Search Documents

By P. Czaja

The paper presents a patented and copyright protected concept of constructing a shaft lining that goes through rock masses having strong rheological properties and being susceptible to leaching. In the case of salt layers, especially at significant depths (over 900 m) the relative convergence of the heading contour may amount to 40 ?/year. That results in the fact that any other method of securing the shaft lining, e.g. by making it flexible, will not be sufficient to ensure the stability of the shaft reinforcement geometry. In the new shaft lining concept the excessive rock creep into the outbreak inside the shaft diameter will be removed by local and controlled leaching of the shaft cheeks by means of fresh water directed through a porous medium at the contact layer behind the watertight tubing lining. The paper presents the structure of such a lining and an outline of the construction technology. In order to implement such a lining, a typical tubing will be applied. Separate design and manufacturing will be required for the technological rings used to control the leaching process behind the lining.

Aug 1, 2013

By H. Sipilä, H. Vartiainen, H. Paarma

"The carbonatite massif of Sokli includes several low-grade Nb showings composed of ores and wastes as identified by routine analyses. More detailed lithologic proportions were determined in two orebodies in the Kaulusrova Nb-mineralized area by a careful geological study and by thorium radiation measurement on 10 cm-long drill core cuttings with a total length of 460 metres. The distribution of Nb in eight X-ray spectrometrically analyzed drill core sample intervals (totalling 35.8 m) was determined by analyzing the intervals semi-continuously by an X -MET analyzer. The geological studies suggest that Nb-mineralized bodies are feasible fo r the sorting of are and waste. This was confirmed by the semi-continuous determination of Nb on the X-MET analyzer.IntroductionThe Sokli carbonatite complex is located in eastern Finnish Lapland. The main ore of the carbonatite massif is a regolithic phosphorus ore in the weathered crust. Large-scale geophysical measurements and diamond drillings have also established several niobium showings within the magmatic carbonatites. Owing to the complicated geology of the massif, the niobium showings occur as irregular zones o r areas displaying complicated structure, texture, mineralogy and geochemistry (Vartiainen and Paarma , 1979; Vartiainen , 1980). The tonnages in areas such as this are large but the grades in-situ are low . The most intensely studied niobium showing is the Kaulusrova area.The exploitation of these showings depends on the feasibility of applying a sorting technique to upgrade the feed and to minimize the amount of material to be treated in the concentration plant. These possibilities o n the Kaulusrova area have been viewed by a detailed geological and X-MET an analyzing study."

Jan 1, 1985

By Sylvain Castonguay, Sylvain Pilon

"Operator competency is an important factor in the safe and successful operation of today’s complex processes. Competent process unit operators deliver superior performance and results. In greenfield projects, operator competency is particularly critical, as the lack of specific operations experience must be offset with proven practical knowledge and skills to avoid mistakes that can cost millions in terms of start-up delays, production losses and equipment damage. It is, therefore, important to know precisely what competencies are required for a project or site, and what any gaps in operator competency need to be addressed and improved. The success of plant commissioning, start-up and sustainable operations is directly tied to operator competency. The significant investments required for new projects, the exploitation of more challenging ore bodies, and the increasing complexity of plant operations have placed renewed emphasis on the need for competent operators. Furthermore, many large capital projects are being developed in remote regions, often with ties to the delivery of social benefits for the local population in terms of jobs, training and other development opportunities. While automation and processing technologies have helped do more with less, indicators now point to a bottleneck in human performance limiting operational results.Automation industry development in managing abnormal situations, including solutions for simulation and operator training, has produced applications to provide customized and flexible training methods. This paper will discuss tools to automate the operator competency process in order to guide trainers to effectively teach, measure, control, provide feedback, and monitor operator skills. Today’s competency management solutions can be effectively applied throughout the course of an operator’s professional life, as a guide to hiring new operators, for developing competencies to support operations, and also to develop and refine best practices and share lessons learned."

Jan 1, 2016

By S. Fox, Y. Fujita

Increasing demand for rare earth elements (REE) is expected to lead to new development and expansion in industries processing and or recycling REE. For some industrial operators, sending aqueous waste streams to a municipal wastewater treatment plant, or publicly owned treatment works (POTW), may be a cost effective disposal option. However, wastewaters that adversely affect the performance of biological wastewater treatment at the POTW will not be accepted. The objective of our research is to assess the effects of wastewaters that might be generated by new rare earth element (REE) beneficiation or recycling processes on biological wastewater treatment systems. We have been investigating the impact of yttrium and europium on the biological activity of activated sludge collected from an operating municipal wastewater treatment plant. We have also examined the effect of an organic complexant that is commonly used in REE extraction and separations; similar compounds may be a component of newly developed REE recycling processes. Our preliminary results indicate that in the presence of Eu, respiration rates for the activated sludge decrease relative to the no-Eu controls, at Eu concentrations ranging from <10 to 660 µM. Yttrium appears to inhibit respiration as well, although negative impacts have been observed only at the highest Y amendment level tested (660 µM). The organic complexant appears to have a negative impact on activated sludge activity as well, although results are variable. Ultimately the intent of this research is to help REE industries to develop environmentally friendly and economically sustainable beneficiation and recycling processes.

Jan 1, 2016

By R. del Villar, A. R. Laplante

"This article presents four grinding simulation programs, written in Applesoft BASIC. The firs t two calculate residence time distributions (RT Ds) for open and closed loops mills. The third program calculates the select ion functions from the RTD, breakage function and particle size distribution (PSD) o f the feed and discharge. Two linear regression programs are also included to calculate the breakage function. These results are used in the fourth program to simulate continuous or batch grinding kinetics.The modelling approach presented is the size discrete, time continuous matrix formulation presented by Reid (1965) from concepts originally proposed by Epstein (1948). It is at the present time the most widely accepted phenomenological model of grinding kinetics and is standard textbook material (Austin et 01., 1982; Kelly and Spottiswood, 1982, p. 152). The concepts of RTDs and tracer testing originated from chemical engineering theory and practice, and are well presented in Leven spiel (2n d Ed . 1972 , Ch. 9) .Applesoft* was chosen because it is compatible with many micro computers. It is also one of the simplest and least powerful BASIC versions. Thus it can easily be adapted to other more complex BASIC versions.Open Loop Residence Time Distributions (Program RTDOPEN)As mixing, channelling, stagnation and short-circuiting all affect slurry motion in tumbling mills, transport characteristics are very complex an d cannot be derived from fundamental principles. Fortunately , as grinding follows first order kinetics, transport characteristics for the purpose of grinding simulation ca n be represented by the RTD of the slurry phase . It is normally determined using liquid tracers, as it has been demonstrated and is commonly accepted that in industrial ball mill s, the RTD of the so lid phase is particle size independent and equal to that of the liquid phase."

Jan 1, 1985

By Norman Lecuyer, Jacque Nantel

"The Chadbourne Project, located within the limits of the town of Noranda, Quebec, will make use of backfill materials to fill the voids left by the mining of stopes and pillars. A series of tests were conducted on different mixtures of slag and pyrrhotite tailings materials to evaluate their properties. The tests are described and some pertinent results are given in the paper.IntroductionThe Chadbourne Project is located in the centre of the Town of Noranda, Quebec, with houses as close as 120 m from the blasting operations. The ore is mined using the vertical crater retreat method. The voids left by mining activities will be filled. A program of pillar recovery will follow.Considering the proximity of houses and the need to recover pillars, the backfill program must be carefully laid out. No subsidence can be tolerated on surface.With these objectives in mind, a test program was undertaken by Nantar Engineering Limited and Queen&apos;s University to evaluate the possible ba ckfilling alternatives available to Chadbourne. One of the possibilities retained was the use of a backfill composed of broken slag material from the Horne Smelter and pyrrhotite tailings deposited on the Horne&apos;s pond a number of years previously.The back fill used at the Horne Mine until the mine closed in 1975 was composed of a mixture of 97% granulated slag and 3% pyrrhotite tailings. The tests leading to its use underground at the Horne Mine were described by Patton in 1952. The structural properties of the Horne backfill were ""intuitively"" known; it was agreed by all at the Horne Mine that the backfill was behaving remarkably well. Some were labeling it ""the best backfilling material in the world"". Its strength was said to be that of a weak concrete. All of the preceding indicate that the Horne backfill had never had its structural and other properties determined in the laboratory."

Jan 1, 1983

By Roger C. Parsons

"The problems presented by ice formation and interference with processes, structures and mechanical operations in the mining industry can be expected to increase sharply as more of our mineraI needs are supplied from the far north. A process of rapid ice destruction is presented which lends itself to the effective removal or penetration of ice. Suggestions are offered for applying the system to problems related to mining activity in cold environments. The system can be readily adapted to large-scale operation, the reactant components being transported in crystalline form and volatilized on site.IntroductionThe number of operational mines in northern environments, relative to the number of mines in the temperate zone, will increase in the years ahead. This is not surprising, because:(a) in the past, those mines closest to centres of commerce had minimum transport charges and hence were more economic to develop;(b) great centres of commerce were far removed from northern environments;(c) the exhaustion of ores and lowering of grades in temperate zones now offset to some degree the extra transport costs applied to northern ores;(d) the abundance of excess energy in the north in the form of oil, gas and hydropower attracts mining as a means to justify its development; (e) assuming that the frequency of mineral occurrence north of the 52° N latitude is no different than south of it, there are many deposits waiting to be developed.As a result of current and projected activity in northern environments, we are faced today, and will be increasingly so in the future, with mining problems rarely encountered before-problems related to below-freezing temperatures. Engineering activity in permafrost regions will increase as new mining ventures are developed north of the 52° N latitude, roughly coinciding with the -1.1 ° C isotherm in Labrador, the upper temperature boundary for permafrost."

Jan 1, 1982

By B. M. Das, D. B. Cross

"In June 1983, the Computer Applications and Process Control Committee (CAPC) of the Canadian Institute of Mining and Metallurgy (CIM) circulated a questionnaire to coal mining, exploration and consulting companies in Canada to determine the industry&apos;s level of interest in holding a workshop-style meeting to introduce company personnel to ""state-of-the-art "" computer systems designed to carry out specific technical and management junctions. It was necessary to conduct the survey to determine the specific fields of application and the nature of training which are of most interest.Almost universally, the companies expressed interest in computer workshops and training for applications in the Canadian coal industry. The survey showed that all categories of personnel felt the need for some sort of training. Areas of specific interest identified were: exploration and geology, mine design, reserve calculations, coal mining technology, coal preparation, rock mechanics, ventilation, financial planning, and process simulation. The details of this survey together with an assessment of the significance of computer applications in the Canadian coal industry are presented in this paper."

Jan 1, 1986

By Jan Drzymala, Przemyslaw B. Kowalczuk

Froth flotation is widely used for upgrading of ores and other materials. Efficiency of flotation depends on many parameters, including type, chemical structure and dose of flotation reagents. Selection of a proper frother in flotation depends on the material used, necessary dose of frother and its selectivity. The selectivity of flotation can be characterized by proper separation factors and indices. In this paper separation selectivity and power of frothers were evaluated basing on separation data for a given material and frother, plotted as the recovery of the useful component in the concentrate versus the recovery of the remaining components in the tailing. Such a plot is called the Fuerstenau upgrading curve. The selectivity was defined as the location of the whole upgrading curve in relation to no and ideal separation lines, expressed on the scale from 50 (no separation) to 100% (ideal separation). In turn, the flotation power was defined as the dose of frother to reach a certain upgrading level at which recoveries of the useful and unwanted components are equal. The power and selectivity of frothers were determined for the Kupferschiefer stratiform copper ore floated in the presence of a fixed amount of xanthate and varying doses of frothers using a laboratory flotation machine. Basing on the separation results for different poly(propylene glycol) (CnH2n+1O(C3H6O)mH, CnPm) and poly(ethylene glycol) (CnH2n+1O(C2H4O)mH, CnEm) alkyl ethers, it was found that the concentrate yield and recovery of copper as the useful component in the concentrate were greatly influenced by the type and dose of frother. However, the same results plotted in the form of the Fuerstenau upgrading curve clearly indicated that the selectivity of frothers was similar, while their power was different. It proves that both selectivity and power of frothers are useful parameters for characterizing flotation systems.

Jan 1, 2016

By J. Kouam

Al-Si-Cu and Al-Si-Mg alloys are widely used in several applications. Although they can be produced near-net-shapes, products made of these alloys very often require some machining. The purpose of this study is to evaluate the machinability of A319 and A356 under TO and T6 conditions. The machinability was assessed using during dry drilling machining process and the machinability indexes used are the chip form, the chip breakability and the cutting forces. It is found that 319 and 356 exhibit different machinability behaviors, especially in the T6-condition in terms of forces requirements, chip breakability and chip segmentation. It is also found that both the microstructure of the workpiece materials and the machining conditions significantly affect the chip formation mechanism, and therefore, the machining parameters could be selected to promote a chip form that is easily manageable in production.

Jan 1, 2011

By A. Dahi Taleghani, A. Shojaei

Continuum damage mechanics (CDM) of rocks is studied together with their elastic and plastic behaviors to develop simulation tools for hydraulic fracturing jobs in naturally fractured formations. The model is constituted based upon pressure sensitive inelastic deformation of porous rocks and their damage mechanisms in the cases of drained and undrained conditions. The CDM model is formulated within Fracture mechanics framework. The performance of the developed elastoplastic and CDM models are compared with the available test data of a specific shale play. The hydraulic fractures growth in the reservoir scale is then simulated; in which the effect of fluid viscosity, natural fractures characteristics and differential stresses on induced fracture network is studied. The simulation results are compared with the available solutions in the literature. The developed CDM model outperforms the traditional fracture mechanics approaches by removing stress singularities at the fracture tips and simulation of progressive fractures without any essential need for remeshing.

Jan 1, 2015

By S. Gheibi, H. S. B. Duzgun, N. Dadashzadeh

It is widely recognized that there are various uncertainties in the analysis of rock slope stability owing to inadequate information for site characterization and inherent variability and measurement errors in geological and corresponding parameters. Therefore, reliability-based approaches that allow the systematic and quantitative treatment of these uncertainties have become a topic of increasing interest in rock slope engineering. There has been extensive reliability analysis of rock slope stability in the literature. However, all of these analyses are based on the First-Order Reliability Method (FORM). The probability of failure of a rock slope in the First-Order Reliability Method is provided by a linear approximation of the failure function. The FORM is most commonly used because it is efficient; its accuracy, however, deteriorates when the nonlinearity of limit-state function increases. A better approximation of the failure function can establish a more accurate value of the probability of failure. The Second-Order Reliability Method (SORM) overcomes this drawback with a cost of lower efficiency in terms of the number of function calls and computation expenses. Despite considerable studies of the application of the SORM in other engineering fields, a few attempts have been made in the slope stability studies. In this study, a recently published Second-Order Reliability Method with First-Order Efficiency (SORM-FOE) is implemented on a selected rock slope in Amasya, Turkey. The SORM-FOE overcomes the low efficiency of the SORM by decreasing the number of function calls. The probability of failure of both FORM and SORM-FOE are obtained and the results are compared. It is shown that, in high value of failure probability, SORM’s do not significantly affect the analysis and design. However, in very low failure probability, the discrepancy between FORM and SORM-FOE becomes pronounced. It is also shown that, where the second order methods are required, the SORM-FOE is more efficient than the conventional curvature fitting methods in terms of computational costs.

Jan 1, 2015

By Gary M. Bone

The autonomous control of vehicles interacting forcibly with their environment, such as dozers and tractors, is an unsolved and challenging problem. Forces and motions are inherently coupled between the tool and the means of vehicle propulsion. Furthermore, they are often operated within uncertain and unstructured environments, such as those encountered in underground mining. There is a growing industrial interest in the development of robotic vehicles to improve productivity, efficiency and safety in mining and construction. This paper focuses on the modeling and control of autonomous robotic dozing for a material removal operation. A dozing process model has been developed based on observations of both a fullscale dozer and a scaled-down version. The model characterizes the dynamic interactions between the blade position, material accumulation on the blade, material distribution in the environment, and the motions of the dozer. The dozing control objective is to remove the loose material as rapidly as possible by driving forwards at full power while automatically raising/lowering the blade in response to sensor measurements. Two different controllers were developed to meet this objective. The first controller is based on a set of heuristic rules, and the second is an optimal controller based on the dynamic model. An instrumented scaled-down robotic dozer and dozing environment, designed to emulate the full-scale operation, are used to implement the controllers and compare their performances over multiple dozing passes. Experimental results are presented showing that the model-based controller increased the material removal rate by 33% compared to the rule-based controller. Lastly, technologies for full-scale implementation are discussed, followed by proposed future work and conclusions.

Aug 1, 2013

By C. D. Smith

Numerous studies have shown the potential of air rate profiling to significantly improve the flotation performance of a bank of cells. To date many profiles have been implemented; balanced, increasing, decreasing and combinations of these. Previous work has typically shown using an increasing air rate profile, where the air rates are increased proportionally to each cell down the bank, yields a higher grade for a given recovery compared to other profiles. Air rate profiling can then be thought of as having two distinct components; determining the correct distribution of a given volume of air and, perhaps more importantly determining the correct total volume of air to add to the bank. To date no method for this second component has been established. In an alternative technique the air rate to each cell is adjusted in order to optimise the air recovery from that cell. Air recovery is the fraction of the inlet air which overflows the weir of a cell as unburst bubbles. The peak in air recovery (PAR) is a robust measurement that indicates optimal performance for the operating conditions in the cell, and sets the PAR air rate. By doing this for each cell in the bank, the optimal total air rate to the bank and the optimal distribution of that air can be simultaneously determined. In this study plant trials evaluated different air rate profiles, and profiling based on PAR. The total air rates to the bank for all profiles tested were approximately equal, allowing direct comparison. The results showed that the highest cumulative mineral recovery was achieved by operating at air rates which gave the PAR for each cell down the bank. Different distributions of the same total air rate to the bank gave the same cumulative upgrade ratio, but lower cumulative recoveries. In this study, the increase in cumulative mineral recovery, at the same upgrade ratio, was more than 33%. Peak in air recovery (PAR) based optimisation of air rates to banks of cells and to the individual cells has been shown to significantly improve flotation performance as it simultaneously determines the optimal air rate to the bank, and the optimal distribution of that air.

Jan 1, 2009

By Q. B. Li, B. Gonçalves da Silva, J. T. Germaine, H. H. Einstein, Z. Moradian

"Shale gas and oil production has grown rapidly in recent years, and consequently there are increasing demands to understand the mechanical and microseismic properties of shale. Acoustic emission (AE) monitoring provides useful information on the fracture mechanisms of shale rocks, and provides a basis for interpreting field seismic observations. While there have been attempts for microseismic monitoring of conventional hydrocarbon reservoirs, shale presents a large number of issues that require further investigation. For this purpose, experiments were conducted to understand the characteristics of the AE waveforms propagated through Opalinus shale rock in the time and frequency domains. Frequency range, arrival time, first arrival amplitude and other parameters such as counts, duration and energy of the waves generated from artificial and natural sources in the shale specimens were detected and compared with AE characteristics of granite, a brittle rock that has been extensively investigated. The experimental tests showed that there are some important factors that influence the analyses and interpretations of seismic surveys and microseismic monitoring of shale compared to granite. One of these factors is the anisotropic behavior of shale that causes the wave to propagate with different velocities in different directions. Also bedding planes and micro-discontinuities in the shale cause attenuation of the waves. Thus the AE waveforms that arrive at the sensor are a distorted and attenuated versions of the source waveform.INTRODUCTIONMonitoring microseismic activity from hydraulic fracturing of shale provides vital information for mapping injection paths and fluid migration in order to check the effectiveness of the hydraulic fracture stimulation. Analysis of microseismic source locations can be used to identify fracture networks induced or mobilized during the hydraulic fracturing operation (Rotherd and Shapiro, 2003). On the other hand, by monitoring and assessing detected signals from hydraulic fracturing one can evaluate the induced seismic impact of the stimulation operation.While there have been attempts to monitor microseismic events in conventional hydrocarbon reservoirs, shale presents a large number of issues that require further investigation. For this purpose, experiments were conducted on Opalinus shale to understand its acoustic emission (AE) characteristics in the time and frequency domains."

Jan 1, 2015

"The gravimetric dust sampler is one of the tools now available to the industrial hygienists for determining the worker &apos;s exposure to the numerous types of particulate matter that may be present in the workplace. The paper &apos; reviews the different sampling trains that can be used for the two major criteria for respirable dust and some of the sources of error in this dust assessment technique.IntroductionIt may be stated simply that the measurement of airborne dust in the working environment is done for one or two reasons: namely, for engineering control purposes and! or to evaluate the potential for toxicological insult arising from the inhalation of dust particles.This paper reviews the progress made in the development of dust-assessing instruments, particularly the gravimetric types designed to meet British and U.S. dust criteria , and discusses the limitations in their use for this purpose."

Jan 1, 1981

By Bertrand Wolfman, William E. Stanley

"This paper reviews the traditional mine accounting systems, including ""custodial accounting"" and unit costing, and then suggests that the use of flexible budgets represents a more suitable method of reporting costs in order to assist the mine manager in improving productivity. Examples of various applications are given to show that the result is a clear reporting structure.Custodial Accounting is Emphasized in Traditional SystemsTraditional mine accounting has been mainly concerned with the accuracy of financial reporting to ""head office"" for the use of the directors and the company&apos;s bankers and shareholders. This is often called custodial accounting and it represented the main purpose of accounting when first developed in Europe hundreds of years ago. This important development permitted the establishment of enterprises which were separated from their owners because they could rely on accurate financial reports of management&apos;s stewardship.As custodial accounting is fairly broad and historical in nature, it is often not very useful to the mine manager for ongoing monitoring of performance of mining, milling, maintenance, and other support and staff groups. In spite of the considerable investment in accounting staff and computer support, many accounting systems have not been upgraded so that they accurately reflect workplace performance on a weekly or monthly basis.Budgets are Often FixedMany mines today also still emphasize fixed budgets. Thus, the mine plan which is set in the fall of one year is converted to a monthly tonnage and detailed dollar budget for periods of up to sixteen months in the future. The only certainty in this plan is that actual events will differ; timing, mix of mining methods and production volumes will differ on a monthly basis.Unfortunately, the fixed budget has no capability to reflect these operational changes. It is frozen for the full year. The result is that actual results will inevitably be compared to an outdated target."

Jan 1, 1982

By Charles A. Schacht

"Relining, lining maintenance, and ladle repair can represent a significant cost in steelmaking. Therefore, the objective of all steelmaking shops is to minimize this cost and to maximize the lining life. However, the thermomechanical behaviour of the ladle lining is highly complicated and sometimes misunderstood. The ladle design also has a significant influence on lining life. Other factors which have a direct influence on lining life are the shop lining installation practices and manner in which the ladle is used. The objective of this paper is to provide an understanding of the impact of these factors as related to improving the integrity of the lining and increasing lining life.Fundamentals of Steelmaking Ladle Lining Expansion ForcesNumerous studies have been conducted by the author on steelmaking ladles with molten metal capacities ranging from 110 ton s to 350 tons. The steelmaking ladle typically has a sidewall plate with a slight taper and for analytical purposes can be classified as a cylindrical vessel.A typical ladle is described in Figure I. The ladle sidewall lining usually consists of a working lining and a safety lining. Although the type of refractory used in the working lining varies based on the type of steel produced and other metallurgical requirements, the refractories typically used are: 70% alumina brick; direct bond mag-chrome brick; resin bond dolomite brick; and direct bond dolomite brick. Fireclay brick, high alumina brick, or a similar strength brick is used as the safety lining.Normally, the ladle lining is exposed to a through-thickness temperature gradient and restrained by the ladle sidewall plate, is described in Figure 2. The hot face side of the refractory lining develops a compressive thermal force and the ladle sidewall plate develops an equilibrating tensile force. The radial joints open on the cold side of the working lining as the lining joints have little or no tensile strength. A radial compressive load (P) develops between the working lining and the vessel shell due to the thermal restraint imposed on the lining by the shell. The radial compressive load is transferred from the working lining through the safety lining onto the ladle sidewall. Therefore, the safety lining must have the strength to accommodate the radial compressive load (P)."

Jan 1, 1991

By Euler M. De Souza

"This paper presents a study developed to assess the potential use of salt tailings as backfill to control surface subsidence and as a mine bulkhead used to isolate areas of potential brine inflows. A series of index tests, centrifuge model tests and quasi-static creep consolidation tests were performed to evaluate the creep and consolidation properties of salt backfl1l and to evaluate the effect of brine inflow and brine infiltration on backfill behaviour. The centrifuge models were specifically designed to study the mechanical behaviour of salt backfill under the influence of brine inflow and long-term creep. Test results indicated that salt tailings could be applied underground as a bulkhead to seal off areas of potential inflow with the additional advantage of controlling room closure and local back instability. It is hoped that this study will assist mine planners to develop contingency plans to control brine inflow occurrences. IntroductionThe use of salt tailings as backfill is a technique that would assist in the control of potential brine inflows and surface subsidence, and would have a very positive impact on the long term adverse environmental effects associated with surface salt tailings disposal. A centrifuge testing program was designed to evaluate the behaviour of salt tailings as backfill; the effectiveness of salt backfill as a bulkhead used to isolate areas of potential brine inflow and the potential use of salt backfill to control surface subsidence. The testing program was also used to evaluate the creep-consolidation properties of salt backfill and to evaluate the effect of brine inflow and brine infiltration on backfill behaviour. This paper presents the results of the experimental centrifuge testing program and a comparison of results with models tested under I g using an electrohydraulic servo-controlled loading frame (MTS) and a creep consolidation cell. Applicability of the results to practical underground soft rock mining is also discussed.The centrifuge model tests indicated that salt tailings could be applied underground as bulkheads to seal off areas of potential inflow with the additional advantage of controlling room closure and local back instability. Because the applied stresses (1.2 MPa) and fill consolidation were relatively low, the centrifuge simulated bulkhead did not retain all of the inflow brine. At typical field stresses it is expected that the fill would be able to seal off panels with brine inflows. Further testing at higher stresses are suggested to determine the consolidation and stress levels at which the fill would completely retain any potential brine inflow head and positively act as mine bulkhead."

Jan 1, 1994

By John H. Fowler

"Barytes is one of the major components of drilling fluids used in oil and gas well-drilling. This mineral&apos;s close association with the petroleum industry bestows it with a commodity status not enjoyed by many other industrial minerals. Approximately 85% of world barytes production is used as a weighting agent in oil and gas well drilling while the remaining 15% is consumed mainly in the manufacture of barium chemicals, glass and as a pigment, filler or extender.Barytes mining began in Nova Scotia around 1865 and has continued until the present. Currently there are three barytes producers in the province one exporting pharmaceutical-grade barium sulphate and the other two supplying drilling mud-grade barytes to the offshore. Several barytes exploration and development programs are underway with excellent possibilities that Nova Scotia deposits will supply a significantly larger share of the drilling mud-grade barytes used in east coast drilling programs.Currently there is renewed interest in barytes activities in Nova Scotia because of its use as a weighting agent in drilling flu ids used in offshore oil and gas drilling programs.This paper reviews the use of barytes by the well drilling industry; outlines the history of barytes mining in the province, progressing to present-day exploration, development and production activities underway in Nova Scotia; and concludes with the market potential for Nova Scotia barytes."

Jan 1, 1986