Search Documents

By C. Barnett

"The mill at Noranda Mines Limited, Geco Division in Manitouwadge, Ontario went into production in 1957 treating 3,500 tons per day of copper, zinc, silver, lead ore. It was not until 1964, however, that the zinc concentrate drying plant was constructed. In 1970, milling capacity was increased from 4,000 to 5,000 tons per day. The zinc content of the ore is quite variable so that the tonnage of zinc concentrate dried varies from 200 to 650 tons per day.The drying plant was designed to dry 25 tons of zinc concentrate, dry basis, per hour from an initial moisture of 8.5% to a final moisture of 2%. Major components were selected so that capacity could be increased to 35 tons per hour with minor modifications.The rotary dryer is a Hardinge type ""XH-12"" with a diameter of 80"" and a length of 50 feet. The all welded construction shell is 1/2 inch thick mild steel plate with 3/4"" thick reinforcing bands under the tires arranged for operation at a slope of 1/2 inch to the foot. The 3/8"" x 12"" radial flights are welded to the shell. There are no flights in the last ten feet of the shell in order to reduce dusting. This unit is driven by a 50 HP motor through a Hamilton type CD250 double reduction helical gear speed reducer. The shell speed is 5.8 RPM.The standard Peabody horizontal air heater has a rated capacity of 10,000,000 B.T.U. 's/Hr. The combustion chamber is lined with high temperature refractory brick and is air cooled. The conical outlet section of the air heater is lined with insulating fire-brick. The burner is a type AT wide range mechanical atomizer fired by a type ""CR"" gas-electric ignitor.The Bunker ""C"" fuel is supplied by a Compower duplex pumping, heating and straining unit, including tank hotwell, Powertronic oil line heating system with a 550/24 volt transformer."

Jan 1, 1972

By K. Blower

"Since there was no representative from Wesfrob Mines Limited, the information on their infra-red concentrate drying operation, which had been prepared by Mr. K. Blower, was presented by Mr, Dorland. Mr. Blower, in submitting the information, emphasized that their objectives in this operation were (a) to guarantee less than 90%, of flow-moisture in their copper concentrates and thus satisfy marine shipping regulation• and (b) to minimize capital costs, The infra-red dryers have satisfied these objectives.To control final moisture in the copper concentrate, current practice is to preheat the filter cake with steam in the disc filter hood and then conveyor-0r7 the concentrate with infra-red calrod heaters. The application of steam aids the system as follows:1) Improves vacuum pump efficiency.2) Lowers viscosity of filtrate (increased temperature},3) Preheats the cake prior to radiant heating. (150°F)The hot cake discharging from the filter ranges from 10.6 to 10.9% moisture. After radiant heating the moisture level is reduced to 8.5% - 9.7% depending on production rate. Further moisture loss occurs during conveying and transferring to the stockpile for a final shipment moisture ranging from 8.1% to 9.5%. Production rate is frail J to 5 dry short tons per hour.1) #23 Conveyor 18"" flat belt covered from filter discharge to transfer point with 7 heaters end-to-end. Drive - Reeves Vari-Speed, 31:4 ratio, type 332-10-18, class ""D"", driving through a 24:1 ratio Dodge reducer. Speed of Conveyor - 3,9 feet per minute to 19.6 feet per minute. (Speed has been established and is not changed as a rule from the present level of a1:out 15.)2) #23 Conveyor 24"" wide, 20° troughed belt covered with 21 heaters, end-to-end from loading point, Speed - Constant at 54,2 feet per minute."

Jan 1, 1972

By A. C. Stevenson

"There are many critical application issues that affect all AC drives, but there are several that are absolutely mandatory for pulse width modulated (PWM) AC drives. If these rules are not followed, the drive system will have insulation, bearing EMI or noise problems. Pulse Width Output VoltageFigure 1 shows the output current of a typical pulse width modulated (PWM) drive. This is, of course, not a clean sine wave thus will have a lot of very significant harmonics. In fact, the harmonic spectrum is directly related to multiples of the carrier switching frequency plus side bands related to the basic output frequency. A typical spectrum for a PWM source bridge switching at 5 kHz is shown in Figure 2. Notice that the spectrum has multiples of the 5 kHz switching frequency and the number of side bands gets larger as the harmonic number increases.IGBT Switching TransientsWhenever we have PWM inverter switching, voltage transients are formed that propagate (usually at about half the speed of light) down the power cables to the motor just like in a radio frequency transmission line. If we do not terminate these transmission lines (motor cables) properly, the voltage pulses will be reflected when they reach the motor end and will be transiently increased up to twice their original amplitude.This transient voltage rise, shown in Figure 3, is important for three reasons:1. Insulation Voltage Stress — Higher voltage stress in the motor connecting cables and motor insulation will lead to a shorter insulation lifetime. If any of the voltage transient peaks exceed the insulation corona discharge level (partial discharge level), the insulation will gradually degrade with each voltage pulse. When it has been sufficiently degraded, it will then fail.Most new “inverter rated” motors have triple layer insulation which has a 1600 to 2000 volt partial discharge level. This will make them suitable to withstand the double voltage peak transient from a 600 volt inverter. It is wise to make sure of this fact, since a “standard” induction motor will only withstand about 1200 volts. Use of a standard motor in this application would shorten its life drastically. This can sometimes be as little as a matter of hours."

Jan 1, 2000

By Stephen Mullowney

Outline ? Setting the stage ? Deal activity ? Q1 2013 update ? Key deal sectors ? Deals by geography ? Outlook for 2013 Key Observations 2012 ? Major retreat in M&A activity ? Glencore-Xstrata deal dwarfs all other deals ? Gold & copper dominate deal activity

May 1, 2013

By M. Grenon

OBJECTIVE ?To link slope stability and financial assessment algorithms into a commercially available mine design software packages to provide integrated global pit optimization.

May 1, 2013

By Michael R. McPhie

Topics of Discussion 1. The Global Mining Initiative (GMI) and MMSD North America (Brief) 2. Task 2 of MMSD North America ? A Test for Sustainability 3. The Seven Questions and their Application 4. Key Recommendations and Next Steps GMI = Global Mining Initiative Significant international collaborative effort supported by more than 30 of the world?s largest mining/minerals firms which sought to involve all communities of interest. Three major streams of activities: 1. Mining, Minerals and Sustainable Development Project (MMSD) ? 4 regional Process (North America, Southern Africa, South America, Australia) 2. Creation of ICMM (formerly ICME) 3. Major conference in Toronto in May, 2002

May 1, 2002

By M. Behrouz

Thermal power plants convert thermal energy due to nuclear reactions or the combustion of coal, gas, heavy oil, or some other hydrocarbon to electrical energy. They consist of a variety of equipment, such as boilers, turbines, generators, cooling towers, and auxiliary equipment. Any factor that affects the equipment efficiency affects the overall efficiency. Analysis of the cooling tower and raw water using the Langlier Saturation and Ryznar Stability Indices showed that the cooling water at Sarchesmeh was slightly scaling with respect to silica. Cold lime softening was found to be a cost-effective method to produce cooling water with adequate properties to reduce the cooling water make up from 85 to 70 m3/h and blow down rate from 35 to 20 m3/h.

Jan 1, 2007

By R. R. Rogers

ABSTRACT The experiments described demonstrate that crude commercial lithium containing in the order of 0.5 per cent sodium can be refined, the resulting metal containing as low as 0.001 per cent sodium. During the process, the metal is vaporized and condensed at a gauge pressure of less than 0.04 micron. Considerable operating data and a detailed description of the experimental equipment are included. INTRODUCTION DUE TO THE unusual properties of lithium metal, its use is likely to increase considerably during the next few years (1, 2). This is of particular interest to Canadians because there are important deposits of lithium-containing minerals, especially spodumene, in Canada and it is hoped that lithium compounds and lithium metal will be produced from these deposits in the fairly near future. In order to assist in the development of this industry, the Mines Branch of the Department of Mines and Technical Surveys has initiated a programme of research in lithium metallurgy. In 1948, a paper (4) was published on methods of producing lithium metal and its alloys. Data on the corrosion resistance of some lithium alloys were included. In 1949, a paper (3) was published which showed that the addition of a small percentage of lithium to zinc anodes used for cathodic protection will improve their usefulness under certain circumstances.

Jan 1, 1951

By D. A. Sloan

"THE FIRST COMMENTATOR that I will call on is Mr. W. G. (Bill) Brissenden, Vice-President, Mines, Noranda Mines Ltd. Bill, would you care to comment.W. G. BRISSENDEN ...Mr. Chairman, Ladies and Gentlemen, I spent some time reading the four papers that were presented here, yesterday evening, and decided that the four to six minutes that I had been allotted for this afternoon were going to be pretty tough to meet. It's a very big subject and I just hope that I will be able to stay within my time limit. As has been so aptly demonstrated by the members of our panel here this afternoon young men in growing numbers continue to be attracted to careers in the mineral industry, especially to careers in mining engineering. Now from 80 the point of view that the profession may have regained its status this is indeed welcome news. However, perhaps all of the members seem to have the suspicion that the number of mining engineers that the industry can absorb is a much lower figure than previously forecast. It is said that technical school graduates are now occupying some of the jobs once considered the private preserve of the mining engineer and also that mining engineering undergraduates are having trouble locating summer employment. If these interpretations of mine are correct then we are now confronted not only with our old dilemma - whither the mining engineer - but also with an urgent need to solve it. We cannot allow our profession to become once again an undesirable one in the eyes of our youth because if we permit such a thing to happen a second time the profession may never recover."

Jan 1, 1972

By G. Paillard, I. E. Puddington, A. F. Sirianni, F. W. Meadus

Experiments with some selected Nova Scotia coals and a single sample of American anthracite, reconstituted in granular form with lower sulphur and ash contents by spherical agglomeration methods, are described. The effect of different bridging liquids, grinding times, gangue depressents and modes of agitation on the final product are discussed. The application of agglomeration techniques as a means of drying wet coal fines is also noted.

Jan 1, 1968

By L. Chunpongtong

The Athabasca oil sands mineable resource is located in northeastern Alberta, Canada. In oil sands mining, the ore zone is regulated to have a minimum mining thickness of 3 m and a cutoff grade of 7 wt.%. The current algorithm that is widely used to flag ore zones and waste zones tends to overestimate oil reserves and causes low-grade ore to be processed. This paper presents the development of a more complex algorithm that is more representative of the actual oil found during operations and that can prevent low-grade ore from being sent for processing.

Jan 1, 2014

By T S. Cochrane

A variety of practical tests have been tried in the mining industry to determine the support properties of mine roof bolts. Such tests include torsion wrench readings, hammer blow tests and the use of plates with built-in tension indicators. This paper gives some details of pull tests with a hydraulic jack, as carried out in coal mines of western Canada. M A~Y criteria exist for establishing the efficiency of roof bolting, and the one adopted de-pends on the nature of the problem and on the individual leanings of the investigators. Consequently, sufficient studies have not been made from a common viewpoint or under similar geological and techno-logical conditions to compare these methods of evaluation. However, regardless of whether certain tests provide sufficient factual data to form a basis for theoretical research on bolting or not, many of these tests can and do provide a positive means of judging the suitability of chosen roof bolting techniques and equipment under definite geological conditions.

Jan 1, 1963

By Nicholas Bonderoff, Amily Xu

The evaluation of battery electric vehicles (BEVs) in underground mines involves comprehensive business case analysis beyond just the capital and operating costs of the equipment itself. BEVs demonstrate benefits from an EHS perspective, reduced mine ventilation costs, lower energy operating costs, reduced overall GHG emissions (dependent on the source of electricity), elimination of DPM, lower equipment maintenance costs, and reduced cooling requirements in deep mines. When including batteries and supporting infrastructure, BEV capital costs are approx. 80% greater than that of diesel equipment. The project economics are highly dependent on the cost of electricity and diesel fuel, and these can vary widely depending on the location of the mining operation. Battery charging and swapping methodologies must be evaluated as there are a variety of approaches that can be employed which vary by manufacturer and type of equipment. Careful consideration of the cycle times, charging methodologies, and location of the battery charging infrastructure is necessary. Specific operating conditions must also be taken into consideration. For example, the time for blast gases to clear will be increased by reducing ventilation flow, and the potential impact on production needs to be evaluated. Similarly, the electrical distribution system needs to be evaluated for peak loading conditions when BEVs are charging. Criteria including maintainability, reliability, commercial availability, and performance need to be evaluated. BEVs have fewer components than diesel equipment and this correlates to lower overall maintenance costs, however, BEVs require maintenance personnel with specific skill sets in order to maintain the equipment. Battery lifecycle costs need to be considered as battery replacement incurs significant capital expense. Some manufacturers offer services to offset these capital costs through usage agreements. Recycling and disposal of batteries at the end of their lifecycles also need to be considered. With the increased selection of BEV equipment that will be available in the next 2-4 years, 100% BEV adoption is also possible. We recommend a holistic approach when evaluating BEVs for underground mines. This will ensure that everything is considered in order to evaluate the full impact of BEV implementation.

Jan 1, 2023

By M. Fan, H. E. Wyslouzil, J. Kohmeunch

Eriez HydroFloat(TM) separators and Canadian Process Technologies (CPT) flotation columns have been developed to overcome the limitations of traditional flotation cells in recovering coarse and fine particles, respectively. The flotation column can effectively separate 30-5 µm phosphate. Several industrial-scale HydroFloat separators have been installed in phosphate and potash beneficiation plants. Industrial-scale ultra-coarse (+850 µm) phosphate separation results suggest that a more-than 40% BonePhosphate- of-Lime (BPL) recovery increase and a 37% collector consumption reduction can be achieved. The paper describes the applications of Eriez HydroFloat separators to coarse particle separation and the CPT flotation column to fine/ultrafine particle flotation.

Jan 1, 2009

By Haipeng Li, Jacob Masliyah, Barun Gorain, Jian Huang, Qingxia Liu, Zhenghe Xu, AuTec Innovative Extractive Solutions Ltd.

"Froth flotation is widely used to selectively separate one or more minerals from an ore over a wide range of particle sizes with high efficiency. Bubble–particle attachment is one of the most critical steps in flotation. The objective of this project is to demonstrate the need for an innovative dual bubble generator to improve flotation efficiency. This dual bubble generator was designed to generate two different sizes (micron size and typical flotation size) bubbles. The micron size bubbles generated on the crevices of particle surfaces in venturi type of cavitation tubes enhanced the attachment of fine particles to the bubbles in conventional flotation systems. They also acted as a secondary collector, which has the potential to reduce operation cost and improve flotation recovery. The dual bubble generator was evaluated for a double refractory gold ore with 3g/t Au, 1.5 wt% TCM (total carbonaceous matter) and 0.7 wt% sulfides. The results were compared with those obtained using a commercial bubble generator. Compared with the commercial bubble generator, the dual bubble generator showed not only a higher gold recovery, but also an improved separation efficiency, demonstrating the potential of dual bubble generator in fine particle flotation.INTRODUCTIONFroth flotation has been widely used in mineral processing and waste water treatment. However, flotation has been proven inefficient for fine particle recovery although it becomes increasingly inevitable to process fine particles with the depletion of easy processing ores. The critical problem of fine particle flotation is the low attachment of fine particles to flotation size bubbles due to their low collision rate. Based on a commonly acceptable flotation model given by R =F*[Pc*Pa*(1-Pd)], the probability of bubble–particle collision (Pc), attachment (Pa) and particles detachment from air bubbles (Pd) collectively determines fine particle recovery (R) (Yoon and Luttrell, 1986). Since Pc = (3Dp/Db) where Dp and Db are diameters of particles and bubbles, respectively, bubble size and particle size impact the bubble-particle collision in opposite directions. It is evident that the probability of bubble–particle collision decreases with decreasing the size of particles, leading to a low recovery of fine particles. In this case, reducing the bubble size and/or increasing the apparent size of particles by fine particle aggregation are clear means to improve fine particle recovery."

Jan 1, 2016

By P. Au, P. Patnaik, H. Saari, D. Y. Seo, S. Bulmer

Ti-48Al-2Cr-2Nb-xW (where x = 0, 0.5, and 1 at. %) powders were consolidated by hot isostatic pressing (HIP). The consolidated samples were solution heat treated above the a-transus followed by stepped cooling to room temperature. Selected samples were subsequently aged at 950 °C for up to 72 hours. The post-heat treatment microstructure was examined by optical and electron microscopy. It was found that increasing holding time above the a-transus generated a more homogenous microstructure. Utilizing the stepped cooling sequence, especially with a transition temperature of 1270 °C, massively transformed gamma (Ym) was diminished. Aging caused coarsening of the fully lamellar microstructure in the 0%W and 0.5%W samples while almost no coarsening occurred in the 1 % W sample. Precipitates began to form during aging in samples containing W. The precipitates at the lamellar interfaces are fine and have a needle like shape, while precipitates at the lamellar grain boundaries are coarse and circular in shape. The size and number of the precipitates depend on aging time and the level ofW content.

Jan 1, 2006

By E. L. Warburton

Before entering into a discussion of wet washing, it will be advisable to consider the various phases and conditions sur- rounding the problem of cleaning coal from the Corbin mines. Corbin is located in the south-east part of British Columbia in the Crowsnest Pass district, about 35 miles north of the International boundary and about three miles west of the Flat-head Range of the Rocky Mountains. It is reached by a rail-way, about thirteen miles long, from McGillivray, B.C., a point on the Crowsnest branch of the Canadian Pacific rail-way, owned and operated by the Eastern British Columbia Railway Company, a subsidiary company of Corbin Coals, Limited. The coal is assumed to occur here, as principally elsewhere in the Rockies, in the Kootenai series of the Lower Cretaceous, but owing to the disturbed condition of the surrounding country and, therefore, the magnitude of the geological study involved, this has never been definitely worked out. The coal is of the usual Crowsnest high-grade steam-coal, containing from 9 to 12 per cent. of ash, but appears to have 4 to 5 per cent. less volatile combustible matter than other coals being mined in this district, a representative analysis being about as follows:

Jan 1, 1924

By M. Lundström

The Outotec HydroCopper® process is a novel technology, developed and registered by Outotec Technology Oy, for leaching copper from chalcopyrite using cupric chloride solution. The leaching process is operated at atmospheric pressure in a stirred tank reactor, at temperatures near the boiling point of water and pH values between 1.5 and 2.5. During the leaching of chalcopyrite in cupric chloride solution, a reaction product layer forms on the mineral surface. In the present work, the formation and the composition of the reaction product layer was studied in an environment similar to that of the HydroCopper® process. The effect of the process parameters on the reaction product layer was investigated. Electrochemical measurements, including A.C. impedance spectroscopy and microscopic observations were carried out and an equivalent circuit was used to determine the surface parameters, such as the reaction product layer capacitance and the charge transfer resistance. The results suggest that, at low pH, a passivating sulfur-rich layer forms, whereas at high pH, a more porous iron-rich layer was detected. The values measured can give useful information for optimising the leaching parameters of the HydroCopper® process. Cu2007

Jan 1, 2007

By C. J. Hodgson

"IntroductionThe Kitsault molybdenum mine is located 600 m above sea level on Lime Creek at the head of the inlet of Alice Arm, 140 km northeast of Prince Rupert, British Columbia (Fig. 1). The area of the mine is characterized by rugged topography and deeply incised creeks which drain into the Portland Canal - Observatory Inlet fjord system. Access is by air service or boat from Prince Rupert, or by secondary road from Terrace.HistoryThe deposit was first staked in 1911, at which time the main feature of interest was a polymetallic vein with values in silver located southeast of the molybdenum deposit (Woodcock and Carter, 1976). Turnbull (1916) was the first to describe the extensive zone of crisscross quartz stringers with Mo~ on the banks of Lime Creek which, although it clearly had the potential to contain a major deposit, was not then believed to be of commercial value.Following sporadic work through the 1920s and early 1930s, the ground lay idle unti11959 when Kennco Explorations (Western) Ltd. commenced a program of systematic diamond drilling on the stockwork-type mineralization adjacent to Lime Creek. In late 1964, Kennco announced the presence of an orebody of 36 million tonnes averaging 0.230Jo Mo~ which was to be put into production at a rate of 5450 tonnes per day under a new subsidiary, British Columbia Molybdenum Ltd., at a forecasted capital cost of $20 million (revised to $30 million).Between January 1968 and April 1972, 10.4 million kg of molybdenum were produced from 9.3 million tonnes of ore, at an average mill recovery of 90%, and with an average mill head grade of 0.206% Mo~. The ore was mined in an open pit with a waste to ore stip ratio of 1.5 to 1. The. operation was terminated in 1972 due to weak molybdenum prices and escalating costs.In May 1973, the deposit was purchased by Climax Molybdenum Corporation of British Columbia, Limited and in 1979 transferred to affiliate Amax of Canada Limited. In early 1979, following completion of detailed feasibility studies, Arnax commenced construction of the 10 900 tonne per day Kitsault mine and mill complex based on a mineable open pit reserve of 95 million tonnes at an average grade of 0.192% Mo~, sufficient for a mine life of 25 years. The original capital cost estimate was $143 million; it subsequently escalated to approximately $200 million."

Jan 1, 1995

By A. L. Mackie

Arsenic is a highly toxic element and a known human carcinogen. It is often a contaminant in mine water discharges, particularly from gold mining and roasting operations, and has been found at concentrations as high as 4 g/L. Increasingly stringent controls on the concentration of arsenic allowed to be discharged into the environment cannot always be met by current treatment processes and thus enhanced technologies are required to achieve low treated effluent concentrations at reasonable costs. A novel two-step physicochemical treatment process was developed and tested at the bench-scale using synthetic mine water solutions (SMWs) in order to reduce arsenic concentrations in treated effluent to exceed current discharge regulations. The process includes chemical coagulation with ferric sulphate and ballasted flocculation for enhanced solid-liquid separation. The SMW contained 59 ± 2 mg/L arsenic with a slightly alkaline pH. The effect of arsenic speciation on the process was tested by using either arsenite, As(III), or arsenate, As(V), in the SMW solutions. Tests were performed at cold temperature (3 ± 1 °C) to ensure the process? efficacy year-round in northern climates. Arsenic in As(V) SMW solutions was removed to a final total concentration of 0.0054 ± 0.002 mg/L, almost half the current recommended allowable drinking water concentration of 0.010 mg/L. As(III) was removed to a concentration below the Metal Mining Effluent Regulations? (MMER) current limit of 0.50 mg/L, to 0.32 ± 0.06 mg/L, with double the coagulant dose used in Stage 1 for As(V) removal. Oxidant addition at a concentration of 5 mg KMnO4/L in Stage 2 resulted in final total arsenic concentrations of 0.017 ± 0.002 mg/L and pH adjustment with lime in Stage 2 resulted in 0.0415 ± 0.0007 mg As/L in treated As(III) SMW. Both of these modifications to the process reduced arsenic concentrations to below proposed new MMER limits (i.e., 0.10 mg/L). This two-stage treatment process was shown to reduce arsenic concentrations to well below current treatment guidelines while reducing or eliminating chemical oxidant demand.

Aug 1, 2013