Search Documents

By J. Kuipers, R. W. Lawrence, P. B. Marchant, W. Brooks, J. T. Chapman

"Bioleach testing and piloting was conducted on refractory gold sulphide concentrate from Austin Gold Venture in Nevada during 1988. The objective of the test programme was to determine the technical and commercial viability of bioleaching as a concentrate pretreatment step prior to gold extraction by cyanidation. Baseline CIL cyanidation typically resulted in < 20% gold extraction from the Austin concentrate. Bioleaching enhanced gold extraction up to 95% using conventional CIL techniques. This paper summarizes the bioleach test programme and results, including pilot plant studies onsite, and describes the commercial design details for a possible retrofit of the Austin flotation tailings leach circuit to accommodate 20 tpd and 40 tpd capacity concentrate bioleach facilities.INTRODUCTIONBioleach testing on a refractory carbonaceous sulphide concentrate from Austin Gold Venture (AGV), was initiated in late 1987 as part of an ongoing programme at Austin to investigate alternatives to concentrate smelting. Preliminary batch biooxidation tests at Coastech indicated that over 90% gold extraction by carbon-in-leach (CIL) cyanidation of the bioleach residue could be achieved, compared with less than 20% gold extraction on untreated concentrate by similar CIL processing.Subsequently, a more rigorous laboratory study was undertaken at Coastech to establish continuous biooxidation operating criteria on a bench scale. The objective of continuous testing in the laboratory was to provide confirmation of enhanced CIL response based on continuous bioleach products and to determine key process operating and design parameters for pilot testing. The success of the laboratory test program led to the installation of a mobile pilot plant at Austin Gold Venture. The plant was operated by Coastech and AGV during 1988 to provide scaleup data and design criteria for commercial design and feasibility analysis. Based on pilot plant operating data, a detailed commercial bioleach plant was designed as a possible retrofit to the existing 1000 tpd CIL plant. Capital and operating costs were estimated to provide a commercial feasibility study of bioleaching as an oxidative pretreatment for Austin refractory concentrate."

Jan 1, 1989

By Vic Casaletto

"IntroductionThe Canadian mining industry is under immense pressure to compete with foreign mine operations. The very survival of the Canadian mining industry is threatened by lower ore grades, environmental pressures, high cost of labour, unfriendly tax laws toward exploration and the increasing cost of new technology. In order to compete in the world market, Canadian producers and their suppliers are rethinking age old customer-supplier relationships in favour of preferred supplier relationships which can improve the profitability and enhance the competitive position of both partners.This paper attempts to redefine partnerships with suppliers in the context of a ""win-win"" objective. It will outline the measurable benefits to both partners through a representative product which highlights the keynote structure of any successful supplier partnership The Status Quo...Mines all over North America are plagued with the same recurring questions, ""Who has the best product for my operation at the lowest price... How do we know a product will perform to a supplier&apos;s projections after the sale...What do we do if the product fails to perform as expected?"" These questions have been asked by underground mining operators for decades but rarely have long-term solutions with measurable results been achieved.The LHD industry is one example of the status quo where partnerships will provide large gains toward technological advancement, reducing mobile equipment costs. The underground mining industry is out of sync with their surface counterparts in the open pit business.Partnerships with suppliers in the open pit world are not only a standard practice but a culture which has existed for decades. Open pit operators enjoy concepts which fix their mobile equipment costs for the life of the mine and hold the equipment supplier accountable for performance and fleet economics for 60 000 service hours and longer.Manufacturers are attempting to transfer this culture into the underground mining industry. Figure I illustrates the significance of a capital driven decision."

Jan 1, 1994

By J. Spross

"The Key Lake mill has operated since the fall of 1983. The ore from both Key Lake open pits will be depleted by 1997. It is planned to use this mill, located about 60 km southwest of McArthur, to process the McArthur River ore.While the geological data collected so far on the McArthur deposit are encouraging, more information of the deposit is needed before any detailed mine planning can begin.The surface drilling program identified the orebody and provided information on the geomechanical and hydrological properties of the overlying sandstone. It was proposed to conduct an underground exploration program to further delineate the orebody. This was air proved following a public hearing and review process. This program involves the sinking of a 630 metre deep shaft and the driving of one or two drifts along a portion of the orebody. From these drifts, exploration drilling every 10 m to 15 m through the orebody will provide the information required for the preparation of a feasibility study and an Environmental Impact Statement (EIS)."

Jan 1, 1994

By T. C. Chudy, C. C. Hamilton, G. R. Lane

The selection and provision of mineralogical services to assist in developing a GeoMetallurgical program for a Cu Porphyry Mine in South America is covered in this paper and presentation. The objectives of the study were to provide a rapid mineralogical scoping protocol to support and confirm results of sequential Cu leach data and to provide detailed mineralogical analysis of four composites and products on which locked cycle test-work were performed. Results showed good reconciliation was achieved between measured chalcopyrite and secondary Cu mineral contents with leach data using a linear intercept mineralogical procedure by TIMA (Tescan Integrated Mineral Analyser), as well as a generally positive correlation between pyrite and Cu-sulphide grain size. Size-by-size analysis of Composite feeds and test products was used to outline comparisons between feeds on a mineralogical basis and provide liberation and association data with which to diagnose and better explain performance. Identifying key mineralogical drivers to Cu recovery and concentrate grades using these results, a greater understanding of the role of chalcocite and pyrite on metallurgical performance was established. INTRODUCTION As a global supply of copper, porphyry copper deposits are typically very large, often in excess of a billion tons of ore (Keeney, Walters, & Kojovic, 2011; McMillan & Panteleyev, 1980) with grades typically between 0.2 and 1.2% Cu, and up to 2% Cu in places. They are also a source of gold. The complexity of copper porphyries arises from their classically zoned nature, the type of host rock, as well as whether or not they have been overprinted by oxidation, weathering and supergene enrichment (Sillitoe, 2011). Zones of alteration and other geological attributes give rise to varied mineralogy, ore mineral textures and material properties, all of which result in different processing characteristics. Due to the interdependencies of geological and processing characteristics, it is vital to study links between the geology at the macro-scale and mineralogical features down to millimeter and micrometer scale (mineral content and texture) and their influences on mineral processing behaviour (Cropp, Goodall, & Bradshaw, 2013). The growing field of GeoMetallurgy aims to provide an Orebody Knowledge framework by which to gather such information as it pertains to: (1) Understanding and predicting likely flotation response; (2) Guiding relevant test work to investigate and validate links, interdependencies, theories and data interpretation/evaluation; (3) Populate a block model with relevant information and; (4) Implement and refine the model for ongoing optimization and control. Specific questions addressed by using mineralogy often include flotation diagnostics as aids to interpretation, causes of dilution and losses to tailings, as well as guidance to sampling for test work (Cropp et al., 2013).

Jan 1, 2019

By Song (Bruce) Li

This paper presents a three-tier web-based GIS application that uses Java Server Page (JSP), Java Servlet and relational database to manage performance monitoring and reporting in the oil sands mining industry. It is a real-time Earth Structure Performance Monitoring System (ESPMS), which allows the user to record and store instrumentation monitoring readings as well as technical observations and instrumentation installation documentations into a complete relational database. The ESPMS introduces the advantages of precise field record keeping, due diligence, security, consistency and completeness while at the same time simplifying the task of reporting. ESPMS combines web-based Geographic Information System (GIS) mapping and data management to facilitate the collection, organization, retrieval, reporting and communication of the vast amounts of monitoring data related to mining and tailings engineering associated with site investigation and construction information. ESPMS utilizes web-based GIS technology to incorporate referenced aerial photographs, Energy, Mines and Resources (EMR) maps or AutoCAD drawings as a base map for the monitoring site. It dynamically creates and administers all instrumentation monitoring locations and reading frequencies. It enables the user to collect and manage the data associated with an unlimited number of reading events. It provides the designer with real-time monitoring data (what, why, when, how), thereby allowing them to make early adjustments to design protocols or procedures, or to take remedial action(s) regarding the subject earth structure under construction or after completion. It provides more cost-effective reporting and data sharing through the Internet. It improves security on data entry and eliminates unauthorized data changes. It allows better integration of graphics and illustrations with numerical data files. It is capable of managing the continually expanding workload resulting from new and larger structures in the oil sands or other mineral mining industries. The ESPMS facilitates easier data gathering for preparation of as-built and after-built or regulatory reports, etc. It enables quick location of the interested instruments and summarization of the performance of the instruments. It enables one to visualize performance data and QA/QC construction test results spatially on any given cross-section. Data can be exported to MS Excel for detailed analysis and to evaluate the stability of the earth structures.

May 1, 2004

By C. Bazin

"Discrete transfer functions which use the grinding circuit feed tonnage to predict mass flowrates at reagent addition points in the flotation circuit were calibrated using a dynamic grinding/flotation simulator. Predicted values are multiplied by g/t ratios to calibrate reagent flow. The transfer functions are currently integrated into the distributed control system at Les Mines Selbaie.INTRODUCTIONThe development of adequate tools for the control of flotation processes is a continuous challenge. Since the early 1970's there have been numerous publications dealing with practical applications of flotation process control. A review of that literature shows that basic feedback and feedforward controls are the two preferred strategies for flotation processes. Some advanced control schemes started to emerge (e.g. Zaragoza and Herbst, 1988). Feedforward and feedback aim at reducing the effect of the following flotation process disturbances (e.g. McKee, 1991):0 Changes in throughput;0 Changes in feed grade;0 Changes in particle floatability (size, liberation, surface oxidation ... );0 Deliberate changes of set-point;Feedforward strategy acts on manipulated variables, mainly reagent addition, to attenuate the effect of disturbances such as changes of feed rate and grade. The feedforward strategy is driven by measurements of disturbances. Feedback control acts to compensate unmeasured disturbances, such as ore floatability, and to bring process variables to targeted set-points of concentrate or tails grades. The feedback control action is driven by set-point error, caused by either a deliberate change of set-point or unaccounted disturbances.This paper proposes a way to improve feedforward control schemes by addition of a simple model of solids transportation. The feedforward strategy considered in this paper is of ratio type, i.e. the manipulated variable is changed according to a predefined ratio between this variable and the measured disturbances. A typical example is the ratioed reagent addition to mass flow of ore."

Jan 1, 1993

By Nadarajah Nanthananthan

Mine backfill has been widely used as a means of ground support. While proper design of backfill is important to ensure ground stability, understanding the failure mechanism and the various influencing factors in a filled block is essential. This paper presents a modified sliding failure model of a confined backfill block. The model considers both the gravity load of the backfill itself and the overlying load from fragmented ore or backfill on the top. A series of new equations were derived and the relationships between factors such as factor of safety, friction angle, cohesion and the exposed stope height were developed. This modified model will be a very useful tool in backfill design, for example, to optimize the design of backfill for a given stope geometry or to determine the maximum backfill height for a particular type of backfill.

May 1, 2007

By P. J. van Staden

Several differences exist between the columns used for laboratory simulations of heap leaching and commercial heaps. Column walls support part of the weight of the ore and restrict the particle packing arrangements. Columns are typically of a diameter that is smaller than the dripper spacing to be used on the commercial heaps. The stacking practices that cause segregation and stratification on heaps are absent from columns. Intuitively, these physical differences would be expected to be the reasons behind the observed differences between column and heap leaching performance. But how can they be quantified, and what is the magnitude of the differences? Could some of these differences be built into column leaching experiments in order to better simulate commercial-scale heap leaching performance to ease the scale-up calculations from column leaching data? Alternatively, could heap construction practices be improved so that the ideal performance obtained in columns could be emulated on heaps? Data from a few heap leaching cases studies that permit direct comparisons between column and heap leaching performance is analysed, to reveal the extent of the differences in resistance to mass transfer. Discussion is provided on the implications for column and heap leaching practice, and for scale-up design procedures. INTRODUCTION Differences have been known to exist between leaching performance observed in laboratory columns and that of commercial-scale heaps. Both the heap leaching kinetics and finally achievable extent of extraction are generally found to be inferior in heaps compared to that achieved in columns. Heap leaching design engineers extrapolate the anticipated heap leaching performance by multiplying the time-axis of a column-leaching curve by a factor of about 2 and the extraction-axis by a factor of about 0.8, as explained by Jansen and Taylor (2002), Scheffel (2002), John (2011) and Scheffel, Guzmán, and Dreier (2016). The procedure is illustrated in Figure 1 by means of a hypothetical example. The solid line represents the leaching performance observed in a laboratory column, and the dashed line represents the anticipated leaching performance of a heap, extrapolated from the column leaching data using these empirical scale-up factors.

Jan 1, 2019

By Xuanxue Mo, Kaihui Yang

"The Laochang mine, located in the Sanjiang area of southwestern Yunnan Province of China, is a volcanogenic massive Pb-Zn-Cu sulfide deposit. It is hosted by a pyroclastic sequence of Early Carboniferous age, namely the lower member of the Yiliu Group, which was intruded by syenite and rhyolite porphyry. The volcanic suite is basaltic or basaltic-andesitic in composition, has alkaline affInities, and is associated with the initial rifting along the margin of the Baoshan-Shanstate continental microplate (Yang, 1989). The ores are typically Pb>Zn>Cu in composition, averaging 3.820/0 Pb, 3.51% Zn, from 0.01% to 1.85% Cu (0.107% av.), a high average content of Ag (113 glt) and recoverable amounts of Au, n, Gd, Ga, Ge, In. A massive sulfide zone, in which lenticular and stratiform orebodies are localized in a sulfide-<:arbonate-silica shale unit or sulfidic tuffIte horizon that usually overlies coarse-grained pyroclastic rocks, is underlain by a stringer sulfide zone developed in a subvolcanic intrusion or volcanic sequence. The sulfIde mineral assemblages, from the top to the bottom of the deposit, are: realgar + orpiment - galena + sphalerite + pyrite - chalcopyrite + pyrite + pyrrhotite + arsenopyrite. Oxide and sulfate minerals occur rarely in the massive ores. The massive ores are generally fme-grained and banded, but coarse-grained ore, colloform and framboidal texture, and growth-zoned pyrite and sphalerite are common. Sedimentary features such as graded bedding, brecciated and deformed ore clasts, and chaotically emplaced blocks, are well preserved, indicating that the massive orebodies have undergone slumping and displacement. Alteration is weak in the hanging-wall rocks, but strong in the stringer zone. Two distinctive alteration zones have been identifIed: the upper zone, characterized by an assemblage of quartz, carbonates, chlorite, albite, zeolite and sericite, and the lower zone containing diopside, tremolite, actinolite, gamet, clinozoisite, and epidote.The general features of the Laochang deposit are in accord with the descriptive model of VMS deposits (Lydon, 1984). However, it falls into neither the Zn-Cu group nor the Zn-Pb-Cu group chemically (Franklin et al., 1981). The depositional setting of the Laochang deposit is quite different from Cyprus or Besshi-type massive sulfide deposits. Laochang is hosted by alkaline lavas that were erupted in a submarine continental rift. Although some features of the Laochang deposit are similar to those of Kuroko-type deposits, there are remarkable differences in the alteration mineral assemblage, the proportion of ore-forming elements (lead enriched) and the amounts of oxides and sulfates. These suggest corresponding differences in ore fluid composition and the associated ore-forming environment. Thus, the authors suggest that the Laochang deposit may be a distinct type of VMS deposit."

Jan 1, 1993

By G. Heinrich

Size by size recoveries and pentlandite liberation data from image analysis were used to evaluate plant tests of pentlandite flotation and pentlandite/pyrrhotite middlings flotation from pyrrhotite in a circuit treating low grade magnetic intermediates at the Strathcona Mill. Raising the pH with lime gave improved selectivity for liberated pentlandite but there were major losses of middlings unless the circuit was pulled hard indicating the need for finer regrinding. However, size by size recoveries at the normal regrind showed that, while the pentlandite recovery improved in the finer ranges, the pyrrhotite recovery also increased leading to little selectivity in any size range. A much finer regrind gave greatly improved selectivity in all size classes suggesting that 'surface polishing' as well as liberation effects were being seen. Using liberation data from image analysis of the products, surface polishing accounted for over 99 % of the improvement in selectivity. Unreasonable recoveries of more highly liberated particles were observed for liberation analysis by volume fraction but showed the expected trend in recovery when the analysis was based on surface liberation. The surface liberation data showed that the improved pentlandite recoveries after finer regrinding were to more than 90 % caused by improved liberation with the remainder contributed by surface polishing effects. The practical implications of this work are that i) the comparison of particle grades with product grades allows to estimate the effect of regrinding on co-flotation/entrainment, ii) surface liberation models should be used for evaluating recoverabilities by flotation and iii) regrind circuits may be set up to ensure that all particles go through the mill or that only the coarse fraction is reground depending on the surface scrubbing found to be required.

Jan 1, 1993

By R. S. Adhikari

This paper presents an innovative computer vision method for condition assessments of bridges with multiple defects in bridge elements using digital images. This work utilizes 3D model of existing bridges and overlays digital images on 3D model to simulate on-site visual inspection. The analysis of element condition index (ECI) of bridges requires information about the severity and extent of defects in elements. In general, ECI is evaluated manually during routine bridge inspection considering the severity of dominant defects. The evaluation of ECI with multiple defects needs to be addressed with consideration of dominant defect as well as the interaction among defects. However, Image-based quantification techniques largely depend on geometry of objects (i.e. shapes). Shape vectors of a given object change as they are translated, rotated, and scaled with different magnitudes. This work considers shape preserving algorithms such as, affine and projective transformation for proper image alignment. Semi-automated approach for detection and quantification of concrete distress such as cracks and spalling are considered for the defects analysis. The proposed methodology ensures the consistency in reporting ECI and eliminates the shortcoming of traditional approaches.

Aug 1, 2013

By Joël P. T. Kapusta, Liam J. Watt

The last extended copper smelting and converting survey dates back to the 2003 International Copper Conference held in Santiago, Chile. The following year, the Minerals, Metals, and Materials Society of AIME (TMS) started a new series in its Journal of Metals (JOM) called JOM World Nonferrous Smelters Survey devoting its first Part to Copper. The copper smelting landscape has significantly changed in the past 15 years, both in geographical terms with the shift of copper smelting production from the Americas to China and in technological terms with the growing adoption rate of Top-Submerged Lancing (TSL) technologies and the development and implementation of Bottom-Blowing technologies. A copper smelting survey update, even if not as in-depth as the 2003 Copper Smelting Survey, is therefore in order. The authors will review the latest trends in copper smelting technologies and production worldwide in comparison to the landscape of the early 2000s. INTRODUCTION This 2019 copper smelting survey is different from previous surveys as our data does not originate exclusively from responses to a questionnaire sent to all the copper smelters. Our data comes from several sources. We are therefore very thankful to the International Copper Study Group (ICSG) and Wood Mackenzie for sharing some of their information and to ENFI, Outotec, and Glencore Technologies for helping us cross-check our numbers for the Chinese smelters, flash smelting, Ausmelt, and Isasmelt technologies. Our survey presents data reporting from a total of 96 operating copper smelters from around the globe, which is significantly higher than the 50 surveyed in 2003. Although secondary smelting numbers have steadily increased over time, this paper focuses on primary smelting operations with copper concentrate as feed material. The list in this survey is still far from complete, with missing information from several known smelting operations. The total primary copper production tonnage of the smelters we surveyed amounts to 18.3 million metric tonnes from 29 countries representing 92% and 94% of total world primary production for 2018 estimated by ICSG and Wood Mackenzie, respectively. This representation has increased from 2003 when the total was 9.71 million metric tonnes from 23 countries accounting for 73% of world production. The trends presented and analyzed within this paper have stronger significance because of the increase in production accounted for. The Chinese and Russian smelter information collected is more detailed than years past. Our complete dataset is summarized in Table 1 at the end of our paper.

Jan 1, 2019

By V. K. Srivastava1

Coal mine fires burn about 20?21 million tons of coal per year throughout the world, which not only results in loss of valuable coal reserves, but also cause serious environmental hazards over large areas. The famous Jharia Coalfield of Dhanbad, India is no exception; here a coal mine fire originally reported nearly a century ago is still continuing unabated in vast areas of the coalfield. In this paper, an attempt has been made to analyse high resolution multispectral thermal images of ASTER for mapping and delineating surface and subsurface coal mine fire areas of this coalfield. From the generated temperature gradient map, as well as from the surface temperature anomaly map, it has been possible to differentiate shallow and deep coal mine fire regions and other erroneous cultural features. It is observed that the coal fires are distributed mostly in the eastern part of the area, which has branched into two major coal fire zones: one along Lodna- Tisra-Bhulanbarari-Kujama-Jealgora Jharia and the other along the Kusunda-Kendudih area. The western fire zone is restricted in Dumra-Nadkhurkee-Jayramdih area. From ASTER thermal infrared data from 2006, the total affected area is estimated to be about 7 km2, of which the deep subsurface coal mine fire area is around 3 km2 and the shallow surface coal mine fire area is around 4 km2, as compared to 18 km2 coal mine fire area estimated in 1987 using Landsat TM thermal band data. In other words, the fireaffected region has decreased by about 50 % during the last 18 years. However, such decrease in coal fire area is seen in the central portion only, and has in fact increased in the south eastern parts of the Jharia coalfield. Study of Differential Interferometery images, generated from Earth Resources Satellite (ERS) synthetic aperture radar (SAR) tandem data has shown that the active coal mine fires are in general associated with low topography/subsidence areas.

Aug 1, 2013

By L. Beiza, L. Velásquez-Yévenes

Chalcopyrite is by far the most abundant copper sulphide on Earth, but it has proved to be problematic in its processing by leaching, mainly related to its refractory nature, slow kinetic rates of dissolution and the formation of an inhibiting product layer on its surface during leaching. This study is focussed on the electrochemistry of chalcopyrite dissolution in acidic chloride system, which has recently gained attention as a feasible alternative to conventional sulphate media for chalcopyrite leaching. It is well understood that chalcopyrite dissolution from mineral grains depends strongly on the solution redox potential at the mineral surface as well as the composition of the product layer that may form on its surface. The chloride ions in solution support the Cu(II)/Cu(I) couple as the primary oxidant, as they can form complexes with the cuprous ions formed, increasing the dissolution rate. Additionally, these ions increase the potential range where chalcopyrite can be oxidized. The chemical reaction that occurs on the surface of chalcopyrite in chloride solutions in the presence of cupric ions will be characterized and the coulometry of the reaction will be reported to understand what is happening on the surface of chalcopyrite. Electrochemical experiments have been carried out to investigate the behaviour of mixed potential by open circuit potential (OCP) measurement for 30 minutes using sulphuric acid at pH 1 under nitrogen at 25⁰ C. The effect of chloride was analysed at 0, 20, 50 and 100 g/L and cupric ions from 0 to 50 g/L. The potentials obtained were then used to carry out chronoamperometry tests for a period of 30 minutes in absence of cupric ions. The mixed potential did not show a significant difference with an increase in cupric concentrations in the absence of chloride. Increased mixed potentials and current densities were observed at higher chloride and cupric concentrations. Chronoamperometry tests at those potentials were used to construct a voltammogram trace which has the same trend as a normal cyclic voltammogram but with much lower current densities. INTRODUCTION As a result of the depletion of copper oxides, the leaching of copper sulphide minerals has become the focus of many studies. Chalcopyrite, (CuFeS2) which is the most abundant of copper minerals, has proved to be challenging to process via hydrometallurgy, mainly related to its refractory nature, slow kinetic rates of dissolution and the formation of an inhibiting product layer on its surface, during leaching.

Jan 1, 2019

By A. Sargeant

This paper evaluates the application of post consumer glass as a cementing agent in underground mine backfills. The underlying theory indicates that glass is pozzolanic and, when used in a finely divided form, behaves as an activator to generate binding products, thus contributing to the development of backfill strength. The objective of this study was to evaluate the strength performance of backfills when Normal Portland Cement is replaced with various percentages of post consumer glass. The study evaluated the performance of backfills prepared using tailings from three mines. Each backfill was prepared using unique recipes, and were evaluated at cure times of 7, 14, 28, 56, 112 and 224 days. Laboratory work involved visual, physical and chemical material characterization followed by strength evaluations. Results of strength assessment revealed that backfill prepared with glass is reactive and can contribute to the strength of backfill. The results also indicated that the reactivity of glass may be affected by the incorporation of slag within the recipe, the availability of lime and the level of hydration of the binders. The study concluded that, at 15 % glass replacement of NPC, backfill prepared with mine tailings, NPC and glass can achieve improved or equivalent strength performance compared to backfill prepared tailings and NPC alone.

May 1, 2007

By I. Silin, M. Stapelmann, H. Wotruba, K. M. Hahn, C. Gerold, J. Katzmarzyk

New deposits are often characterized as low-grade and complex ore bodies. To date, processing of fine grained ore deposits implies complex processing routes with high energy consumption. For that reason, the investigation of dry grinding, e.g. with vertical roller mills (VRM), is an approach to save energy reserves. It is already proven that dry grinding can influence subsequent processing steps. In terms of flotation, the surface characteristics of the minerals are crucial for a successful flotation process, e.g. the sufficient adhesion of mineral particles and air bubbles. Wet grinding results in different surface properties of the product entering the conditioning stage than dry grinding, which has direct influences on the subsequent flotation process. To investigate the consequences for flotation, processing of a copper sulfide ore containing chalcopyrite and bornite was investigated, including grinding and rougher flotation. The effects of wet tumbling mill and dry VRM grinding on the degree of liberation of valuable minerals are characterized using mineral liberation analysis by scanning electron microscopy. The obtained flotation results, as well as the recorded flotation parameters such as dissolved oxygen, oxidation reduction potential and conductivity are presented and discussed. INTRODUCTION Copper production is mainly connected to porphyry copper deposits as main source for copper sulfides such as chalcopyrite and bornite. State-of-the-art processing of these deposits is already established worldwide for decades, combining crushing, fine grinding and subsequent flotation with rougher, cleaner and scavenger stages (del Villar, Desbiens, & Maldonado, Bouchard, 2010). While the demand for copper is increasing, copper grades of the deposits are decreasing and the remaining ore bodies have more complex mineralogy and finer particle size distribution. This implies processing routes with high water and – due to the liberation of fine grained valuable minerals – high energy consumption by fine grinding. One of the main energy consumers in processing plants is the grinding section, which accounts for more than 50% of the energy consumption in processing plants and even 4% of the worldwide energy consumption (Jeswiet, & Szekeres, 2016). Therefore, dry fine grinding alternatives are applied to enhance the overall energy consumption of mineral processing plants: high pressure grinding rolls (HPGR) and vertical roller mills (VRM).

Jan 1, 2019

By P. Latostenmaa, T. Veneranta, J. Järvi, E. J. Peuraniemi

Boliden Harjavalta has operated a copper flash smelter since 1949 thus the smelter celebrates 70th anniversary of flash smelting in 2019. This paper shortly describes the historical perspective of the smelter and gives an update of the current operational issues and process modifications made during the recent years. The plant has carried out several major investments lately providing a firm view on the future. A new landfill area for the final slag was commissioned in 2018. A modernization of the concentrate storage area, a new acid plant and a debottlenecking project of the smelting line have been recently commissioned. At the same time, the tankhouse capacity will be expanded. This paper focuses on smelter modernizations. INTRODUCTION Boliden is a metal company operating mainly in northern Europe with core competencies in the fields of exploration, mining, smelting and metal recycling. Boliden Harjavalta, located in Finland, is part of the Smelters Business area of the Boliden Group and operates a copper and nickel smelter with related sulphuric acid plant in Harjavalta, and a copper refinery in Pori. As a short historical review, Harjavalta’s history may be dated back to the year 1910 when the Outokumpu ore body in eastern Finland was discovered. By the end of 1913, a copper mine was in operation and a copper plant based on Hybinette process was ready for commissioning. Due to difficulties in metal recoveries and throughput the Hybinette process was permanently shut down in 1929, and 100% of the mining production was sold as concentrate abroad. As the mine production increased steadily, a decision of a new smelter was made in early 30’s. In 1936 Outokumpu’s copper smelter based on electric smelting was commissioned in Imatra. The smelter was dismantled and transferred to Harjavalta during the final stages of the Second World War. The copper refinery started in Pori already in 1941 and the first copper anodes were cast in Harjavalta in 1945. First sulphuric acid plant started operation in 1947. Due to the post-war shortage of electrical energy, the plant metallurgists initiated a major development work to start exploiting the latent heat of concentrates. Thus, the flash smelting method was developed in Harjavalta and commissioned in 1949. Ten years later, flash smelting was also applied for nickel concentrates. Table 1 summarizes major historical and technical milestones of Harjavalta. The history of flash smelting is described in details in another paper of this conference (Jåfs et al., 2019).

Jan 1, 2019

By Adrian White

Agenda Overview of pastefill at Kidd Mine Pipeline wear and the need to monitor Steel Loop monitoring Steel Borehole monitoring Monitoring pipe linings

May 1, 2013

By M. Thérien, M. Rémillard

"Data from two industrial plants are treated by mass balance package BILMAT. The first application concerned a base metals/precious metals (PM) producer and the second, implementation of a hydrocyclone for the recovery of iron chips in the granite industry. Also LOTUS 123 software can easily be adapted for laboratory test mass balances using an IBM-PC computer. INTRODUCTIONThe present paper deals with two different BILMAT program applications. The first application concerns a copper-zinc-gol d-sil Yer producer based in North-western Quebec and the second, concerns the iriplementation of a hydrocyclone for the recovery of iron chips in Quebec granite company.Afterwards, we deal with some LOTUS 123 software applications for laboratory test mass balances using an IBM-PC.1. Base metal and P.M. producerNoranda Inc, Mattagami division, which operates mines in North Western Quebec, produces copper and zinc concentrates from a sulphide ore. Small amounts of gold (0,34 g/t) and silver (20 g/tl are present. At the time of the study, only 30% of the silver content was recovered in the copper concentrate. The main objective of this study is, to evaluate the metallurgical behaviour of silver in the flotation circuits, to increase its recovery in the copper concentrate and therefore to improve its final economic value. It is then worthwhile to identify the silver bearing minerals and to determine the critical flotation stages where they are lost. The methodology proposed is based on the coupling of a mineralogical study and a detailed mass balance ca1cu1ation in the flotation circuit performed using the BILMAT mass balance package (1, 2, 3).The results are discussed with respect to the distribution of silver in the circuit. The recoveries obtained at the various separation stages for the minerals present in the ore are also discussed."

Jan 1, 1987

By Stavros A. Argyropoulos, Radhakrishna Valiveti, Bernard Closset

"The use of microprocessors in metallurgy is currently increasing at a very fast rate. A large number of companies are offering systems ""off the shelf"" which are aimed at the data acquisition and process control market. There are two main drawbacks to these systems: first, they are usually quite expensive, and second, they are not completely compatible with the target metallurgical application. An alternative is to develop a microcomputer-based system "" in lab "".A dedicated microcomputer system has proved to be very useful in many metallurgical research applications(1,2)). However, in this system the analog input signals had to be transferred over long distances , and significant noise was introduced despite the use of shielded cables. In order to overcome this problem a network of low pass-filter s was designed and built. The usage of the abovementioned system brought the need to digitize the analog signals in-situ and transfer the digital signals, which are much less susceptible to noise over very long distances. This distinctly different design philosophy has become a reality with the evolution of microprocessor technology over the last few years. This design philosophy is utilized in this development."

Jan 1, 1984