Search Documents

By T. Mulpeter, G. Deschênes

Sadiola Gold Mine is an open pit operation located in Mali and owned by Anglogold Ashanti Ltd, Iamgold Corporation and the State of Mali. A conventional cyanidation process (cyanidation/CIP) treats 15,000 tpd (of a mixture of oxide and sulphide ores) at an average grade of 3 g/t Au. In 2002, the increasing tonnage of sulphides caused an increase in production costs and a decrease in gold extraction (from 95% to 70-76%). Because of the short retention time of the leach circuit (18 hours) and the refractory nature of the sulphides, gold leaching kinetics are critical. A laboratory investigation was initiated to evaluate actual plant practice and identify a means of improving the gold leaching rate. The study was conducted on a "soft" sulphide gold sample containing 4.96 g/t Au, 0.4 g/t Ag, 2.5% pyrite, 1.2% arsenopyrite, and 0.2% pyrrhotite with a P80 of 74microns. Pre-leaching significantly influenced the gold leaching rate. A short pre-leach (2 hours) performed at pH 8, a DO of 8 ppm, and with 300 g/t lead nitrate added at the start or the end, produced the preferred conditions. Pre-leaching for more than 2 hours was detrimental to gold extraction. The cyanide concentration had to be maintained at 450 ppm NaCN to reach a maximum gold extraction within the retention time of the circuit. A maximum extraction of 81.3% Au was obtained in 20 hours (leach residue at 0.97 g/t Au). A high level of dissolved oxygen in the pre-leach was not of any benefit. Extension of gold leaching beyond 20 hours indicated that all leachable gold had been extracted by that time. Plant modifications were made to allow leaching of oxides and sulphides in separate circuits. Treatment of oxide ores is now performed at a higher rate. Sulphides are processed at a lower throughput, with 300 g/t lead nitrate, to allow a retention time of 22 hours. Combined throughput remains the same, and total gold recovery has increased from 76% to 80% for an additional gold production of 16,000 ounces per year.

Jan 1, 2005

By M. Piboule et J. M . Charbonneau, C. Picard

In the western part of the Chapais syncline (Abitibi-east, Quebec), the lava flows belonging to the Haliy Formation separate in two distinct sequences. The basal sequence contains prophyri tic metabasalts of calc-alkaline af f inity overlain by porphyritic metatrachyandesites and metatrachytes of alkaline to shoshonitic affinity. The upper sequence contains porphyritic metabasalts similar to those of the basal sequence along with highly potassic metaandesites trending to a subalkaline affinity. A geochemical study of trace and REE elements established that the composition of these lava flows results from a mixing or contamination process. The primitive tholeiitic liquids which are enriched in LREE were modified by the addition of a crustal contaminant enriched in Y, Zr, Th and K20. The magmatic liquids resulted from successive steps in the admixing process, evolved by fractionated crystallization. The mechanism of gradual admixing seems to be the major cause of the observed ea le-alkaline characteris ties and may also be the cause of the alkaline to shoshoni tic affinity in those lavas. The tendency to differentiation by fractional crystallization reveals the tholeiitic character of the primitive liquids.

Jan 1, 1984

By J. W. Hohn

The precipitation of Fe(III) to form ferrihydrite in the presence of arsenic is the United States EPA's Best Demonstrated Available Technology for treating arsenic-containing hydrometallurgical solutions and waste streams. This technology has been widely adopted throughout the world and developments have been well reviewed. The adsorption and long-term stability of ferrihydrite can be improved by co-precipitating Fe(III) and Al(III) together to form an aluminum-modified ferrihydrite. Arsenate adsorption into ferrihydrite and modified ferrihydrite as a function of pH, Fe/As or (Al+Fe)/As mole ratio, and the initial As(V) concentration is presented and compared. The results of long-term aging of both adsorbents at 70°C for over a year are also summarized.

Jan 1, 2006

By Frederic Benard

THE Ontario Refining Company, Limited, wholly-owned subsidiary of The International Nickel Company of Canada, refines the entire blister copper output of the latter's Copper Cliff smelter. Prior to 1936, the blister was cast in 460-lb. cakes at the smelter, loaded on open cars, and transported by rail to the refinery, a distance of approximately 1 1/4 miles. Here the cakes were transferred to the plant narrow-gauge system, charged to furnaces, and re-melted. This procedure necessitated the operation of holding furnaces and casting machines at the smelter -extensive re-handling-and melting down of a cold charge at the refinery. Transfer of the copper in molten form direct from converters to anode furnaces promised a considerable reduction in costs, and this possibility was investigated. As a result, a portable holding furnace, or hot-metal car, was designed and constructed. It was placed in operation in July, 1936, to be followed a year later by three additional units of slightly modified design. Figure 1 shows the original car, and Figure 2 the lacer type. With four cars in service, operations were placed on an all 'hot-metal' basis.

Jan 1, 1938

Stellite-6 coatings were formulated on two Ni-base superalloys, namely Superni 75 and Superni 600, by a shrouded plasma-spray process, and the oxidation behaviour of these coatings has been investigated in air and in an aggressive environment of Na2SO4- 60%V2O5. Accelerated oxidation tests were conducted in a silicon-carbide tube furnace under cyclic conditions at an elevated temperature of 900°C for 50 cycles. Each cycle consisted of 1 h heating and 20 min cooling in air. A thermogravimetric technique was used to approximate the oxidation kinetics. The corrosion scales were characterised by XRD, SEM/EDAX and EPMA analysis. It has been observed that the coatings nearly followed the parabolic rate law of oxidation. Overall weight gain conceived in air was just 51% of that in the aggressive environment in the case of coated Superni 75, whereas in case of coated Superni 600, the cumulative weight gain in air was found to be one-third of that in the Na2SO4-60% V2O5 atmosphere. Furthermore, the coating showed very good adherence to both of the substrates during the course of air oxidation, whereas some superficial cracks were observed near the edges of the specimens during the molten salt induced oxidation. XRD analysis revealed the presence of phase-like CoO, CoCr2O4 and Cr2O3 in the oxide scales, which are reported be protective against high-temperature oxidation. The XRD results were further supported by SEM/EDAX and EPMA.

Jan 1, 2005

By M. M. Helm

Samples sourced from the Goldstrike property in Nevada USA, have been evaluated in terms of their preg-robbing capacity and the physical structure of the graphitic carbon component in the carbonaceous gold ore. The study highlights a wide range in preg-robbing capacity between samples collected from the Betze-Post open pit and Rodeo underground mine. The physical structure of the graphitic carbon was assessed using Raman spectroscopy, and is found to play an important role in influencing preg-robbing behaviour. Differences observed in the physical structure of graphitic carbon are thought to be the result of hydrothermal events that occurred at Goldstrike.

Jan 1, 2011

By A. Allaire, J. Torrealba-Vargas, R. Welyhorsky

Early testwork was carried out to select the plant process design criteria and flowsheet selection. Additional testwork was carried out during the feasibility study to support the optimization of the plant design criteria. The test results showed that the recovery of gold was not very sensitive to grind size in the range of 75 to 105 microns. An additional result was that the presence of lead nitrate did not improve the kinetics of gold leaching. This conclusion was supported by the low content of sulphides in the ore. It was also found that the presence of lead nitrate increased copper dissolution, producing the potential for an increase of copper reporting to electrowinning, which is detrimental to the overall gold recovery process. The use of oxygen in leaching was investigated to increase leach kinetics. The results of leaching tests to compare using oxygen instead of air indicated that, due to the improved leach time, it was possible to reduce the number of leaching tanks from twenty four (24) to twenty (20).

Jan 1, 2011

By Bertrand Robinson

Great advances have been made in rubber-lined pumps for the pumping of mill pulps. The Canadian Allis Chalmers alone report ov.er 300 such pumps put into service during the past four years. Pumps in which both the casing and the impeller are rubber covered have proved most economical in handling the usual run of mill pulps, effecting large savings in power, maintenance, and shutdown costs. For the handling of pulps containing comparatively large, sharper edged /articles, rubber-lined casings with hard iron impellers have been developed by the pumping departments of Hollinger and Noranda. These rubber-iron combination pumps show an appreciable reduction in overall pumping costs as compared with the all-rubber and the all-iron pumps. The power efficiency is lower in rubber-iron than in all-rubber pumps but higher than in the all-iron pumps, with lower replacement costs due to the cheap iron impellers used. Where continuous operation is essential, however, and duplication of units to take care of shutdown time for replacement of parts is not within the expenditure budget of the company, all-rubber pumps are being used t0 a greater extent. As in all items pertaining to milling operations, the economics of the situation must be studied as closely as the technical details, to arrive at the most advisable practice.

Jan 1, 1939

By Jerry Ran

Many large underground mines using the open stoping method have changed their primary applications of consolidated rock fill (CRF) to paste or consolidated hydraulic fill due to considerations of demand in infrastructure and equipment, system reliability, backfill capacity and material sources. However, some smaller or even large mines still use or consider using CRF for backfill purpose due to factors such as capital expenditure, availability or suitability of other fill types or in some cases local regulatory requirements. As demands on CRF applications diminish among major mining companies, there is a lack of recent literature on application of CRF to open stoping in design and operation. There are several methods being used for fill strength design. Results from these methods have been successfully applied to paste or hydraulic fill. However, the design strength for CRF is much higher than that determined by use of these widely accepted methods. In operation, CRF preparation and placement have significant impacts on the quality of placed CRF and therefore the mining performance. This paper reviews the current fill design methods and their applications to open stoping with presentation of the bench marking data, presents fill failure cases and various CRF preparation and placement arrangements and discusses quality assurance and control programs.

Jun 1, 2012

The comminution circuit at Tarkwa Gold Mine was commissioned as a Single Stage SAG mill operated in closed circuit with hydrocyclones designed to process 4Mtpa. The circuit was later expanded by adding a secondary ball mill in closed circuit with hydrocyclones with a view to treat 12Mtpa. The change in the circuit configuration and assigning the low aspect ratio SAG mill for primary grinding application makes the Tarkwa experience unique in terms the optimisation strategy and operating philosophy. This paper reports the findings from a series of surveys performed on this plant. The surveys reported include data obtained when the SAG mill was operated as a single stage mill in closed circuit with hydrocyclones and also SABC mode under two different feed conditions. The differences in operating philosophy between the initial single stage SAG circuit and the current SAG/Ball mill circuit are discussed.

Jan 1, 2012

By A. O. Orumwense

Mill circumferential speed, the number of passes of pulp through the grinding chamber, media type, size and filling ratio were investigated in an attempt to determine how to effectively grind copper concentrates in a stirred mill. The stirred mill product fineness was enhanced to some extent by decreasing media size, high media filling, and an increased number of passes of the pulp through the grinding chamber. Shape also plays a major role in grinding media effectiveness, with spherically shaped media producing a finer size. The fineness of the product increases with increasing power consumption but the method of energy transfer is very important in energy utilization. The effect of the mill parameters on copper flotation was evaluated. Copper recovery was influenced by grinding media size, mill speed and the number of pulp passes through the grinding chamber.

Jan 1, 2006

By S. F. Guo, B. W. Zheng, X. L. Huang, S. W. Qi

"The study of mechanical characteristics of rock discontinuities under different shear deformation velocities is an important premise of rock slope dynamic response analysis. According to disposing and calculating the experimental results of previous research about peak shear strength of rock discontinuities under different shear deformation velocity of constant normal loading, the law of influence of shear velocity on the total friction angle is studied. Based on the research results, it can be found that the total friction angle of rock joint specimens varies in the form of negative logarithm with the variation of shear deformation velocity. It’s also indicated that the total friction angle of rock joints decreases with the increase of shear deformation velocity for rock joints of relative strong homogeneity and isotropy. However, the total friction angle of rock joints increases with the increase of shear deformation velocity for rock joints of relative strong heterogeneity and anisotropy and the latter amplitude of increase is less than the former amplitude of decrease. The physical property and microscopic geometry of rock joints play an important effect on the increase or decrease tendency and amplitude variation of total friction angle with the increase of shear deformation velocity.INTRODUCTIONThe rock slope dynamic response is largely restricted by rock discontinuities. Hence the study of dynamic characteristics of rock discontinuities, especially the dynamic shear characteristics is an important premise of rock slope dynamic response analysis (Qi et al., 2007). Seismic load is both dynamic load and cyclic load (Liu et al., 2011). Under the dynamic and cyclic shearing actions of seismic load, the rock slope which is stable under the condition of static load may slide along the rock discontinuities whose shear strength reduce and then the earthquake landslides occur. The strength degradation and deformation mechanism of rock discontinuities under the dynamic and cyclic shearing actions is one of the key problems to be solved in the work of earthquake prevention and control of engineering slope. Based on the above understanding, predecessors conduct some researches which focus on the shear behavior mechanical characteristics of rock joints under cyclic shearing actions (Plesha, 1987; Hutson & Dowding, 1990; Jing et al., 1992, 1993; Huang et al., 1993; Qiu et al., 1993; Homand et al., 2001; Lee et al., 2001; Jafari et al., 2003; Liu et al., 2011, 2013). However, there are a few researches about the mechanical characteristics of rock joints under different shear deformation velocities because of the restriction of shear apparatus. Crawford and Curran (1981) conducted a series of one-way cyclic direct shear tests on four kinds of natural rock joints under different shear deformation velocities varying from 0 to 200 mm/s. The tests showed that at low normal stresses the peak shear strength of soft rock joints exhibited an increase up to a certain velocity, after which it remained essentially constant. For rock joints of intermediate hardness, the peak shear strength was essentially independent of shear deformation velocity; whereas for hard rock joints, the peak shear strength of which showed a significant variation with the shear deformation velocity. Jafari et al. (2003) carried out a series of conventional triaxial tests on artificial rock joints of regular saw-tooth shape with axial loading rate from 0.05 mm/s to 0.4 mm/s."

Jan 1, 2015

By T. Lamb

There are many honor stories about aluminum in the marine environment and many are not based on facts, so they are myths. Myths must be addressed before progress can be made. This paper attempts to dispel the myths and state the facts. A common perception is that aluminum ships cost significantly more than steel ships. This paper illustrates that even though the cost of the aluminum structure is over 50% more than the steel structure, an "equivalent" aluminum naval ship can be built within 7% of the acquisition price of a steel ship. This is possible because of the cascading benefits of the aluminum ship's significantly lighter weight. Aluminum ships also have a life-cycle cost advantage over steel ships because of reduced maintenance and fuel cost savings.

Jan 1, 2011

By H. Son

The three-dimensional (3D) reconstruction of as-built industrial plant models plays an important role in revamping planning, maintenance planning, and preparation for dismantling during the lifecycle of industrial plants. Recently, the 3D reconstruction of existing industrial plants was conducted using laserscan data to make surveying processes more efficient. However, the current 3D reconstruction process from laser-scan data is still limited due to the need for significant human assistance. Although a great deal of effort has been made to efficiently reconstruct 3D as-built industrial plant models, the presence of objects?such as equipment, pipelines, and valves of different sizes and shapes?in existing industrial plants significantly increases the complexity of laser-scan data and makes automating the reconstruction process more challenging in practice. The purpose of this study is to propose a knowledge-based approach for the 3D reconstruction of as-built industrial plant models from unstructured laser-scan data. First, pipelines were extracted from laser-scan data based on surface curvature information and knowledge about pipelines' sizes from existing piping and instrumentation diagrams (P&ID). Once entire pipelines were extracted, they were modeled based on skeleton features. Then, the remaining objects were clustered and grouped separately via the region grouping process. Afterward, clustered objects were retrieved and modeled based on global feature-based matching from the 3D database. Finally, the resulting model was checked to ensure that it was well-reconstructed according to the information regarding the relationships among objects abstracted from the existing P&ID. The preliminary results on actual industrial plants show that integrating knowledge into the reconstruction steps played an important role in the proposed approach and that this approach obtained accurate as-built industrial plant models from unstructured laser-scan data. The proposed approach could be successfully utilized to assist in many applications during the lifecycle of industrial plants.

Aug 1, 2013

By G. W. Neumann, J. R. Schnarr

The lead-zinc-copper-silver ores mined by Brunswick Mining and Smelting Corporation Limited at their No. 12 underground mine and No. 6 open-pit operation, and treated by distinct concentration processes in separate plants, present difficult metallurgical problems because of the extremely fine dissemination of the valuable minerals with pyrite and pyrrhotite. The problem of concentration is further complicated, in the No. 12 ore, by the presence of a varying content of graphitic carbon. This paper describes the milling of No. 12 ore and the production of copper, lead and zinc concentrates by differential flotation.

Jan 1, 1971

By J. Kempken, R. Hagmann, C. -P. Reip, W. Hennig

The CSP technology symbolizes a highly productive process for the cost-effective production of steel grades with a range of sophisticated properties comprising both the inner quality of hot strip, its surface formation as well as the relating technological characteristics. Thanks to extensive development work undertaken during the last 15 years, the range of steel grades that can be produced was continuously expanded and the process technology optimized. The present paper describes the ongoing development work concerning the production of higher-strength, microalloyed pipe steels. The resulting hot strip, due to the associated thickness and the potential pipe diameters, is particularly suited for being processed to HFI-welded pipes. Based both on ferrite-pearlite as well as very fine-grained, ferrite-bainite hot-strip microstructures, strength levels of up to grade API X80 can be realized. It can be demonstrated that hot strip produced in a CSP plant has very good toughness values at temperatures down to -60°C and can even make application with required sour-gas resistance possible.

Jan 1, 2005

By Dave M. Jakelski, Gerhard W. Heinrich, Peter F. Wells, Daniel F. Suarez, Jamie B. Beauchamp

"A need for increased copper concentrate production and for less nickel contamination in that concentrate at Falconbridge's Strathcona Concentrator during 1993 required the installation of a third flotation column and improvements in the operation of the existing circuit. Innovations in wash water distributor and launder design were fundamental in achieving objectives on a new 3 meter diameter column. Minnovex plug-type spargers were tested on a 2.1 meter diameter column in order to reduce maintenance requirements. The paper details the measures taken to enhance column flotation circuit performance and the results obtained.IntroductionFalconbridge's Strathcona Mill receives 10% of the ore feed from a rich copper zone in the Strathcona mine. This ore typically grades 7% copper and 1 % nickel and, because of its high copper content, it is processed in a separate circuit ('C' circuit) which consists of conventional grinding, rougher flotation with the concentrate being treated with lime to pH 12.3 and cyanide followed by column flotation. The columns are operated with mechanical flotation scavengers and the scavenger concentrate is returned to the column feed. Testwork conducted in 1991 showed that the original flotation column (Column 2) could only produce 5.5 mtph of concentrate with less than 0.5% nickel (Figure 1).Between 1991 and spring of 1993, production was increased at times by open circuiting the scavengers. Metallurgical improvements were obtained by improving the wash water distributor of Column 2 and by wash water sprays in conventional cells (1 ). However, the scavenger concentrate assayed 0. 7 -0.8% nickel and was not acceptable for long term operation. When Copper ore production targets were significantly increased for 1993, it became clear that an additional flotation column was required. The new flowsheet employs mechanical scavenger cells on the column tails as in Column 2 circuit (Figure 2). A -parallel configuration was chosen as pulp solids fraction has been shown to be a critical variable and the second column in series would receive a lower density feed."

Jan 1, 1994

By V. I. Ryaboy, V. P. Kretov, I. V. Ryaboy, E. D. Shepeta

This paper studies the features of known and newly synthesized dialkyldithiophosphates and reagents with thioamide groups when separating copper-containing and arsenic-containing minerals in the flotation of skarn-scheelite-sulphide ore at the Primorskaya concentration plant. The optimization of dialkyldithiophosphate collectors was based on the study of their surface activity at the liquid-gas interface and estimated hydrophobic abilities. The flotation experiments show that the selectivity of action of the reagent increases with an increase of its surface activity and a reduction of hydrophobic ability when separating chalcopyrite and arsenopyrite. IMA-225-5 was proposed as a more efficient dialkyldithiophosphate collector, which increases the recovery of copper by 2.8% compared to the industrially used collector IMA-I413. Selection of the optimal structure for reagents with thioamide groups (derivatives of thionocarbamate and thiourea) was carried out according to their acidity and the presence of hydrophilic particles in their structure. Calculations were performed depending on the pH of the solution of chalcopyrite to determine the optimum reagent sorption and to further optimize the structures of these reagents. The tests with reagents with thioamide groups show an increase in copper recovery by 3-4% together with a significant increase of arsenic content compared to IMA-225-5. As a stronger collector with thioamide groups, it was recommended to use sample 234, which belongs to the thiourea derivatives. IMA-225-5 was recommended for industrial tests at the Primorskaya concentration plant. Thus, this study has shown that using dialkyldithiophosphate is more appropriate if it is necessary to increase the selectivity of separation of copper-containing and arsenic-containing minerals, and using reagents with thioamide groups, or their combinations with dialkyldithiophosphates, is more appropriate if it is necessary to increase the recovery of copper or the quality of copper concentrate with less selectivity of the process.

Jan 1, 2016

By T. A. Utigard

To improve recoveries of Ni, Cu and Co in the Inco flash furnace, a new operating concept was investigated. By adding sufficient coke to form a supernatant coke layer, a reducing barrier would form allowing for improved reduction of descending oxidized sulfide mineral particles formed in the flame. The objective of this investigation was to study the kinetic mechanism and efficiency of the coke layer to produce a sulfur deficient matte. The mechanism and rate of carbon reduction of each of the phases formed in the flash flame, i.e. sulfides and oxysulfides were investigated by means of X-ray visualization tests. Graphite-slag reduction was also conducted for comparison purposes. In the case of slag, poor wettability and the formation of a gas film on the surface of the carbon reductant are often blamed for limiting the reaction surface area that ultimately results in poor reaction kinetics. The X-ray visualization tests confirmed that matte and oxysulfide wet coke better than slag and that the rates of reduction of matte and oxysulfide are faster than that of slag.

Jan 1, 2005

By F. Y. Hsiao, H. C. Kao

Underground excavation in hard rock is normally stable at shallow depth except for wedge failure. However, the excavation depth is rapidly increasing recently. In high overburden stress condition, the integrity of rock would be destroyed with degrading rock strength. Therefore, understanding both the peak and the post-peak strengths of hard rock are necessary to assess the tunnel stability at depths. The characteristic of the post-peak strength is seldom studied in Taiwan in the past. Various estimation methods for the post-peak strength degradation were briefly reviewed in the paper. Based on the Geological Strength Index (GSI) system is widely used in the determination of the rock mass strength, the quantitative residual GSI system was adopted to estimate the possible strength degradation for a hydraulic tunnel in Taiwan. The Mohr-Coulomb model (no strength degradation) and the post-peak strength degradation model (strain softening model) were used to simulate the excavation of the case tunnel at different depths. The analyses demonstrate that the tunnel is in stable condition at 600m of depth. And the effect of the postpeak strength degradation on tunnel deformation is progressively significant with increasing tunnel depth. Approximate 3-5 times of increase in crown settlement and horizontal convergence would occur when post-peak strength degradation are considered at 2400m of depth. Severe tunnel deformation may endanger the tunnel stability. Modeling results reveal that the post-peak strength degradation has a great effect on tunnel stability under high overburden stress condition, which should not neglect in deep tunnel design.

Jan 1, 2015