Search Documents

By T. Patching

"Introduction The occurrence of coal was first reported in the Drumheller area in 1793 but it was not until 1912 that production of coal was recorded. In that year 13,000 tonnes were mined in the Drumheller area. Three years later the Drumheller mines ranked next in the Province to those in the Crowsnest and Lethbridge districts, with an output of 225,000 tonnes. By 1917 production had increased to 600,000 tonnes, moving Drumheller to second place in output in the province, second only to the Crowsnest district. It held this rank until 1960. Production, almost all from underground mining, rose to over a million tonnes a year by 1920 and remained between one and two million tonnes per year until 1954. Competition from newly discovered oil and natural gas, beginning around 1950 caused a steady loss of domestic coal markets, especially from underground mines. By 1960 Drumheller's production had fallen below a half a million tonnes per year and the field ranked third in output in the province, being surpassed by new stripping operations in the Castor field. By 1965 only a couple of producing mines remained in the Drumheller valley, and output was only about a quarter of a million tonnes per year(1). Throughout the life of the field production was seasonal, depending mainly on the domestic heating market. In 1979 the last mine ceased production. For the last several years of its operation it had remained open in the summers to provide tours for visitors(2). The Drumheller mining operations were located along or near the Red Deer River valley which is 300 to 400 feet deep, and extended from a few miles above the city of Drumheller to East Coulee, about 13 miles down the river in a south-easterly direction. Intervening mining communities existed for some years at Wayne and Rosedale. During the peak years of production some 2000 to 2500 miners and their families lived in these communities and the surrounding areas."

Jan 1, 1985

By B. A. McKee, T. Adamcewicz

For a capital expenditure of only $46,000, Caland Ore Company has successfully converted its three dry grinding center peripheral discharge rod mills to dry grinding ball mills. The conversion has resulted in a significant capacity increase, operating cost reductions and in-plant environmental improvements. This paper describes why and how• the conversion was made.

Jan 1, 1972

By James A. H. Church

This paper is in the nature of a protest against the dangerous propaganda afoot for the prevention of new mining undertakings and which is based on the imaginary 'blue ruin' conditions supposed to exist in the industry. An article by Mr. G. R. Pratt, A.M.E.I.C. in the first issue of the Western Canada News, February 2nd, 1925, and entitled "Review of Coal Mining in Alberta", is an excellent example of this type of propaganda. The article is a tissue of misstatements, faulty deductions and erroneous conclusions. For instance it contains the statement that some coal measures in Alberta are mined at great depth - whereas we all know that there is no coal mined at great depth anywhere in the province; another error is the classification of all mines under one head irrespective of whether they are mining prospects, 'country banks', or pukka mines equipped with railway facilities; and I believe that suppressio veri is tantamount to suggestio falsi. The bulk of his article hinges on a Table 1, which shows the details of coal produced in Alberta during 1923. Studying this table Mr. Pratt, in the manner of a conjurer producing rabbits from a hat, offers the following for the confusion of the public:- (1) "Waste effort, want of capital, waste of coal resources which result from unrestricted development"; the fact being that the waste is due to the failure of the Department of the Interior to exercise the powers which are inherent in the form of lease.

Jan 1, 1925

By Normand Champigny

The Forces of Change ? The current business environment ? What can we expect for the future on management of physical assets ? The impact of maintenance on production costs ? What is RCM is doing is improving business performance ? The beginnings of RCM The RCM II Process ? RCM II is a structured process that involves employees in determining the best failure management tactics for systems and equipment in their operating context ? The method is an effective approach to risk and cost reduction as well as failure management

May 1, 2002

By I. Imris

The chemical industries are using different type of catalysts, which after application usually produced many tons heap of residues. One of them is cupric oxide catalyst with high content of copper and silica. The recovery of copper from the waste has become major interest from a viewpoint of environmental protection and recycling of resources. The thermodynamic analysis and experimental results suggest that the copper from cupric oxide catalyst can be extracted by plasma reduction process. By plasma reduction process the inert slag and copper with following chemical composition: 99.04 % Cu, 0,042 % Fe could be obtained.

Jan 1, 2007

By Garth D. Kirkham

The Problem The Don deposit is a series of two sub-vertical zones that pose a number of challenges with respect to modeling and interpolation. The first challenge is that, based on data and observations, the mineralization and, more importantly, the grade is layered or banded and is stratigraphically controlled. The second challenge is that, due to the undulations of the deposit and extreme changes in dip, using a standard oriented ellipse to guide the estimation process is not appropriate and does not result in an estimate that is representative on a local scale. In order to solve this problem an adapted methodology of relative elevation modelling, has been devised to effectively model and estimate deposits faced with these challenges. Relative Elevation Designed for bedded seam and gridded surface With variable dip and vertical grade variability

May 1, 2013

By E. G. Baltuch

Natural Ventilation in mining and metallurgical processing applications is key to proper operation function. There are number of ventilator designs available to a project team or design engineers, the selection of which will affect both the type of building structure required, project costs and design performance which is difficult to rectify or re-engineer once implemented. Research and applied results, such as that performed by Air-Therm Inc., demonstrates that computational fluid dynamic simulation allows for 5 dimensional observation, analysis and optimization at significantly lowered cost than previously possible. These results have been fully implemented on a number of mining and metallurgical applications and the company continues to study, optimize and innovate as new tools become available to provide the best possible engineered solutions for particular applications.

Aug 1, 2013

There are many inherent risks in creating a mine plan for a new ore zone in an underground mine; one of such risks is the redistribution of stresses that could be a cause of instability. Using numerical modelling tools, it is possible to model the planned stope extraction sequence and evaluate the influence of mining induced stresses on the stability of remnant pillars, and use this information to remedy potential setbacks. This paper demonstrates this approach through a case study of the short-term mine plan of the Lapa mine of Agnico Eagle Mines Ltd., an underground gold mining operation near Val d?Or. Three-dimensional boundary element modelling is used to compute the stresses induced by the stope extraction sequence as planned with a longitudinal retreat mining method. The proposed methodology can be generalized to other mines that require an understanding of the stress concentrations at the pre-feasibility stage of mine design.

May 1, 2009

By E. Brouillette

Difficult operating and mining conditions such as low visibility, difficult roadbeds, fast cycling, small openings, and sharp corners create high demand for LHD manoeuvrability and operator dexterity. Operator experience and patience is especially solicited to fill the bucket rapidly and efficiently and performance can be particularly affected by the skill level of individual operators. Teleoperation and automated loading are viewed as options to improve overall equipment and operation performance in certain mining conditions. Comparative statistical measurements of autoloading performance in different production environments at Noranda demonstrate an increase in bucket filling efficiency and a reduction in filling variance, allowing LHD operation to be more consistent and within manufacturer specifications. Consequential cost savings and productivity increases are demonstrated to be transferable to other mining situations.

May 1, 2003

By P. Bacher, L. Dubourg, M. Jahazi, G. Dezaise

Effect of friction stir welding parameters and natural ageing on weld properties are reported. Using a Taguchi design of experiment, attempt is made to systematically examine the influences of the welding speed, tool rotation speed, forge force, tilt angle and pitch ratio on the weld size and ultimate tensile strength of FSWed joints. One millimetre thick plates of AA7075-T6 were welded in lap joint configuration. Samples were characterized by optical microscopy, hardness and tensile measurements. Trends suggested by the results and directions for further investigation are discussed.

Jan 1, 2006

By Reinis Sipols

AGENDA ? Introduction ? Definitions and Key features ? PEA - Preliminary Economic Assessments ? PFS ? Preliminary Fesibility Studies ? FS ? Feasibility Studies ? Costs and Risks ? Cash Flow, Economic Analysis and Reporting ? Recommendations for Improved FS accuracy INTRODUCTION ? The reporting of material information on mineral deposits has been governed by NI 43-101 legislation for almost a decade. ? The investment sector depends on the independent, professional QP to provide objective observations, comments and recommendations through all levels of geological, engineering and financial evaluation until a mine construction decision has been made.

May 1, 2013

By J. D. Corbett

The spatial coincidence of the seven anomalies is obvious, even though the self-potential is offset northward. Because the ratio, as an indicator of conductivity, is a relative estimate at best, concise interpretation is limited in almost every instance to the location of a conductor or conductor axis. When related to the initial phase of an exploration program, magnitudes and ratios similar to those obtained from any one of the methods described, would be sufficiently attractive to warrant further investigation. The compilation shown is an empirical comparison of actual field results and no emphasis has intentionally been placed on the relative merits of one method in respect to another. Too many additional factors, i.e., size, depth and conductivity of overburden, etc., that cannot unequivocally be answered, enter into such a comparison before a relative evaluation can be made.

Jan 1, 1961

By P. Hickey, G. Hubert, P. Healy

"J. S. Redpath Limited, an underground contractor with a worldwide presence, has implemented innovative techniques in various projects in Canada to shorten the development cycle. Conventional methods currently used for installing primary ground support are compared with the Australian technique of bolting and meshing with jumbos equipped with twin telescopic booms, in-cycle shotcreting, and the use of two jumbos and two scissor bolters set up side by side in wide headings. Recommendations and lessons learned are presented with the aim of providing realistic expectations with regard to development advance rates in a mining environment.RÉSUMÉ J. S. Redpath Limitée, un entrepreneur minier souterrain d’envergure mondiale, a complété plusieurs projets au Canada où des techniques novatrices ont été mises en oeuvre pour raccourcir le cycle de développement. Cet article présente une comparaison entre les méthodes conventionnelles fréquemment utilisées pour le support de terrain, la technique australienne de boulonnage et d’installation de grillage au moyen de jumbos équipés de flèches télescopiques doubles, du béton projeté appliqué durant le cycle de développement et de l’utilisation de deux jumbos et deux boulonneuses côtes-à-côtes dans des galeries de grandes dimensions. Les recommandations et les leçons apprises sont présentées dans le but de fournir au lecteur des attentes réalistes quant aux taux d’avancement du développement dans un environnement minier."

Jan 1, 2016

By Stephen Hardcastle

Presentation Outline ? Introduction ? Mine Ventilation Facts ? Ventilation-on-demand (VOD) ? Sensors/Controls ? Continuing Work ? Conclusions ? Mine ventilation engineering practices were published in 1556 in Agricola?s De Re Metallica (wind sails, bellows, etc.) That was then? This is today? Large fan installations handling >1M cfm

Nov 1, 2011

By A. Taylor

This paper considers mineral processing in zero gravity dry environments typical of asteroids or comets. The electro-dynamic separation technique using pneumatic flow systems is explored. Pneumatic delivery of solids is used because of extreme temperature changes and the possible scarcity of water. The present earth-based process and how it can be modified for these conditions is examined.

May 1, 2001

The most expensive unit operation in the beneficiation of ores is grinding. The correct design of the grinding circuit is crucial to prevent unnecessary use of energy. Proper design and evaluation of SAG grinding circuits require the specific grinding energy, which is determined experimentally. The most common tests in SAG grinding are the Drop Weight Test, from the Julius Kruttschnitt Mineral Research Center (JKMRC) in Australia, and the SAG Power Index, from MinnovEX Technologies in Canada. The application of these tests to the same ore sample commonly produces different results. The work reported here aims at comparing the application of these two tests in the determination of the specific grinding energy for sulfide copper ores from Sequeirinho and Sossego deposits, Sossego Project, Companhia Vale do Rio Doce - CVRD, in Para state, Brazil.

Jan 1, 2007

By B. Dubreuil, J. -M. Lalancette, D. Lemieux, C. Chouinard

The extraction of gold and silver has been examined via the use of mixed halogens: chlorine and bromine. The reaction was performed in a brine of sodium chloride with a small amount of sodium bromide at 40-50°C, in an atmosphere of chlorine, at atmospheric pressure. The process takes advantage of the very high reactivity of bromine towards gold, while the higher oxidation capacity of chlorine leads to gold chloride as end product with recycling of bromine. Fast reaction rates are observed along with gold recovery at the level of 95%. Chlorine-consuming common elements are removed prior to chlorination.

Jan 1, 2011

By D. Seo, P. Au, X. Husang, D. Nagy

The production of single crystal (SX) turbine blades represents the current stateof- the-art in Ni-based superalloy design. With complex casting processes and alloy composition modifications, SX superalloys exhibit superior high temperature mechanical properties to their polycrystalline counterparts. Stresses and plastic deformation can occur in SX nickel-base superalloy engine components at various stages during their manufacture and use. For examples, stresses are created during initial solidification and also during solid state processing such as shot peening, grit blasting, blending, electrodischarge machining and welding. Stresses may also be created during service due to random events such as foreign object impacts. Subsequent exposure of SX to high temperatures during solution heat treatment and brazing repair can result in recrystallization which has been shown to be detrimental to both creep rupture strength and fatigue performance of the components. It is therefore the objective of this paper to understand the recrystallization behavior of two SX superalloys, PWA 1484 and 1483, subjected to pre-stressing and subsequent heat treatments.

Jan 1, 2006

By ManhKha Trinh, Neal Pyke

Dofasco was the first company to adopt oxygen steelmaking in North America in 1954, two years after the first LD vessel installed and operated successfully in Linz, Austria. Since then, Dofasco has investigated and implemented several strategies to maximize hot metal usage and minimize overall cost. Some key strategies -low hot metal silicon, combined blowing conversion, vacuum degassing tank upgrade and BOF slag carryover control - are discussed. Post combustion, scrap preheat, carbon injection trials along with current operating philosophies are described.

Jan 1, 2004

By A. Roca, V. A. Quezada, O. A. Benavente, M. Cruells

The leaching pretreatment of copper ores is widely used in the Chilean mining industry. Agglomeration and acid curing have been identified as the most useful pretreatments. Of these, acid curing was recognized as beneficial in the dissolution of copper minerals, even in sulphides such as chalcopyrite. Extensive acid curing times have an impact on copper extraction, generate a homogeneous acid distribution in the mineral bed and benefit the inhibition of aluminum-silicate minerals (acid consumers). This document describes some of the theoretical background and results regarding the effect of acid curing in a chalcopyrite sample with 74% purity according to Qemscan analysis and a 28.5% of total copper. Leaching tests are carried out at 25, 50 and 70°C, evaluating the effect of a pretreatment on the chalcopyrite dissolution. The original sample and products generated were characterized by X-ray diffraction analysis and Scanning Electron Microscopy (SEM). The performed experiments indicate a direct relation between the effect of curing time and temperature in copper extraction. 92% of copper can be extracted in a leaching at 70°C and with 15 days of curing. Elemental sulfur, jarosite and copper polysulfide (CuS2) have been detected in leaching products. INTRODUCTION The copper extraction from minerals is a technique that has been developed for hundreds of years in the world. In 2017, the largest copper producer was Chile, exported 5.5 million tons (COCHILCO, 2018). However, in order to preserve this production level means overcoming multiple challenges. In the case of the Chilean copper deposits, the average copper grade in 2016 was 0.65%, lower than the 1% declared in 2004 (Consejo Minero, 2018). This is mainly due to the deeper of the deposits reaching sulfide mineral zones, mainly chalcopyrite. Traditionally, these sulfurized zones ore are treated through concentration by flotation and subsequent pyrometallurgical treatments. However, for some copper companies it is complex to process by this alternative, due to the high costs and high rates of water consumption. The mineral resources of these companies are known as "low-grade sulfides" and do not allow, economically, the treatment of these minerals through concentration by flotation. This is how hydrometallurgy becomes an alternative for the treatment of this type of deposits. In addition, several companies have hydrometallurgical plants, which would allow the operational continuity of these plants.

Jan 1, 2019