Search Documents

By Ian Bell

This paper investigates fragmentation in an aggregate quarry using the fragmentation-energy fan concept. Six blasts were monitored, located one behind the other in the same quarry area. The rock structure was blocky, the water level and the usage of explosives were variable within and between the blasts. The powder factor above grade was between 0.28 and 0.44 kg/m3 (0.47 and 0.74 lb/yd3). Fragmentation of the plant feed was measured using an online digital image analysis system and three belt scales. The oversize material that was not directly fed to the plant after the blast corresponds to 3‒9.3 % of the total. Data from image analysis was used to build the size distribution in the coarse range (fragments above 120 mm), and the passing fractions at 120 and 25 mm (4.72 and 0.98 in) obtained from belt scales data were used in the range 120‒25 mm (4.72 ‒ 0.98 in) . The non-dimensional percentile sizes between 10 and 90 % for each blast are described through power functions of the powder factor above grade; the model coefficients are statistically significant. From them, using the principles of the fragmentation-energy fan and the Swebrec distribution properties, the fragmentation can be expressed in terms of the powder factor by means of five parameters: the fan focus coordinates and the three parameters of a function of the exponents vs. the percentage passing. The model shows a good capability to describe fragmentation.

Jan 1, 2019

By Tyler Rockley, Cara Rosen

Blasting at a granite quarry in eastern Maryland produces elevated air blast readings that can fall into the cautionary zone for the state of Maryland environmental regulations on a semi-regular basis. When designing blast patterns in this quarry, challenging geology creates rough and uneven blast faces that can be difficult to capture with 2D laser profiling fully. Utilizing several methods known to manage high air blast results like pattern adjustments, decking, and timing changes have not achieved consistent outcomes.

Feb 1, 2020

By Dale Preece, Steven Case, Cassidy McAllister

Simplot Phosphates produces high quality phosphate fertilizer through open pit mining. The operation near Vernal, UT began as a three-pass mining process carried out with drill and blast followed by the combined effort of shovel-truck and dozer material removal. The first two passes removed the overburden and the final pass mined the relatively hard phosphate ore for processing at the mill. Vertical blastholes were employed in all of the mining passes.

Jan 1, 2012

By Tyler Rockley, Cara Rosen

Blasting at a granite quarry in eastern Maryland produces elevated air blast readings that can fall into the cautionary zone for the state of Maryland environmental regulations on a semi-regular basis. When designing blast patterns in this quarry, challenging geology creates rough and uneven blast faces that can be difficult to capture with 2D laser profiling fully. Utilizing several methods known to manage high air blast results like pattern adjustments, decking, and timing changes have not achieved consistent outcomes. Accurately capturing and modeling this geology is the key to controlling high air blast. 3D modeling and profiling by drone is the solution to understanding accurate face profiles and real minimum burdens. Using 18 months of blasting data and air blast results to establish a baseline, the comparisons between blasts designed with 2D profiling and blasts designed with drone 3D profiling show improvement in air blast levels. Additionally, shots with completed drilling were drone profiled to understand precise amounts of burden for each borehole. This 'audit' of a blast allows for custom loading of explosives, accommodating the amount of burden present on the blast face. 3Dprofiling is not a new tool in the blasting industry, but a drone alleviates some of the restrictions ground systems face. Controlling and managing air blast, as it pertains to face burdens, requires an understanding of those burdens from all angles. A drone provides that distinct level of insight. The results of this study indicate that drone profiling is managing the customer's air blast readings, allowing the customer to maintain their license to operate within the community.

By Paul McAnuff, Alastair Grogan

In Canada, the only vibration regulations which apply across the entire country are intended to protect fish spawning areas. The Provinces and Territories regulate mines and quarries, and are responsible for setting vibration and airblast regulations. Some Provinces have set specific regulations, while others leave these restrictions to the mines inspectors who can set limits on a case by case basis. For the most part, it is left to individual municipalities to regulate blast vibrations and airblast from other blasting activities, which differ from jurisdiction to jurisdiction, and in some cases are not enforced. Blasters working in different jurisdictions have to be aware of the applicable regulations for the area they are working.

Jan 1, 2005

By Drew Martin

In March 2010 the Boral Linwood Quarry, Adelaide South Australia, implemented the blasting contractors Monte Carlo Blast Vibration Model as part of their blast design process. The Linwood Quarry was developing an area where blasting activities were marginally complying with the statutory vibration limits. Compliance to the statutory limits was only being achieved through the use of small blasts (less than 15 000 T (14 763 ton)) at a high cost to the quarry.

Jan 1, 2012

By Peter Dare-Bryan, Will Hunt, Lee Julian

It is well-known that blasting has an economic effect on grade control activities. However, until recently, methods did not exist for measuring the grade control value change caused by the blast. Rules of thumb were the best method to minimize ore loss and dilution, as simulation has been traditionally constrained by time and computer power. Even with these rules followed, an extensive study performed on over 150 blasts showed that the value change caused by the blasts followed a normal distribution – some blasts created value, and some blasts destroyed value. The question naturally asked was “How can we ensure the blast designs are optimized to create value?” Recent advancements in computer power have enabled real-time blasting simulations that create post-blast grade control models before the blast is fired. Understanding what will happen before it happens allows blasters and grade control personnel to iterate designs, searching for the highest value achievable.

Feb 6, 2023

By N. Skopak, W. Birch, A. Douglas, C. Johnson

Determining the origins of air overpressure has been a long-debated topic within the explosives engineering community. Historically, it has been accepted that the initial face movement gave rise to air displacement, resulting in an air overpressure pulse. Later research proposed that the air overpressure pulse resulted from the shockwave rapidly propagating through and impacting the quarry face. Most recently, researchers have derived that air overpressure is associated with the gas phase from which a gaseous product from explosives rapidly pours out the quarry face under high pressure. Significant research has strongly indicated that the time at which the air overpressure pulse exits the face fails to coincide with either the arrival of the shockwave at the free face or the initial face movement. Research has consistently shown that the shockwave arrival at the face occurs before the air overpressure pulse leaves the face. Therefore, to best determine which blast mechanism contributed to the initial air overpressure pulse, testing was aimed at verifying the precise time at which the air overpressure exited the faces compared to when the face first moved. This research describes tests using scaled concrete blocks, which provided the ability to control the key parameters necessary for the research to be successfully concluded. Black powder was selected as the energetic material to eliminate the production of the detonation wave while still inducing other gas-producing effects. The components evaluated were air blast arrival times in front of the face, the initial movement of the blast face, the precise initiation time of the blast hole, timing of pressurization within the rock mass (between borehole and face, or adjacent borehole), and the speed of sound in the air. A detailed timeline was created which portrays the actions within the blast to promote an understanding of the sequencing of events. The results showed that the initial face movement occurred at 17.57 milliseconds (ms) while the calculated time at which the air overpressure exited the face occurred at 7.07 ms. The large disparity continues to reaffirm the premise that the origin fails to coincide with the air pressure pulse. Average pressurization through the block occurred at a rate of 341.23 feet per second (104.15 meters per second) which resulted in the gas release pulse being calculated to exit the face between 4.41 and 6.21 ms. This pulse correlates more accurately with the air overpressure origin timing which will be the focus of continued research. Knowing the precise origin of blast-induced air overpressure will assist in being able to better control it through appropriate blast design.

Jan 1, 2024

By Lizbeth A. Escobar, Phol M. Llanos, Maritza Y. Avila

The present research develops the estimation of critical parameters such as the distances and times between holes to avoid failure due to dynamic pressure in electronic detonators based on the near-field ground vibration model of Holmberg & Persson and the hydrodynamic model of Neyman.

Feb 1, 2020

By Weiying Zeng, Shouwei Wang, Jinbei Zhong, Xiangdong Meng, Lingtian Meng

"Due to a drainage problem, the Lanzhou to Chongqing high-speed rail line had been out of service during the 2015 wet season, so a drainage tunnel is to be constructed for the line and required to be accomplished before the 2016 wet season. This drainage tunnel is only 5 meters below the line which is in service, therefore blasting vibration needs to be strictly controlled. This paper introduces all theapplied blasting methods, parameters and detonation throughout the entire project, finally bringing in the electronic detonator stagger phase technique and corresponding time difference for detonation."

Jan 1, 2017

By Michelle Crull, Susan Hamilton

Explosives safety requirements in the United States began in 1909 when the American Railroad Institute questioned explosives manufacturers regarding distances necessary to protect employees and property. In response to this inquiry, a group of explosives manufacturers collaborated to study over 200 explosive accidents. This study resulted in the 1914 American Table of Distance (ATD) published by the Institute of Makers of Explosives (IME). The 1914 ATD provided suggested separations between explosives and inhabited buildings, public highways, and public railways.

Jan 1, 2010

By Viktor Aranovich, Thomas E. Brown

The Almalyk Integrated Mining and Metallurgical Plant is located near Tashkant in Uzbekistan and is one of the former Soviet Union's largest copper producers. Almalyk consumes about 10,000 metric tonnes of explosives annually and expects this requirement to double by the end of the century as they implement a program to boost mine output.

Jan 1, 1998

By Lynn Long

We have seen many new developments in the explosive and blasting accessory category, but one of the most useful items is the blast control plug. Blast control plugs are cone shaped units that are placed in the stemming just above the explosive load. They are placed about 8 to 12 inches up into the stemming material.

Jan 1, 1996

By Tyler Rockley, J. P. Remi Proulx, Ruilin Yang

A highwall blast vibration project was carried out to quantify the level of blast vibrations produced from a trim blast in soft rock and a combined production and trim blast in hard rock. Combining production and trim blasts could be performed without exceeding the mine’s vibration limits.

Feb 1, 2020

By T Duff

This paper describes results from small scale tests conducted to determine the distribution of pressure on target plates when subjected to loading due to the detonation of a buried mine in various media. The tests are conducted by using saturated sand, dry sand, and water as the loading media. Different stand-off distances are investigated. Kolsky bars and pressure sensors are used to determine the free-field pressure - time profile of the output of the charge at any location on the vehicle bottom. For verification of the pressure results at certain distances, the specific impulse measured by utilizing different size round plates are employed. In order to investigate the loading mechanisms, high speed cameras are applied. The small-scale test results can be scaled to full scale by using verified scaling laws.

Jan 1, 2014

By Gustavo Huerta Valer, Jorge Cárdenas Miranda, Johan Salas Flores

One of the challenges of mining is the optimization of the blasting process, which has an important impact downstream in the processing of crushed ore in the plant, that is why mining companies ensure the results of granulometry obtained from the blasting process through a joint work with companies specialized in the process of loading with explosives.

Feb 6, 2023

By Adrian J. Moore, Alan B. Richards

Responsible blasting requires that rock throw be controlled to ensure that no danger will result to people and property. This paper describes the development and testing of empirical field calibrated formulae that can be used to evaluate rock throw, provide an early warning of when reduced burden will endanger people and property, and prevent flyrock incidents. Inputs to the formulae are charge mass, burden or stemming height, and a site constant that lies within a general range that can be tightened by site calibration. The output is the distance that rock will be thrown, and this ‘design your own flyrock’ quantification can be used to establish both safe clearance distances, and the critical range of burdens and stemming heights where the situation changes rapidly from safe to hazardous. Examples are given of the use of the model to control flyrock in open-pit mining and quarry operations, in situations which are controlled by both burden and stemming height.

Jan 1, 2004

By S. Hosein, W. Birch, C. Johnson

The widespread adoption of electronic detonators has given rise to the development of linear superposition to control the environmental impact on both third-party properties and residents resulting from blast induced vibrations. Linear superposition has become a very effective tool in the hands of blasting engineers and has enabled aggregate reserves to be accessed that once had to be abandoned. This in turn has resulted in more and more complex blasting pattern to be developed that contain multiple rows and multiple decks all with different maximum instantaneous charge weights of explosives. This is then made more complex by having to consider multiple sensitive locations often with different Peak Particle Velocity vibration limits. This paper is a case study of what did happen when a blast was designed that “pushed the boundaries” of environmental blast vibration design and control, without taking fully into account the fundamental geophysical properties of seismic waves. The resulting blast design caused a greatly enhanced s-wave to be created in a critical direction from the blast pattern. The root cause being the s-waves from earlier detonating decks in the blast pattern arriving within 2 milliseconds of decks detonating later in the blast pattern. 209 individual decks were fired in the blast pattern of which 41 pairs of decks arrived at the observation location less than 2 milliseconds apart when taking into account the s-wave speed and direction. The lesson to be learned when using electronic detonators to limit ground vibrations from complex blasting patterns, is that it is just not good enough to look at the planned firing times, a professional blasting engineer must also understand the likely interaction of the various seismic wave types created and their combined impact on any given monitoring location.

Jan 1, 2024

By M. S. Dotto

The knowledge of the explosive/ rock mass interaction process is important in predicting blast performance. It includes understanding rock properties, energy usage, and attenuation in the rock mass. The paper proposes a method to quantify blast-induced rock mass damage from the field measurements and apply it to modeling blast fragmentation.

Feb 1, 2020

By Ray Slavin, Remi Proulx

The Meikle Mine is a mature underground gold mine utilizing primary and secondary longhole open stoping method with delayed backfill. Combined production with the newly developed Rodeo Mine is 4700 tons per day (4265 tonnes per day) of ore. The vast majority of Meikle Mine production comes from secondary and remnant stope blocks. Remnant stopes are ore blocks that were left behind in the initial mining sequence due to various reasons. Mining of these remnant blocks has created many challenging blasting situations. The application of electronic initiation to blast remnant stopes has proven extremely beneficial. Electronic initiation has provided the blasting engineer with a high degree of flexibility with respect to timing to successfully extract these difficult stopes. Post blast assessment of the remnant stopes using the mine’s cavity monitoring system (CMS) demonstrates that the mine is maximizing ore recovery and minimizing waste dilution. The largest remnant stope blast to date required 54 holes and produced 6700 tons (6075 tonnes) of ore. Another area where the application of electronic detonators has proved successful is in the extraction of slots in which ground conditions are extremely poor. Taking the slot blasts in one shot with double-decked holes as opposed to two single-decked shots has eliminated the need to clean and or re-drill holes. The ability to open the slots in one blast has helped reduce the total mining cost. This concept has recently been expanded to blast complete stopes in one shot. This reduces the stope cycle time considerably and allows the mine to bring ore forward. Current plans for 2004 are to excavate 50% of mine wide stope production using electronic initiation technology.

Jan 1, 2004