Search Documents

By Lloyd A. Morley

A guide to the development and use of an APL computer program for the analysis of load-flow problems is presented. The program is designed to provide an interactive method of load-flow study to improve underground coal mine electrical system design and safety. The theoretical basis for load-flow analysis is discussed, along with per-unit calculations which facilitate computation. Specific input/output, execution and network modification procedures are presented for using the APL program. In addition, typical results are given for examples taken from power system analysis literature.

Jan 1, 1977

By Stewart W. Towle

In 1989, the u.s. Bureau of Mines initiated a contract to gather engineering, operating, and environmental cost data for 1988 for 30 major foreign primary copper smelters in market economy countries. Data were collected for 29 of the designated smelters together with information on applicable environmental regulations. Materials balance data obtained were used with available data for the eight U.S. smelters to determine the approximate extent of copper smelter sulfur emission control in 1988. A broad characterization of the status of sulfur emission control regulation was made. The 37 U.S. and foreign smelters represented roughly 73.2% of world and 89.3% of market economy primary copper production in 1988. The 29 non-U.S. smelters attained 55.3% control of their input sulfur in 1988. Combined with the 90.4% control of U.S. smelters, an aggregate 63.4% sulfur control existed. Roughly 1,951,100 mt of sulfur was emitted from the 37 market economy smelters in 1988. Identifiable SO2 control regulations covered 72.4% of the 29 foreign smelters, representing 66.5% of smelting capacity. Including U.S. smelters, 78.4% of the major market economy smelters were regulated, representing 73.1 % of smelting capacity. Significant changes since 1988 that may increase sulfur emission control are noted.

Jan 1, 1993

By P. G. Guest

Many of the gases and vapors used in anesthesia form explosive mixtures with oxygen or air. Sources of ignition for these mixtures always have existed, in operating and anesthetizing areas. When ether was first introduced, candles and gas-lights and coal stoves caused fires and mild explosions of the vapor-air mixtures. Today the chief causes of ignition are electrical. Fires and explosions are still much too frequent; and, because many of the mixtures are rich in oxygen, the explosions sometimes are very violent. Obvious sources of ignition, such as electric-power sparks and arcs in open motors, switches, and receptacles, as well as exposed incandescent wires and hot plates, usually are recognized by hospital personnel and corrected. A source of ignition that is not so obvious to many is static electricity. Until quite recently the presence of this hazard in a large majority of anesthetizing areas was not even suspected. However, numerous explosions -many of them fatal to patients -have been attributed, with good reason, to sparks from static electricity. In this paper the authors present facts to show the prevalence of static electricity in the average hospital anesthetizing area, and the degree to which this easily developed electrical form of energy constitutes an explosion hazard. An effort is made throughout to explain how static electricity behaves, why it is a hazard, and why certain safety measures are needed and recommended. Following the introduction and a short general discussion of static electricity, which incorporates a glossary of pertinent electrical terms, an account is given of inspections and tests made in a number of hospitals. This account includes many suggestions that should be useful to any person who plans to make similar inspections and tests. However, a comparison of materials and equipment used with those described in the report will reveal, in many cases, the potential dangers and obviate the necessity for tests. The hospital work was supplemented by considerable laboratory research designed to determine the spark energies required to ignite anesthetic-gas mixtures and the exact amount of time involved in developing the usual static charges. The results of this research are reported and the implications examined. The paper concludes with a general discussion of static and related hazards in anesthetizing areas and of the most urgent preventative measures.

Jan 1, 1952

By Mayo D. Hersey

This problem was taken up by the Bureau of Mines as a result of the oxygen explosion at the Jefferson Physical Laboratory of Harvard University , and other similar explosions , in order to supply technical information which would serve as a basis for safety precautions in the future . At the Harvard inquiry the fact was emphasized by the Massachusetts State Chemist , Mr. Walter M. Wedger , that we do not know the limiting pressures and temperatures above which compressed oxygen and lubricating oil are capable of spontaneous explosion . The problem is also of importance to the Army and Navy and to the Bureau of Mines in connection with the hazards incurred in the use of compressed and liquified gases in the repurification of helium. In fact , the risk of fires and explosions due to traces of lubricating oil coming into contact with high pressure oxygen is of serious interest to all concerned with the manufacture and use of oxygen , a commodity which is now being produced and distributed on a rapidly increasing scale . Part of the money expended on this investigation was from Army and Navy funds . The problem was undertaken by the Bureau of Mines at the suggestion of Dr. Charles E. Munroe , Chairman of the Committee on Explosives Investigations of the National Research Council , and referred to the Pittsburgh experiment station of the bureau.

Jul 1, 1923

By John Nagy

Dust explosion data obtained in laboratory tests by the Bureau of Mines are presented for 181 miscellaneous materials that present an explosion hazard. Data are given also for 50 dusts that present primarily a fire hazard and for 88 dusts that did not present an explosion hazard.

Jan 1, 1968

By E. E. Maust

The present work is part of an ongoing Bureau of Mines effort to provide a better understanding of the fundamental phenomena involved in sulfide flotation, the role of oxygen in xanthate adsorption being one essential issue. Galena was chosen as the material around which to develop a conceptual model, partly because of its demonstrated oxygen sensitivity and partly because information on its properties and flotation behavior constitutes the largest part of the fundamental information available on sulfides of commercial importance. The model is formulated primarily in terms of surface electronic energy levels produced by oxygen and xanthate and is further developed using existing experimental evidence and its implications. Four major functions of oxygen are elucidated, and the relationship of these to the formation of lead xanthate, dixanthogen, and a surface compound is discussed. Though yet incomplete, the model provides a useful framework within which the results of diverse experiments can be related to one another in their proper perspective, as shown by a brief discussion and resolution of some apparently discordant results reported in the literature.

Jan 1, 1976

By William P. Harris

The Lincoln Terminal System is described as a device with the capability to deliver technical information, monitor student performance, and assure learning in industrial training. An experimental unit, the LTS-3S, was constructed and delivered to the Bureau of Mines with appropriate lesson material for a test of feasibility and acceptability of this form of training in the mining environment. Operations were conducted at two mine maintenance schools. The overall results were that (1) there was a substantial improvement between tests before and after self-training on the LTS, (2) students found this an acceptable way to learn, and (3) reaction by training personnel and supervisors was favorable toward the feasibility and advantages of using the LTS in the mining environment. Transfer of the LTS to industry depends on availability of reliable units and adequate lesson material. The requirements for authors of training materials were established based on advice from mine training experts, formal analysis of lesson development procedures, and experience from efforts in lesson development at Lincoln Laboratory-It was concluded that experienced mine training instructors were best qualified to proceed effectively and economically to format instructional material for the LTS, if supported by well-designed facilities and services. Discussion with mining experts confirmed the desirability of generating training materials and delivering instruction at distributed locations to meet local training needs and in direct support of industrial operations.

Jan 1, 1975

By Gene Asai

The Bureau of Mines investigated the caustic extraction of alumina and soda from retorted dawsonite-bearing oil shale, as part of a program to devise technology for treating alternative domestic sources of alumina for the production of aluminum metal. Colorado oil shale yielding 13 pct oil (35 gal/ton) and containing 12 wt-pct dawsonite (representing about 4 pct extractable alumina) was retorted to obtain oil-free (spent) shale Spent shale was leached with dilute NaOH to determine the effect of particle size, retorting temperature, leaching variables, and storage conditions on extraction of alumina and soda and dissolution of impurities. Maximum alumina and soda extractions were obtained by promptly leaching minus 28-mesh spent shale, obtained by retorting raw shale at about 5000 C, with 0.5N NaOH. Under these conditions, dissolution of impurities such as Ca, Fe, Ti, and P was low. Leaching tests were made on spent shale stored for periods of up to 30 days at 0° to 42° C and at 0 to 100 pct relative humidity (RH). These tests indicated that significant reductions in alumina extraction would occur if spent shale were stored in ambient Colorado air under naturally fluctuating temperature and humidity.

Jan 1, 1983

By Juel H. Stears

The bureau of Mines analyzed data from 47 coal mine roof-fall resupport accidents that occurred from 1966 through 1974 to identify critical hazards .and problems. These accidents resulted in 62 injuries or fatalities. It was concluded that the majority of the accidents might have been prevented by observance of recommended practices and use of available technology such as setting temporary supports, adequate roof testing, etc. Additional work is needed in the following problem areas where present technology is inadequate: (1) warning of impending roof falls shortly before they occur, (2) better methods of detecting unsafe roof and ribs, (3) providing access to and temporary support of high roofs for testing and bolting, (4) reducing the noise level of stopers, (7) developing temporary roof support; that have greater stability and can be remotely installed, and (6) reducing the number of roof falls through better permanent support.

Jan 1, 1976

By G. S. Rice, H. P. Greenwald, H. C. Howarth

"Stoppings in coal mines serve, important and. vital functions, such as coursing the ventilating current, sealing off abandoned or dangerous workings, sealing fire areas, and separating mines at boundaries. Stoppings may hold back water, but normally that is not their function; their design is, or should be very different from that of a hydraulic dap which is designed to a definite load, often a very heavy one, from one direction over an indefinitely long period. Hence, a dam usually requires an arched structure to resist hydraulic pressure, and it must be massive to meet vertical stresses due to heavy ground pressure.Stoppings are designed primarily to resist a pressure applied laterally through air or gases. Their strength cannot be stated without specifying the direction of applied load. A stopping may be placed in stress by proof pressure subsequent to erection, through extraction of pillars in the vicinity which may act direct, or by squeezing the ribs or heaving the floor. These forces act more or less parallel to the faces of the stopping and may be very great but measures must be taken suitable to each case, and it is impossible to allow for these in general specifications other than to call for normally good construction. A stopping is principally designed to resist the action of forces at right angles to its face, such as the shocks of blasting, the pressure of gas from instantaneous violent out bursts such as have occurred in certain British Columbia coal mines, sudden compression of the air by great falls of roof in closed spaces, and at time pressures that accompany an explosion of either fire damp or coal dust or both. This paper deals with the tests of pressures of explosions only."

Sep 1, 1930

By McHenry Mosier

This paper constitutes the third progress report on a national survey of the use of detachable bits in metal mines. It presents comparative costs of drilling with conventional and detachable bits and describes the operating practice in rock drilling and the reconditioning of drill steel and bits at 10 mines not discussed in previous reports.3/ ACKNOWLEDGMENTS This report has been prepared with the assistance and cooperation of the officials and staff members at the mines visited. Costs and other data at individual mines were developed and furnished by the operators.

Jan 1, 1937

The U.S. Bureau of Mines (USBM) has developed a test procedure to compare the initiating strength of detonators by using adjustable-sensitivity liquid explosives. Various tests of detonator strength are currently used by the industry, but many of them do not quantify the ability of detonators to initiate detonation reactions in an explosive charge. The USBM used mixtures of nitromethane and ethylene diamine, the sensitivity being "fine-tuned" by 2-nitropropane. Military standard J-2, commercial No.6, and commercial No.8 detonators were evaluated using three test configurations: (1) axially immersed in the test explosive, (2) tip just touching surface of the explosive, and (3) immersed transversely in the explosive. Markedly different results were obtained for these three configurations, indicating that the directional effects are important. This explains why different detonator strength tests do not correlate well with each other. Some tests, such as the sand bomb and underwater, measure the total energy out-put, while other tests, such as the plate dent, test measure the energy in the axial direction. The USBM's test data indicate the importance of conducting the experimentation in the manner in which the detonator is actually intended to function.

Jan 1, 2010

By R. G. Warncke, J. H. East, D. Harrington

The mining industry of the United States has long been severely criti- cized because of its high rate of accident occurrence, not only as compared with other industries of the United States but also with the mining industries of other countries, particularly Europe. Statistics, often not strictly com- parable, indicate that the accident-frequency rate in all mining is currently about three times and the accident-severity rate is about seven times as great as the average for general industrial work in the United States. These fig- ures are by no means comforting to humanitarian mining men, irrespective of their status in the industry, and they constitute a challenge that certainly cannot continue to be ignored much longer. The picture becomes much darker when the above statistics are augmented with data indicating that on an exposure basis our mines (more particularly our coal mines) have accident rates two, three, or even more times as great as more or less similar mines in Europe, particularly England, Wales, Belgium, France, and Germany. The sting is alleviated to some extent by the knowledge that our coal mines produce about 4 to 5 times as much coal per man day as is produced in at least some European mines. However, all of these foreign acci- dent statistics should be analyzed carefully before we become very much con- cerned about them, because they are not strictly comparable, for several reasons, not the least of which is the fact that foreign methods of compiling or recording accident statistics often differ materially from ours. Moreover, foreign mining and other conditions are definitely dissimilar to ours in many phases, and numerous other factors affect the comparability of foreign mine- accident statistics with those of the United States. Unquestionably, it should also be taken into consideration that the accident rate of the 140,000,000 or more constituting the populace of the United States as a whole is much higher than that of any other major country in the world and is two, three, or more times the rate of the European countries that have more favor- able mine-accident rates than those of the United States (table 1). Moreover, it is significant that the mine-accident-severity rate of British mines is about six times the average accident-severity rate of the major industries of the British Isles, or but little more favorable than the comparable figures in the United States; namely, that mining has an accident severity rate about seven times the average of about 30 of the major industries of this country.

Apr 1, 1949

By C. J. Hall

Twenty eight pulse release sulfur hexafluoride tracer gas field tests were run in a multi-level multi-vein hard rock mine to measure leakage ventilation. The mine had numerous underground booster fans and gob filled old stoping areas and consequently numerous leakage paths. The tests proved that the equipment and methods developed by the USBM can be used successfully in complicated ventilation circuits. The leakage quantities varied each time a major change was made in the main ventilation circuit. Usually leakage quantities had to be remeasured after a main ventilation change, but measurements could be duplicated for anyone configuration except under certain defined circumstances. The characteristics of an individual leakage path could be determined from the difference between the measured sum of two paths and the calculated characteristics of one of the paths. Many leakage paths could not be evaluated accurately on one shift. Comments are made on equipment performance and field techniques. Programs for the calculation of gas concentrations and recirculation from measured data and for the mechanical integration necessary for a calculated leakage characteristic have been written for an HP 9810 and are included.

Jan 1, 1975

By Louis C. Brichta

The rapid depletion of known deposits of high-grade ore and the need for development of additional reserves, together with increased interest in open-pit mining of low-grade zinc-lead ores in the Tri-State District, led the Bureau of Mines to examine likely mining sites. Underground operations failed to remove all of the ore in a number of areas, and it appeared possible that some of them might be reworked successfully by low-cost open-pit methods. The South Carthage or Hull tract in Jasper County, Mo., was selected by Bureau engineers as favorable for the development of an open-pit mine.

Jan 1, 1949

By A. J. Forney

The hot-gas-recycle process, for the hydrogenation of carbon monoxide, was investigated in a 12-inch-diameter reactor. Initially because the distribution of gas was poor, hotspots developed in the catalyst bed. After the velocity profile of the gas flowing through the bed was studied, the method of packing the catalyst was altered. Because this change improved the distribution of gas, temperature control was excellent. The l2-inch-diameter reactor was operated successfully in the synthesis of gaseous and liquid fuels. When high-Btu gas was synthesized in two stages, parallel-plate assemblies of Raney nickel were almost as active as granular Raney nickel in the second reactor. The pressure drop through the second reactor, however, was reduced 90 percent by the use of these assemblies.

Jan 1, 1962

By James L. Elder

The Bureau of Mines and the Alabama. Power Co. jointly conducted a first experiment in underground gasification of coal at Gorgas, Ala., during the fall and winter of 1946-47. This preliminary experiment showed that it was not difficult to maintain combustion of coal underground, and that coal in place could be completely gasified. It was noted that the high temperature developed by the gasification of coal in place brought about changes in overlying strata that appeared to be favorable to the process. The high temperatures caused the roof rock to become plastic, to expand, and to settle down on the mine floor directly behind the reacting coke face. These results were promising enough to warrant further investigation of the process. It was believed that if this action could be controlled properly with roofs of similar composition, it would tend to force the gas-making fluids underground against the coal faces. Plans for the second experiment were based in part on this favor-able roof action, and the successful operation of the planned initial straightline passages depended on this fact. Gorgas was chosen as the site for the second experiment for the following reasons: A tract of coal land of sufficient size was available and isolated from the main body of coal; the roof rock was similar in composition to that encountered in the first experiment; and the overlying strata were thick enough to eliminate some of the operating difficulties that had been encountered, In addition, power, water, and machine-shop facilities as well as an adequate supply of labor were available in this area, and the friendly cooperation of the Alabama Power Co. further recommended this site for the planned experiment.

Jan 1, 1951

According to industry representatives, U.S. producers were listing unalloyed 95.5 percent aluminum ingot in October at 53-57.5 cents per pound, but reportedly much is being priced at 53 cents. New York dealers raised their October positions by about 3 cents to 56-56.5 cents, mainly to cover spot supply shortages. London Metal Exchange 3-month forward contracts traded up in October from 52.3 to 57.3 cents per pound and closed at 56.4 cents. ASBESTOS The Jaquays Asbestos Corp. has announced the imminent closure of its mine and mill in Globe, Arizona. This is the last asbestos producer in the State having operated continuously, except during the early thirties, since 1914. Cost of compliance with environmental regulations was given as the reason for closure.

Jan 1, 1978

By L. C. IlsLey

"There are two general classes of accidents that prevail in and about mines, namely - (1) those that through the nature of mining work can only be lessened, and (2) those that by proper precaution can be eliminated altogether. Explosive accidents that ordinarily take place while explosives are being transported in and about mines belong to the second class, that is, by proper care all such accidents can in general be avoided.The following table gives a brief summary of several accidents and disasters that have occurred in the United States and indicates the need of universal preventive measures as a basic part of all State regulations.ACCIDENTS AND DISASTERS OCCURRING WHILE TRANSPORTING EXPLOSIVES.***"

Sep 1, 1923

By Arthur V. Petty

The Bureau of Mines has researched the utilization of mining and pro-cessing wastes as raw materials for the production of glass-ceramic pipe. Characterization of various wastes as to occurrence and chemical composition is reported. A computer program was developed and used to identify waste materials and mixes that would result in glass melts from which glass-ceramics could be produced after cooling and subsequent heat treatments. The production of abrasion-resistant pipe from inexpensive and readily available domestic resources could offer an economical substitute for high-alloy steels containing the critical and strategic materials cobalt and chromium.

Jan 1, 1984