken from oilfields in California, Texas Gulf coast, Colorado, Oklahoma, and Alaska.

Jan 1, 1959

By William S. Roberts

As part of the Bureau of Mines critical and strategic minerals program in Alaska, 34 high-purity chromian spinel samples were analyzed for trace and major element geochemistry and mineralogy. The samples were analyzed by X-ray diffraction, X-ray fluorescence, and chemical techniques. Systematic differences in chemistry are evident when samples collected from the Chugach Mountains and their related extension are compared with chromian spinel samples collected from interior Alaska. Compared with the Chugach samples, the interior Alaska samples have higher average amounts of A1203, Fe203, Ti02, and NiO, have lower average amounts of FeO and Cr203, and exhibit greater dispersion in values. Considerable mineralogical variability of chromian spinel exists between and within individual Alaskan chromite-bearing ultramafic complexes. Of 34 samples analyzed, 25 samples are magnesiochromite, 5 are chromite, 3 are spinel, and 1 is hercynite. As a group the interior Alaska samples have a smaller average unit cell dimension than the Chugach group of samples. The chemical and mineralogical differences between the two groups of samples can be attributed to different genetic histories and may have implications for locating chromian spinel deposits amenable to standard beneficiating techniques.

Jan 1, 1985

By W. S. Landers

This bulletin is a detailed study of low-temperature, entrained-bed carbonization of a Texas lignite. The lignite studied was from the Sandow strip mine and is representative of the Rockdale formation of the Wilcox formational group. Carbonization was conducted in a continuous entrained-bed reactor at several temperatures in the 8801 to 1,52°C F range, and at air-coal ratios it the 0 to 10.30 scf/lb range (moisture- and ash-free basis). Carbonization rates ranged from 97.1 to 410.0 lb/hr (as-received basis), At the higher air-to-coal ratios employed, all or most of the carbonization heat was provided by internal combustion with air in the reactor. At the lower air-to-coal ratios, parts of the heat for carbonization was supplied externally. It was demonstrated that the entrained-bed carbonization of lignite is a complex reaction and that several variables, of which carbonization temperature, air-to-lignite ratio, and the average size of lignite are important, act together to influence both the carbonization yields and the properties of the resultant products, Process variables established by pant tests were used to design the industrial scale carbonizer operated at Rockdale, Texas, by the Texas Power & Light Company as agents for the Aluminum Company of America. Properties of the carbonization product obtained from the industrial scale reactor were essentially the same as those obtained from the pilot plant reactor operated under the same conditions.

Jan 1, 1968

By K. O. Bennington

The thermodynamic properties of two manganese silicates, pyroxmangite and fowlerite (zincian rhodonite), were experimentally determined by the Bureau of Mines. The standard enthalpies of formation were determined by hydrofluoric acid (HF) solution calorimetry, the low-temperature heat capacities by adiabatic calorimetry, and the high-temperature heat capacities by differential scanning calorimetry over the range 322 to 1,372 K. Data for the standard enthalpy of formation (AH298), the derived standard entropy (S298), and the standard Gibbs energy of formation (AGf 298) are as follows: Pyroxmangite [(Mn0.9554Cao,0446)(Si03)J- AHf298 319.668±0.46 kcal/mol AH298 (from oxides)... -7.215±0.11 kcal/mol 5295 23.785±0.048 cal/(mol'K) AGf298 -301.190±7.96 kcal/mol Fowlerite [(Mno.7o3Zno.0884Ca0.2086)(Sio3)]--AHf298 ?... -329.914±0.419 kcal/mol AH298 (from oxides)... -8.400±0.104 kcal/mol 5598 21.949±0.059 cal/(mol-K) AGf298 -310.716±7.99 kcal/mol These experimentally determined values were combined with data from the literature to calculate the Gibbs energies and equilibrium constants of formation over the temperature range of the measurements. Standard enthalpies, Gibbs energies, and equilibrium constants of formation are given as a function of temperature from both the elements and the constituent oxides.

Jan 1, 1987

By H. H. Heady

A naphtha obtained by destructive, recycle hydrogenation of crude shale oil, produced by gas-combustion retorting of Colorado oil shale, was found by the Bureau of Mines to contain 49.1 percent paraffins, 20.3 percent cycloparaffins, 7.8 percent olefins, and 22.8 percent aromatics. The naphtha contained only minor amounts of sulfur, nitrogen, and oxygen compounds. Compounds containing less than 5 carbon-atoms per molecule were removed by distillation before analysis. The paraffins where predominantly straight-chain compounds; n-Hexane was present in the largest quantity, and the other straight-chain paraffins decreased in amount as the molecular weight increased. The cycloparaffins, which contained both cyclopentanes and cyclohexanes, were evenly distributed throughout the boiling range. Although the naphtha had been produced by hydrogenation, it contained a small quantity of olefins. Straight-chain olefins with a terminal double bond comprised about two-thirds of these compounds. Among olefins with an internal double bond, those having trans configuration were present in three times the quantity of those in the cis form. In the aromatics all but one of the alkylbenzenes having nine or less carbon-atoms per molecule were identified; toluene was present in the greatest quantity. Only a few of the higher molecular-weight homologs were identified. The composition of the naphtha was computed from analyses of 105 narrow¬boiling distillation fractions. Volume, density, refractive indices, bromine number, and an ultraviolet spectrum were determined on each fraction. From these data the hydrocarbon-group composition of each fraction was estimated. A silica gel adsorption analysis was used to check the values of nearly one-third of the fraction calculated from physical-property data. Mass and infrared spectra were obtained on some fractions for identifying individual compounds or types of compounds, such as terminal olefins.

Jan 1, 1960

By G. R. Strimbeck

The Federal Bureau of Mines has been developing processes for producing synthesis gas directly from coal, oxygen, and superheated steam. An atmospheric-pressure pilot plant was constructed and operated to: 1. Determine the operability of the plant for gasifying coals of different ranks under various operating conditions. Listed in decreasing order of rank, these coals included a Pennsylvania anthracite, a bituminous A coal from the Sewickley bed, West Virginia, and a subbituminous C coal mined in the Lake de Smet region of Wyoming. 2. Determine the effect of varying operating conditions on: (a) Standard cubic feet (std.c.f.) of oxygen and pounds of coal of different rank required to make M std.c.f. of product gas (carbon monoxide plus hydrogen); (b) carbon gasified, percent; (c) exit-gas temperature, degrees F.; and (d) heat loss, B.t.u. per pound coal. 3. Compare the gasification characteristics, indicated in item 2, of coals of different rank: Bituminous A, anthracite, and subbiturninous C. 4. Determine the concentration of dust in the gases produced and the efficiency of dust removal, and investigate the relation between the sulfur content in the coals gasified and the gases produced.

Jan 1, 1960

By J. C. Edwards

The Bureau of Mines developed a mathematical model for analysis of the impact of scrubber bed length, porosity, and gas flow rate on the absorption of C02 in a breathing apparatus. The model accounts for the decrease in available absorbent through chemical conversion. The pre-dicted efflux of C02 from a canister containing LiOR compared favorably with measured values reported elsewhere. It was determined from a com-putational study that the time for breakthrough of C02 at a prescribed level is nearly directly proportional to bed length and inversely pro-portional to gas flow and porosity.

Jan 1, 1987

By Robert H. Peters

This report presents a literature review conducted by the U.S. Bureau of Mines. The review summarizes what has been learned from recent empirical studies of the relationship between mine safety and characteristics of miners, mine management, and mining companies. The review is based on literature published in the United States during the period from 1976 to 1988. In addition to summarizing the empirical findings, this report discusses the implications and limitations of these studies, and gives recommendations for improving mine safety. An annotated bibliography section appears in the appendix.

Jan 1, 2009

By R. A. Kearns

To enable the mining industry to be kept informed as to the availability of equipment developed by mining equipment manufacturers in their constant endeavor to keep a step ahead of changes in mining techniques, the Bureau of Mines periodically issues lists of equipment approved subsequent to the last previous listing. The present list covers those approvals issued during calendar years 1953 and 1954. It supplements Bulletin 543, Permissible Mine Equipment Approved to January 1, 1953. The procedure established in Bulletin 543 of numbering items in each category consecutively to indicate the chronological order of the approvals has been continued in this circular. Information on approvals issued later than January 1, 1955 may be obtained by referring to Coal Age, a monthly magazine issued by the McGraw-Hill Publishing Co.

Jan 1, 1955

By H. D. Hess, C. P. Mabie

This report describes in detail the results of petrographic research conducted on 21 phosphate ores representing important deposits in southwestern Montana , southeastern Idaho , and northeastern Utah . The ores are described and categorized by mineralogical and chemical composition , thermal behavior of organic carbon , and textural constitution . Descriptive and genetic classification schemes applicable to western phosphate ores are discussed ; results from related studies made of the collophane mineralogy are also presented . The latter studies were centered on determining unit - cell dimensions and CO₂ , P2O5 , and fluorine content of collophane concentrates of 11 high - grade phosphate- rock hand specimens selected solely for this purpose . On the basis of this investigation , operational methods have been developed for quantitatively describing textural and compositional features that are likely to be significant in determining the response of phosphate ores to conventional beneficiation treatments ; systems for classifying the ores in relation to these features have been proposed . Studies to date point out distinct textural and compositional variations in the western phosphates and illustrate their importance in determining optimum beneficiation procedure .

Jan 1, 1964

By Maria I. De Rosa

The U.S. Bureau of Mines conducted a study to determine if correlations exist between the chlorine or nitrogen contents of materials and the hydrogen chloride (HCI) or hydrogen cyanide (HCN) concentrations evolved during the thermal decomposition of these materials. Hydrogen chloride, hydrogen cyanide, and carbon monoxide (CO) were found to be the primary toxic gases evolved during the combustion process. The experiments were carried out in a 20-L furnace with 1-g samples. The furnace temperature, rising from ambient, was set at 1,000 °C with an airflow of 10 L/min. The variables measured were the gas loads (milligrams per gram) of HCI, HCN, CO, and CO2 (carbon dioxide); CO and CO2 concentrations as a function of time were also measured. Other variables included the average concentrations of submicrometer smoke particles and particles' average diameter, mass of particulates, sample and furnace temperatures, and sample weight loss. The data indicate that there are significant correlations between the percentage of chlorine or nitrogen contained in the original samples and the HC1 or HCN concentrations evolved during the combustion of the materials. These correlations may be used to predict and evaluate a material's toxic hazard during combustion.

Jan 1, 2010

By E. C. Lane

This paper is a preliminary report of the results of the Bureau of Mines' twenty-second semiannual survey of motor gasoline marketed in the United States. A more detailed discussion of the whole survey is in preparation and will be published as a companion, report. The second paper, in addition to giving a more complete summary of the data included in this report, will present results of the determination of copper-strip corrosion (method 530.22),5 color (method 10.11),6 sulphur content (method 520.11) copper-dish evaporation residue (method 520.11),7 and gum content as given by the Bureau of Mines steam oven method.9 The retail price at the time the sample was taken and try will also be stated for each sample. The present paper deals specifically with data relating to gravity, vapor pressure, and distillation.

Jan 1, 1930

By Liming Yuan

[ ]

Jan 1, 2009

By D. Harrington, W. J. Fene, H. B. Humphrey

In the fiscal years 1946 and 1947 the number of mine explosions decreased compared with the preceding years. However, the loss of life was so serious during the fiscal year 1947 the period when the Government administered bi- tuminous-coal and lignite mines that from April to June 1947 extraordinary measures were taken in mines then under Government possession to obtain com- pliance with provisions concerning rock dusting, ventilation, and blasting that had not been followed. The great loss of life in explosions during the fiscal year 1947 as compared with 1944, 1945, and 1946 is not easy to explain, but the necessity for maintaining adequate protection has been definitely demonstrated. Management, workers, and inspection agencies alike must keep the mines reasonably safe against explosions or allow them to lapse into a condition where chance is the principal protection against disaster. The at- tention given to protecting coal mines and the men employed in them against mine fires, following the disastrous fires in 1944 and 1945, has at least tem- porarily controlled this hazard loss of life from coal-mine fires was re- duced to 1 fatality in 1947. The number of fires was also less, and progress has been made in reducing the heavy losses in both life and property from un- derground coal-mine fires that occurred in the two years mentioned. Fatalities from mine explosions during the past 6 fiscal years, July 1942 to June 1947, totaled 674, and there were 149 explosions; during the preceding 6 years there were 655 fatalities in 132 explosions. The 6 fiscal years 1942- 47 cover the active period of Federal coal-mine inspection. During the fiscal year 1947, there were 154 fatalities from explosions compared with 58 during the fiscal year 1946, 64 in 1945, 94 in 1944, 152 in 1943, and 152 in 1942.

May 1, 1948

By D. W. Bridges, Donald R. Peterson, Masami Hayashi

Techniques are described for recovering about 80 pct of the cobalt and nickel contained in superalloy scrap by anodic dissolution of the scrap and simultaneous electrodeposition of a pure cobalt - nickel alloy at the cathodes in an electrolytic cell partitioned by permeable diaphragms into separate anode and cathode compartments . Superalloy scrap was alternatively prepared for subsequent anodic dissolution either by melting and casting massive scrap into suitably sized anodes , by packing moderate - sized discard scrap in inert metal baskets that subsequently served as anodes , or after concentrating the superalloy portion of grinding debris , by magnetic separation to reject corundum or other abrasives , slagging any remaining abrasives from molten grindings , and finally casting the superalloy metal into anodes . In the processing , purified electrolyte -- 1 N in NiSO4 and in NiCl₂ , and 0.1 N in CoSO4 and in CoCl2 --was charged to the cathode compartments and discharged from the anode compartments at a rate sufficient to overcome the backward migration of ionic impurities from the anodes to the cathodes . Discharged electrolyte was purified by reacting it first with SO2 and next with limestone , and then recirculated to the cathode compartments , in which a 50 pct cobalt - 50 pct nickel alloy was deposited on either blanks of stainless steel or starting sheets of cobalt - nickel alloy . The process was made self - sustaining by either adding H2SO4 to the catholyte feed to throttle the rate of cobalt - nickel deposition , thereby compensating for the slower rate of cobalt - nickel dissolution from the anode and losses occurring in electrolyte purification , or alternatively , adding H₂SO4 to

Jan 1, 1964