Search Documents

By L. Szecowka, M. Poskart, Siwka M. . J.

Oxides of nitrogen, created during combustion, are the most hazardous components of atmospheric pollution. However, it is possible to limit the negative influence of hazardous components on the natural environment. An experimental appartatus was built to determine the influence of the following "primary methods" on the reduction in concentration of NOx: air staging, reburning and flue gas recirculation. The influence of the simultaneous usage of the primary methods on reduction in NOx emissions was also examined. A significant increase in the efficiency of NOx reduction was achieved in two cases.

Jan 1, 2004

By Shugang Li

Coal and coal-bed methane are valuable energy resources. If they can be extracted simultaneously and safely, the triple purposes of mine safety production, new energy resource supply and environmental protection can be fulfilled. After mining, the mining induced fissure distribution feature and methane delivery behavior in overlying strata were closely related to the relieved methane degasification. Using physical simulation and numerical simulation, it was explained that the distribution feature of mining induced fissure was the Elliptic Paraboloid Zone (EPZ) in three-dimensional space. Based on the key stratum theory, the types, parameters, characteristics and dynamic evolution behavior of the mining induced fissure EPZ were analyzed. Applying environmental fluid mechanics and the mass transfer theory, the relieved methane floating-diffusion equation of the EPZ was established, and the corresponding transport process was analyzed. Using the field practice of relieved methane degasification in Tianchi Coal Mine, it explained that the mining induced fissure EPZ was the storage and delivery area of relieved methane. The degasification effect will thus be useful if the drainage system is laid in the EPZ. Such studies can provide the theoretical basis and technical support for the safe simultaneous extraction of coal and methane.

Aug 1, 2013

By L. Jiang

This report investigated the dynamic recrystallization (DRX) phenomenon in magnesium alloy AZ31 billets to understand the deformation mechanisms and microstructure evolution during extrusion and other metal forming processes, Compression tests of coarse-grained as-cast magnesium alloy billets containing lamellar Mg17Al12 eutectic phase and (Al, Mn) particles suggest that temperatures higher than 300°C, strains greater than 0,25 and strain rates above 0,l/s lead to the formation of fine DRX grains in the deformed samples. Microstructural observations also indicate particle-stimulated DRX nucleation (PSN) during hot deformation of the AZ31 alloy, facilitated by the presence of Mg17Al12 and (Al, Mn) particles, While the Mg17Al12 is dissolved into the matrix at about 350°C, (Al, Mn) particles may remain effective for PSN at temperatures up to at least 400°C, This study suggests that alloy design with a proper distribution of second-phase particles can provide the desired microstructure for improved properties and formability in wrought magnesium alloys.

Jan 1, 2004

By A. S. H. Kabir

Due to the high specific strength and excellent corrosion resistance, Ti-6A1-4V has been widely applied in aerospace industries. In this study, the welding performance of 3.2-mm and 5.1-mm thick Ti¬6A1-4V sheets was studied using a 4 kW continuous wave Nd: YAG laser. It is found that the use of filler wire, matching the parent metal composition, can bridge the joint gap and produce full penetrated welds up to a width of 0.6 mm without cracking. The laser welds were characterized in terms of the bead geometry, defects, microstructures, and hardness. With increasing joint gap, the percent porosity area increased, reaching just over 1% of the fusion zone area at a gap width of 0.6 mm for the 3.2 mm and 5.1 mm thick sheets. The maximum underfill depth in the Ti-6A1-4V laser welds was about 5% or 7% of the sheet thickness for the 3.2-mm and 5.2-mm thick materials, respectively, meeting the AWS D17-1 specification. The microindentation hardness was maximum in the fusion zone and sharply decreased through the heat affected zone until reaching the base metal value.

Jan 1, 2011

By J. Font

The RAF or copper fire refining process at the Caletones smelter of CodelcoChile consists of several pyrorefining stages that successively lowers the levels of S, Fe, Pb, As, Sb, Te, Se and to some extent 0 in the copper melt, allowing the production of high quality fire-refined copper of 99.93 % purity (RAF copper). This chemical feature of the RAF copper is only achieved by quite long processing times, and a considerable consumption of fluxes and fuels in the RAF vessels. The main goal of this study was to improve the RAF process performance by thermodynamic considerations and industrial scale tests, i.e., an in situ approach for the process as featured by intensive sampling, characterization and subsequent modifications. Thus, both theoretical and industrial data were derived, and based on kinetic and thermodynamic evaluations, a higher operational standard was achieved for the RAF process. These new operational practices allowed enhancing the overall economic of the RAF process, by reducing the time and operational costs, and consequently increasing the availability of the vessels.

Jan 1, 2007

By S. A. R. Keneti

Predicting the geomechanical response of the shale gas material during hydraulic fracturing operation in the field needs better understanding of their geomechanical behaviour under laboratory testing. Anisotropy is considered as a critical factor during investigation and analysis of deviated boreholes, borehole stability, stress-strain and strength behaviour, generation and propagation of fracture and fluid flow. In this study, compressive elastic modulus (Ec) of the Montney shale has been investigated in two perpendicular directions: unconfined compressive strengths test was conducted on the Montney sample to measure its Ec in the vertical direction. This value then was compared to the Ec value in the horizontal plane (i.e. foliation plane) which was previously measured throughout a Brazilian test by Keneti and Wong (2011). From the results, the representative values of Ec in the vertical and in the horizontal directions were found as 25 GPa and 40 GPa, respectively. Computer tomography technique was also employed for the experimental data interpretation.

Jun 1, 2012

By Gerald A. Crawford

"1880s - Unmasking the Sudbury Basin Falconbridge Ltd. turned 60 in 1988 but its roots go back more than a century to the discovery and development of the mineral resources of the Sudbury Basin. Nickel was first identified in the area in 1856 but sustained exploration awaited the early 1880s and the advance of the CPR westward from Sudbury. Rock was laid bare in the right-of-way and by forest fires and logging. Reddish oxidized outcropping or ""gossan"" were exposed, heralding the presence of nickel as the shape of this astounding geological formation gradually began to emerge. Many great mines of the area were opened up in this period on the south rim of the Basin west of Sudbury. To the east the ore dips below overburden, however, and Falconbridge remained a mere dot on the map until the turn of the century when Thomas Edison detected a magnetic occurrence by dip needle."

Jan 1, 1999

By Dennis Z. F. Mraz

"Because rock salt and pot ash formations contain particles capable of elastic deformation, the material has usually been compared with various rheological models containing elastic elements. Extensive laboratory testing of salt and potash samples resulted in various theoretical conclusions based on conditions quite different from those in a deep mine. It is felt that sufficient data have now been collected from underground measurements and observations to demonstrate the inelastic behaviour of salt masses in a deep mine. The conditions in deep salt strata can be defined as near hydrostatic, because the acting pressures are very high compared to the negligible elastic limit of the salt. The pressure field and creep around the single opening is a function of its shape, size and age. The same factors, together with extraction, determine the behaviour of the mining a rea. The application of the correct analytical method in mine design can significantly improve the excavation techniques and predetermine the long-term behaviour of openings."

Jan 1, 1973

By G. F. Trainor

The complex ore body at CNRL?s Horizon mine presents some unique challenges in managing ore and waste delivery. With 25m x 25m ore blocks shovels often take bucket loads from multiple blocks to fill one truck load. With CNRL monitoring 22 different qualities per material a precise calculation of the blended quality of ore on the back of each individual truck is essential to meet the daily blend requirements at the plant. Additionally, one of these qualities must be closely monitored and controlled at a singular level as delivery of certain grade and quantities can cause serious disruptions at the plant. The waste material also requires special handling and delivery for its use in dyke construction for tailings impoundment. Shale materials used in the construction contain high levels of saline that must be contained to prevent seepage into ground water. This paper will discuss how the use of Wenco?s survey-grade GNSS system on shovels, its dispatching algorithm, and fleet management applications give CNRL the ability and confidence to control and report on these three issues.

May 1, 2013

By Willie van Niekerk

As mining projects get larger and more complex there is a need to examine the use of project management techniques developed for large construction projects in order to ensure completion of the project on time and budget. In recent years the construction/civil industry has sought new methods to ensure that multimillion dollar projects involving multiple contractors, working in an increasingly legislated work environment, are delivered to the clients satisfaction. The paper describes these methods, which range from program management to systems and tools to gather all project information such as schedule and cost, and relates how these can be applied to large international mining projects. The paper also describes the benefits that an independent project manager can bring to a client or owner?s team by setting up the relevant organization and controls together with the appropriate contract and procurement strategy.

May 1, 2009

By V. Aprahamian, G. B. Harris, C. W. White, M. Tangen

"In 2005, the Royal Canadian Mint (RCM) commissioned a new silver electrorefining circuit. This circuit was intended to operate with a minimal electrolyte bleed for the control of copper. However, by the time of start-up, the levels of copper-rich silver doré to electrorefining had increased, and despite partial pyro-conversion in a small Top Blown Rotary Converter (TBRC), copper concentration in the silver anode still averaged 7.5%. This necessitated frequent replenishment of the electrolyte with fresh silver nitrate since copper displaced dissolved silver during electrolysis, and therefore requiring a robust copper bleed treatment step in order to maintain cathode silver flake purity at 99.99%. The originally-installed bleed treatment system could not meet the RCM’s needs. A thorough review of known technologies, however, did not indicate one capable of handling the copper load, and resulted, therefore, in the development of a novel copper hydrolysis approach for removal of copper as an insoluble basic nitrate salt, and recovery of the associated nitric acid for re-use in the circuit. Laboratory-scale trials showed reproducible results, and existing equipment was subsequently modified.INTRODUCTIONIn 2005, the introduction of a new silver electrorefining circuit at the Royal Canadian Mint (RCM) initiated changes in the way customer silver, collected from the gold doré circuit, was processed. These circuit changes were discussed in a recent paper (Aprahamian, 2015). A wastewater treatment plant had not been budgeted at the time, and this represented a significant constraint when considering the introduction of a wet processing circuit. After a review of various options, a turnkey silver electrorefining circuit was purchased from a European firm. Initially, enough cells were ordered to produce 2 million oz of fine silver (999), with the option to increase to 5 million oz. The selected equipment was based on a Moebius cell design combined with a silver grain pressure dissolver to produce make-up silver nitrate solution. Additionally, an evaporator/hydrolysis unit included in the package appealed to the Mint Refinery, on the basis that it offered a simple way to bleed dissolved copper in electrolyte without generating effluent."

Jan 1, 2016

By Erik Q. Dahl

The strength of green and sintered pellets during reduction under various conditions in a laboratory kiln has been investigated. Equipment and test methods are described, together with the results obtained. The strength of sintered pellets drops sharply when the reduction starts, and goes through a minimum at the 70 per cent oxidation level. At more advanced reduction, the strength increases with increasing metallization. Successful use of green pellets as kiln feed requires that more attention be paid to the pellet preparation than is necessary when producing pellets for separate sintering. In particular, the ores have to be ground to a greater fineness. The initial strength of green pellets is low. Below the 70 per cent oxidation level, however, the strength of these pellets is about the same as the strength of sintered ones. Additions of such materials as silica, limestone and anthracite coal; within reasonable limits, affect the strength only slightly.

Jan 1, 1966

By W. A. Jones

"The Ross mine, a subsidiary operation of Hollinger Consolidated Gold Mines, Limited, is near the north end of lot 1, con. II, Hislop tp., Ontario. The property comprises the north half of lot 1, con. II, and the south onethird of lot 1, con. III. It is readily reached by a good motor road from the village of Ramore, 7 1/2 miles to the southeast on the Ontario Northland railway. The mine is being developed to a depth of 1,500 feet, and the current daily production rate is approximately 300 tons. From the inception of operations in March 1935 until December 31, 1945, 692,000 tons of ore, with a total value of $5,762,685, was milled . The silver to gold ratio of 1.48 to 1 is unusually high for Ontario gold mines.TYPE OF 0REBODIES AND MINERALIZATIONThe orebodies consist of lens-shaped and pipe-like stringer lodes and tabular vein zones composed of parallel quartz stringers. The host rocks are steeply inclined eruptive breccias and tuffs, striking N.70°W., intruded by very small stocks of red syenite. The orebodies appear to be spatially related to an intricate system of fault planes. Hydrothermal alteration is widespread and is not zonally related to individual quartz stringers. The wall-rocks contain abundant fine-grained pyrite, but gold is confined to the quartz stringers.RELATIONSHIP TO REGIONAL STRUCTURELack of outcrops has prevented the detailed mapping of the Keewatin complex in the vicinity of the Ross mine with the degree of success that has been achieved in the Porcupine area.A northwesterly trending belt of slates and greywackes, bounded by faults, forms the central part of a broad anticlinal arch about 3 1/2 miles north of the Ross shaft. Lava flows forming the south flank of the structure face south toward the mine. If the sediments are to be tentatively correlated with the large areas of Keewatin slates and greywackes of the Porcupine area, it must be assumed that they are younger than the lava flows and that they have been down-faulted."

Jan 1, 1954

By J. B. Yianatos, F. A. Contreras

Mineral carrying rates across the pulp-froth interface in the range of 1.4-3.2 tph/m2 and bubble surface coverages between 7 and 22 %, have been determined in large rougher flotation cells operated under normal conditions. To evaluate these variables, measurements of bubble size distribution, bubble load and size distribution of particles collected by true flotation, were performed at different concentrators. A model for estimating the bubble surface coverage at the pulp-froth interface level as a function of bubble load, Sauter mean bubble diameter and particle size distribution of the mineral collected by true flotation, was developed. Bubble loadings in the range 24-70 kg/m3, bubble sizes between 1.5 and 3.2 mm and superficial gas rates between 1.2 and 2.0 emfs, were measured in copper rougher flotation cells under normal operating conditions. Estimated bubble surface area fluxes were in the range 31 to 62 cm2/s/cm2- Results of carrying rates and bubble surface coverage, at the pulp-froth interface, were significantly lower than the maximum carrying rate for the collection zone, indicating that in this case is difficult to achieve maximum carrying rate at the pulp-froth interface level. The main constraints regarding carrying capacity limitations are then related to the froth transport characteristics (i.e. cell design, froth residence time, froth stability, froth recovery). Advances in Mineral Processing Science and Technology Proceedings of the 48th Annual Conference of Metallurgists ofCIM Sudbury, Ontario, Canada Edited by

Jan 1, 2009

By M. Savich

A graphical method has been developed for the evaluation of the U.S. Occupational Safety and Health Act Noise Exposure Index and the Equivalent Continuous Sound Level. The method makes use of a noise survey form and a mechanical integrator with two sliders, and is less tedious and susceptible to error than alternative methods. The graphical method is adaptable to various codes for noise exposure and may be used with any instrument that measures noise level. One example of its application to a practical situation in a Canadian mine is given to demonstrate the procedure .

Jan 1, 1978

By A. Karzhau, B. Aldamzharov, Y. Tussupbekov

"This case study produced for the metal mine operating in Kazakhstan, which has ventilation controlled manually and working continuously at maximum speed to keep air flowing through each part of the mine 24 hours a day. The mine auxiliary ventilation has been designed with the maximum length of ducting systems with extra air volumes to compensate for potential leakage. The mine provided auxiliary ventilation to all production stopes even to those, which for various operating reasons become temporarily inactive. However, mine safety has to consider risks associated with the deficit of fresh air for mine gases dilution and removal. The mine needs additional investments for re-designing ventilation network and therefore needs to estimate financial risks associated with it. The aim of this study is to conduct risk analysis for ventilation network optimisation processes at the operational metal mine in Kazakhstan. Mine ventilation surveys were undertaken for validation of the computerised ventilation model. The mine ventilation network modelling has been undertaken to be compliant with Kazakhstan mining regulations. Results of the mine ventilation optimisation processes were analysed in terms of financial risks for investments into reconstruction of the ventilation shafts, extension of the ventilation network, variable speed fans and automated regulators. Savings were resulted from improving ventilation system efficiency by reduce airflow in areas without mining activity and redistributing existing ventilation capacity. Based on savings derived from the optimised ventilation network an additional NPV has been received. Stochastic modelling use Monte Carlo simulation producing representation of possible outcomes for the additional NPV considering electricity pricing as a major variability. As result probability distribution for the optimised ventilation network demonstrates the additional NPV in a range of 1.6 - 2.2 million US$ in the corresponding defined value of 90%. Moreover, there is only 5% chance that the additional NPV to be less than 1.5 million US$. Conducted risk analysis for ventilation network optimisation processes gives considerations on volume of investments into the mine ventilation system.INTRODUCTIONCosts for mine ventilation are typically increasing when mines expand to deep levels. Some underground mines in Kazakhstan still use continuously operating fans at its maximum capacity. This is not helping to save energy and costs that are in many cases very significant. This case study produced for the metal mine operating in Kazakhstan, which has ventilation controlled manually and working continuously at maximum speed to keep air flowing through each part of a mine 24 hours a day. The mine auxiliary ventilation has been designed with maximum length of ducting systems and extra air volumes to compensate for potential leakage. The mine provided auxiliary ventilation to all production stopes even to those, which for various operating reasons become temporarily inactive. However, mine safety has to consider risks associated with the deficit of fresh air for mine gases dilution and removal from the mine workings (Sabanov, 2019). The mine needs additional investments for re-designing ventilation networks and therefore need to estimate financial risks associated with it. The aim of this study is to conduct risk analysis for ventilation networks optimisation processes at the operational mine in Kazakhstan. Mine ventilation surveys for validation of the computerised ventilation model have been undertaken"

Jan 1, 2019

By A. C. Munro

The concrete work on the new Britannia mill was started in April, 1922. The erection of steel commenced on July 10th, following. The installation of wood work and machinery , began on November 4th of the same year and was pushed to completion in January, 1923. The new mill building is an all steel structure enclosed with galvanized corrugated steel. All main floors and foundations are of reinforced concrete, which makes the building practically fireproof throughout. The mill building rises on a steep hillside to a vertical elevation of 210 feet and has seven distinct floors, for the various opera-tions. Only one elevator, with 30-foot centres, is used in the entire mill. The building is exceptionally roomy and well lighted, both by day and night. The capacity of the mill, as originally designed, was to be 2000 tons daily, but this tonnage can be readily increased to over 3000 tons daily by making slight changes in the fine grinding equipment; in fact, an average of 2700 tons per 24 hours was maintained throughout the month of September.

Jan 1, 1923

By G. Hu, P. Chang

"As hydraulic fracturing is forbidden in some countries due to its accompanying environmental pollutions, microwave fracturing was proposed as a substitute technology to enhance coal seam permeability. Its mechanism includes: on the one hand, thermal stress caused by non-uniform microwave heating leads to fracture development in coal body, which increases coal seam permeability for gas; on the other hand, moisture within the coal body that hinders gas desorption and diffusion is removed during this process. To study the effect of moisture content on fracture development under microwave irradiation, high resolution photographs were taken before and after microwave treatment. These photographs were then binarized and skeletonized. Based on the processed photographs, the total area were calculated using ImageJ. The results showed that coal samples with 0% and 25% water saturation have more variation in fracture development as compared to that of samples with 50%, 75% and 100% water saturation. This study can be very useful in gas drainage and gas control in coal mines. INTRODUCTION Coalbed methane (CBM) is a clean energy source as well as a natural hazard to underground mining (Kurnia, Sasmito, & Mujumdar, 2014; Ranathunga, Perera, & Ranjith, 2014). One of the main goals of mine ventilation is diluting methane and removing underground contaminants (Xu, Huang, Nie, Chalmers, & Yang, 2017). Coalbed methane (CBM) has to be extracted prior and during underground mining to avoid methane outburst and explosion accidents. However, with the increase of mining depth, the coal permeability decreases significantly, which makes it hard to extract the methane (Huang, Xu, Hu, Kizil, & Chen, 2018). To enhance the coal seam permeability, many CBM recovery methods have been applied on-site, such as hydraulic fracturing and enhanced coalbed methane (ECBM). However, hydraulic fracturing is restricted due to environmental concerns and ECBM is only suitable for the coal seam with relative large permeability (Bustin, Bustin, Chikatamarla, Downey, & Mansoori, 2016; Huang, Xu, Chen, & Chen, 2018; Huang, Xu, Hu, et al., 2018)."

Jan 1, 2019

By O. A. Ojo, R. G. Ding, M. C. Chaturvedi

In this study, the fusion zone microstructure of tungsten inert gas weld of a directionally solidified NhAl-base alloy was examined by the standard metallographic techniques involving the use of optical, analytical scanning and transmission electron microscopes equipped with energy dispersive spectrometer. Fusion zone cracking was observed to be closely associated with interdendritic secondary solidification microconstituents identified as consisting of y, y' and NiMo (Y) phases. Depression of solidification temperature to the terminal ternary eutectic reaction temperature of the system during cooling is suggested as an important factor contributing to the fusion zone cracking.

Jan 1, 2006

By Wael Abdellah

Mine haulage drifts are the primary access to the mining blocks of an orebody in a multilevel mining system of a tabular ore deposit. The stability and functionality of haulage drifts are thus crucial to the success of a mining operation. Drift instability could lead to serious consequences such as injuries, production delays and higher operational cost. In this paper, the performance of the haulage drift stability is evaluated on the basis of the primary rock support system comprising 1.8 m resin grouted rebars in the drift walls and 2.1 m long bolt in the back. Two failure criteria namely the extent of Mohr-Coulomb yield zones around the drift, and linear elastic brittle shear failure are adopted and compared, with respect to lower level and same-level mining and filling sequence in the vicinity of the haulage drift. The case study is one of the #1 Shear East zone of the Garson Mine in Sudbury, Ontario. Random Monte Carlo (RMC) technique, which has been previously established to assess the haulage drift stability, is employed in this investigation. The RMC technique is used in conjunction with finite difference modelling software FLAC for random assignment of model input parameters in the FLAC grid. Deterministic model results reveal the drift behaviour in terms of deformation (convergence) and mining-induced stress distribution. Comparison between the two different criteria is carried out to determine which method is most suitable in evaluating unsatisfactory drift performance. The results are presented in terms of probability of instability and categorized with respect to failure condition and mining step. It is shown that the brittle shear failure condition based on linear elastic response calls for enhanced support system at a later mining step than what Mohr- Coulomb yielding condition does. The paper presents a detailed discussion of the stochastic analysis results.

Jun 1, 2012