Search Documents

By W. E. Kuhn

Introduction The work, of which some of the results are described in this paper, was started with the object of investigating the properties of certain binary alloys of titanium made from powders. Our main interest was in the possible use of such alloys in gas turbines. We were attracted to titanium, as have been others, by its high melting point (I,724° ± 11°C.), its low density (4.54), and the likelihood that, if a relatively wide use could be found for the metal, it might become available in commercial quantities at a fairly reasonable price. The readiness with which the metal reacts with hydrogen, oxygen, and nitrogen was recognized from the very beginning. At the same time there seemed a good chance that alloys could be produced which, because of the formation of protective films, would resist the attack of these and other corrosive agents. No specifications were drafted to cover the 'quality' of the titanium hydride powder which was used in our work and which was, to judge by the results of a few preliminary experiments, the most useful source of titanium then (1944) available in sufficient amount for our purpose. During the course of our work, the need for such specifications became very clear (see Sections 9 to 12 of this pa per). Even today, lack of knowledge regarding the effects on titanium of impurities, some of which may later be looked upon as essential elements in commercial alloys of titanium, and difficulties in manufacture, make the preparation of specifications for commercial titanium and titanium compounds a doubtful procedure. The papers presented at the 1948 Symposium on Titanium, sponsored by the U.S. Office of Naval Research lend colour to this view. At the time our work was commenced, one had to depend upon the manufacturer to supply what he considered to be his 'best' material. It may be some time before we can ask for more than this, the question as to what is his 'best' being left to the manufacturer to decide. However, in this connection the results of our study may be of some value and on that account we are constrained to publish them.

Jan 1, 1950

By W. P. Campbell

Introduction OWING to the necessity of curtailing the length of this paper, nothing like an exhaustive treatment of the subject will be attempted. Instead, merely a few aspects will be considered, viz., water trouble in wells, sampling of waters, analysis, methods of reporting analysis, and the comparison of a few typical waters. The waters discussed will not be confined to those occurring in areas where oil or gas has already been found, but will include samples from areas in which drilling is being carried on in the hope that oil or gas may be found, i.e., from unproved fields. The Water Problem The problem of dealing with water encountered in oil and gas producing areas has engaged the attention of petroleum engineers from the early days of the industry. Water was not always considered a menace to oil sands; indeed, a certain amount of it was considered beneficial in some areas, but if such exist today they are very exceptional. In some fields, the problem is more acute than in others, and at times has baffled all attempts to solve it satisfactorily. Wells have been brought-in with promise of good production, but after a brief period have 'gone to water'. Whether ?it has always been a case of poor engineering in the form of unsuccessful water shut-off of 'top' or 'bottom' water, or because 'edge' water was present and water and oil were in such close contact it was impossible to remove the one without the other, is hard to say.

Jan 1, 1929

By C. R. Edwards

"Equity Silver Mines Limited, Canada's largest silver mine, has designed, built and operated a leach plant to reduce the levels of antimony and arsenic in its silver-gold-copper flotation concentrate. The orebody contained deleterious antimony and arsenic minerals in such proportions that the economic long-term sales contracts necessary to obtain project financing could not be procured. Construction of the leach plant therefore allowed development of the mine to proceed. Although the plant took some time to reach design throughput and product specifications, due to the complex and unique nature of the operation, these goals were successfully met and surpassed. This paper describes the physical plant and/or process technology modifications made to mold the main processes-concentrate leaching and filtering, autoclaving and filtration of by-products, and crystallization of salt cake-into an effective, economic operation.IntroductionEquity Silver Mines Limited, a member of the Placer Development Group, owns and operates an open-pit silver mine and related facilities located 37 kilometres southeast of Houston in north-central British Columbia. The mine occupies a 44 I-hectare (1089 acre) site at an elevation of 1300 metres (4265 feet) on the Nechako Plateau. Producing a copper concentrate containing high values of silver and gold, it is the largest silver mine in Canada and one of the largest in the western world. Equity stresses open communications, positive motivation, and production with safety, and achieved the best mine safety record in western Canada in 1984."

Jan 1, 1985

By Max W. Ball

THE world's largest known oil deposit lies in northern Alberta. In fact, according to government estimates, the famous so-called 'tar sands' of the Athabaska region contain several times as much oil as all the other proved reserves of the world. S. C. Ells, of the Department of Mines and Resources, who has been the Dominion Government's authority on the oil sands since 1913, has estimated the minimum content of the deposits at 100 billion barrels(!). C. P. Bowie, of the U.S. Bureau of Mines, has published an estimate of 250 billion barrels(2). ?In comparison, the latest authoritative estimate of the proved oil-field reserves of the world is less than 35 billion barrels(3). Out of this tremendous total, perhaps 500 million barrels are commercially available at present-day costs and prices; the remainder must be considered a latent reserve to be used when development costs are materially lower and petroleum prices materially higher than they now are. Mean-while, the 500-million-barrel portion presently available contains more oil than has been found in all the rest of Canada, and constitutes one of Canada's great mineral resources. Although these deposits have been known to white men since 1788, when Peter Pond, the explorer, found the Indians stewing the oil out of the sand and mixing it with spruce pitch to caulk their canoes, they are only now coming into commercial production. The purpose of the present paper is to describe the deposits, their oil content, their present development, and the possibilities that seem to lie immediately ahead. For the sake of completeness and clarity, the writer has not hesitated to use or to paraphrase material that he has previously published elsewhere in discussing various aspects of the oil sands.

Jan 1, 1941

By J. G. Ross

IN the paper entitled Block Caving at the King Mine (1), which was presented at the Annual General Meeting held in April, 1934, at Quebec, it was pointed out that, owing to certain conditions and financial restrictions, it was advisable to provide a temporary shaft. This was raised from the )00-ft. level to the bottom of the pit, and a 45-degree incline track was constructed up the face of the pit to surface. The temporary shaft and incline were within the ore-body, but were to be used only until such time as the new shaft-the subject of this paper-could be sunk and made ready for operation. After a careful study had been made of all available information pertaining to the ore-body, including examination of diamond-drill core records and geological data, a shaft location was selected well outside the ore-body. Further, since the crusher and dryer buildings are located over part of the ore-body, it was necessary to plan the removal of these buildings and to construct a new crushing and drying plant. This, and the new shaft, must operate in conjunction with the present mill and rock storage bin, which would continue robe used as formerly. No part of this programme, with the exception of drifting toward the shaft site, was started prior to 1937. More than usual detail on technical features is given in this paper in the hope that some parts of it may be of assistance to other members of the Institute who have to undertake somewhat similar work. The engineering and operating staff designed and supervised the work, while at the same time carrying on regular production in four mines at the rate of 12,000 tons of rock mined per day, the output at the King mine being at the rate of 140 tons per hour. No additional engineers were required.

Jan 1, 1939

By P. R. A. Andrews

"Graphite is one of the most versatile of non-metallic minerals because of its diversified properties, for example: it is unctuous; it marks readily; burns slowly; is almost chemically inert; is flexible over a large temperature range; is a good conductor of heat and electricity; is hydrophobic; has a negative temperature coefficient of resistivity; has excellent weathering properties; tends to emulsify with water-in-oil; is readily soluble in iron; and after oxidative treatment, can exfoliate like vermiculite. These properties give rise to its major uses in lubrication, refractories, marking instruments, electrical products and paints.Flake graphite is the variety which commonly occurs in Canada; the provinces of Ontario and Quebec contain the deposits of economic significance, although graphite occurs in other provinces. The beneficiation of graphite has been the subject of many investigations at CANMET, thus reflecting graphite 's importance as an industrial mineral. Thirty-eight studies relating to various aspects of beneficiation were conducted between 1918and 1989anda review of some of the more important studies is presented. The information includes mineralogy, beneficiation methods and results; flotation parameters and reagent concentration data are presented in tabular form. By so arranging the principal data, the research worker and production metallurgist will be assisted in the evaluation of graphite ores from a variety of origins."

Jan 1, 1992

By L. H. Van Loon

INTRODUCTION THE property of Madsen Red Lake Gold Mines, Limited lies between Russet and Faulkenham lakes in Baird and Heyson townships, district of Patricia, Ontario. It is about six miles south west of the town of Red Lake, with which it is connected by an all-weather road. All orebodies found to date at the property are silicified lenticular bodies which lie within tuff beds. The ore bas a specific gravity of 2.95. It consists of mica and chlorite schist, silicified and containing a considerable amount of disseminated carbonate, and mineralized with pyrite, pyrrhotite, magnetite, arsenopyrite, and chalcopyrite. Of these, pyrite, in coarse to fine disseminated grains, is by far the most abundant. Pyrrhotite occurs in ?the gangue material as medium to fine disseminated grains. A very small amount of arsenopyrite, in small crystals, is associated with the pyrite, and small grains of chalcopyrite occur in both gangue and pyrite. Although some of the gold present in the ore is quite coarse, a good deal of it is extremely fine.

Jan 1, 1951

By Luc Harnois, Gabriel Voicu, Marc Bardoux, Robert Crépeau

"Abstract-Detailed petrographical and geochemical studies have been carried out on the igneous and sedimentary rocks in the Omai area, part of the Paleoproterozoic Barama-Mazaruni greenstone belt, Guyana. The stratigraphic succession at Omai begins with basalts, associated with mafic-ultramafic intrusives and poorly-sorted conglomerates; these are overlain by andesites and quartzfeldspar porphyries, with pelites and tuffaceous sediments at the top. The volcanic-sedimentary succession was intruded by a quartz-monzodioritic stock (Omai stock) and granophyric rhyolite dikes. Several generations of mafic dikes were intruded discontinuously from the Mesoproterozoic to the Permo-Triassic. Volcanic rocks range in composition from subalkaline basalt to high-silica rhyolites, with a gap between 60% to 70% SiO2, which suggests the suite is bimodal. Major, trace, and rare earth element criteria were used to subdivide the rocks into tholeiitic and calc-alkaline types. The tholeiitic rocks are characterized by flat to moderately sloping chondrite-normalized REE patterns. On the basis of immobile trace-element ratios, the tholeiitic mafic rocks from Omai have characteristics of immature intra-oceanic island arcs, or of E-MORB basalts affected by a strong arc signature, as is commonly reported for back-arc basin basalts. The andesites, quartz-feldspar porphyries, rhyolites and quartz monzodioritic stock are calc-alkaline, with strongly sloping REE patterns, enrichments in the large-ion lithophile elements, and depletions in the heavy REE and high-field-strength elements, features which are typical of more mature island-arc settings.At Omai, two types of gold-bearing veins can be distinguished: vein sets (± stockworks) and tension veins, both post-dating the regional metamorphic peak at the level they were emplaced. The relationship between the gold mineralization and its host lithologies does not seem to be genetic. Rather, the emplacement of mineralization was strongly influenced by the rheological contrasts between the intrusive/subvolcanic bodies and the volcanic/sedimentary country rocks. These contrasts helped to focus the regional stress upon the more competent intrusive subvolcanic bodies, resulting in brittle fracturing, and therefore in greatly enhanced permeability to hydrothermal fluids. The Omai gold mineralization can be classified as late tectonic, with its emplacement controlled by the last brittle to brittle-ductile stages of the Trans-Amazonian orogeny."

Jan 1, 1997

By Gabriel Voicu, Harnois Luc, Marc Bardoux, Robert Crépeau

"Detailed petrographical and geochemical studies have been carried out on the igneous and sedimentary rocks in the Omai area, part of the Paleoproterozoic Barama-Mazaruni greenstonebelt, Guyana. The stratigraphic succession at Omai begins with basalts, associated with ma?c-ultrama?c intrusives and poorly-sorted conglomerates; these are overlain by andesites and quartz-feldspar porphyries, with pelites and tuffaceous sediments at the top. The volcanic-sedimentary succession was intruded by a quartz-monzodioritic stock (Omai stock) and granophyric rhyolitedikes. Several generations of ma?c dikes were intruded discontinuously from the Mesoproterozoicto the Permo-Triassic. Volcanic rocks range in composition from subalkaline basalt to high-silicarhyolites, with a gap between 60% to 70% SiO2, which suggests the suite is bimodal. Major, trace, and rare earth element criteria were used to subdivide the rocks into tholeiitic and calc-alkaline types. The tholeiitic rocks are characterized by ?at to moderately sloping chondrite-normalized REE patterns. On the basis of immobile trace-element ratios, the tholeiitic ma?c rocks from Omai have characteristics of immature intra-oceanic island arcs, or of E-MORB basalts affected by a strong arcsignature, as is commonly reported for back-arc basin basalts. The andesites, quartz-feldspar porphyries, rhyolites and quartz monzodioritic stock are calc-alkaline, with strongly sloping REE pat-terns, enrichments in the large-ion lithophile elements, and depletions in the heavy REE and high-?eld-strength elements, features which are typical of more mature island-arc settings.At Omai, two types of gold-bearing veins can be distinguished: vein sets (± stockworks) and tension veins, both post-dating the regional metamorphic peak at the level they were emplaced. The relationship between the gold mineralization and its host lithologies does not seem to be genetic. Rather, the emplacement of mineralization was strongly in?uenced by the rheological contrasts between the intrusive/subvolcanic bodies and the volcanic/sedimentary country rocks. These con-trasts helped to focus the regional stress upon the more competent intrusive subvolcanic bodies,resulting in brittle fracturing, and therefore in greatly enhanced permeability to hydrothermal ?uids.The Omai gold mineralization can be classi?ed as late tectonic, with its emplacement controlled by the last brittle to brittle-ductile stages of the Trans-Amazonian orogeny."

Jan 1, 1997

By J. J. Emery

There is an increasing awareness on an international level of the potential for utilizing many wastes and by-products as construction materials. This has resulted in recent major reviews by OECD and RILEM to supplement national activities by agencies such as CANMET, USBM, BRE and LCPC. Much of this international and national work was reported during an International Conference on the use of by-products and wastes in civil engineering held in November 1978 in Paris. Based on participation in the OECD and RILEM reviews, and the Paris conference, developments in waste and byproduct utilization of particular concern to Canada are described. The major technical and economic constraints involved are also reviewed, so that the over-all evaluation reflects important factors such as inherent variability and transport logistics. Areas requiring further research and development are also identified. Particular emphasis is placed on slags, salvaged asphaltic concrete and surplus sulphur. "Due to the rapid development of China's industry, more than a hundred million tons of industrial wastes are generated annually, which occupy lots of land for storing, bring about environmental pollution, obstruct industrial and agricultural production and cause harm to people 's living. Therefore we must utilize them effectively to create wealth for our country. "

Jan 1, 1979

By U. Erb, L. Monaco

"Electrodeposited nanomaterials are increasingly implemented in advanced industrial applications in the aerospace, automotive, defence, electronic and energy sectors due to their outstanding physical, chemical and mechanical properties, including increased strength and wear resistance, and superb magnetic properties. As with the development of any class of new materials, the corrosion behaviour of these electrodeposits requires considerable attention. This presentation reviews major developments in the understanding of the corrosion behaviour of nanocrystalline metals, alloys and metal-matrix composites over the last 20 years, with emphasis on how their intrinsically high density of intercrystalline defects does not compromise their corrosion resistance as initially expected.INTRODUCTIONOver the past 20 years there have been considerable advances in the understanding of the corrosion behaviour of nanocrystalline metals, alloys and metal-matrix composites. In this paper, the corrosion properties of nanocrystalline nickel, cobalt, zinc, and copper and some of their alloys are reviewed with emphasis on how a reduction in grain size affects their corrosion behaviour in different environments.It is possible to synthesize nanocrystalline material with microstructural refinement down to the range of 1 to 100 nm using a large number of processing methods. There are five basic synthesis methods that can be used to classify the different techniques: vapor-phase processing, liquid-phase processing, solid-phase processing, chemical synthesis, and electrochemical synthesis. Depending on the synthesis method, different microstructures (equiaxed, textured), shapes, and forms (films, particles, bulk material) may be produced. In addition, other factors may be introduced (eg. residual porosity or amorphous phases), aside from microstructural refinement, which can contribute to the observed properties (Erb, 2010). In order to interpret and categorize the resulting microstructures, a dimensional structure modulation scheme was introduced by Siegel (1996) in which zero-dimensional nanomaterials refer to individual particles, clusters, etc. One-dimensionality results from a layered (less than 100 nm thick) structure. Two-dimensional nanomaterials are thin, layered structures containing grains (less than 100 nm) within each layer. Finally, three-dimensional nanomaterials are bulk structures with an average grain size less than 100 nm."

Jan 1, 2012

By W. G. Q. Johnston, J. S. Fox

"A semi-continuous belt of Aphebian magnesian extrusive and related sub volcanic rocks has been delineated by the authors over a distance of 150 kilometres in the central La Ronge lithostructural domain in Saskatchewan. They range in composition from peridotite to basalt and attain true thicknesses of up to 800 metres. For the most part, they are confined to a basal position in the La Ronge/Wasekwan metavolcanic sequence, and appear to have been extruded onto sialic crust. However, at Lynn Lake, Manitoba, in the eastern continuation of the domain, similar rocks seem to be found only at a relatively high stratigraphic level.Although metamorphism seems to have obliterated any quench textures that may have existed in these rocks, ultramafic pyroclastics, pillows and amygdules as well as intercalated, fine-grained clastic sediment attest to the volcanic nature of these rocks. Bulk chemical analyses indicate that these rocks are heterogeneous, with komatiites, tholeiitic picrites and even rocks with some of the characteristics of boninite all being present. The close temporal and spatial relationship of ""boninites"" and komatiites in the belt may suggest a high degree of Aphebian mantle inhomogeneity in the domain.Nickel-copper mineralization has been found in differentiated tholeiitic stocks within the La Range domain (e.g., at Lynn Lake), but none has yet been found in the ultramafic volcanics. However, the tholeiitic picrites do host one economic gold deposit - the Agassiz Mine at Lynn Lake .Because of the depleted nature of their mantle source, the ""boninites"" of the domain are not considered to be likely hosts for mantle-derived nickel sulphide mineralization. However, the opposite is true of the komatiites, and this points to the need for whole-rock geochemistry in setting priorities for nickel exploration in the belt. In contrast, all of the magnesian rocks of the domain probably have the same gold potential. Inasmuch as the geophysical response to gold mineralization in the domain is likely to be unpredictable, lake-sediment geochemistry, followed by base-of-till and/or alteration oriented lithogeochemistry, should be emphasized during gold exploration."

Jan 1, 1981

By D. S. Salonine

Aluminum alloys are widely used in modern industry. Tubes and hollow shapes give great opportunities for structural purposes as well as fluid transport due to their stiffness and lightness, Extrusions on a mandrel or through a bridge die, that requires splitting of the billet with re-welding, produce hollow shapes with varied contours, fins and multiple cavities. Moving and stationary mandrels, mandrel lubrication, tooling for ribbed-tube heat exchangers, and for drilling pipes are considered. Bridge dies can be classified by the bridge position relative to the die face, by mandrel support structure, and by assembly type, The main parameters influencing the quality of the die-welded seams are considered, The difficulties of extruding various alloys through bridge dies are discussed in terms of metallurgical factors, Some approaches to the calculation of the stresses in a bridge are presented.

Jan 1, 2005

By Alan M. Jessop

This paper discusses the distribution of frozen ground in the zone of discontinuous permafrost in relation to the pattern of surface temperature. The importance of understanding permafrost in relation to surface construction and open-pit mining operations is stressed.

Jan 1, 1972

By N. R. Thote, J. L. Porathur, C. P. Verma

Highwall mining is a highly mechanized coal mining method associated with several advantages, such as a very high production rate (approximately 3,000 t/d) and low production costs. There is no requirement for underground support, ventilation, or blasting. Production leads to added recovery, which is otherwise lost in the ultimate pit. The use of highwall mining can bridge the gap that exists between supply and demand in the energy sector. This paper presents a brief review of highwall mining technology, including current status, analysis tools, and design techniques. In addition, it identifies important parameters from the analysis of failure case studies.

Jan 1, 2014

The primary steel industry of the Prairie Provinces consists essentially of three companies whose total annual melting capacity, as of January 1, 1963, was 333,000 net tons. These companies have steel rolling facilities. In addition, there are five other companies producing steel castings by melting scrap in electric furnaces which, with the plants having rolling facilities, gives a total annual furnace melting capacity of 380,000 tons. Since 1954, the annual production of steel ingots and castings has ranged from a low of 66,588 tons, in 1954, to a high of 211,138 tons in 1961. The present facilities on the Prairies for making steel ingots from scrap, and rolling them to produce light merchant mill products, appear to be sufficient for many years ahead. Steel scrap, as electric furnace feed to make steel ingots for the present line of products, will probably continue to be available at reasonable prices either on the Prairies or from the north-central United States. It is recognized, however, that residual elements in scrap may be-come of greater significance and necessitate more rigid control of scrap quality.

Jan 1, 1963

By Paul J. Bourassa

Alin de pourvoir aux besoins d'hébergement des quel¬ques 1600 employes qui travailleront dans toutes les spheres opérationnelles de l'exploitation du gisement du Mont-Wright, ainsi que de leurs families, Quebec Cartier a dû, avec l'aide de conseillers reconnus, et /a participation de ses employes résidant a Gagnon, étudier tour les nouveaux établissements résidentiels nordiques des dernières années tout au Canada qui dans lee pays scandinaves afin d'être en position de coneepter une agglomeration moderne répondant a toes les besoins de see future résidants. Les pre¬miers residants ont pu passer Noel 1972, et maintenant les logements prévus et construits sont °coupes a 92%.

Jan 1, 1977

By C. M. Bartley

Fluorspar, in addition to its familiar uses as a metallurgical flux and as a source of the electrolyte for aluminum production, has become important as an essential raw material in the rapidly growing fluorine chemical industry. The unique ability of fluorine to react and form compounds with al-most all other chemicals has made it one of the important elements in modern chemistry. Research and development over the past thirty years have resulted in a current annual production of fluorine chemicals that is both technically and economically important to industry. Because many of these chemicals and products are relatively new, and most have properties that are not duplicated by other materials, the present uses are expanding rapidly and new applications are being reported continually. Fluorspar, the only immediate and practical source of fluorine, is therefore an important mineral. This fact has been recognized in major industrial areas such as the United States and Western Europe, but has received little attention in Canada.

Jan 1, 1962

By Henri-Louis Jacob et Marc Bélanger

La province de Québec est un important producteur de roches et de minéraux industriels. En 1998, la valeur de cette production se chiffrait à 1,26 milliard de dollars canadiens (données préliminaires). Les minéraux industriels produits comprenaient: l'amiante extraite des gisements de chrysotile associés aux complexes ophiolitiques de Thetford Mines et d'Asbestos; l'ilménite et les scories enrichies en titane produites à partir du gisement d'ilménite massive du lac Tio associé au complexe anorthositique du lac Allard; le talc produit dans la région de Thetford Mines, à partir des roches à talc-carbonates associées à des feuillets de serpentinite; le mica broyé produit à partir de l'intrusion de suzorite du lac Letondal; le graphite en paillettes extrait du gisement du Lac-des-Îles; la wollastonite extraite d'une zone de skarn dans un lambeau de roches métasédimentaires enclavé dans le massif d'anor-thosite du LacSaint- Jean; le sel extrait aux Îles-de-la-Madeleine d'un gîte associé aux évaporites du Croupe de Windsor. Les nombreuses carrières dans le sud du Québec produisent, en plus de la pierre concassée, diverses substances incluant la pierre dimensionnelle (granite surtout); le calcaire pour la chaux, le ciment ainsi que divers usages industriels; la silice extraite à partir de formations de grès ou de quartzite. Le Québec est aussi un important producteur de tourbe de sphaignes qui est extraite de vastes tourbières qui se sont formées un peu partout dans le sud du Québec à la suite de la dernière glaciation. Les autres ressources en minéraux industriels comprennent des gîtes déjà exploités de brucite, de chromite, de magnésite dolomitique et de feldspaths ainsi que des gîtes de magnésite, de barytine et d'apatite faisant présentement l'objet d'évaluation.

Jan 1, 2001

By O. G. Olvera

"Refractory sulfidic ores consist of materials in which gold occurs finely disseminated within metallic sulfides or forming solid solutions, with pyrite and arsenopyrite being the two sulfides most commonly associated with gold. Typical cyanide operations show poor performance and require oxidative pretreatments to increase gold recovery. Pretreatment alternatives include roasting, pre-aeration, acidic and alkaline high pressure oxidation, and bacterial oxidation. The presence of arsenic, however, introduces a serious disadvantage to the use of roasting and bacterial leaching, while high pressure oxidation involves high capital costs. This work focuses on evaluating the effect of the addition of a carbon resin as a sulfur collector on the oxidation of different arsenopyrite concentrates under atmospheric tank leaching (ATL) conditions. The addition of the resin improved the oxidation of sulfides and favored the formation of elemental sulfur over the generation of sulfate. The use of AF5 in ATL resulted in higher gold recoveries under standard cyanide carbon-in-leach and thiosulfate leaching.INTRODUCTION Refractory sulfidic ores consist of materials in which gold occurs finely disseminated within metallic sulfides or forming solid solutions, with pyrite and arsenopyrite being the two sulfides most commonly associated with gold. Gold is not readily accessible to solutions in these types of ores and typical cyanide operations show poor performance, thus making the use of oxidative pretreatments a requirement to increase gold recovery. Pretreatment alternatives include roasting, pre-aeration, acidic and alkaline high pressure oxidation, and bacterial oxidation. The presence of arsenic, however, introduces a serious disadvantage to the use of roasting and bacterial leaching, while high pressure oxidation involves high capital costs. The use of carbonaceous materials to enhance the dissolution of sulfides is not novel, and leaching additives such as coal, activated carbon and carbon powder have been considered for the improvement of bioleaching, atmospheric leaching, and pressure oxidation leaching processes. However, this type of technology has been focused mainly on the recovery of copper from copper concentrates containing chalcopyrite with less attention paid to other sulfides."

Jan 1, 2017