Search Documents

By Sibson RH

The gold province of Otago occupies an area of upwarped basement, the Otago Schist, comprising predominantly quartzofeldspathic and volcanogenic metasediments. This assemblage is the product of collisional tectonic deformation and associated metamorphism, mainly to lower greenschist facies, during the Rangitata Orogeny (200-100 Ma). Historically this region has produced 240 tonnes of gold, 4% (10 t.) of which was from the mining of Cretaceous gold- quartz mineralised vein systems. Auriferous vein systems in the Otago Schist are mainly hosted within NW trending normal fault-fracture arrays, however NW trending reverse fault-hosted vein systems also occur. We propose that the Late Cretaceous-mid Tertiary Otago Schist structure represents a regional anticlinorium containing flexural folds of at least two wavelengths. The anticlinorium structure has been quantified by determining variations in angular discordance between schistosity and the Otago Peneplain, a Late Cretaceous-mid Tertiary erosion surface covering most of the Otago district. A structural model for the evolution of the post-collisional anticlinorium requires the cooling surficial zone (carapace) of a retrograding metamorphic belt to behave as an elastic lid. Erosion of topographic load on the carapace drove isostatic uplift, which was greatest in the tectonically thickened core of the orogen. In this way differential uplift produced flexural deformation in the elastic carapace, expressed as a large scale arching of the orogenic belt. Flexure created tangential longitudinal strains in the outer-arc, leading to extension and the formation of mineralised normal faults. These structures are separated by a neutral surface from shortening and associated mineralised reverse faults in the inner-arc. Our structural model predicts that the distribution of auriferous lodes should be localised about zones of maximum flexural curvature, where the tangential longitudinal strains are highest. As a result, NW-SE hinge regions separating schistosity dip domains in the Otago gold province may have new found significance as potential exploration targets.

Jan 1, 1995

By D L. Richardson, B Tiedt, C D. Morgan

Following residentsÆ concerns that the ongoing operations of Collinsville Coal (CCP) mine may be resulting in the release of contaminants, including products of acid mine drainage (AMD), into downstream environments, the Queensland Environmental Protection Agency (QEPA) issued CCP with a Notice to Conduct or Commission an Environmental Evaluation at Three Mile Creek. A key objective of the Environmental Evaluation was to assess the extent and magnitude of impacts to aquatic communities and their habitats. A multidisciplinary investigation examined a suite of physical, chemical and biological indicators to meet this objective. The study also aimed to identify contaminants of concern and the location of potential pollutant sources. Potential indicators of AMD, including elevated dissolved solids concentrations and low pH, were evident within the mine lease. However, significant differences in concentration of these indicators upstream and downstream of the confluence with Three Mile Creek were not observed. Although only proxy indicators of AMD contamination, these results suggest that the extent of impacts downstream is minimal. For the purpose of this study, physio-chemical indicators were selected on the basis of those best likely to provide an understanding of the likelihood of contamination, within the constraints of readily available long-term monitoring data. Ecosystem health indicators were adopted to supplement the existing data set and provide a more æroundedÆ perspective of water quality attributes within the system, generally unattainable by standard physio-chemical assessments. In contrast to AMD products, sediments were considered more likely to have a widespread impact on aquatic ecosystems. Waterways throughout the study region, including those unaffected by mining, have been affected by broad-scale sedimentation and were typically highly turbid. Due to the many diffuse sources of sediment potentially liberated within the catchment, the contribution of the mine compared to other land uses on total sediment loads entering streams is difficult to determine. This is clearly a major management issue for mines throughout the Bowen Basin. Streams of the central Queensland region display enormous variability in water flows and physio-chemical characteristics over a range of spatial and temporal scales. This variability presents major difficulties in distinguishing anthropogenic impacts from natural variability (noise). Despite this variability, impact monitoring by mines in the central Queensland district has tended to focus almost entirely upon physio-chemical indicators. The results of the present study indicate that a multiple indicator approach to environmental assessment is more useful for separating mine related impacts from natural ænoiseÆ and impacts from other land uses. In the absence of such information, by adopting the precautionary principle of Ecologically Sustainable Development (ESD), there is potential for an environmental impact to be incorrectly attributed to mining when other activities in the catchment may be contributing to changes in stream æhealthÆ.

Jan 1, 2003

By Wang S

Fragmentation is the basic concern in rock blasting and serves as the main measure of blasting effectiveness. A good estimation of fragment size distribution before blasting is very useful and helpful for selecting the proper equipment for loading, transporting, and crushing rocks. A fragmentation model is presented that is based on a hole by hole analysis and correlates the rock properties, burden, spacing, and explosive column with the blasted volume and fragmentation obtained. The drill bench is divided into three separate areas corresponding to different breakage mechanisms. They are: 1) a main breakage or casting area, 2) a secondary breaking area, and 3) an overbreak area. The boundary of the main breakage area is found from the magnitudes of strains in the stress waves and the tensile strength of the rock. The secondary breaking area is determined by stress wave reflections at discontinuities and interactions between colliding stress waves from adjacent boreholes. The overbreak area is that beyond the main breakage area "where the reflected tensile waves no longer break the rock. This analysis is applied on a hole by hole basis to locate the breaking points. Then connecting the breaking points on each side of a borehole forms the triangle of the main breakage area. This is repeated for the next hole and the remaining area is the secondary breakage area. After the angle and area for each hole are found the Kuz-Ram model is used to predict the fragmentation size distribution for each hole. Then summing up the size distribution for each hole gives the total fragmentation distribution. This analysis has been successfully applied to field tests performed in a limestone bench where the entire spoil pile was screened to determine the fragment size distribution. Knowing the explosive and rock properties the breaking area was found for each hole, the strain and stress values, the breaking point, and angle of breakage (104 degrees). The fragmentation size distribution was then calculated and compared to the field data with excellent agreement.

Jan 1, 1990

By Vnenk L, Hargraves AJ

Metropolitan Colliery has some areas of roof where immedi- ate support is required in development. The disadvantages of percussive roof bolting at the face have led to recent produc- tion trials with rotary boring and rapid=setting resin anchored roof bolts developed at the Colliery. The three innovations involved are: (1) the wet drilling of small holes with an all- hydraulic, portable rotary boring machine; (2) the rapidity of loading a "point anchored" resin bolt; and (3) the consistently high anchorage strength available. All three innovations provide striking advantages over the previously available alternatives. The greatest disad- vantage - that of cost of resin - is not prohibitive, and there is promise of improvement in the future. There are possibilities of variations of the techniques for special support problems in particularly difficult roofs.

Jan 1, 1971

Using normal low pressure filtration methods for the dewatering of fine china clays, the best that can be achieved is cakes with about 30% moisture. In order to get the moisture levels down to acceptable levels the traditional method used is thermal drying, which is both costly and dust creating. It was to improve this process that ECC International embarked upon a programme of development of filtration equipment using high pressure to achieve significantly lower moisture levels. This development work investigated several design philosophies and culminated in the production of two quite different solutions. The High Pressure Plate Press uses round plates / chambers of one metre diameter and a filtration pressure of 70 bar. This press is fully automatic and produces a surface dry cake that has sufficient plasticity for the further processing that is required on specific qualities of china clay. The TUBE PRESS on the other hand uses a unique design configuration and operates at a filtration pressure of 100 or 140 bar, depending upon the model. The TUBE PRESS produces a brittle, surface dry cake that is easy to handle and a filtrate that is usually crystal clear. The TUBE PRESS achieves a much higher degree of separation than is possible with conventional equipment, which is particularly important if the filtrate is the product. Over the past 15 years plants incorporating both HP Plate Presses and TUBE PRESSES have been installed in the china clay operations of ECC International and are giving excellent trouble free service. The TUBE PRESS has also proved to be extremely versatile, effectively dewatering a wide range of fine particled slurries, in a number of diverse industries.

Jan 1, 1989

By Filigenzi M. T

Stresses around mine openings at depth can cause the surrounding rock to fail, releasing stored strain energy. When this happens, the rock may literally explode or `burst' into the opening without warning. As mining progresses deeper into the earth, the possibility of seismic events and rock bursts increases. Researchers at the US Bureau of Mines (USBM) are currently studying seismic activity in three underground hard-rock mines in the United States: the Homestake Mine, Lead, SD; the Lucky Friday Mine, Mullan, ID; and the Sunshine Mine, Kellogg, ID. Waveforms from seismic events are recorded by personal-computer-based hardware and software. This information is archived and transferred from the mine sites to the USBM via modem communication links. Then, using USBM-developed software, the events are analysed to determine various parameters, including magnitude, frequency, and location. In addition, researchers are modelling the deep levels of the Homestake Mine using a finite-element code. These models generate stress and displacement values for a given loading condition. By studying material properties, in situ stresses, and seismic activity along with actual scope sequencing, researchers can make correlations between stresses induced by mining and the frequency and magnitude of seismic events. Information on seismic events coupled with results from finite-element analyses have increased understanding of rock mass behavior and the mechanisms that may lead to rock bursts. Optimisation of slope sequencing designs as a result of these studies could reduce rock burst hazards.

Jan 1, 1995

Queensland hosts vast deposits of brown and black coal, significant accumulations ranging in age from Permian to early Tertiary. The great diversity of coal resources in the State to some extent reflects the proximity of Queensland to plate-marginal tectonic processes through much of the Phanerozoic eon. Coal is contained within sedimentary basin fills of four fundamental types; 1. extensional, 2. foreland, 3. strike-slip, and 4. intracratonic. Thick (10 m+) though laterally restricted coal bodies are characteristic of extensional and strike-slip basins, whereas coals of more modest thickness but much greater lateral extent are typical of foreland and intracratonic basins.

Jan 1, 1991

By Bicer N

Current problems in predicting sub-surface strata movement and fracture development due to longwall mining have highlighted the need for more accurate, dependable methods of physical modelling of rock mechanics problems which are beyond the capabilities of current mathematical techniques. Physical model studies of the caved zone above the working faces up to the base of a water source are of importance in attempting to understand changes in mass permeability due to induced fracture zones and the resulting ground water conditions. Turkey's most important supplies of coking coals are to be found within the hard coal resources of the Black Sea coast. Coal seams up to 9 metres thick, dipping at angles as steep as 90 degrees are being successfully mined at the Kozlu Mine. Since 1956, mining operations have been carried out under the sea in dry conditions. The undersea mining conditions of the Kozlu Mine have been investigated using scaled physical models constructed from artificial materials which satisfied necessary scaling requirements. Models representing the in-situ conditions were tested and the following extraction sequence was employed: 1. The Sulu Seam extraction 2. The Acilik Seam extraction (as two slices) 3. The Piric Seam extraction. The displacement of the fixed reference points were subsequently measured using a high precision photogrammetric technique and induced horizontal and vertical strains were calculated.

Jan 1, 1988

Before proceeding I wish to say that the excellent diagrams by which my paper is illustrated are the work of Mr. C. H. Barnes, Constructing Engineer of the Kalgurli Gold Mines Limited, and I am also much indebted to Mr. F. A. Moss, manager of the mine and for the privilege piIling information not previously made public.The limited time at my disposal has coolled to, curtail the scope of my paper to a few practices in ore treatment which are being worked on the Kalgurli Mine, but which I believe are of more than ordinary interest to thp~e Goncerned in modern treatment of gold ores. As an introduction to my subject it is, necessary that I should give a brief outline of the process by whiGh the gold is won from the complex sulpho-telluride ore of the Kalguili mine.My business is not to enter into any discussion as to the relative merits of the two rival sulpho-telluride ore treatment processes at work on the Kalgoorlie field, viz, the treatment of the unroasted ore after shining by solutions of bromocyanide, as against the treatment of the ore-after roasting by solutions of potassium or sodium cyanide either in filter presses or percolating sand vats. Even if reliable costs and percentages of extractions were obtainable in each case, it would not constitute an infallible basis of comparison, as the larger plants would necessarily have an advantage in cost per ton as against the small plants, and the other conditions obtaining are in many Cases dissimilar.

Jan 1, 1903

Exploration for economic nickel sulphide mineralisation has often been directed by rationalisations based on poorly understood genetic models. Among those that have enjoyed popularity over the past decade are the "layered gabbro" model and the "basal ultramafic" or Kambalda model. The new discoveries in the Mt Keith-Agnew area could well become a model for future nickel search. Exploration based on even the crudest state- ment of the Kambalda model - prospect the basal contact of Archaean ultramafic complexes for gossanous expressions of sulphide mineralisa- tion - has met with remarkable success. Refine- ments to this model, besides satisfying the geology of any particular deposit, have the major virtue that many of the genetic options - magmatic segregation, hydrothermal transport, sulphurisation, replacement sedimentary, structural control, etc. - are still open. Recent descriptions of highly magnesian silicate melts associated with the ultramafic rocks, do however, place some constraints on the formation of these deposits. Further evidence, from experimental studies on sulphide-silicate and sulphide-oxide phase relationships, and nickel-iron exchange in pyrrhotite, is taken with descriptions of sulphide nickel occurrences in Western Australia to examine genetic models for existing ore bodies.

Jan 1, 1972

By Li YQ, Yoon RH

The photoresponse of natural mineral pyrite and galena electrodes has been studied in aqueous solutions on freshly fractured surfaces (some fractured in situ) using moderate overvoltages. When fractured in situ, the electrode potential of both minerals instantly drops several tenths of a volt. Pyrite exhibits a spontaneous anodic photocurrent at fracture, which indicates upward band bending (depletion layer) on the n-type electrodes. The negative surface charge responsible for the depletion layer is believed to arise from a surface state that is intrinsic to pyrite surfaces, possibly modified by hydroxide ion adsorption. The flat band potential, Vty, of pyrite is at approximately -1.0 V (SCE) at pH 9.2 but to reach V(b, pyrite has to be cathodically decomposed. In contrast, galena assumes the flat band potential at fracture. Subsequent polarisation of galena at potentials positive of Vth produces an anodic photocurrent (upward band bending) and polarisation negative of Vro a cathodic photocurrent. Most of the galena electrodes studied were degenerate n-type and at potentials negative of Vtb, no cathodic photocurrents are observed, indicating the bands cannot be bent downward, consistent with the Fermi level at the surface merging with the conduction band edge near Vn,. Several were close to intrinsic, with the photocurrent changing sign near Vn,.

Jan 1, 1993

Integrated geological interpretation of aerial photographs and Landsat images revealed that the gold mineralisation at Kyauk Pahto took place in a narrow zone of tension fractures within part of a previously unrecognised dextral wrench fault system. The latter is the wider manifestation of the well known Sagaing (right-lateral) strike-slip fault which has a length of more than 1 000 km, and it demarcates the boundary between the Indo-Australian and Asian plates. A subtle, right-handed kink affects the full width of the Sagaing Wrench-fault System at about the latitude of Kyauk pahto, and the extra dilatancy imposed on the tension fracture zone facilitated episodic ingress of mineralising hydrothermal fluids by "seismic pumping".

Jan 1, 1987

By Corner NG

A sea bed sampling programme by CRA Exploration Pty. Limited over an area of 12000 km offshore from Westland, Southland and Otago, New Zealand, led to the discovery of the Harvester Prospect, an area of some 67 km2 which averaged 189 mg/m3 gold in surface samples. This area was in water depths of 70 to 100 m and contained a high grade core of 33 km2 which averaged 283 mghn3 gold. The gold recovered was fine grained, averaging 124 microns, and indicated a potential resource of approximately 10 t of gold per metre of thickness. Interpretation of existing seismic and geological data suggested that the gold anomaly may be associated with a unit of sediments 10-40 m thick, probably deposited during a lower sea level stand. Two initial attempts at vibrocoring the anomaly produced inconclusive results. In 1989 a much more powerful vibrocorer with scaled up support facilities and a dedicated 24 It turnaround laboratory were employed. The final results clearly showed that the gold was from an uneconomic surface enrichment.

Jan 1, 1990

By Mostyn G

In the last three decades various theories have been presented to allow the estimation of the force required to cut rock. These have generally relied on an hypothesised mechanism of chip formation.The paper presents results of an experimental program completed on an unjointed artificial rock in which the force and chip geometry were measured during deep cutting with a quarter scale bulldozer tyne. The program included various depths of cut and artificial rock of varying strength. The experimental results are compared with predictions based on three expressions for cutting force. Generally the measured forces are within the range of those predicted but none of the methods predicts the cutting force with any accuracy. It is considered that the discrepancies are due, in part, to the fact the that actual shape of the chip formed in deep cutting is quite different to that assumed in developing the theories and thus the theories cannot be expected to predict the cutting forces. It is concluded that Evans and Nishimatsu's theories predict lower bound estimates of the horizontal cutting forces. Deliac and Fairhurst's approach appears to over estimate the forces required to cut rock. New methods of prediction are required based on the observed mechanisms of failure.

Jan 1, 1993

By Miller J. D

The mechanism of adsorption of gold from alkaline cyanide solutions by carbon has been the subject of much research over the past decade. In this paper, the nature of the gold cyanide adsorption phenomenon is investigated, particularly with respect to carbon substrates and associated surface adsorp- tion sites.

Jan 1, 1991

By Flann R. C

A small modification to current industrial practice should lead to better nickel powders for use in alloying, electroplating, and powder metallurgy. Nickel powder compacts sold for alloying are not always suitable for electroplating applications, since some presently used commercial powders will expand on sintering. Further, such nickel powders are unsuitable for use in the production of powder metal parts, because of expansion during heating of the near-net-shape preforms. Research in these laboratories has enabled the elimination of expansion, and led to techniques for the production of compacts suitable, in particular, for commercial use in both alloying and electroplating. The techniques include: powder pretreatment, cold pressing and sintering, hot pressing, and hot pressing and sintering. In this way compacts are readily prepared with densities of at least 93 per cent of solid nickel, and these, when used as anodes in Watts general purpose and bright baths, give both cathode current and plating efficiencies of 90-98 per cent.

Jan 1, 1979

By Murphy MW, Klaric SD

The history, operation and design of the Secor continuous rod production process is described. The effective operation of the plant is influenced by accurate monitoring and control of molten metal properties, mould release application, coolant application and composition and correct setting of all operating parameters. The continuity of operations, which is an essential feature of this type of plant, is also greatly influenced by the service life of wear parts in the operation. This paper deals with three principal wear parts which come into direct contact with copper during operation, these are:

Jan 1, 1985

By Andrews JRG

Chrysotile asbestos is a valuable resource. Used as a reinforcement in asbestos cement, products are obtained which are cheap, are not attacked by vermin, do not rot or support growth of fungi and are unaffected by water or humid conditions. Such products are of great value in the developing countries where inexpensive and durable building materials and pressure pipe are very important to development, housing and water supplies. Concern over the adverse effects of inhaling asbestos has led to the introduction of increasingly stringent controls world wide on the quantities of airborne asbestos per- missible in the occupational situation. Wet processing has the potential for virtually eliminating the environmental concerns with asbestos dust both in fibre production and in the materials handling section of the manufac- ture of asbestos cement products. In addition, high efficiencies associated with wet process- ing mean that better yields are obtained and that the tailings which are dumped have a lower residual asbestos content. Since early 1977, ICI Australia and Woodsreef Mines have been engaged in a programme of research to develop and evaluate a wet mill- ingprocess to produce, from ore and existing tailings, high grade fibre suitable for use in asbestos cement products. The process has been developed through microscopic studies, labora- tory bench scale experiments, work in a small scale semi-continuous plant and product evalua- tion on experimental size Hatschek asbestos cement machines. A prototype mill with a normal feed rate of 1z tonnes per hour and capable of producing pipe grade asbestos from Woodsreef ore has been constructed and was operational from January, 1982 to July, 1983. A range of asbestos cement products have been made successfully on full scale Hatschek machines using fibre from ore and tailings milled in the prototype mill. Economic evaluations indicate that a wet process mill would be cheaper to build, operate and maintain than an equivalent dry process plant. A commercial plant has been designed 1. Manager New Process Development, Woodsreef Mines Limited, Barraba, Australia. 2. Senior Lecturer, Department of Chemical Engineering, Monash University, Vic, Australia. formerly Senior Research Officer, Research Department, ICI Australia Limited

Jan 1, 1986

This paper will describe the exploration project which led to the discovery of the La Escondida porphyry copper deposit in northern Chile and will serve as companion paper to the description of the geology of Escondida being presented by J M Ojeda. The author would like to express his appreciation to Robert Hickman, Chairman of Minera Escondida, for permission to present this paper.In July 1978, a proposal was made by J D Lowell to Robert Wheaton, then Exploration Manager of Utah International, that Utah fund a "grass roots" program exploring for porphyry copper deposits in northern Chile. Wheaton expressed interest, and it was agreed that Getty Oil Co also be invited to participate. A joint venture agreement for the Atacama Exploration Project was signed January 1, 1979, between Utah, Getty and Lowell. The project was managed by Lowell who reported to a management committee which through most of the project consisted of Lowell, Francisco Ortiz, Robert Wheaton, Maurice Young, Sigfried Muessig and Louis Rove. Oliver Warin and Jim Bratt participated in the committee in the last phase of the contract. Special thanks are due Louis Rove of Getty and Maurice Young of Utah who made contributions throughout the course of the project. Francisco Ortiz was resident manager through most of the project.

Jan 1, 1990

By Hilde TWC

Synthesis of GLORIA side-scan sonar and other geophysical data has provided morpholo- gical and tectonic details of the interaction between the Nazca and South American plates along the Peru Trench (80S-15¦S). Our analyses suggest that a new propagating rift of the Galapagos type is evolving along the Mendana Fracture Zone (MFZ). Subduction induced rift- ing of the Nazca plate is accompanied by organized seafloor spreading for the last 3 Ma at least. GLORIA sonographs and bathymetric mapping show an 8-10¦ divergence in MFZ width towards the Peru Trench. The fracture zone comprises numerous ridges and troughs and a lack of sediment cover in the axial part. Young magnetic lineations (anomalies 1-2A) are observed within the fracture zone wni.cn are orthogonal to the older Nazca plate lineations. The central anomaly narrows west- ward and can be observed up to 400 km seaward of the trench whereas anomaly 2A is terminated about 200 km from the trench axis. Recent SeaMARC II sonar mapping in the region shows large igneous blocks in the Trench axis to the north of MFZ but absent to the south. We believe these blocks represent young seafloor of MFZ rift/spreading center broken off from the ridges as they subduct along the Peru Trench. The MFZ rift is propagating west- ward at a rate of 115 km/Ma (25 km/Ma relative to the South American plate). Given the present rates of accretion at the East Pacific Rise and of propagation along MFZ rift, the Nazca plate will be divided into two parts in about 35 Ma.

Jan 1, 1987