Search Documents

By T. Niedoba

Coal as an energetic raw material is characterized by many features that determine its quality. The data concerning coal are usually treated as independent values, despite the fact that this kind of approach is not always appropriate. In the paper the dependencies between sulfur contents and volatile components in coal and particle size and density were analyzed. The method of ordinary kriging is applied to experimental data to describe this relationship; this method can be used for particles of any size and density. An example of the application of this technique is presented for energetic coal Type 31, originating from one of the Polish hard coal mines in Upper Silesia. Results from ordinary kriging are in good agreement with experimental results. Similar analyses can be performed for other properties of coal material, such as ash content, Roga number, and moisture. On the basis of the data obtained by ordinary kriging, a more comprehensive multidimensional model is described, which can characterize certain deposits or strata from which the analyzed materials originate. This is superior to basing the model only on experimental data, which often is limited by size of the sample. The results obtained by ordinary kriging applied to various types of coal would allow more precise analysis of individual properties of the studied materials and increase the ability to determine significant differences between them. This method can be also applied to other types of mineral raw materials, such as copper ore.

Aug 1, 2013

By Y. Hayashi, A. Fuwa

To analyze zinc vaporization kinetics of zinc smelting slag in the ISP furnace, reduction reaction rate of zinc oxide from ZnO-FeOx-CaO-SiO2 slag system with CO-CO2-Ar gas mixtures has been measured by a therm o-gravim etric apparatus at various ZnO content, Pco, and temperature. The reduction rate was measured under a chemical reaction control in the initial three minutes where surface zinc content can be assumed constant. Through the reaction rate dependency analysis on ZnO contents, Pco and temperature, discussion has been made on its reaction mechanistic information in terms of rate coefficient, adsorption/desorption mechanism and activation energy.

Jan 1, 2008

By J. D. Bosman, L. J. Gardner

"The Bushveld Complex is a large layered igneous intrusion, located in the northern parts of the Republic of South Africa. The complex hosts the largest known reserves of Platinum Group Metals in the world. On the western limb of the complex, mining of the Merensky economic horizon and UG2 chromitite layer has been conducted for many years by several mining companies, including Impala Platinum Limited. Over the past decade, Impala has planned a new generation of greenfield vertical shafts, commencing with comprehensive geological and geotechnical studies. As part of the geotechnical studies, numerous tests have been conducted to quantify the mechanical properties of the various near-reef rock types. These tests include point load tests conducted in the field, as well as uni-axial compressive strength, triaxial compressive strength, and Brazilian disc tensile strength tests conducted in specialist laboratories. The authors have compiled an extensive database containing a large number of tests for different rock types, ranging from felsic Anorthosite to mafic Pegmatoid. The database was analysed to quantify the mechanical properties and values for Mohr Coulomb and Hoek Brown failure criteria for each rock type typically exposed by mining. The paper will provide a data set of rock mechanical properties typically used in numerical modelling and other design processes. Using the significant number of tests available, data describing the variability of the various parameters will be included."

Jan 1, 2015

By Douglas A. Sloan

AN INCENTIVE or bonus system of payment is commonly used for mine labour. The incentive rates are usually based on the variable units of production, such as dollars per foot of drift advance or cents per ton of ore broken. Portions of the work that must be done to achieve the units of ?production are independent of the production unit and tend to be fixed work for the shift or for the job, irrespective of the production achieved. This fixed work has considerable influence on the equity of incentive rates. The effect of fixed work is to accelerate the loosening or tightening of rates if the production task is over-achieved or under-achieved, and of increasing the loosening of rates loosely set and the tightening of rates tightly set. This gearing of mine contract rates is the reason why changes in conditions, materials, equipment, or methods will change the incentive earnings to a greater degree than would normally be expected. Obviously, therefore, care should be taken in the setting of the task for incentive rates as the gearing makes an inequitable rate even more inequitable.

Jan 1, 1958

By J. Graham Eby

"This paper describes the development and some typical applications of Wemco's large-capacity flotation machines, the No. 120 and the No. 144, with volumes of 300 and 500 cubic feet, respectively. During the 1960's, it became obvious that low-grade orebodies would be mined at high tonnage rates - plants and grinding mills would be larger, which would create a demand for larger flotation equipment. To meet this demand, Wemco developed a single-mechanism, 300-cubicfoot cell, having five times the volume of the standard No. 66 cell. The average production rate of the No. 66 cell on porphyry copper ore was 100 tpd per cell; and it was our intention that the No. 120 (300-cu. ft) cell would handle 500 tpd per cell, with at least equal metallurgical results and power consumption per ton. The success and industry acceptance of the No. 120 cell has since led to the development of a larger cell, the No. 144, having a volume of 500 cubic feet."

Jan 1, 1972

By H. M. Woodrooffe

IT IS WELL KNOWN that chrysotile asbestos from various occurrences exhibits varied physical properties and certain differences in chemical corn position, both of which conditions may have an important bearing on the industrial utilization of the fibre. The usefulness of a harsh fibre in the manufacture of asbestos cement products and of low-iron fibre for certain electrical uses are examples. It is also .possible to obtain a fibre with a texture too harsh and brittle to be of economic value. Much research into the structure of the mineral and to a lesser degree observations relating the water of combination to certain physical properties have ?been reported. This paper is an attempt to show that the pyrolysis of ?chrysotile takes place in three stages and that the conditions of pyrolysis are peculiar to the fibre and may afford some clue to the variations in physical properties of asbestos fibres which affect their utilization.

Jan 1, 1956

By A. Mehinrad, F. Rafia

"The Dez River flows from the Zagros Mountains into the great Khuzestan plain, Southwest of Iran. The 203 m high Dez Dam is a double curvature thin concrete arch dam, with a Pulvino, founded on thick bedded to massive conglomerate of Bakhtiary Formation, mainly horizontal and very less jointed at the dam site. Construction work was completed in 1963, creating a reservoir with a total storage volume of 3’315 million m3. The dam body, with some 350’000 m3 volume and (W/H=1.1/1.0), is the dominant feature of the project.Geological and geotechnical studies at the dam site started in 1957 and continued during the whole period of dam construction. Simultaneously, two extensive programs of laboratory testing were carried out in New York and Milan.Most of the results were recorded in the project design documents and in two very well-known papers of Talobre et. al. (1964) and Dodds (1966), however, no detail results are available for most of tests.In order to estimate geomechanical parameters of the rock mass foundation for numerical modeling of the dam body and its foundation, reassessment of the in-situ and laboratory test results using the recent rock mechanics methods was required.This paper explains how the outcomes of those tests, performed more than 50 years ago, were reevaluated and how the definitions and parameters presented in the project reports were re-interpreted using the recent rock mechanics concepts and definitions. Also, the results of classification of Bakhtiary conglomerate using GSI system and application of Hoek & Brown failure criterion for estimating rock mass parameters have been described.INTRODUCTIONThe Dez River flows from its headwaters in the Zagros Mountains into the great Khuzestan plain. Just before entering the plane, the river passes through a narrow, steep gorge that is about 17 km long. The Dez Dam is located at the entrance to this gorge, some25-km upstream of the city of Dezful and 150-km upstream from the provincial capital Ahwaz (Figure 1)."

Jan 1, 2015

By T. Mulpeter, G. Deschênes

Sadiola Gold Mine is an open pit operation located in Mali and owned by Anglogold Ashanti Ltd, Iamgold Corporation and the State of Mali. A conventional cyanidation process (cyanidation/CIP) treats 15,000 tpd (of a mixture of oxide and sulphide ores) at an average grade of 3 g/t Au. In 2002, the increasing tonnage of sulphides caused an increase in production costs and a decrease in gold extraction (from 95% to 70-76%). Because of the short retention time of the leach circuit (18 hours) and the refractory nature of the sulphides, gold leaching kinetics are critical. A laboratory investigation was initiated to evaluate actual plant practice and identify a means of improving the gold leaching rate. The study was conducted on a "soft" sulphide gold sample containing 4.96 g/t Au, 0.4 g/t Ag, 2.5% pyrite, 1.2% arsenopyrite, and 0.2% pyrrhotite with a P80 of 74microns. Pre-leaching significantly influenced the gold leaching rate. A short pre-leach (2 hours) performed at pH 8, a DO of 8 ppm, and with 300 g/t lead nitrate added at the start or the end, produced the preferred conditions. Pre-leaching for more than 2 hours was detrimental to gold extraction. The cyanide concentration had to be maintained at 450 ppm NaCN to reach a maximum gold extraction within the retention time of the circuit. A maximum extraction of 81.3% Au was obtained in 20 hours (leach residue at 0.97 g/t Au). A high level of dissolved oxygen in the pre-leach was not of any benefit. Extension of gold leaching beyond 20 hours indicated that all leachable gold had been extracted by that time. Plant modifications were made to allow leaching of oxides and sulphides in separate circuits. Treatment of oxide ores is now performed at a higher rate. Sulphides are processed at a lower throughput, with 300 g/t lead nitrate, to allow a retention time of 22 hours. Combined throughput remains the same, and total gold recovery has increased from 76% to 80% for an additional gold production of 16,000 ounces per year.

Jan 1, 2005

By J. W. Hohn

The precipitation of Fe(III) to form ferrihydrite in the presence of arsenic is the United States EPA's Best Demonstrated Available Technology for treating arsenic-containing hydrometallurgical solutions and waste streams. This technology has been widely adopted throughout the world and developments have been well reviewed. The adsorption and long-term stability of ferrihydrite can be improved by co-precipitating Fe(III) and Al(III) together to form an aluminum-modified ferrihydrite. Arsenate adsorption into ferrihydrite and modified ferrihydrite as a function of pH, Fe/As or (Al+Fe)/As mole ratio, and the initial As(V) concentration is presented and compared. The results of long-term aging of both adsorbents at 70°C for over a year are also summarized.

Jan 1, 2006

By Frederic Benard

THE Ontario Refining Company, Limited, wholly-owned subsidiary of The International Nickel Company of Canada, refines the entire blister copper output of the latter's Copper Cliff smelter. Prior to 1936, the blister was cast in 460-lb. cakes at the smelter, loaded on open cars, and transported by rail to the refinery, a distance of approximately 1 1/4 miles. Here the cakes were transferred to the plant narrow-gauge system, charged to furnaces, and re-melted. This procedure necessitated the operation of holding furnaces and casting machines at the smelter -extensive re-handling-and melting down of a cold charge at the refinery. Transfer of the copper in molten form direct from converters to anode furnaces promised a considerable reduction in costs, and this possibility was investigated. As a result, a portable holding furnace, or hot-metal car, was designed and constructed. It was placed in operation in July, 1936, to be followed a year later by three additional units of slightly modified design. Figure 1 shows the original car, and Figure 2 the lacer type. With four cars in service, operations were placed on an all 'hot-metal' basis.

Jan 1, 1938

By M. M. Helm

Samples sourced from the Goldstrike property in Nevada USA, have been evaluated in terms of their preg-robbing capacity and the physical structure of the graphitic carbon component in the carbonaceous gold ore. The study highlights a wide range in preg-robbing capacity between samples collected from the Betze-Post open pit and Rodeo underground mine. The physical structure of the graphitic carbon was assessed using Raman spectroscopy, and is found to play an important role in influencing preg-robbing behaviour. Differences observed in the physical structure of graphitic carbon are thought to be the result of hydrothermal events that occurred at Goldstrike.

Jan 1, 2011

Stellite-6 coatings were formulated on two Ni-base superalloys, namely Superni 75 and Superni 600, by a shrouded plasma-spray process, and the oxidation behaviour of these coatings has been investigated in air and in an aggressive environment of Na2SO4- 60%V2O5. Accelerated oxidation tests were conducted in a silicon-carbide tube furnace under cyclic conditions at an elevated temperature of 900°C for 50 cycles. Each cycle consisted of 1 h heating and 20 min cooling in air. A thermogravimetric technique was used to approximate the oxidation kinetics. The corrosion scales were characterised by XRD, SEM/EDAX and EPMA analysis. It has been observed that the coatings nearly followed the parabolic rate law of oxidation. Overall weight gain conceived in air was just 51% of that in the aggressive environment in the case of coated Superni 75, whereas in case of coated Superni 600, the cumulative weight gain in air was found to be one-third of that in the Na2SO4-60% V2O5 atmosphere. Furthermore, the coating showed very good adherence to both of the substrates during the course of air oxidation, whereas some superficial cracks were observed near the edges of the specimens during the molten salt induced oxidation. XRD analysis revealed the presence of phase-like CoO, CoCr2O4 and Cr2O3 in the oxide scales, which are reported be protective against high-temperature oxidation. The XRD results were further supported by SEM/EDAX and EPMA.

Jan 1, 2005

By A. Allaire, J. Torrealba-Vargas, R. Welyhorsky

Early testwork was carried out to select the plant process design criteria and flowsheet selection. Additional testwork was carried out during the feasibility study to support the optimization of the plant design criteria. The test results showed that the recovery of gold was not very sensitive to grind size in the range of 75 to 105 microns. An additional result was that the presence of lead nitrate did not improve the kinetics of gold leaching. This conclusion was supported by the low content of sulphides in the ore. It was also found that the presence of lead nitrate increased copper dissolution, producing the potential for an increase of copper reporting to electrowinning, which is detrimental to the overall gold recovery process. The use of oxygen in leaching was investigated to increase leach kinetics. The results of leaching tests to compare using oxygen instead of air indicated that, due to the improved leach time, it was possible to reduce the number of leaching tanks from twenty four (24) to twenty (20).

Jan 1, 2011

By Bertrand Robinson

Great advances have been made in rubber-lined pumps for the pumping of mill pulps. The Canadian Allis Chalmers alone report ov.er 300 such pumps put into service during the past four years. Pumps in which both the casing and the impeller are rubber covered have proved most economical in handling the usual run of mill pulps, effecting large savings in power, maintenance, and shutdown costs. For the handling of pulps containing comparatively large, sharper edged /articles, rubber-lined casings with hard iron impellers have been developed by the pumping departments of Hollinger and Noranda. These rubber-iron combination pumps show an appreciable reduction in overall pumping costs as compared with the all-rubber and the all-iron pumps. The power efficiency is lower in rubber-iron than in all-rubber pumps but higher than in the all-iron pumps, with lower replacement costs due to the cheap iron impellers used. Where continuous operation is essential, however, and duplication of units to take care of shutdown time for replacement of parts is not within the expenditure budget of the company, all-rubber pumps are being used t0 a greater extent. As in all items pertaining to milling operations, the economics of the situation must be studied as closely as the technical details, to arrive at the most advisable practice.

Jan 1, 1939

By Jerry Ran

Many large underground mines using the open stoping method have changed their primary applications of consolidated rock fill (CRF) to paste or consolidated hydraulic fill due to considerations of demand in infrastructure and equipment, system reliability, backfill capacity and material sources. However, some smaller or even large mines still use or consider using CRF for backfill purpose due to factors such as capital expenditure, availability or suitability of other fill types or in some cases local regulatory requirements. As demands on CRF applications diminish among major mining companies, there is a lack of recent literature on application of CRF to open stoping in design and operation. There are several methods being used for fill strength design. Results from these methods have been successfully applied to paste or hydraulic fill. However, the design strength for CRF is much higher than that determined by use of these widely accepted methods. In operation, CRF preparation and placement have significant impacts on the quality of placed CRF and therefore the mining performance. This paper reviews the current fill design methods and their applications to open stoping with presentation of the bench marking data, presents fill failure cases and various CRF preparation and placement arrangements and discusses quality assurance and control programs.

Jun 1, 2012

The comminution circuit at Tarkwa Gold Mine was commissioned as a Single Stage SAG mill operated in closed circuit with hydrocyclones designed to process 4Mtpa. The circuit was later expanded by adding a secondary ball mill in closed circuit with hydrocyclones with a view to treat 12Mtpa. The change in the circuit configuration and assigning the low aspect ratio SAG mill for primary grinding application makes the Tarkwa experience unique in terms the optimisation strategy and operating philosophy. This paper reports the findings from a series of surveys performed on this plant. The surveys reported include data obtained when the SAG mill was operated as a single stage mill in closed circuit with hydrocyclones and also SABC mode under two different feed conditions. The differences in operating philosophy between the initial single stage SAG circuit and the current SAG/Ball mill circuit are discussed.

Jan 1, 2012

By A. O. Orumwense

Mill circumferential speed, the number of passes of pulp through the grinding chamber, media type, size and filling ratio were investigated in an attempt to determine how to effectively grind copper concentrates in a stirred mill. The stirred mill product fineness was enhanced to some extent by decreasing media size, high media filling, and an increased number of passes of the pulp through the grinding chamber. Shape also plays a major role in grinding media effectiveness, with spherically shaped media producing a finer size. The fineness of the product increases with increasing power consumption but the method of energy transfer is very important in energy utilization. The effect of the mill parameters on copper flotation was evaluated. Copper recovery was influenced by grinding media size, mill speed and the number of pulp passes through the grinding chamber.

Jan 1, 2006

By S. F. Guo, B. W. Zheng, X. L. Huang, S. W. Qi

"The study of mechanical characteristics of rock discontinuities under different shear deformation velocities is an important premise of rock slope dynamic response analysis. According to disposing and calculating the experimental results of previous research about peak shear strength of rock discontinuities under different shear deformation velocity of constant normal loading, the law of influence of shear velocity on the total friction angle is studied. Based on the research results, it can be found that the total friction angle of rock joint specimens varies in the form of negative logarithm with the variation of shear deformation velocity. It’s also indicated that the total friction angle of rock joints decreases with the increase of shear deformation velocity for rock joints of relative strong homogeneity and isotropy. However, the total friction angle of rock joints increases with the increase of shear deformation velocity for rock joints of relative strong heterogeneity and anisotropy and the latter amplitude of increase is less than the former amplitude of decrease. The physical property and microscopic geometry of rock joints play an important effect on the increase or decrease tendency and amplitude variation of total friction angle with the increase of shear deformation velocity.INTRODUCTIONThe rock slope dynamic response is largely restricted by rock discontinuities. Hence the study of dynamic characteristics of rock discontinuities, especially the dynamic shear characteristics is an important premise of rock slope dynamic response analysis (Qi et al., 2007). Seismic load is both dynamic load and cyclic load (Liu et al., 2011). Under the dynamic and cyclic shearing actions of seismic load, the rock slope which is stable under the condition of static load may slide along the rock discontinuities whose shear strength reduce and then the earthquake landslides occur. The strength degradation and deformation mechanism of rock discontinuities under the dynamic and cyclic shearing actions is one of the key problems to be solved in the work of earthquake prevention and control of engineering slope. Based on the above understanding, predecessors conduct some researches which focus on the shear behavior mechanical characteristics of rock joints under cyclic shearing actions (Plesha, 1987; Hutson & Dowding, 1990; Jing et al., 1992, 1993; Huang et al., 1993; Qiu et al., 1993; Homand et al., 2001; Lee et al., 2001; Jafari et al., 2003; Liu et al., 2011, 2013). However, there are a few researches about the mechanical characteristics of rock joints under different shear deformation velocities because of the restriction of shear apparatus. Crawford and Curran (1981) conducted a series of one-way cyclic direct shear tests on four kinds of natural rock joints under different shear deformation velocities varying from 0 to 200 mm/s. The tests showed that at low normal stresses the peak shear strength of soft rock joints exhibited an increase up to a certain velocity, after which it remained essentially constant. For rock joints of intermediate hardness, the peak shear strength was essentially independent of shear deformation velocity; whereas for hard rock joints, the peak shear strength of which showed a significant variation with the shear deformation velocity. Jafari et al. (2003) carried out a series of conventional triaxial tests on artificial rock joints of regular saw-tooth shape with axial loading rate from 0.05 mm/s to 0.4 mm/s."

Jan 1, 2015

By T. Lamb

There are many honor stories about aluminum in the marine environment and many are not based on facts, so they are myths. Myths must be addressed before progress can be made. This paper attempts to dispel the myths and state the facts. A common perception is that aluminum ships cost significantly more than steel ships. This paper illustrates that even though the cost of the aluminum structure is over 50% more than the steel structure, an "equivalent" aluminum naval ship can be built within 7% of the acquisition price of a steel ship. This is possible because of the cascading benefits of the aluminum ship's significantly lighter weight. Aluminum ships also have a life-cycle cost advantage over steel ships because of reduced maintenance and fuel cost savings.

Jan 1, 2011

By H. Son

The three-dimensional (3D) reconstruction of as-built industrial plant models plays an important role in revamping planning, maintenance planning, and preparation for dismantling during the lifecycle of industrial plants. Recently, the 3D reconstruction of existing industrial plants was conducted using laserscan data to make surveying processes more efficient. However, the current 3D reconstruction process from laser-scan data is still limited due to the need for significant human assistance. Although a great deal of effort has been made to efficiently reconstruct 3D as-built industrial plant models, the presence of objects?such as equipment, pipelines, and valves of different sizes and shapes?in existing industrial plants significantly increases the complexity of laser-scan data and makes automating the reconstruction process more challenging in practice. The purpose of this study is to propose a knowledge-based approach for the 3D reconstruction of as-built industrial plant models from unstructured laser-scan data. First, pipelines were extracted from laser-scan data based on surface curvature information and knowledge about pipelines' sizes from existing piping and instrumentation diagrams (P&ID). Once entire pipelines were extracted, they were modeled based on skeleton features. Then, the remaining objects were clustered and grouped separately via the region grouping process. Afterward, clustered objects were retrieved and modeled based on global feature-based matching from the 3D database. Finally, the resulting model was checked to ensure that it was well-reconstructed according to the information regarding the relationships among objects abstracted from the existing P&ID. The preliminary results on actual industrial plants show that integrating knowledge into the reconstruction steps played an important role in the proposed approach and that this approach obtained accurate as-built industrial plant models from unstructured laser-scan data. The proposed approach could be successfully utilized to assist in many applications during the lifecycle of industrial plants.

Aug 1, 2013