Search Documents

By Z X. Zhang

If the iron ore loss is 15% in the process of mining, the total iron ore loss in the world will be about 461 million tons, this is equal to the total production of 230 iron ore mines each of which produces 2 million-tons of iron ore per year. Based on a series of blast tests in the Malmberget mine, this paper shows that ore recovery can be markedly increased by improving blasting technology such as choosing a correct primer position and making use of shock wave collision. The paper further suggests that a high ore recovery can not only reduce natural resource loss and mining cost but also prolong the life of a mine. In addition, the paper shows an example of reducing blast-caused rock damage in the roofs and walls of underground drifts (tunnels) by using new blasting methods in the Malmberget mine. Finally, the paper shows how the Malmberget mine has successfully reduced the ground vibrations, without adversely affecting fragmentation and ore recovery in sublevel caving mining.

Jan 1, 2014

By Alexander Hauck, Dimitri Jung, Uli Leiste

This paper describes results from small scale tests conducted to determine the distribution of impulse on target plates when subjected to loading due to the detonation of a buried mine. The tests were conducted with saturated sand, dry sand, and water as the loading media. Tests were conducted for flat plates and for plates with angled bottoms. Previous testing has shown that angled bottoms can reduce the total vertical impulse delivered to the vehicle significantly. Different stand off distances were investigated as well as loading of the targets both on center and off center. It is very important to know not only the total impulse delivered by a detonating charge but also how this impulse is distributed over the bottom of the vehicle. A complete understanding of specific impulse will permit those parts of the vehicle, taking the greatest amount of loading, to be sized properly. Experimental results were compared to analytical expressions provided by Westine and Tremblay.

Jan 1, 2010

By Ajoy Singh

A study was conducted to investigate the damage potential to underground multi-seam openings caused due to vibration generated by open-pit coal mine blasting. The objective was to recommend optimal explosives weight per delay to be detonated in open-pit blasts to ensure the safety and stability of underground openings. Sixteen blasts with varying charge weights and initiation sequences were conducted at Samleshawari open-pit mine and eighty four blast vibration data were recorded in the Hingir Rampur underground colliery in India. Analysis of vibration data showed that roof of the underground openings vibrated with higher amplitude of vibration compared to pillars and floors. The amplifications of vibration in the roof at the junction were upto 4.3 times the pillar vibration. It was observed that coal chips detached from roof when the peak particle velocity reached 131 mm/s or high. The vibration magnitude recorded was higher in upper seams openings than in below seam openings. Rapid attenuation of vibration was recorded in below-seam openings at similar locations. Appropriate particle-charge weight-distance equations were established to calculate the safe explosive weight per delay to be detonated in open-pit mine for safety of multi-seams workings of underground mine. The support for the galleries and junctions were further modified for the working seams to ensure greater safety.erground Coal Mine

Jan 1, 2012

By Thomas E. Ricketts

Occidental Oil Shale Inc. has spent the last eight years at its Logan Wash. mine near DeBeque, Colorado, developing its modified in-situ oil shale process for obtaining oil from oil shale. Modified in-situ technology involves large underground chambers, or retorts, which are formed by mining out a minimal volume of rock to allow explosive expansion of the surrounding rock into tile mined void volumes. The resulting rubblized retort volume must contain a fairly uniform particle size distribution and void distribution to permit maximum oil recovery during subsequent in-situ processing operations. The more uniform the rubblized volume of particles, the more oil recovery obtained during processing. The processing involves first igniting the top of the retort and then. injecting air into the top of the retort to drive the combustion front downward through the entire rubblized volume. The oil is continuously collected at the bottom of the retort during the processing.

Jan 1, 1981

By G. C. Naveen

Punatsangchu Hydroelectric Project Authority is constructing 1020 MW underground hydroelectric project in Bhutan. The project envisages construction of concrete dam, Desilting Chamber, Head Race Tunnel, Power House Complex and Tail Race Tunnel. Tunneling is one of the major activity in any underground projects as they are driven for multiple activities. By and large the tunnels are a major part of connecting networks from surface to caverns/underground working sites. Many tunnels in hydropower project are part of water conducting systems and one such important tunnel is the Tail Race Tunnel in this project and had to be excavated in thinly foliated rockmass conditions by D&B method. The rockmass is traversed by three to four joint sets and few minor shear seams. Rock Class “Q” values were between III and IV. Tunnel was excavated by full face parallel hole drilling blasting method. The adopted blasting method consisted of drilling 45mm (1.77 inch) diameter holes to a depth of 2m and the drilled holes were charged with 40mm (1.57 inch) diameter cartridge explosives and charges were initiated with half second non electric initiators. The perimeter holes were drilled at closer spacing of 30cm (1 feet) and alternate holes were charged using 32mm (1.23 inch) diameter cartridges explosive. Low dipping foliation joints present in the rockmass tend to slab in crown portion and erratic occurrence of intrusive bodies lead to unpredictable behavior of rock mass posing a major challenge for the safe excavation. Stability was a major issue through controlled blasting under constant supervision too could not limit the overbreak in certain weak rockmass conditions thereby exposing cavities of about 2.5m (8.2 feet). The stabilization of these cavities and handling the overbreak due to rockmass condition was time consuming and warranted additional supports. With systematic measurements and controlled blast designs the Horse Shoe Shaped Tail Race Tunnel of 9.1 m (29.85 feet) diameter and 304m (997.37 feet) length to connect with Downstream Surge Gallery of 314m (1030 feet) length, 18m (59 feet) wide and 58.8m (193 feet) height in thinly foliated and jointed biotite gneiss rockmass was successfully excavated.

By Keith Best

It has been said that when a person does something right no one remembers but when they do something wrong no one forgets. This statement, when applied to the explosives industry, has never been truer. Think about it.How many times have you seen a news crew reporting on how well a blaster is doing his/her job? Normally, all you will see is how bad things are going and how much “damage” is being done.

Jan 1, 2008

By Tony Rorke, Tamara Wiseman

Due to the advancements in technology it becomes easier to obtain accurate measurements for mining, quarry, and construction operations even in the most remote places. The use of off-the-shelf photogrammetric imaging technology and unmanned aerial vehicles (UAVs) are becoming more common in the mining industry for blast design and surveying. Pattern optimization, face profiles, pre and post blast volumetric, stockpile measurements and mine mapping are all areas where these technologies can be used with ease.

Jan 1, 2015

By Chick Kerkering, Stephen Iverson

Perimeter control blasting is common in civil construction projects but not as common in mining. A poorly designed and executed underground mine development blast design can result in unwanted wall rock damage. This damage increases the risk of rock falls and injury. With the availability of good drilling equipment, it is a simple matter to add the few extra holes needed to change conventional drifting into drifting with perimeter control.

Jan 1, 2008

By Norm Disley, Kingsley Hortin, Gertjan Bekkers

As part of the expansion of the Kidd Creek Mine to 2,682 meters (8800 feet) below surface, two largediameter 3000kW (4000HP) booster fans were installed at the 6000 level. Shortly after commissioning the fans, significant damage to the fan bearings were observed, forcing several shutdowns for repairs, which were very disruptive to the mine’s production process.

Jan 1, 2008

By Alastair Torrance, Italo Onederra, Do Sun Kim, Kush Patel, Gary Cavanough

Reactivity of ammonium nitrate-based explosives is associated with the presence of sulphide in the ground reacting with explosive products and in some instances causing spontaneous reactions which can lead to detonation. This paper explains the mechanism of these reactions, the potential cause of spontaneous detonation and how inhibited explosives prevent the reaction

Jan 1, 2019

By Rakesh Raghavaraju, Bibhu Mohanty

Prediction of fracture and fragmentation characteristics of a rock mass subjected to dynamic loads, such as in blasting remains a major technical challenge. The present study is aimed at characterizing the shock transmission properties in controlled experiments in small scale in a well-characterized granitic rock, under varying borehole coupling conditions. Single blast-hole tests were conducted in a granitic rock sample of 145 mm (5.7 inches) diameter and height. The boreholes (in two diameters: 6.4 mm (1/4 inch) or 9.5 mm (3/8 inch)) were loaded with detonating cord of varying charge weight (5.3 g/m or 25 grains/ft to 31.8 g/m or 150 grains/ft of PETN). The effect of explosion gas penetration into the target rock was eliminated by inserting a thin-walled copper liner along the borehole wall. Embedded carbon composite resisters were employed at varying distances from the borehole to measure transmitted shock pressure for two coupling conditions (i.e. air and water) at distances of 1x to 9x the borehole diameter. The paper analyzes the decay of shock pressure as a function of distance from the borehole, and its implication on shock-induced fracture properties of the target rock as the first step in predicting fracture and fragmentation behaviour in a well-characterized rock.

By Michael S. Wieland

"This report investigates whether it is tractable and thereupon reasonable to remove the boosterinfluences when ranking the toxic fumes of non-cap-sensitive mining explosives. The hazard potential is represented by relative fume toxicity RFT, the resultant influence computed from a formulated rule with a restricted set (tally) of fume components and multiplying constants. The RFT result is compared to the rule criterion that represents the worst case tolerable toxicity stipulated by regulations or otherwise. The typical nonstoichiometric booster composition can render notable unwanted influence on the RFT ranking results. Historically, the remedy was to shoot the booster separately and reduce the trial concentrations by the relevant subtractions. Unreal negative concentration results were noted on rare occasions, revealing the faulty nature of the reduction procedure. With thermodynamic reaction chemistry codes TDRC, on the other hand, the booster ingredients can be retained in or removed from the reactant tabulation, yielding reduction factors taken as the concentration ratios for the two circumstances. The underlying presumption regarding reduction factors is that the ratios of component concentrations with and without the booster ingredients when resolved theoretically ought to equal those rendered experimentally, when tractable. Upon rearranging the presumed relationship, the unadjusted fume concentrations divided by theoretical reduction factors yield the wanted readjusted fume concentrations, thereby removing the booster influence without generating unreal negative concentrations."

Jan 1, 1999

By S. Lim, G. Walsh, V. Romero

The cable television show, Mythbusters, contacted the New Mexico Institute of Mining and Technology requesting a pressure gauge to be used in underwater testing. The requirements for the gauge were: it must be passive (i.e. require no power to function), it must indicate when a certain, pre-determined pressure was reached, and that indication was to be visual. A pressure gauge was developed, using standard, commercially available rupture discs, set to burst at 500 psi. Underwater testing was conducted using a 400 lb Pentolite charge. Test devices were set out at ranges from 50 to 200 feet from the seat of the blast. The rupture discs showed a lethal range up to 100 feet, but not at 150 feet. This result matched well with the behavior predicted through modeling and simple shock physics calculations. Additionally, the geometry between the incoming shock and the pressure gauge did not seem to have a strong effect on gauge performance.

Jan 1, 2009

By Jason Baird, Philip Mulligan, Caleb Baumgart

This report details the pressure variances, measured at four pressure sensors placed equidistant from the center of an airburst explosion, as the blast pressure from a single charge expands radially. Many of the empirically derived equations used for predicting the blast pressures of an explosion, assume a point source detonation and that the radial pressure expansion is equal. The authors understand that the equations used to approximate the blast pressure may not have 100 percent agreement with the observed pressure. However, during previous research at Missouri University of Science and Technology (Missouri S&T) the pressure variances had a range of 1,200 psi, between the four pressure sensors placed two feet from the center of a 1/2-pound (226.8 gram) of hand packed C4. The variances indicated that at the close distance from a suspended explosive charge the pressure does not behave as that observed from a point source.

Jan 1, 2014

By Kris Shukla

Noise and vibration produced by blasting generate curiosity and concern from neighbors. Experiments conducted in Sweden, Canada and U.S.A. have established that fine cracks in the plaster--the weakest part of building components--appear at a particle velocity of 4.0" per second or more. Taking into account the margin of safety, the safe zone criteria of 2.0" per second has been established.

Jan 1, 1978

By Klaus G. Hinzen

Seismic observations offer the only possibility for remote sensing of physical processes like shock-front spreading, material crushing and ground movement. A better understanding of these processes will help to increase the economy of blasting. We developed a digital seismic monitoring system for research purposes. The system can simultaneously record up to 64 channels with a maximum sampling rate of 31 kHz per channel. A software package for rigorous analysis of blast induced seismic waves has been developed.

Jan 1, 1989

By Larry Ng, Keith McDonald

The benefits of controlled blasting techniques have gained increasing recognition by the mining industry in recent years. The utilization of an effective controlled blasting programme can result in a safe work environment with less loose rock and a reduced level of scaling and ground support.

Jan 1, 1994

By John Floyd, Larry Wardrip

A series of tests were conducted to evaluate the performance of a high density, high velocity cartridged explosive. The tests included two production blasts in a limestone quarry and two production blasts in a granite quarry. To quantify blast and product performance, each blast was monitored with the following equipment: l Two (16mm (Lo Cam) high speed cameras (500 images per second) l Velocity of detonation recorder (I million samples per second) l Four face motion accelerometers (1 million samples per second) l Digital seismograph The fragmentation distribution produced by each blast was quantified with digital image analysis The benefits of the use of high velocity, high density toe loading was quantified in terms of: l Vibration reduction l Fragmentation improvement l Excavator performance In addition to the field tests, a comprehensive evaluation was performed to determine the cost/benefit relationship of the use of the toe load. This paper will include the findings of the study along with guidelines for use in other quarry operations.

Jan 1, 2002

By Stephen G. Rieben

Almost everyone has at least heard of the two one-call systems which serve New England. They are "Call Before You Dig", which covers Connecticut, and "Dig Safe", which covers the remaining five New England states. Those of you who are more familiar with these programs know that it is our job to help guard against the accidental dig-ups of buried plant and to prevent facility service disruptions. We cover all types of buried facilities, from cable television to high pressure gas transmissions lines, telephone cables, electric facilities, fiber optics and everything in between

Jan 1, 1990

By Catherine T. Aimone-Martin, Kristen Kolden

In August of 2013 the USDA Forest Service (USFS) blasted bedrock at the base of a waterfall in Kanalku Creek within the Kootznoowoo Wilderness Area on Admiralty Island in the Tongass National Forest located in Southeast Alaska. The purpose of the blasting was to widen and deepen a plunge pool at the base of a waterfall complex considered to be a partial barrier to migrating sockeye salmon. Drilling and blasting to remove 12 to 15 cubic yards of rock occurred over a two day period.

Jan 1, 2015