Search Documents

By L. J. Cunningham

Introduction The property of Rouyn Merger Gold Mines, Limited, is in Rouyn and Joannès townships, Western Quebec, seven miles east of the town of Rouyn. Traversing it is the east-west trending Cadillac-Bouzan fault. Diamond drilling in 1944 and 1945 along a shear zone south of the fault indicated an ore deposit lying at the contact between sedimentary and volcanic rocks and dipping approximately 60° to the northwest. In the summer of 1945 it was decided to sink a shaft to investigate the indicated ore zone. In the immediate vicinity of the deposit, bed-rock is overlain by clay beds, in some places as much as 70 feet thick. Consequently, possible shaft sites were limited to those locations where overburden would not be excessive. The most favourable site was about 125 feet to the south of the ore zone as projected vertically from bed-rock to the surface. Accordingly, it was decided to sink the shaft at this point, with an inclination of 60° N. W., paralleling the dip of the ore zone.

Jan 1, 1948

By R. K. Rajamani

Discrete Element Method simulation of charge motion in ball, SAG and autogenous mills has become a standard for design of mill internals, power draft evaluation, etc. Both two-dimensional and three-dimensional codes are being used. The two-dimensional code dominates the user market since the code completes a simulation in one or two hours. On the other hand, three-dimensional codes have been in the domain of specialists who can handle the complexity of the code and have access to parallel computing hardware. For the first time, this barrier is overcome via computing with graphic processing units (GPU). Commodity graphics cards now allow parallel computation with hundreds of processors. It is shown that the computational time has been reduced by a factor of fifty using GPU computing. Hence, SAG charge simulation results in three dimensions are achievable in a few hours using affordable desktop machines. The GPU computing shown here enables the three dimensional simulation into a manageable daily task for mill designers and researchers. On the technical side, the simulations can be elevated to a higher level of complexity to simulate breakage and transport. First, the speedup factor of fifty is established for the Nvidia GeForce GTX 580 graphics card. Next, four simulation tasks, consisting of AG, SAG and ball mills are reported. The simulation of AG and SAG mills are completed in less than 8 hours. The ball mill simulation with 1.25 million spheres is completed in 27 hours. In the near future, as the graphic card hardware advances the compute time can be halved.

Jan 1, 2012

By Bunting S. Crocker

This paper reviews the trends in the past two years in autogenous grinding throughout the world. It covers rock grinding in South Africa, Sweden, Canada, the United States, Finland and Germany. To properly orient the discussion on this subject, the paper attempts to define and classify the scope of autogenous comminution. As this is a relatively new subject, there is often considerable confusion regarding the various practices, which sometimes differ widely. By clarifying the types and forms, we hope to help clear up this con-fusion. Autogenous grinding is being carried out, throughout the world, either in mills grinding in water or solution or in dry mills using air classification to remove the finished material. The wet grinding, particularly, can be divided into: (1) (2) (3) Primary autogenous grinding, or "run-of-mine" grinding. Secondary autogenous grinding or semi-autogenous grinding or rock pebble grinding. Combination processes. -This covers plants in which pebbles made in the primary mill are re-moved and used as grinding media for fine grinding in secondary mills.

Jan 1, 1963

By Robert D. Brown, Robert B. Parsons

"The mining industry may have survived the October 28 federal budget relatively unscathed, but the same certainly cannot be said of the petroleum sector-and many mining men are left wondering if their industry will be the next one to be singled out for special attention, as federal and provincial governments seek additional revenues and pursue nationalistic or provincial policies.Higher taxes, higher prices, a potpourri of ""incentives"", and a -""Canadianization"" policy mark the principal features of the new National Energy Program released by the government along with Finance Minister MacEachen's budget address.This month, Tax Notes examines the federal budget. with appropriate emphasis on the National Energy Program and its possible future implications forthe Canadian resource industries.IntroductionMost of the Canadian mining industry (tar sands miners excepted) heaved a sigh of relief on the evening of October 28, 1980, as Finance Minister MacEachen confounded the prophets in his budget address by not raising personal or corporation taxes and by making only relatively modest changes in the general tax system. Instead, he concentrated on a sweeping new energy policy. Unfortunately for that important sector of Canada's mining industry which is involved in mining the country's vast tar sands reserves, either now or in the future, the National Energy Program that was introduced along with the budget 'has serious implications."

Jan 1, 1981

By L. E. Fischer

The background for the 630-million-dollar-plus iron ore project at Kudremukh is outlined. The system and plants for mining, crushing, concentrating, transporting via a slurry pipeline, filtering and shiploading 7.5 million metric tons of iron ore per year are fully described. The mode of operation and the problems encountered in such a transfer of North American technology to developing countries are analyzed. Difficulties encountered during construction are discussed and the progress milestones made over a two-year period are enumerated.

Jan 1, 1979

By K. Yamaguchi

"This Precious metals content copper scrap is treated with a copper smelting process, and copper and precious metals are recovered. The precious metal lost in the slag is increasing with increasing of treated scrap amount. To determine the portion of the precious metals chemically dissolved and that associated with the mechanically trapped matte in the slag will be a key factor to improve the recovery of those metals. The distribution of precious metals between copper matte and FeOx-SiO2 slag phases is determined at 1300 oC and a fixed partial pressure of SO2 of 0.1 atm for the matte grades from 40 to 70 mass% of copper. The distribution ratios show a tendency to increase when the grade of matte is increased. In addition, the solubility of platinum and rhodium in the FeOx-SiO2-CaO slag under the air and the solubility of platinum in the FeOx-SiO2 slag equilibrated with a pure platinum or the Pt-Cu alloy were determined at 1300oC in the range of oxygen partial pressure from 10-9 to 10-7. The solubility of platinum and rhodium in the slag tends to increase with increasing content of copper in the slag and oxygen partial pressure. INTRODUCTIONThe stringency of the supply and demand of platinum group metal (PGM) intensifies by localization for resources and increase of the demand for PGM, furthermore, smelting and the recycling of PGM in the nonferrous smelting process take an important role. Scrap containing a precious metal for the purpose of collection of PGM is treated by copper smelting recently. With increase of the treatment amounts, loss of PGM in slags is the serious problem.In considering of PGM loss in slags, knowledge of the distribution behavior for PGM between slag and matte phases or slag and copper phases and the PGM solubility in slags is important. The distribution ratios of silver and gold between the FeOx-SiO2 slag and the Fe-Cu matte were reported by Roghani (Roghani et al., 2000), Shinha (Shinha et al., 1985) and Takeda (Takeda et al., 1993) However, there is no data for the PGM distribution ratio. On the other hand, the PGM solubility in slags was reported by Sano (Sano et al., 1997) However, there is very few report for the solubility of PGM in the nonferrous smelting slags."

Jan 1, 2012

By C. H. van Eendenburg

"Installation of a 3.6 km long raw coal conveyor in the Balmer open pit was undertaken to improve over-all haulage efficiency. This paper covers the rationale behind this project, system design and construction aspects and initial operating experiences. The majority of the construction work was performed by our own personnel. Where feasible, used equipment was installed to reduce capital cost and facilitate a tight construction schedule.BackgroundWestar Mining Ltd's Balmer Mine is located in the British Columbia Rockies, just outside of the town of Sparwood in the southeastern corner of British Columbia. The open pit mine, which has been in operation since 1969, currently produces about 6 million clean tonnes of coal per year, mostly for the metallurgical coal export market. Run-of-mine coal tonnages total between 9 and 9.5 million annually and waste removal volumes exceed 30 million bank cubic metres.The mine is a truck/shovel operation; loading equipment includes nine electric shovels, five front-end loaders and a hydraulic backhoe. The truck fleet consists of 40 units of 154-tonne, 181-tonne and 315-tonne capacity. The newer 154-tonne trucks are used for coal haulage for which they have been equipped , with tailgates to maximize their coal carrying capacity."

Jan 1, 1990

By T. Holmes, S. Davison

"A surge bin at Agrium’s Vanscoy potash operations has been plagued with flow, wear, and corrosion issues since being built in 1967. The culprits? The bin’s carbon-steel construction, geometry, and the resultant funnel-flow pattern are the root causes. An investigation and cost analysis indicated that hopper redesign and retrofit would increase production and reduce maintenance and capital costs. The retrofitted bin provides safer, more reliable operation and has a much longer predicted working life. Using this example, the authors describe bulk-solids-flow theory and highlight the importance of customizing bulk-material-handling-system design using appropriate flow properties to improve reliability, safety, and cost effectiveness.RÉSUMÉ Depuis sa construction en 1967, un réservoir intermédiaire de l’exploitation de potasse Vanscoy d’Agrium connaît des problèmes de débit, d’usure et de corrosion. Les responsables ? La construction en acier ordinaire du réservoir, sa géométrie et la structure de débit en résultant au niveau de la carotte en sont les causes fondamentales. Une étude et une analyse des coûts indiquaient que la restructuration et la rénovation de la trémie permettraient d’augmenter la production et de réduire les coûts d’entretien et en capital. Un réservoir rénové permet de renforcer la sécurité ainsi que la fiabilité de l’exploitation, et sa durée d’activité prévue en est augmentée. En se fondant sur cet exemple, les auteurs de l’article décrivent la théorie du débit de matières solides en vrac et insistent sur l’importance de personnaliser la conception du système de manutention des matériaux en vrac à l’aide de propriétés rhéologiques adaptées afin d’améliorer la fiabilité, la sûreté et la rentabilité.INTRODUCTIONIn early 2013, Agrium’s Vanscoy Potash Operations (VPO) engaged Jenike & Johanson Ltd. (J&J) to provide testing, consulting, and structural engineering services related to proposed modifications to the 270 t special standard product surge bin, which Agrium planned to undertake during a two-week shutdown in August 2013. The bin, which had been plagued with flow, wear, and corrosion issues for its entire working life, was essential for the continuous operation of two of VPO’s compaction plants and for efficient dispatching to loadout. The bin often experienced product hang-ups, clumping on the walls, and plugging at the hopper outlet. Two recent unscheduled mill shutdowns had been partially attributed to flow issues in the bin due to clumping and product plugging up at the screws. These problems increased maintenance costs, limited production capacity, and degraded product quality. Holes and paper-thin sections in the bin walls discovered during a 2013 inspection revealed the potential for major hot material leaks or even structural failure. Either issue would stop plant operations until the bin could be repaired or bypassed. Clearly, the bin cone had reached the end of its life and required replacement."

Jan 1, 2018

By M. R. Campbell

"IntroductionON THE LAST DAY of December, 1951, a half-century of steel production was completed in the open hearth department of Dominion Iron & Steel, Limited, in Sydney, Nova Scotia.During that period, almost every known variation of basic steel making practice was used in working out a steel making process which would overcome the difficult metallurgical problems imposed by the use of Cape Breton coal and Wabana ore.This paper is presented as a brief review of these steel making practices, setting forth the fundamental metallurgical factors involved in their success or failure.Establishing the IndustryThe story of steel production at Sydney is closely interwoven with that of coal. The steel industry owes its inception to a desire on the part of the Dominion Coal Company, which was incorporated in 1893, to improve its marketing position by increasing sales of slack coal and providing a year-round demand for its product. Accordingly, the Dominion Iron and Steel Company, Limited, was incorporated on March 30th, 1899, with Mr. H. M. Whitney -who was President of the Dominion Coal Company -as its first President. The new Company was given powers to manufacture and process iron and steel, and to mine all minerals, including coal.A strong inducement to the industry was the bounty offered by the Dominion Government for the production of both iron and steel."

Jan 1, 1952

By A. Hashempour, D. Javani

"Selection of an optimal bit is a critical issue in drilling engineering. Specific energy (SE) and Cost per Foot (CPF) are the most common methods for evaluation of bit efficiency and optimal bit selection. The major shortfall of both methods is that they do not directly account for geological and geomechanical parameters of formations being drilling. In this paper, results of using the two foregoing methods are compared using Formation Drillability (FD) method, which directly accounts for geological and geomechanical parameters of a formation. This method combines various geological and geomechanical parameters and yields a dimensionless parameter indicating the formation drilling hardness (drillability). Results of this study show that the amount of energy, cost and time spent for drilling a unit volume / length of an identical formation may vary in different wells. This is due to the fact that geological and geomechanical characteristics of a formation may vary among wells and even within short intervals of a single well. Therefore, an optimal bit may not be appropriately selected, if drilling and economical parameters are the only factors considered and the formation geological and geomechanical specifications are ignored.INTRODUCTIONMany authors such as Bilgesu, Al-Rashidi, Aminian, and Ameri (2000) and Clegg (2006) conducted research in the evaluation of bit performance and optimum bit selection. Almost all of them tried to establish a good relationship based on geomechanical parameters. Primary examples are the research done by Ubaldi (1999), Macini, Magagni, Da Dalt, and Valente (2007)."

Jan 1, 2015

By Tracey Bodnarchuk, Philipp Mirzoev

Sulfate balance control is a common problem for zinc plants. Roast-leach-electrowin plants are mostly concerned with the over-generation of sulfates while for the HudBay direct leach plant both extremes are possible including potential necessity to buy sulfuric acid to replenish a sulfate-depleted circuit, which makes the problem doubly important. Quantitative methods were applied at the HudBay plant to analyze sulfate generation/depletion based on a local sulfur balance and sulfate extraction calculation in the leach circuit, using a Pb-tie method. Main factors were established influencing sulfate generation/depletion, including the critical role of Pb and pyrite. Regression analysis proved to be effective and allowed the quantitative prediction of Pb concentrations necessary to reach the equilibrium for the sulfate balance. This in turn provided a firm basis for a sulfate-control strategy realized through concentrate blend correction, which allowed the plant to fine-tune sulfate generation/depletion effectively reducing economic consequences of excessive/deficient sulfate generation.

Jan 1, 2015

By R. D. Brown

The first step in achieving a rationalization of Canada's crazy patch-work quilt of mining taxes and policies was achieved with the release last November of a major federal-provincial report on the taxation of the Canadian mining industry. The Report, prepared by a group of federal and provincial civil servants, sets out a concise and informative discussion of the major taxation and incentive issues facing the mining industry, and puts forward major recommendations for more rational and moderate taxation policies. It will be considered by federal and provincial Finance and Resource Ministers for possible action by the respective governments. The Report was prepared in response to a directive from the federal and provincial First Ministers in February 1978 to review the federal and provincial taxation of the resource areas. Although the Report is more successful in identifying problems rather than concrete solutions, and reflects some continuing differences of opinion between the governments involved, it does represent an important first step in a comprehensive review of our resource tax policies. This article summarizes the Report, which is some sixty pages in length. Although a detailed discussion of it is beyond the scope of this article, the report itself is recommended reading for those concerned about the current state of the Canadian mining industry.

Jan 1, 1979

By Constantin D. Pitis

?Demand-side measure" means a rate, measure, action or program undertaken to conserve energy or promote energy efficiency?? (BCUC, 1996) In actual economical environment, business sustainability requires high-efficiency technological processes. That is why the efficiency concept has to be present at all levels of industrial activities. Nowadays, some purchasing decisions are still driven predominately by the purchase price, in spite of the evidence that such price represents up to 5 % to 7 % of the total costs of ownership with full consequences of energy efficiency and the impact on total ownership costs. The paper presents essentials of converter types and basics of the Global Efficiency (GEff) Concept that has been promoted over the last few years in South African industries (Pitis et al., 2006/7). GEff concept is proven as a useful tool used on price-efficiency decisions. Theoretical and technical aspects of this concept were substantiated with case studies. First part presented in this paper will describe how GEff concept was used on price ? efficiency decisions when single input or direct converters and systems (considered as low value equipments) have been replaced. Besides the impact of energy savings and new innovative developments, the paper suggests general other benefits of: ? Technical and economical performance improvements and competitiveness of mining corporations to international standards; ? Defusing incipient energy crisis in the sector; ? Improving environmental conditions; ? Creating new job opportunities in mining sector. Proposed concept in this paper could be further developed as models of improving companies? corporate energy policies.

May 1, 2010

By Jun Deng

The aim of this paper is to study the scientificity and reliability of three coal gas indices used to predict coal fire disasters, namely Graham?s ratio, CO/CO2 ratio, Litton ratio and their different characteristics and service conditions. Data from a programmed temperature experiment were applied to check their veracity and accuracy. Each index performed well in detecting the level of a fire. We conclude that it is better to redefine the definition through experimentation before applying a given index. Integrated analysis of the results can provide reliable reference data for predicting spontaneous combustion of coal.

Aug 1, 2013

By A. G. Matyas

Process improvements which have reduced the lead content of slag from the Brunswick lead blast furnace are described. Microscope examination and electron microprobe analyses, supported by the results of slag settling and viscosity tests, showed that typically about 70% of the lead in the lead blast-furnace slag was present in the form of entrained prills of metallic lead. The total lead content was found to increase with the magnetic susceptibility of the slag. Measurements in the furnace settler indicated the presence of a magnetite-rich layer between bullion and slag, arising from high magnetite levels in the slag. This layer was believed to inhibit the settling of entrained lead from the slag. Tracer tests showed that the average slag residence time in the settler was less than 2 minutes. Improvements in coke quality and sizing, which led to a reduction in the slag magnetite content, and the installation of a larger settler and a continuous Roy tapper, have all contributed to a significant decrease in the slag lead content.

Jan 1, 1977

The primary (sulphide) resources at Aphrodite are refractory in nature, requiring an oxidation process stage to be introduced to facilitate extraction of the gold. The company is investigating the use of pressure oxidation (POX) as the oxidation method for processing of high grade gold bearing concentrate it plans to produce at Aphrodite. POX has been used extensively around the world for the past 30 years and continues to be the favoured option for a number of refractory gold plants currently in the design and construction stages. Initial pressure oxidisation testing investigated the effect of temperature, pressure and grind size on a bulk flotation concentrate prepared from Alpha lode material. The concentrate averaged 47.3 g/t gold and was prepared from a composite of core samples averaging 1.49 g/t gold. Sub-samples of the concentrate were subjected to POX for 1 hour resulting in rapid oxidation during this very short period. Testing undertaken showed that there was a significant increase in sulphide oxidisation at higher temperature (220°C) and pressure (2,500 k/Pa) for the two grind sizes (75 and 20 microns) evaluated. The proposed flowsheet, OPEX and CAPEX are critical aspects for project development.

Jan 1, 2014

By DONALD E. BARNETT

Since the days of early settlement ew Brunswick has produced a variety of industrial minerals but it is perhaps only the recent discoveries of significant reserves of potash that have elevated the meaning of industrial minerals in their contribution to the provincial economy. With potash production commencing in July 1983, the role of industrial minerals will increase significantly to the value of mineral production in the province.

Jan 1, 1984

By Tapio Leskinen, Jouko Koskinen, Timo Nlltti, Lappalainen Seppo, Pentti Vanninen

"The Courier 300 on-stream analysis system manufactured by Outokumpu has now been in operation at five of the company's concentration plants long enough to give a reliable basis for closer examination of the benefits achieved in control of these processes. The first system was installed at the Pyhiisalmi mine at the end of 1967. Since November 1970, two analyzers have been in operation at Pyhiisalmi feeding the assay data to a process computer which controls the whole plant and does the optimization of the process. In October 1970 the Courier 300 analysis system was installed at S. T. O. LESKINEN J. KOSKINEN the Keretti concentrator of the Outokumpu mine, followed soon by installations at the Vihanti Mine in May 1971, at the new Vuonos mine in November J 971 and at t he Kotalahti mine in December 1971. Since installation of the Courier analysis systems, considerable improvements have been achieved in the control and the economy of the plants. Immediate knowledge of the changes in the process and the possibility for rapid action has resulted in evener production and higher capacity and recovery. The recovery has been increased most significantly at the Vihanti concentrator, which operates on a complex ore. Consumption of chemicals has been reduced at all concentrators. Due to the fact that process control and partly also bilance analysis are not achieved by conventional methods any more, it has been possible to reduce the personnel of the laboratories drastically. Two of the plants, viz. the Pyhiisalmi and the Vuonos concentrators, are computercontrolled. The Vuonos concentrator started operation in January 1972 under computer control from the very beginning. The Pyhiisalmi concentrator has been computer-controlled since 1970. The Courier 300 analysis system was described in detail at the AIME Centennial Annual Meeting (1971). In this paper, less attention is paid to the analysis system. Only the sampling system of the Courier 300 is described in more detail. In the development of sampling equipment, effective use has been made of the company's wide knowledge of the problems involved and the test field offered by its concentrators. The sampling equipment includes secondary samplers and six basically different types of primary samplers, with which most sampling situations can be managed."

Jan 1, 1973

By Krishna Parameswaran

"This paper discusses energy use and conservation in the primary copper industry and illustrates eco-efficiency considerations, using select examples of practices at ASARCO LLC, an integrated primary copper producer and others in the industry that promote eco-efficiency. The World Council for Sustainable Business Development first publicized the concept of eco-efficiency at the Rio Earth Summit in 1992. Eco-efficiency is a management concept linking environmental and economic performance and is aimed at generating added value for a business through, among other things, increased resource and energy conservation and reduced environmental impacts throughout the life cycle of the product or service. This concept differs from sustainable development in that focus is only on economic and environmental factors and does not include social considerations. In the metal mining and processing context, this added value can be realized by implementing practices that promote conservation of water and mineral resources, conservation of energy, minimization of waste, reduced emissions and effluents and increased recycling. The examples from the primary copper industry used to illustrate eco-efficiency considerations include: water and energy conservation in mineral processing, adoption of flash and bath smelting processes, emission reduction and process improvement associated with fire-refining, implementation of green chemistry in electrorefining, promoting product stewardship initiatives and fostering renewable energy project on disturbed mined lands.INTRODUCTION ASARCO LLC (Asarco) was organized in 1899 as the American Smelting And Refining Company. Originally a consolidation of several lead-silver smelting companies, it evolved over the years into an integrated producer of primary non-ferrous metals, including copper, lead and zinc and associated co-products. Grupo México, S.A.B. de C.V acquired Asarco in 1999. Today, Asarco is a vertically integrated producer of primary refined copper and associated co-products such as gold, silver, molybdenum, selenium and tellurium. Asarco operates three open-pit mines and mills, two leach, solvent extraction-electrowinning (SX-EW) plants and a copper smelter in Arizona and a copper refinery in Texas."

Jan 1, 2017

By V. Gregoire

THE DEVELOPMENT by the Iron Ore Company of Canada of the Quebec-Labrador mining project, which eventually led to 'Iron Ore in 1954', involved, from the start, several distinct undertakings. Among them, the most important were: The construction of a 360-mile railway, linking Knob Lake with Seven Islands. The erection of a railway terminal, and harbour facilities, at Seven Islands itself. The building of an entire townsite at Schefferville (formerly Knob Lake) The construction of two hydroelectric plants; and, finally, The development of a sufficient number of orebodies to enable a production of 10 to 15 million tons of ore a year. Since these phases of the project have already been the subject of previous discussions, this paper will not elaborate further on them but will rather concern itself with a brief outline of the Company's current mining practices.

Jan 1, 1958