Search Documents

By George W. Healy

The direct retorting of zinc sulfide concentrates in the presence of lime and carbon was examined on a laboratory scale with ten-gram charges of loose mix or fifteen-gram ones of pellets. A slow stream of nitrogen swept through the furnace tube over the boat of reactants, carrying with it the zinc vapor, which condensed on a rolled-up steel sheet near the exit, permitting weight of zinc produced to be obtained after completion of a run. Variables explored were percent of theoretical reagents, temperature, and time. During the runs gas samples were analysed periodically, and the content of CO2, CO and nitrogen were obtained. The quantities of the carbon gases could be calculated because the nitogen flow rate was measured. The gases were also examined for sulfur species, but neither COS nor SO2 could be detected at maximum sensitivity. Zinc recovery increased with excess carbon and lime and with temperature. It ranged from 77% at a ten percent deficiency to 90% at a ten percent excess at 1100°C. Going to 1200°C and theoretical reagents gave 93% recovery. Increasing time from 200 minutes to 300 minutes increased zinc yield by up to 10%. Results from sphalerite and a commercial concentrate from AMAX gave generally similar results. The reaction rate of zinc sulfide as sphalerite and of calcined sphalerite indicated that the latter reacted almost twice as fast, and recovery of zinc was five percent higher. Though the retorting step using sulfide, lime, and carbon proved to be non-polluting, it was feared that on storage the calcium sulfide in the residues would decompose, giving off noxious gases. Consequently the stabilization of the residues by oxidation was essayed. Because of the presence of unreacted zinc sulfide, the first product of oxidation was S02. Reaction of CaS to CaSO4 was incomplete, going from 20% at 800°C to 90% at 1200°C. Thus the non-polluting nature of the process as a whole is in doubt, and its economics are likely to be unfavorable compared to the traditional way of calcining the concentrates, followed by retorting of the oxide with carbon.

Jan 1, 1982

By Lloyd Williams, James R. Boyle

The mining methods and practices used at the Young zinc mine, American Zinc Co. of Tennessee, have resulted in a low-cost, high-yield operation. Zinc ore (sphalerite) occurs in limes tone- dolomi te beds of the Kingsport Formation and is mined by modified room and pillar method. Utilizing trackless mining equipment which incorporates a high degree of flexibility, this operation has had a steady increase in productivity.

Nov 1, 1964

By Homer J. Ballinger

The Alma, Degraff and other mines controlled by the Mon-Ark Mining Co. comprise one of the more important groups of zinc-lead mines in Christian County, Mo. The mines were first operated in .1857 and produced more than 5 million pounds of lead from rich, shallow ore deposits. Recent exploration and development led to the discovery of zinc sulfide ore at a depth of 165 to 214 feet in the northern part of the Alma mine. After examination of these mines in September 1942 by Bureau of Mines engineers, investigation of the extension -of the Alma mine and of the depth of mineralization at the other mines appeared justified in order to encourage the production of additional zinc and lead for war purposes. Twenty-nine churn-drill holes totaling 6.463 feet of bore were completed by the. Bureau from September 1943 to January 1944.

Jan 1, 1948

By Paul M. Tyler

Masurium and rhenium are two elements known only to a few scientists and known to them for scarcely more than five years . The existence of two members of the manganese family was long suspected , and places were left for them in the orderly table of the periodic systemas developed by Mendeljeeff . The empty spaces left in this table some 60 years ago were for elements numbered 43 and 75 , respectively , and since it was evident these were related to manganese they were sought for in research laboratories under the names of ekamanganese and dvimanganese . This nomenclature is in harmony with that usually employed in describing hypothetical elements , and the prefixes are taken descriptively from ancient Sanskrit wherein the word " eka " means one and " dvi " ( also spelled dui or dwi ) means two . Ekamanganese or element 43 was once removed and dvimanganese or element 75 was twice removed from manganese . It was further possible to predict that these elusive elements would not only be related to manganese but would have a great deal in common with certain other elements . It was reasonable to suppose that element 43 , merely because it stood in numerical sequence between element 42 and element 44 , would likewise prove to be intermediate in many other respects . Since its next neighbors were molybdenum ( No. 42 ) on the one hand and ruthenium (No. 44) on the other , ekamanganese could be given in advance what would correspond among persons to a social and economic rating . Similarly , the properties of dvimanganese were likely to be in simple harmony with those of tungsten and with those of osmium , which latter , like ruthenium , is a member of the platinum group of metals . Another inference , although one which could not be stated with scientific certainty , is that these new elements because they have odd instead of even atomic numbers , would be even more sparingly distributed than their near neighbors , none of which is abundant in nature . This inference has been amply supported by available evidence . These elements eluded discovery until 1925 and never have been found except as minute traces in complex association with relatively rare minerals . In 1930 , for the first time , rhenium became available in quantities which give promise of commercial possibilities , but masurium still stands on the border of the unknown , like some distant star speck photographed and identified by vigilant astronomers but invisible without the aid of the powerful tools of science . The telltale flame of element 43 has been charted by its spectrum lines ; but beyond that , little more can be said except perhaps to repeat the forecasts made for ekamanganese before the Noddacks captured it and gave it a definite name . Certain rare - mineral dealers will furnish molybdenite samples from Norway which are said to contain masurium as well as rhenium , but except for a few highly technical statements as to its behavior in the spectrograph , nothing in the way of concrete information on masurium has come to the notice of the present writer . The literature of rhenium is a little less meager and a brief résumé of the data available in the files of the Bureau of Mines may be of interest not merely because of the novelty of the metal but because its unique properties and increasing availability afford a prospect of its finding employment in industry .

Jul 1, 1931

By R. Karl Zipf

In some instances, extensive room-and-pillar working scan collapse with little warning and pose a serious risk to underground miners. Traditional strength-based pillar design methods applicable to coal or hard-rock mines use a factor of safety defined as pillar strength divided by pillar stress. Factor of stability, defined as local mine stiffness divided by post-failure pillar stiffness, may offer a way to design room-and-pillar mines and eliminate collapses. Three alternative design approaches to decreasing the risk of large-scale catastrophic collapses are described: the containment approach, the prevention approach, and the full-extraction approach. Until good data on the post-failure behavior of pillars become available, the containment and full-extraction options are the safest. The limitations in our ability to evaluate both the stability of old workings and the long-term performance of room-and-pillar mines are described.

By Daryl R. Tweeton

The Bureau of Mines is investigating possible applications of geophysics to monitor leachate during in situ mining. Tomographic reconstruc-tion of seismic or electromagnetic crosshole data appears applicable. The tomographic program BOMTOM (Bureau of Mines tomography) was written and then used to investigate reconstructions with synthetic travel time data. The calculations confirmed that without constraints, crosshole data do not provide unique solutions. The solution is not determined solely by the data, but is also influenced by the velocity guesses starting the iterative solution procedure. The effectiveness of constraints in combatting nonuniqueness was examined. The requirement that the velocity not vary laterally at the top and bottom of the pixel grid was effective. This constraint is realistic when the top and bottom of the grid represent dry and saturated re-gions, respectively. Limiting the maximum velocity improved reconstructions, but may not be applicable in practice. BOMTOM uses the simultaneous iterative reconstruction technique (SIRT) with straight ray paths. The program is efficient in use of memory, and can be run on a personal computer. A source code in FORTRAN is listed. A source code in BASICA and compiled executable codes in both languages are available from the Bureau's Twin Cities (MN) Research Center.

Jan 1, 1985

By Joseph A. Olmstead

Literature concerned with management and supervisory training was reviewed and analyzed from the perspective of relative effectiveness of various training methods for improving knowledge and awareness, changing attitudes, improving problem solving skills, improving interpersonal skills, and improving on-the-job performance. Conclusions were drawn relative to each method and the current state of the field of management and leadership training. A 168 item annotated bibliography is presented.

Jan 1, 1980

By S. J. Broderick

[The discovery in 1934 that carbonaceous materials, such as coal, peat, and lignite, when treated with concentrated sulfuric acid, were given cation or bate-exchange properties opened up a field of new materials with many interesting possibilities. These hydrogen exchangers, as they were called, were so superior to the impractical hydrogen exchangers made from natural and synthetic zeolites tat they were accepted immediately by the water-conditioning industry. A noteworthy advantage of the carbonaceous exchangers is that they are nonsiliceous, hence they do not give up silica to the water as do the natural and synthetic Zeolites, especially if the hard water is corrosive. For this reason the new exchangers found immediate favor in boiler-feed-water conditioning.]

Jan 1, 1941

By W. D. Riley

The Bureau of Mines is conducting research on methods for the rapid identification and sorting of mixed scrap metals and alloys so that domestic scrap resources can be fully utilized. One method, spark testing, is the examination of the pattern of sparks that results when a metal or alloy is ground on an abrasive wheel. This technique requires experienced sorters. Bureau researchers have shown that spectrophotometric methods can be used in lieu of the highly skilled sorter. The spectra of a mild steel, an HSLA steel, several stainless steels, and four nickel-base alloys have been measured. Differences in the spectra that are sufficient for identification are apparent.

Jan 1, 1985

By N. A. C. Smith

[The beau of Mines made its first survey of motor gasolines sold throughout the United States in 1915, a second in 1917, and a third in April. 1919. These surveys shored that motor gasoline had become notably less volatile during each two-year interval. In order to ascertain whether this change was continuing, it was planned to institute semi-annual surveys, the first of which teas made in January, 1920. Contrary to expectations based on the previous surveys, the average volatility of the gasoline tested at this time was practically identical with that of the average volatility of the gasoline from the same districts in 1919. The next survey, made in July, 1920, showed a very marked decrease in volatility but as it has long been recognized that the volatility of motor gasoline manufactured for sale during the summer months is loss tan that of gasoline made and sold during the winter, part at least of the change was attributed to this factor. The average boiling point of the samples collected in the present survey is 263 degrees Fahrenheit, as compared with 264 a year ago. This shows that the average gasoline marketed at the present time is fully as volatile as that marketed a year ago. There has been, however, a noticeable change in the character of the product: the initial boiling point and 20 per cant point are lower than a year ago, whereas the 90 per cent and end-points are higher, which indicates a greater proportion of gasolines made by blending casing-head, or natural gas-gasoline, and naphtha.]

Jan 1, 1921

By W. W. Adams

The metal and nonmetallic mineral mines (excluding coal mines) of the United States had a more favorable safety record in 1935 than in any year except 1931 and 1932 since annual statistics of accidents first became available in 1911. The accident rate was even lower than that for 1911, when the recorded rate probably did not reflect all of the accidents that actually occurred because many companies had not yet begun to keep complete records of accidents, especially those causing only minor injuries, and when, therefore, the number of accidents revealed by the companies' reports to the Bureau of Mines was probably not as complete as that reported for later years. Compared. with 1911, the accident rate covering fatal and nonfatal injuries in. 1935 decreased 13 percent. Compared with 1925, when the rate was the highest ever reported, the rate for 1935 decreased 47 percent and compared with 1934, 7 percent. The progress in safety which the mines of the country made in 1935 was not confined to any section or mining region; it was shared by a majority of the mining States and applied to underground mining operations, to open-pit mining, and to work at surface shops and yards. The rate for underground mining declined 8 percent from 1934; the rate for open-pit mining declined 14 percent, and that for surface shops and yards 12 percent.

Jan 1, 1938

By F. L. Wideman

This report describes a computer program that is used for the calculation of the coordinates and elevations of subsidence survey pins located by intersection. This program was developed for the Federal Bureau of Mines by the Numerical Analysis Laboratory, University of Arizona. These calculations, although relatively simple, are both tedious and time-consuming when computed with a desk calculator and trigonometric tables. In this survey, a large number of pins were surveyed repeatedly, and it was evident that both time and money could be saved by using a digital computer.

Jan 1, 1962

By Gene R. Reid

The contract objective is the development and in mine testing of an Automatic Fire Control System (AFCS) for mobile underground metal mining equipment. The effort described by this report covers the period from June 21,1975 through June 30,1976 and accomplished the following tasks: ? Preparation of Data Handling Plan and data acquisition which included visits to twenty mine sites in eleven states, visits to Bureau and MESA facilities, and a literature survey. ? Data analysis which determined the most hazardous type of vehicle for use in the demonstration, and design requirements for the AFCS, ? Development of recommended design concepts for the AFCS. ? Design and development of the AFCS including tests on a full-scale mock-up of a load-haul-dump (LHD) vehicle. ? Underground fire tests on an ST-2B-LHD vehicle at the Hecla Lakeshore mine Casa Grande, Arizona.

Jan 1, 1976

By S. H. Ash

A CLAY, sand, and gravel deposit known as the "buried valley" of the Susquehanna River is situated in the Northern field of the anthracite region of Pennsylvania near Wilkes-Barre. The presence of this buried valley and the uncertainty regarding the extent and physical condition of the water-bearing valley-fill deposits have made great care necessary in mining operations to avoid breaking the strata between the mine workings and the valley-fill deposits to the extent that inundation of the mine workings would follow. The principal factor that threatens to cut short the life of the anthracite industry, to curtail production, and to affect the economic structure of the people and business dependent on anthracite for their livelihood is inundation of anthracite mines (6,7).3

Jan 1, 1950

By Mark L. Chatman

The U.S. Bureau of Mines studied mineral resources of the Dragoon Mountains Unit, Coronado National Forest (54,264 ac), Cochise County, AZ. This study involves literature and field investigations with a focus on mine and prospect sites, which were inventoried and mapped; maps are contained in this report. Rock-chip samples were taken from mineralized zones and from some mine dumps; assays of the 477 samples are in appendixes. Mineral deposits are genetically and spatially related to Tertiary-age granitic intrusive activity. Most metallic mineral deposits are also strongly fault-controlled. Colored marble resources (270,000 st) are valued at approximately $6.5 million, if all were to be developed and sold as landscaping material in the form of-marble chips. However, with current demand, it is unlikely that regional markets could absorb all this material. Economic modeling of copper-zinc-silver skarns suggests none would be profitable to mine and capitalize at early 1993 commodity prices, mainly due to the small estimated size of the deposits (30,000 st to 40,000 st maximum). In the entire Unit, 140,000 st of inferred subeconomic skarn resources were estimated by USBM on five different skarn trends; measured subeconomic resources are negligible. Exploration by industry, 1992, was small-scale (on 2 skarn trends and 1 auriferous fault zone).

Jan 1, 1993

By Charles Seitz

The Bureau of Mines has modified its parts-per-billion helium-4 analyzer to improve the analytical capabilities of the instrument. The modifications resulted in the following improvements: (1) The analytical precision of the instrument for 10 consecutive analyses was improved to ±1 ppb at the 5,000-ppb helium-4 level, (2) the helium-4 sensitivity was increased almost tenfold, and (3) the minimum detectable limit for helium-4 was improved to 0.5 ppb. The modifications made to improve the instrument included replacing the ion-source control circuit with a direct-current solid-state design, controlling the temperature of the ion source, stabilizing and reducing the pumping rate of the vacuum system, and optimizing peak integration.

Jan 1, 1986

By K. L. Rubow

"IntroductionAir sampling for airborne contaminants requires a system for moving air, a collection method, and a procedure to determine the quantity of contaminant collected. Because occupational exposure limits and air quality standards frequently are expressed in terms of concentrations, a method of determining the volume of air sampled is also needed. The four principal components in a sampling train are shown in Figure 12-1. The inlet admits the air sample into the train; the collector(s) separates the gas, vapor, or particles from the air; the flowmeter measures the rate or total quantity of air sampled; and the pump (air mover) provides the suction required to draw an air sample through the train. Inlet sampling considerations are discussed in Chapter 21. Various types of collectors are described in subsequent chapters. Flowmeters are discussed in Chapter 7.This chapter will describe the air mover portion of the sampling train and air sampling systems that contain three or four components in a convenient package. The chapter consists of two parts. The first part contains a brief description of the different types of air movers and air sampling systems. The second part consists of tables and figures showing detailed information on a wide variety of commercially available air movers and sampling systems. ient size is filled with a liquid in which the suspected contaminant is insoluble. When the liquid is allowed to escape from the vessel, it is replaced by air from the atmosphere to be sampled. Such an air sample is an integrated sample rather than an instantaneous sample because the mass of fluid requires a finite time to empty. In fact, by employing a large vessel with controlled drainage, this method can be used to move air at low flow rates through a sample collector for extended intervals. Additional discussion of this method can be found in Chapter 17."

Dec 1, 1996

By Frank K. McIntosh

Bauxite was first discovered in Tennessee, at Chattanooga, in 1906, during the construction of' the McCallie Street tunnel through Missionary Ridge. Several years later, bauxite was found in sinking a well on the Perry or Isabella Stewart property. These and other deposits furnished a substantial tonnage for the abrasive and chemical industries during the years 1906 to, 1920. The search for domestic sources of war material prompted by World War II brought the Tennessee bauxite deposits to the attention of the Bureau of Mines. During the summer of 1942, James S. Cullison and E. Godwin, geologists of the United states Geological Survey, made a survey of the bauxite deposits of the area. In August 1942, Harold B. Ewoldt, a Bureau of Mines engineer, accompanied by the Geological Survey party visited the area and a drilling program was prepared. Drilling was started in November 1942 and continued until March 1943. A total of 2,519.5 feet in 38 holes was drilled on three properties.

Jan 1, 1949

By J. T. Popp, C. M. McCulloch

This Bureau of Mines study reviews the geological factors that affect methane in the Beckley coalbed in southern West Virginia, including overburden, coalbed structure, type of and changes in lithology above and below the Beckley coalbed, and presence of fractures in the coal and rock adjacent to the Beckley. Depending on the depth, the Beckley coalbed emits from 216 to 520 ft3 of methane per ton of coal mined, and the Bureau estimates that methane emission in a deep, extensively developed mine in this area may exceed 3,000 ft3 per day per ton of coal mined. Average face cleat and butt cleat trends in the Beckley coalbed measured underground are N 33° W and N 53° E, respectively. Close cleat spacing con- tributes to the friable nature of the Beckley and provides easy movement for methane and water. Because rider coals, splits, and carbonaceous shales may contribute methane to mine emissions, predictions of methane emission based on gas content of the Beckley coalbed alone may be conservative. Beckley coalbed reserves in the study area are 234 million tons. The gas content of the Beckley coalbed averages 407 ft3/ton, and the coalbed gas reserves are 108 billion ft3.

Jan 1, 1976

By Robert C. Johnson

Domestic byproduct fluorine (in fluosilicic acid) availability at various price levels of aluminum fluoride were determined and a contingency availability curve developed. The supply of byproduct fluosilicic acid is restricted in amount to certain geographic regions, where plants processing phosphate rock are located, and the byproduct can be collected. The maximum possible U.S. annual supply, based on potential plant capacities, is 373,400 tons of fluosilicic acid containing 295,400 tons of fluorine. Based on inputs of 5, la, 25, 50, and 100 thousand tons per year, five levels of producing aluminum fluoride from fluosilicic acid (100 percent) were costed. Based on a 12-percent discounted cash flow rate, including the cost of salvaging the fluosilicic acid, the calculated selling price of aluminum fluoride ranged from $233 per ton to $448 per ton. At the higher price, 98 percent of the potential supply of byproduct fluosilicic acid could be used profitably; at the lower price only 46 percent could be used profitably.

Jan 1, 1973