Search Documents

By M. Bryson, S. Broom-Fendley, A. E. Brady, W. Dawes, G. Beer, N. Sehlotho, S. Al-Ali, F. Wall

The Songwe Hill Rare Earth Element (REE) Project in Malawi is a near surface carbonatite-hosted deposit with synchysite and apatite as the key REE bearing minerals. A strong focus has been placed on understanding the REE mineralogy of the Songwe Hill carbonatite as REE mineralogical characterization is a crucial component at all steps, ranging from exploration to production, in the development of REE deposits. Extensive mineralogical work has been completed at Camborne School of Mines (CSM), Natural History Museum (NHM) London, British Geological Survey (BGS), Nottingham, Aberystwyth University, Wales, Mintek, South Africa, and SGS Inc. Canada (SGS). The following analytical techniques were used: scanning electron microscopy (SEM), electron microprobe analysis (EMPA), laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS), and QEMSCAN®. The detailed studies have demonstrated that while synchysite is light-REE enriched as expected, apatite, abundant in all stages of carbonatite emplacement at Songwe, is anomalously enriched in mid- to heavy-REE relative to apatite in other carbonatite deposits. The distribution of REE within synchysite and apatite at Songwe has had important implications for the direction of the metallurgical work with respect to the behaviour of light and heavy REE through the flotation and hydrometallurgical stages of the flow sheet.

Jan 1, 2014

By J-P. Rossetti, A. Guerin, M. Jaboyedoff, L. Baillet, A. Mariscal, J. D'Amato, D. Hantz

"The processes leading to the fall of rock compartments from rock walls are poorly known as well as their velocity. It ensues that quantitative prediction of the failure time for a rock compartment which is presently stable, is not possible by a purely geomechanical approach. However a quantitative probabilistic prediction of rockfalls at the scale of a rock wall is possible if the spatial-temporal rockfall frequency can be determined or estimated (Hantz, 2011). For a better knowledge of failure processes and frequency, rockfalls have been detected in several rock walls, using annual terrestrial laser scanning, allowing comparison of the frequencies in different geological conditions. For one of these rock walls, the spatial detection have been completed by a precise dating of the events, using a quasi-continuous photographic survey (one photo every 10 mn), allowing the study of the influence of meteorological factors.The precise dating of rockfalls has been carried out for the Saint-Eynard cliff which towers above a residential area of the town of Grenoble (French Alps). The South-East facing cliff consists in bedded limestone gently dipping North-West and located at an elevation between 850 m and 1100 m. The surveyed zone is about 750 m large and 250 m high. Between 01/02/2013 and 26/11/2013, 65 rockfalls ranging between 0.01 m3 and 20 m3, have been detected by diachronic comparison of laser scanner data and dated by comparison of photographic images. The temperature at the elevation of the cliff has been calculated from the temperature measured (every 5 mn) at a meteorological station located at an elevation of 245 m and 2.5 km away from the cliff, using a temperature gradient of 0.003°C/m (D’Amato et al., 2014). The precipitation were measured 900 m away from the cliff at an elevation of 469 m. Different meteorological conditions have been defined: (a) “freeze” qualifies days with negative mean temperature (but with a thaw period, except for two days); (b) “thaw” qualifies days with positive mean temperature, but following a freeze day; (c) “rain” qualifies days with precipitation.Table 1 shows the rockfall temporal frequency for the different meteorological conditions. It appears that the frequency is about 6 times higher the freeze days, 2.5 higher the thaw days and 3 times higher the rain days than days without freeze, thaw or rain."

Jan 1, 2015

By S. B. Ballantyne, D. R. Boyle

"Detailed studies have been conducted on the dispersion of uranium in stream waters and sediments around various types of mineralization and hitherto unexplained anomalous areas in the Okanagan Valley and Highland region of south-central British Columbia. These studies were part of the jointly funded and planned Federal-Provincial Uranium Reconnaissance Program of the Geological Survey of Canada and the British Columbia Ministry of Energy, Mines and Petroleum Resources. Statistical analysis of regional data indicates that U in stream waters and sediments varies considerably for different rock types, thus affecting data interpretation. In addition, the data demonstrate a poor correlation between U in stream waters and their associated sediments which can be largely accounted for by variations in climate and water and sediment composition. Regional trends in the distribution of U can be explained in terms of the above secondary factors as well as primary metallization phenomena.Significant correlations between U and F, and U and Mo can be explained by certain magmatic and mineral-forming processes. U shows little correlation with other base metals.The dispersion characteristics of U in the vicinity of Miocene "" basal type "" mineralization ; uraniferous pegmatite terranes, anomalous lineaments in granitic terranes and high-background volcano-sedimentary areas are discussed. Highly anomalous U concentrations in waters and sediments may not always be indicative of mineralization, and guidelines for interpretation require a sound knowledge of the geological and secondary processes operative in the area."

Jan 1, 1980

By M. Sahoo, P. Burke, Y. Fasoyinu, J. P. Thomson

The effects of grain refinement, mold temperature and chemical composition on the hot tearing resistance of aluminum alloys 535.0 and 206.0 has been studied by pouring constrained rod castings in metal molds. In addition, two prototype components that could be used in automotive applications were also poured from both alloys by gravity tilt-pour and low pressure permanent mold casting processes. This paper summarizes the results and issues encountered during the casting trials. It was shown that grain refinement and mold temperature ::::: 400°C reduced, and sometimes eliminated hot tear cracks in both alloys. The two prototype engineering components could be cast successfully from both alloys in metal molds. The metallurgical issues related to molten metal treatment and processing temperatures were well controlled. However, issues related to the control of hot tearing, casting and mold design must be addressed in future studies to guarantee the production of defect free castings.

Jan 1, 2006

Evolution of Maintenance Practices. Mechanization processes in underground mining operation became stronger in the 70?s - 80?s. Did maintenance practices changed over the years ? What are the the major differences of today?s practices? Speaker, Robert Hamilton Working at different positions into maintenance organization since over 25 years, Robert has accumulated a various and rich experience of ways to maintain equipment. He started as mechanic on construction projects and open pit mines. Early in his career Robert had supervision's responsabilities. He started in open pit operation (QCM) and after in underground operation with Lac Minerals, working at Bousquet, Doyon and Louvicourt mines, as U/G mechanical foreman and mechanical general foreman, and Maintenance superintendant with Cambior . He also experienced the underground mines equipments supplier's side working with Sandvik Canada.

Feb 1, 2008

By J. Ouellet

The design of hydrostatic liner for a deep potash mine shaft in Saskatchewan poses tremendous technological challenges. Technology has evolved to a point where one could consider a new innovative approach to hydrostatic liner design. But there is still a place for conventional technologies such as cast iron tubbings. As will be discussed in this paper, improvement to manufacturing process, installation procedures and even new materials can bring this technology to an excellent level of performance. With the spur of new projects in the potash industry of Saskatchewan, the authors worked in various shaft liner designs from the conceptual stage through to the construction phase. They were either directly leading the design work on some of these projects or acting as an external reviewer on others. Most of these shaft liner designs involved cast iron tubbing technology and ground freezing. The major challenge in sinking potash shafts in Saskatchewan is to go through a water-bearing ground formation under high pressure, known as the Blairmore or Manville fm. The only proven stabilizing technology for these formations is ground freezing. For a potash shaft, dry shaft conditions are highly desired, so a fully waterproof hydrostatic liner is required. All the existing potash mine shafts in Saskatchewan, except for two with composite steelconcrete lining, used the cast iron tubbing technology. Two new shaft tubbing liners have been constructed recently, one in the Athabasca Basin and one for a potash mine in Saskatchewan. When the authors began working on these new projects, what became quickly evident is that the technological knowhow for designing and constructing tubbing liners was no longer available within Canada and that the past construction methods used to sink tubbing lined shafts was obsolete. The tubbing liner for the shafts sunk in the sixties were designed either by German or British companies. In both of these countries only few tubbing lined shafts were sunk in last 40 years and the technology used in the sixties was not improved. There are only few countries where tubbing is routinely produced and installed: China, Russia, Ukraine and Poland. Out of these countries Poland is the one where this technology is the most advanced. The authors, working in close collaboration with engineers from Poland, attempted to rebuild this knowledge for the mining industry in Canada. This process involved thorough analysis of old technical reports, literature review and study of current polish design and construction practices as well as site visits of existing shafts. Through actual construction experience, some lessons were learned as well as ideas for improvements. In this paper, the authors will present a succinct review of design and procurement process. But, the practical aspects of the construction and installation methodology will be treated with more emphasis, more specifically the practice leading to good liner performance. Some of the poorly understood technical aspects of tubbing installation will be discussed more thoroughly and some currently accepted myths dispelled.

Aug 1, 2013

By S. Bastola, Y. P. Chugh

"This research determines shear strength and stiffness properties of bedding planes and joints in the roof strata rocks within 7.5 to 9 m (25-30 ft.) overlying the Illinois #6 coal seam (within the pressure arch zone). A shear test loading device was designed into a 1.334 kN (150 t) Forney Compression Loading Machine to perform direct shear tests in accordance with ASTM D5607-08 “Standard Test Method for Performing Laboratory Direct Shear Strength Tests of Rock Specimens under Constant Normal Force”. The data were used to determine peak and residual friction angles and the dilation angle. A total of 49 bedding plane samples were tested, out of which 46 (36 intact and 10 relatively weak and loose) samples passed QA/QC procedures in accordance to ASTM D5607. Samples from eight (8) different bedding planes- shale/limestone (SL), shale/sandstone (SSs), shale/bone (SB), laminated sandstone (LS), shale/shale (SS), bone/bone (BB), bone/limestone (BL), and limestone/limestone (LL) were tested. The number of samples tested for each bedding plane were: SL- 11, SSs- 8, SB- 5, BB- 4, LS- 6, SS- 9, BL- 1, and LL- 2. Peak and residual shear strength values at 2.75 MPa normal stress range 1.06 – 6.26 MPa and 0.82 MPa to 0.82 – 4.14 MPa, respectively. The average normal and shear stiffness values are about 11.98 GPa/m and 3.11 GPa/m. Dilation angles are low (<10?) and negative in some cases. Angle of sliding friction values range from 9? to 42?. Joint Roughness Coefficient (JRC) values were less than 10.INTRODUCTIONRock mass may be defined as the total in situ rock medium containing bedding planes, faults, joints, folds and other structural features. Therefore, it is discontinuous and may have heterogeneous and anisotropic engineering properties. Upon creation of an excavation in a rock mass, bedding planes and joints are the most likely points of failure initiation. The failure typically occurs either in tensile or shear mode. Upon failure initiation stresses are transferred to the neighboring rock mass and the failure progresses until stability is achieved through equilibrium of stresses and strength. An example of this mechanism is development of the pressure arch. This study determined the shear strength and stiffness properties in shear and compression of bedding planes and joints in the immediate roof strata rocks within 7.5-9 m ( 25-30 ft.) overlying the Illinois No. 6 coal seam (within the pressure arch zone). Since such data are currently not available for Illinois Coal Basin mines, researchers and engineers have been using estimated values for design purposes. The immediate roof lithology in the proposed mining area consists of shale 0.62 m; Bone 0.09 m (0.3 ft.); Limestone, 0.10 m (0.33 ft.); Shale 2.37 m (7.9 ft.); and sandstone 0.55 m (1.83 ft.). The bedding plane samples were provided by a mine in south-eastern Illinois operating at a depth of about 180 m (600 ft.)."

Jan 1, 2015

By Concentrator Staff

"IntroductionA brief literature search will reveal that the information available concerning rod mills and ball mills is quite extensive. This type of equipment is used to treat every element from antimony to zinc. The size and capacity of individual mills, the number of units employed, and the configuration of the equipment within a concentrator add another dimension to the possible scope of this discussion. It would be impossible to treat this volume of material with any degree of thoroughness.It is the intention in this paper to describe the simplest and generally the most typical circuit wherein a single rod mill and ball mill operate in parallel. Some of the subject matter will not be entirely applicable to every installation. However the principles should be generally relevant to most applications.Typical Circuit DescriptionFigure 1 illustrates the arrangement of the equipment associated with a rod-ball mill circuit.Ore is extracted from a fine ore storage bin (1) the capacity of which is large enough to allow .continuous mill operation independently of the mine and crushing plant production schedules. A number of feeders (2) may be employed to control the flow of ore to one or more feeder conveyor belts (3). In larger tonnage operations several such conveyors are employed at least one of which will be equipped with a variable speed control to allow adjusting of the amount of feed reporting to the rod mill. A rod mill feed conveyor (4) accepts all of the ore from these feeder belts for ultimate transfer to the rod mill. This conveyor is normally equipped with a weightometer (5) to monitor the flow rate of ore to the rod mill and ultimately to allow control of this flow. Typically these conveyor belts would be equipped with feed deficiency switches which would give a remote alarm of the fact that no ore is present on the conveyor. The conveyor belts are protected by underspeed monitors which will provide a remote alarm and automatic shutdown of the conveyor in the C'.'~nt that belt slippage occurs. Finally the belts are protected by monitors which will alarm and shut down a belt if it is not running straight in the idlers."

Jan 1, 1989

By D. Beneteau, L. Feldman, D. Milne, A. Hyett, G. Snell

"Behaviour of rebar bolts subjected to combined shear and bending in underground potash mining applications is not well understood. An experimental investigation compared load applied to resin-grouted No. 25 metric rebar to theoretical load, calculated using elastic bending theory. Distributed optical sensing (fibre optic) technology allowed axial strain measurements at 1.25 mm increments along the length of rebar. Experimental procedure, data processing methods, and equipment improvements are needed for field applications of optical sensing technology. Goals were to adopt procedures for instrumenting rebar bolts, conduct tests, and develop data interpretation methods to measure field deformations and loads. ¦ KEYWORDS Fibre optic, Potash mine, Rebar bolts, Transverse load testing RÉSUMÉ On appréhende encore mal le comportement des boulons d’ancrage pour barres d’armature soumis au cisaillement et au cintrage pour un usage dans des mines de potasse souterraines. Une étude expérimentale compare la charge appliquée aux barres d’armature de diamètre n° 25 (25 mm en mesure métrique) enduites de résine époxy à la charge théorique, calculée à l’aide de la théorie de la flexion élastique. La technologie de détection optique distribuée (fibre optique) a permis d’effectuer des mesures de la contrainte axiale à des différentielles de 1,25 mm sur toute la longueur de la barre d’armature. Pour des applications sur le terrain de la technologie de détection optique, il faut envisager une procédure expérimentale, des méthodes de traitement de données et une amélioration de l’équipement. Les objectifs établis consistent à adopter des procédures d’instrumentation des boulons d’ancrage pour barres d’armature, à effectuer des essais et à mettre au point des méthodes d’interprétation des données pour mesurer les déformations et les charges sur le site. ¦ MOTS CLÉS boulons d’ancrage pour barres d’armature, essai par charge transversale, fibre optique, mine de potasseINTRODUCTION Resin grouted rebar bolts are commonly used in potash mines in the province of Saskatchewan, Canada, in areas where shear deformation is observed in the rock, or where potentially unstable ground is present, including locations such as clay seams. Opportunities to observe deformations of rebar, as shown in Figure 1, are rare because it is unusual in underground potash mining to excavate supported ground. In this situation, a block of potash containing a rebar bolt had failed."

Jan 1, 2019

By P. Ashtari

Influence of Sr and Mn single and combined additions on the modification of the Fe-containing intermetallic compounds and mechanical properties of Fe-rich AA319 aluminum alloys have been investigated, The microstructural features e,g, morphology of the Fe compounds and eutectic Si has been correlated to the mechanical properties, It was demonstrated that modification of the Fe compounds from the platelet ß-Al5FeSi to the Chinese script a-Al8Fe2Si compound improves the UTS and elongation of the alloys by 10.3% and 83.9%, respectively. Moreover, the simultaneous modification of the Fe compounds and eutectic Si increases the UTS and elongation of the alloys by 15,3% and 116,1%, respectively.

Jan 1, 2005

By Veronique Falmagne

"In 1987 the only knowledge available of the Ansil orebody was that it was high grade, deep and relatively small . High stresses were also anticipated because there had been rockbursts during shaft sinking and destress blasting had been necessary (Fig. 1). From the design, through the development and now in the mining stage, rock mechanics and microseismic monitoring have been used to maximize recovery and safety and minimize dilution. Examples are given of the use of a microseismic monitoring system in the early stages o f mining. This paper also presents a review of the mine&apos;s in situ stress measurement campaign, cable bolting practice and backfill procedure.The Design PhaseAfter the initial mapping and classification work, preIiminary numerical modelling was performed using assumed stresses of ov = oH and oH = 3ov• The empirical Mathew&apos;s analysis was then used to optimize stope dimensions based on geomechanics data available at the time (Bawden et 01., 1988; Falmagne, 1987; Potvin et 01., 1988). Because of high stresses predicted by numerical modelling and a brittle, strong and relatively unfractured host rock which was believed to be rockburst prone, it was decided to mine without temporary or permanent pillars. However, in order to satisfy production rates, the orebody had to be broken up into two horiwns separated by a triangular pillar (Fig. 2). The final mining sequence is shown in Figure 3.The Development PhaseAt this point, based on work accomplished to date, including mapping and observations from drifting and modelling, the following problems were identified: (1) flat backs in the hangingwall andesite were thought to be highly stressed; (2) flat backs in weak massive sulphide ore would also be subjected to high stress and be difficult to support; (3) the felsic dyke was noted as a "" stress raiser"" , because activity increased as drifts approached it; and (4) chlorite coating of joints in the hangingwall was thought to be an important factor in reducing their stability."

Jan 1, 1991

By \/eena Sahajwalla, Jonathan Dicker, Paul O'Kane, Cath Skidmore, James Dankwah, Magdalena Zaharia, Rita Khanna, David Knights, N Saha-Chaudhury, Somyote Kongkarat

Due to the inherent limitations of current methods of disposal of end of life polymeric materials, avenues are researched towards developing alternative, environmentally friendly and economic recycling processes. Different polymeric materials (i.e. rubber, high density polyethylene (HDPE) and polyethylene therephtalate (PET)), quite distinct in terms of chemical structure and composition, were considered in the present study as carbon resources in EAF steelmaking. Investigations were conducted in both laboratory and industrial scale steelmaking to assess the effectiveness of using these materials as carbon sources for slag foaming in EAF steelmaking. Slag foaming is important because it enhances furnace efficiency.

Jan 1, 2011

By D. A. Livingstone

Abstract Golden Manitou Mines, Limited, nine miles east of the town of Val d&apos;Or in northwestern Quebec, are presently milling, at the rate of 1,000 tons daily, a relatively complex 3.11-phide ore and producing, in decreasing order of value, zinc, silver, gold, lead, and copper. The products are a zinc concentrate, a silver-lead-copper concentrate, and a silver-gold precipitate from cyanidation. Although several independent pre-production metallurgical investigations into the treatment of the ore were carried out, current practice is different from any of the recommended methods and, while still leaving room for improvement, is considerably more effective than earlier performance. Flow-sheet developments from the commencement of operations in 1942 are dealt with briefly, showing the reasons for making numerous changes, the shortcomings of the various schemes tried, and, finally, covering data pertinent to present-day practice. From the recovery standpoint, silver has presented the greatest difficulty. The writer&apos;s association with the Company coincided with the start of production. Characteristics of the Ore The predominant metallic minerals present in the ore, in decreasing order of their abundance, are: pyrite, sphalerite, galena and chalcopyrite, with lesser amounts of argentiferous tennantite-tetrahedrite, arsenopyrite, covellite, bornite, and chalcocite. The sphalerite is mostly light in colour, sometimes colourless, and practically free from combined iron. Some of the sphalerite is very closely associated with minor amounts of pyrite, chalcopyrite, and galena. Pyrie is abundantly disseminated as medium to fine grains; more rarely it is massive and contains occasional grains of sphalerite, galena, and chalcopyrite.

Jan 1, 1952

By W. A. Gow, G. M. Ritcey, M. C. Campbell

"Uranium is a unique commodity. It is both a metal and a fuel, It has both commercial and military uses. It yields ""clean energy "" but presents environmental concerns. All of these factors have an impact on the commerce of uranium.Being a metal, uranium is extracted from ore like many other metallic minerals. As a fuel, it is subject to the vagaries of energy commodity market forces. The history of uranium in the first nuclear weapons has led to nation al governments carefully controlling production and sale of uranium. The spectre of radioactive contamination of the environment adds further to the public concern over the disposal of low-level radioactive wastes from uranium processing and use.There have been a number of excellent reviews on the commercial aspects of the uranium industry. In this discussion, these aspects will be briefly summarized to provide a general picture of the strengths of the Canadian uranium industry and the pressures to which it is being subjected currently. The principal thrust of this paper will be to outline Canada&apos;s resource strength and to identify some factors which will affect Canada&apos;s ability to continue holding a sizeable share of the world uranium market."

Jan 1, 1985

By James R. Hein, Jane Reid, Robert W. Embley, Se-Won Chang, Randolph A. Koski

"Abstract - This is the first reported occurrence of an active hydrothermal field in an oceanic fracture zone setting. The hydrothermal field occurs in a pull-apart basin within the Blanco Fracture Zone (BFZ), which has four distinct mineral deposit types: (1) barite mounds and chimneys, (2) barite stockwork breccia, (3) silica-barite beds, and (4) silica, barite, and Fe-Mn oxyhydroxide in sediments. All deposit types contain minor amounts of sulfides. In barite stockwork, silica-barite beds, and mineralized sediment, Ba, Pb, Ag, S, Au, Zn, Cu, Hg, Tl, As, Mo, Sb, U, Cd, and Cu are enriched relative to unmineralized rocks and sediments of the BFZ. Fe and Mn are not enriched in the barite stockwork or silica-barite beds, but along with P, Co, and Mg are enriched in the mineralized sediments. Silver contents in deposits of the hydrothermal field range up to 86 ppm, gold to 0.7 ppm, zinc to 3.2%, copper to 0.8%, and barium to 22%.Mineralization occurred by diffuse, low to intermediate temperature (mostly <250°C) discharge of hydrothermal fluids through pillow lavas and ponds of mixed volcaniclastic and biosiliceous sediments. Bacterial mats were mineralized by silica, barite, and minor Fe hydroxides, or less commonly, by Mn oxyhydroxides. Pervasive mineralization of bacterial mats resulted in formation of silica- barite beds. Silica precipitated from hydrothermal fluids by conductive cooling and mixing with seawater. Sulfate, U, and rare earth elements (REEs) in barite were derived from seawater, whereas the REE content of hydrothermal silica deposits and mineralized sediments is associated with the aluminosilicate detrital fraction. Fe-, Zn-, Cu-, Pb-, and Hg-sulfide minerals, Ba in barite, and Eu in all mineralized deposits were derived from hydrothermal fluids. Manganese oxides and associated elements (Co, Sb, Mo, W, Cl, and Cu) and Fe oxides and associated elements (Be, B, P, and Mo) precipitated as the result of mixing of hydrothermal fluids with seawater."

Jan 1, 1999

By W. T. Robson

ONE of the problems encountered in any mine is the effect of increasing pressure manifested by increasing depth. Although the depth at which excessive pressure assumes serious proportion, and the manner in which it appears in underground workings, are influenced by a variety of factors, nevertheless the difficulty is present in all mines and its gravity increases with increasing depth. In the Kirkland Lake camp, as far back as seven years ago, mining had proceeded to depths sufficient to result in the formation of pressure great enough to cause violent disruption of masses of rock. It is proposed in this paper to deal with the effect of pressure caused by mining as observed at Lake Shore Mines, and to describe some of the methods which have been adopted to counteract it. There are many contributing factors in a study of the problem, and results vary widely in individual mines and in different localities. One feature common to all, however, is that there is ground subsidence, evidenced either by a gradual settling accompanied by crushing and shearing of the ore and wall-rocks, or the disruption of the ground surrounding the periphery of an excavation may take place suddenly, attended by more or less violent shattering of the rocks. Such violent failure of a mass of rock has been designated by the term rock-burst. The history of rock-bursts extends over a great number of years. They have occurred in some form or other in practically ali places where mining operations, at all but very shallow depths, have been carried out. Since the theoretical aspects of the subject have been dealt &apos;with at great length by capable and experienced writers (1), the present paper will give only a brief résumé of the theories propounded by those engaged in deep mining operations in various parts of the world.

Jan 1, 1940

By Matthew A. Baumann

Tooth wear on mining shovels presents a challenge for productivity. A shovel with worn teeth suffers from increased digging forces, longer fill times, and an increased likelihood of lost or broken teeth and adapters. Efficient maintenance planning relies on knowledge of tooth decay rates and patterns. A fully automated wear monitoring system can record detailed logs of tooth wear, permitting G.E.T. personnel to optimize maintenance scheduling. Studies have demonstrated that planned tooth change-outs result in significantly reduced costs as compared to unplanned maintenance. A machine-vision-based tooth-wear monitoring method is introduced. A rugged camera is installed on the boom of cable shovels, or on the stick of hydraulic shovels. The images are processed using a photogrammetric algorithm to determine the individual tooth lengths. Tooth length data is collected at intervals during shovel operations, forming a profile of the current wear state, speed of decay, wear pattern, and expected lifespan of teeth. A case study in a South American mine on a Komatsu PC8000 hydraulic front shovel is presented. Tooth wear is tracked over a 6-day period and wear rate statistics are computed for 6 teeth. This validates the system and provides an example of how wear patterns can be recorded and analysed by an automatic system. Armed with this data, mine personnel can reduce the cost and lost time due to unplanned maintenance, and observe the effects of mine conditions and operator behaviour on tooth wear.

May 1, 2011

By Milton Fies

Introduction The first experiment in underground gasification of coal in the United States was conducted at Gorgas, Walker county, Alabama, under a co-operative arrangement between the U.S. Bureau of Mines and the Alabama Power Company, at the suggestion of the Power Company. The test was conducted on property of the Alabama Power Company, that owns some 19,000 acres of coal-bearing lands on which there is developed a highly mechanized mine producing some 2,500 cons of good quality steam coal per day. At the same locality ?there is a 200,000 kilowatt steam plant one of the largest in the southern portion of the United States. The Alabama Power Company owes much of its beginning in 1912 to British vision and courage. The original plans for building hydroelectric plants in Alabama, and for the construction of necessary transmission lines, were submitted to Sperling & Company, bankers of London, who agreed to underwrite certain bond issues, the proceeds of which would be used in launching the new Company on its programme. The set-up by which these funds from England were received was through an intermediary Canadian company, which the English investors desired. The Canadian company - Alabama Traction, Light and Power Company, Ltd. became owner of the securities of the Alabama Power Company and marketed its own securities through the banking house of Sperling & Company. Without assistance at this time the Alabama Power Company could not have gone ahead with its programme of expansion and the bringing together of the properties necessary for laying the foundation for a strong Company, fortified with ample power resources essential for future requirements and for dependable service to the public.

Jan 1, 1948

By J M. Fletcher

The responsibility and scope of the Industrial Engineering Department, as organized at the Jeffrey mine, has been broadened to include any study, project or report that could result in more effective use of men, materials and equipment. Although still emphasizing wage incentives and co t reduction, much more varied work is now done, consistent with the in-.creased complexity of industry. Additional activities now include production, maintenance and inventory control improved job evaluation, packaging, labour utilization studies, technical sales liaison, mining, milling and service department n1ethods, plant layout, and specialized project analysis. Additional techniques include the extensive use of work .sampling and standard data. A recent trend has been toward increased emphasis on industrial relations, both in introducing change to the men and in providing requested explanations to Union stewards and officers. These new responsibilities have resulted in the development of specialists in some rather narrow industrial engineering fields, as well as the necessity for industrial engineering assistance in supervisory and job training.

Jan 1, 1963

By Peter C. Jones

Owing to the inadequacy of the ore transport system at Cassiar in the late 1960&apos;s, a new facility was required. This paper traces the various alternatives considered and gives a description of the tram line as installed. The problems encountered, changes made and future modifications are discussed in detail, together with the effects these have on maintenance and operations.

Jan 1, 1978