Search Documents

By Frazer E. J, Lwin T

Measurements of coulombic efficiency (QE) for zinc electrodeposition were carried out under mass-transfer-controlled conditions using a rotating disc electrode in synthetic acidic zinc sulphate solutions. Various methods of solution preparation and purifi- cation were investigated using reagents vary- ing from analytical grade to high purity; the purest solution was obtained-by dissolving 99.9999% zinc (Koch-Light) in sulphuric acid solution (BDH Aristar). Improvements in sol- ution purity did not necessarily increase QE, especially where apparently beneficial impur- ities (e.g., Pb) were initially present. The maximum QE obtainable through variation of temperature (T), current density-(i) and elec- trode rotation rate was established using a statistical optimization technique. The QE was determined principally by T and i, with significant interaction between these factors in the highest purity solution. QE contours, which gave an overall view of solution per- formance, were constructed and predictions about the response under conditions similar to plant practice were made. Wark's Rule (the dependence of QE on zinc/acid ratio) was obeyed in the purest solution over the range of composition commonly encountered in zinc plants. High concentrations of Na2SO4 and K2SO4, which occur in some plant solutions, were found to increase QE marginally ("1.2%). The intrinsic effects of individual impurities such as Cu and Ni were evaluated by additions (up to 5 ppm) to the purest solution. Decreases in QE were found to be minimal at the impurity levels normally encountered in zinc plants.

Jan 1, 1987

Manganese ore has been mined from the Peak Hill Gold- field since 1948 and from the Pi'lbaraòGoldfield since 1954, and it is probable that some deposits- In and, near the Phillips River Goldfield will be mined at a future date', There are also several million tons of mariganiferous ;naterial which is too low in manganese. .co.ntent_ for . present requirements. The manganese deposits¦of Western Australia are mostly superficial. They hav' been formed during the Cainozoic Era by supergene enrichment ò6f Precambbrian: manganiferoius sediments, and by deposition from -solution on, or'in caves in, the Cain- ozoic land surface. The manganese in solution was derived from the weathering of Precambrian manganifer.ous s.edimexsts, None of the deposits are of hydrothermal origin, nor are they related to igneous rocks in any war, other than as ultimate source rocks. There is ho evidence-'t.o.:sugge,st that meta- morphism has been responsible for.the emplacement of any deposit. The tenor of the ore varies'aec'ording'to the quantity of gangue in the orebody and- also to the nature of the part- icular ore minerals. The main ore.mine.rals are the oxides pyrolusite and cryptomelane and the 'o'xide-silicate braunite. The main gangue minerals are hematite, limonite and quartz. The deposits of high grade oreò(-above.45 per cent Mn) range in size from 50 tons to many thousands of tons but most of them are in the 500-5,000-tons r .nge .

Jan 1, 1964

By A Suokas

Boliden Tara Mines Ltd, located in County Meath Ireland, produce in excess of 2.5 million tonnes per annum of ore from the underground resource located 40 miles north west of Dublin. The zinc-lead ore is mined using long hole open stoping techniques, with ore treated on site. The operation is continually searching for new ways to improve productivities at the mine, and have employed a detailed data acquisition and reporting system on site to provide feedback around performance. One area where both Boliden Tara Mines Ltd and Orica Mining Services believed improvements could be made was in the application of bulk emulsion technology through an Orica supplied but Tara operated Maxipump Delivery System for all production and development blasting at the mine. Both parties committed to the evaluation of this technology at the mine, however the capital cost and technical and economic changes meant the project needed to be diligently investigated and any improvements documented. The first stage of this project was for Orica Mining Services personnel to visit the operation, and conduct a detailed analysis of the operationÆs performance over the past 12 months. The next step in moving forward was then to commission and utilise the customer operated emulsion system at the mine. This was then followed with the collation and analysis of data from the demonstration period to examine and document the benefits of the system. This paper is a summary of the observations made during the site inspection and the data analysed to date, and has been used in determining operational and financial improvements in the comparison between a Maxipump Emulsion Service and the current ANFO loading systems.

Jan 1, 2005

By J Slade, R Trueman

Unplanned dilution has the potential to seriously undermine the economic viability of a mine, and in some cases results in mine closure. The effect of stress damage on dilution has become increasingly relevant as mining depths increase. In the case of narrow vein mining, the incremental extraction of long-hole rings has the potential to result in a moving high stressed zone at the stope brow. This leads the hanging wall and footwall to experience a spike in the stress to strength ratios as the brow passes. In some cases, the stress to strength ratio may be high enough to result in fracturing or damage to the rock mass. The aim of the study described in this paper was to investigate whether stress damage results in a significant increase in dilution. The study involved analysis of overbreak from 410 case studies from the Kundana Gold mine in Western Australia. Site personnel had already undertaken calibration studies of the stress levels that result in rock mass damage. This calibration, in conjunction with numerical modelling showed that stress damaged stope walls at this mine had on average 50 per cent more overbreak than stope walls where stresses had not exceeded the damage criterion. For a design mining width of 1.5 metres, and with both walls impacted, this represents 36 per cent increase in dilution. After adjustment for possible sources of bias the difference reduced to an average 0.10 metres per stope wall, representing 13 per cent dilution for the mining width under consideration. The potential for stress damage related overbreak should therefore be considered as part of any assessment of narrow vein dilution.

Jan 1, 2005

By M Hedley

Tracking plant and personnel in underground environments provides multiple potential benefits for a mine including increasing safety, better monitoring of production, traffic control, and in the future monitoring and control of autonomous vehicles. The main techniques for wireless tracking are to use radio frequency identification (RFID), signal strength based techniques, and time of arrival (TOA) based techniques. RFID does not provide continuous tracking and signal strength techniques have poor accuracy in the complex radio propagation environment present in mines. TOA based techniques are potentially the most accurate, but most current equipment does not realise the potential of the technique. CSIRO has been developing the wireless ad-hoc system for positioning (WASP) system for wireless tracking in a range of challenging environments including underground mines. WASP has been licensed for sporting applications and has delivered encouraging results in early trials for a surface and an underground mining application. The system utilises a number of ‘anchor nodes’ that are placed at surveyed fixed locations within the mine, and tags attached to plant or personnel to be tracked. The system provides an ad hoc data communication network, thus wired data connections are not required to the anchor nodes. WASP uses transmissions in the 5.8 GHz ISM (instrumentation, scientific and medical) frequency spectrum to perform highly accurate ranging between nodes, hence tracking of tags. The localisation performance of the system depends upon the radio propagation environment, ranging from 0.1 m in low multipath conditions. In this paper we describe the WASP system and provide results of initial testing in an underground mine that shows that the system achieves high ranging accuracy, hence localisation accuracy.

Mar 21, 2011

By d&apos, Alton AJ, Rigden DT

Modern petroleum refining offers a complexity of environments, each requiring different metals for the satisfactory performance of-the various sections of the refinery, and this paper first outlines the varied enva.x¦on-ments thus met.It follows that the metal types in use will also vary to suit each particular environment, and the paper' consequently covers the use of ferrous-metals, ranging from plan carbon steels to the high alloy types and the non-ferrous metals, particularly copper and its alloys.The failures of some,of these metals and alloys are then illustrated by experiences it Kwinana. These failures are duo to (a) corrosion, (b) erosion, (c) faulty welding, and (d) mechanical defects,' of which the first is by far the most prevalent. The protective measures taken to prevent subsequent failures are then given under one or other of the following headings :(1) alterations in process conditions, (2) the use of alternative ,alloys,(3) suitable heat treatment, (4) redesign of the failed section, (5) cathodic protection, and (6) use of corrosion inhibitors.Reference is then made to the use of specialised metals and alloys.Metals, generally in the form of oxides or salts, are also used as catalysts in refining processes. Activated alumina is used, combined with silica .forScracking' of heavy oils, and as a support -for platinum, cobalt, molybdenum, nickel and similar metals, which catalyse hydro-genation and dehydrogenation-processes. .In the final formulation of petroleum products metallic compounds may be added. Reference is made to the large quantities of lead used by the petroleum industry and to the use of metallic soaps and detergents in the formulation of lubricating oils and greases.

Jan 1, 1962

The investigations of the Leningrad ruining lilstitute on this problem are carrying out in the following main directions: 1) The analysis and study of contaminants migration at particular sites of mining development; 2) The working out of theoretical and me- thodical basic principles of aquifers migration tests; 3) The work- ing out of methods of the forcasting of groundwater pollution pro- cesses; 4) The theoretical and uethodical substantiation of hydro- geological observations of groundwater pollution processes; 5) The wort ing out of the measures at the groundwater control and their rational use at the particular sites of mining development. The research that have been carried out by the present moment have covered the wide range of wining and geological conditions -- as from the point of view of specific genetic types of water-be- aring rocks (porous, fissured and fissured-porous), as well as from the point of view of pollution sources (surface waste water basins and underground basins of non-standard water) and the cha- racter of the latter's migration (tracers, physically neutral ef- fluents, heavy or light ones). The combination of specialized mi- gration tests and observations carryed out at uoayi, sites, as well as the following ar~,alysis o:i the data of field study allowed to get useful theoretical, methodical and practical results on the all directions above mentioned, ns the summing up of these results the author proposed the concept of controlled ground :ester polluti on. This conception is based on three whales" - groundwater self- purification, engineering prevention measures and ground-water monitoring correlated with each other by succes i.vely refined (ac- cording to the observation data) hydrogeologicZl forecasts.

Jan 1, 1988

At the Nikkel og Olivin nickel mine near Narvik, Norway, Outokumpu has been the operator since 1993. The mine was opened in 1989 and in 1992 Outokumpu commenced operations to secure concentrate deliveries to Harjavalta's nickel smelter in Finland. Annual production is about 740 000 tonnes of nickel ore grading 0.5 per cent Ni, about 25 000 tonnes of nickel concentrate and about 2800 tonnes of nickel metal. All production comes from underground operations which makes Nikkel og Olivin AS perhaps the lowest grade underground nickel mine in the world today. Production is currently from one of two orebodies, which is known as the Western orebody. The Eastern orebody was worked out by 1995. During Outokumpu's operational period the Western orebody has been delineated and taken to production. The underground exploration and definition drilling involved about 15 000 in of diamond drilling, which was carried out during a nine-month period. Following this a feasibility study was undertaken and production commenced. Improvements were made to the mining methods. Previously the mine utilised open pit equipment underground and this resulted in an enormous amount of additional tunnelling. Grade control and ore delineation were previously based on sparse diamond drilling and all geological information was processed manually. The improvements included the use of underground sludge drilling to increase the amount of geological information, the of a new computer system for grade control and mine planning, new automated underground longhole drilling equipment and the of underground mining equipment which reduced the size of the drives. These changes produced a marked increase in the efficiency of the underground Mine.

Jan 1, 1996

By E Werner, B R. Leavitt

The chemistry of acidic mine drainage discharging from flooded coal mines is commonly reported to improve with time after flooding. This investigation describes a 18-year dataset of post-flooding water chemistry for a below-drainage underground coal mine within the northern Pittsburgh coal basin (Pennsylvania, USA). The Montour mine is a 5650-hectare below-drainage coal mine of maximum 260 metres depth. Montour was closed in 1980 and flooded to within 38 metres of land surface within 4.8 years. Pumping averaging 210 L/s was then employed to maintain water levels at this elevation. The flooded proportion of the mine (by volume) at full flooding was 56 per cent. The shaft where water was pumped from Montour for water control is located about 70 per cent of the distance between the mine water table and the back of the mine ù that is, it is close to the back of the mine. The residence time (total water volume at flooding divided by pumping rate for control) is estimated at 5.6 years. Time series of chemical analyses show three phases of chemical behavior in post-flooding discharge. In Phase I (zero to two years after flooding), iron concentrations were high and reached their maximum (1100 mg/L). In Phase II (two to four years after flooding), a transition was begun to alkaline conditions, with decline in iron and other solutes. In Phase III (>4 years), net alkaline conditions began, with iron concentrations declining exponentially to 50 per cent of mined volume. This attainment of net alkalinity in this case may have also depended on abundant calcite in overburden extended up to 30 m above the mine floor.

Jan 1, 2003

Comminution of solids is surely one of the oldest technologies which even in this day and age of DNAs, chips and space exploration continues to challenge our scientific acumen and engineering ingenuity. In essence, this challenge is two-fold. One, as much as three to four per cent of all electric power generated world-wide is consumed in crushing and grinding primarily because the utilisation of energy is woefully poor. Studies have shown that the efficiency of mechanical size reduction processes is of the order of 1.5 to 12 per cent only (Schoenert 1986). Two, with the grinding technologies available to us, we have, at best, inadequate and, at worst, almost negligible control over the shape of the comminuted particles, size dispersion of the ground mass, and the sharpness of mineral liberation. Low energy efficiency and lack of control in the sense mentioned above have far-reaching implications for resource conservation, performance of down stream unit operations, and damage to the environment. Our problem is in fact central to the mineral-energy resources triangle shown in Figure 1 which depicts the close interrelationships among mineral resources which are becoming poorer in content and more complex in mineralogy each day, energy resources which are depleting rapidly without any viable alternate on the horizon, and environmental concerns which can no longer be ignored. It is evident that any improvement in the efficiency of the comminution process impacts directly on the control of environmental damage, conservation of energy and the economics of the operation. These concerns have special relevance for the processing of non-ferrous ores.

Jan 1, 1992

By Binns MJ

Gold/silver orebodies of the Golden Plateau deposit, Cracow, Central Queensland, are currently being exploited by the Cracow Mining Venture. A geostatistical block model has been prepared to assist with long term mine planning. The Golden Plateau orebody, of inferred epithermal origin, is a multiply brecciated, silicified fault complex containing irregular, tabular and pipe- like oreshoots. Historically the lode has been stoped and open cut over a strike length of 750 metres at widths of up to 15 metres and to a depth of 250 metres. The Golden Plateau mine produced 1.55 million tonnes of ore at an average grade of 12 g/t Au and 13.5 g/t Ag over a 42 year period. In the preparation of the reserve model much reliance has been placed on recent diamond and reverse circulation drilling (71 holes in total). However a significant volume of data has been derived from historical level assays and underground diamond drilling. Over 3,000 level assays and 50 underground drill holes contributed to the database. Similar lognormal populations were observed for 1 metre composite grades from each major drilling campaign once corrections were made for core loss. Cumulative frequency plots revealed only one outlier which was cut to the population line. The population statistics from the historical level assays showed a significant difference from those derived from the drill hole composites. Level assay populations were cut to local drill hole populations before incorporation into the ore reserve model. The resulting data has yielded interpretable variograms, the parameters of which have been applied to the preparation of a kriged block model of the deposit.

Jan 1, 1987

By Bourne R. W, Smith T

This paper presents initial findings of a project examining novel processes for the treatment of refractory sulphidic gold concentrates. Non-oxidative roasting of such concentrates for 12 hours at 750¦C resulted in the finely disseminated gold agglomerating to form discrete grains. The pyrite and arsenopyrite decomposed to form pyrrhotite, whilst the labile sulphur and arsenic driven off was collected on a condenser as a mixture of elemental sulphur, metallic arsenic and various arseneous sulphide compounds. As a result, the cyanide solubility of the gold contained in sulphidic refractory gold concentrate from the Emperor mine in Fiji improved from 54.5 per cent to 98.4 per cent; from the Fimiston mine in WA (65.2 per cent to 96.6 per cent), from the Windarra mine in WA (69.6 per cent to 91.3 per cent), from the Harbor Lights mine in WA (20.4 per cent to 60.7 per cent), and from the Wiluna mine in WA (12.6 per cent to 28.0 per cent). The non-oxidative roasting conditions have not been optimised for each of these minerals. Subjecting the non-oxidatively roasted minerals to mild oxidative acidic iron sulphate pressure leaching (with typical temperature of 100¦C and typical oxygen overpressure of 500 kPa) to remove iron and so further liberate finely disseminated gold, resulted in the cyanide solubility of the gold exceeding 96 per cent for each of these five concentrate types (including those from Harbor Lights and Wiluna). Thiourea leaching of the sulphur-rich residues under acidic conditions resulted in remarkably high gold extractions being achieved. These novel processing options need to be optimised, and their economic viability established.

Jan 1, 1991

By K Williams

Marvel Loch South Pit has had a number of stages of open and underground mining activities before acquisition by Sons of Gwalia. The historical pit had achieved a completed pit depth of 150 metres and the shaft and decline mine had reached approximately 220 metres in depth using open stope mining methods. The various mining methods reflect the various economics and industry practice at the time. The South Pit ore zones are medium grade (~2.5 g/t) but have a regular geometry and large tonnes per vertical metre. A number of studies have been completed up to a pre-feasibility stage looking at options to extend the pit depth and to lower the unit cost of gold production. The options considered were the re-optimisation of the pit to determine further cutbacks or the innovative use of an in-the-wall ramp. The in-the-wall ramp (tunnel) would permit the removal of the in pit ramp to expose additional ore that was within the footprint of the ramp design and to provide the opportunity to increase the final pit depth. Similar mining method has only been used at Three Mile (Coolgardie, WA) and Chalice Mine (Norseman, WA). The tunnel would serve as a gateway for further extension of the south mine and the central ore zone via underground mining methods. The ultimate depth of the South Pit has been extended to 310 metres below surface and significant additional ore has been recovered. This paper will give an insight into the various studies to optimise the Tunnel mining method, the determination of the various tunnel dimensions, and the phases of mining to arrive at the completed design.

Jan 1, 2003

THERE are few industrial and metallurgieal processes which do not require the application of heat energy, and the modern demand for increased working efficiency has resulted in attention being paid to temperature control as a means of ensuring fuel economy and more efficient plant operation. In general, mill accuracy required is not very contant in laboratory work, and few industrial operations are controlled to within less than 5° while in many cases greater limits are allowable. Almost every thermal property of matter has been suggested as a basis for the construction of pyrometers, but the thermo-electric type finds by far the widest application, and hence this paper will deal only with the principles, construction, and uses of this type of instrument. THERMOELECTRIC PYROMETRY.In the year 1821 Seebeek discovered that if the ends of two dissimilar metal wires were joined and one junction heated, a current flowed in the circuit, and the KMF (electro-motion force) set up could be measured by inserting a galvanometer at the cold junction. The phenomenon was not thoroughly investigated for many years, but, as the demand for high-temperature thermometers increased, several investigators, of whom Le Chatelier was one of the pioneers, successfully endeavoured to utilize the principle in pnometric construction. The couples which gave the most satisfactory results were discovered, improvements were made in material and design and the present-day type of instrument gradually evolved. The apparatus consists of three main parts, viz. (1) The thermo-couple itself of two dissimilar metal or alloy wires together at one end. (2) The leads which connect the terminal of the thermo-couple with the measuring instrument.

Jan 1, 1923

The Northern Mariana archipelago in the W.Pacific forms a classic intra-oceanic island arc system far from the influences of continental crust. As such it offers an ideal location in which to study many of the problems of subduction-related volcanism. Radiogenic (Sr, Pb, Nd and Hf) and stable (0, S and H) isotope systems have been applied to the question of the possible involvement of components from the subducting slab in arc magmagenesis. The results contrast with earlier studies based upon limited sample suites and suggest that fluids, derived from the slab and enriched in mobile elements, substantially modify the composition of the mantle wedge and contribute to the characteristic geochemistry of arc magmas. Trace element data, including the occurrence of negative Ce-anomalies in the lavas seem consistent with this conclusion. Major and trace element variations within the arc lavas can be modelled in terms of crystal fractionation of a gabbroic mineral assemblage and mixing calculations indicate that this has the approximate composition of PLAG:CPX:MAG:OLIV = 60:25:10:5. This observation is compatible with the widespread occurrence of gabbroic nodules in lavas throughout the arc. Consideration of Rare Earth Element and phenocryst data leads to the conclusion that many of the more basic lavas may be the products of cumulus enrichment. The results of this study constitute a model for magmatic processes occurring in simple island arc systems, and may be generally applicable to other, more complex settings. The recognition of a return flux of material with 'continental' affinity to the mantle, via sediments on the subducting slab, also places strong constraints on geochemical models of crust-mantle evolution.

Jan 1, 1987

By Wall J, Platell R, Knight P

The Argyle diamond mine is located in the East Kimberley area of Western Australia, some 100 km south of the town of Kununurra. The diamondiferous Argyle olivine-lamproite diatreme was discovered in August 1979. Production began in December 1985 at a planned throughput of 3 Mtpa to recover 25 million carats of diamonds. Presently, Argyle is the world's largest producer of natural diamonds and produced over 40 million carats in 1993 from seven million tonnes of lamproite ore treated. Two phases of evaluation have been carried out. The first in 1981-82 was designed to prove around 60 million tonnes of ore to justify the establishment of a mine with a minimum life of 20 years. The second phase, in 1989-90 involved drilling the orebody to greater depths to provide data on which to plan the final pit design. The final pit contained 120 million tonnes of ore at 5.3 carats per tonne (ct/t) grade. Mining of the planned pit will extend the mine life to around the year 2004, following which it is possible that a further cut-back could be mined. There is also the potential for future underground mining. A substantial amount of geotechnical work has been undertaken due to the fact that the pit will be nearly 500 m deep and is located in a mobile zone causing abnormally high residual stresses to occur in the pit walls. The occurrence of low strength rocks at depth in the pit walls further complicated the situation. Hydrogeological investigations were done to determine pit dewatering requirements and to assess the effect of dewatering on pit wall stability.

Jan 1, 1994

By E Ben-Dor, D Bakun-Mazor, Y Ben-Ari

Determining the mechanical properties of rocks is important for various civil engineering fields, including the mining of raw materials for aggregates used in the construction and paving industries. Traditionally, the mechanical properties of rocks are obtained through in situ and laboratory tests during geotechnical surveys. However, these time-consuming surveys involve many resources. In contrast, hyperspectral remote sensing methods make it possible to identify the mineralogical composition and crystallographic structure of the rock; properties that control the mechanical properties of the rocks. In this work, we characterise the mechanical properties of carbonate rocks by using a hyperspectral sensor in laboratory conditions. We collected about 150 cylindrical samples of carbonate rock, with a wide range of strength values from several rock outcrops in Israel. We used a point spectrometer in the range of 0.4–2.5 μm and a spectral image sensor in the range of 3.0–12.0 μm, scanning the samples to obtain the signature of their light reflections and spectral emissivity. We then measured the samples’ density, porosity, water absorption, and uniaxial compressive strength (UCS). We used sophisticated data mining to find statistical relationships between the hyperspectral signatures of the samples and their mechanical properties. We used this data to identify the most dominant wavelengths for predicting mechanical properties. We found that the density, porosity, and water absorption of carbonate rocks could be confidently predicted based on spectroscopy data, while the UCS of the rock could also be predicted, but less significantly. The results of the study pave the way for the development of measuring tools for the mechanical properties of rock, based on non-destructive tests of quarrying materials.

Nov 29, 2022

By Finlayson J. F

The advantages of rapid and accurate analyses are becoming appreciated in many industries today and have resulted in a great increase in the number of samples received by their laboratories. This has caused some firms to consider the installation of one or more of the instruments available for analytical chemistry. In this country there are relatively few people with experience of instrumental methods and it is difficult for a firm considering the installation of such equipment to assess the advantages which instruments may give them, and to decide which instruments, if any, will be of most use to them. The object of this paper is to give a brief survey of instrumental methods in the field of inorganic analysis. Instrumental methods of analysis have numerous advantages when used correctly. They enable extremely rapid analyses to be made in many cases, e.g., analysis of refined lead by purely chemical means takes about two days whereas spectographically the analysis can be completed in approximately one and a half hours. The accuracy ofinstrumental methods, generally between 1 and 5%, is higher than most chemical methods for small percentages of impurities. Furthermore, if the instrument can be calibrated against absolute standards the errors are usually random and not biased to one side of the correct result. The sensitivity is high, enabling in many cases the detection and determination of smaller percentages than can be detected chemically. This high sensitivity enables and, in some cases, requires the use of very small samples, and results in considerable savings in reagents, allowing the analysis of considerably more samples without undue loss...

Jan 1, 1951

By Edmonds G. A

The power station went into operation in 1931, when the installed capacity was 12,500 kVA. with a loading of 4,000 kVA. In 1936 the loading increased to 6,750 kVA. which necessitated the addition of a third set which went into operation in 1937, the installed capacity at that date being 18,750 kvA. with a loading of 7,000 kVA. This remained fairly constant until 1945, when a gradual increase was noticed, the loading in 1952 being 10,598 kVA.With the addition of the copper plant, additional generating capacity was required and it was decided to raise the installed capacity by the addition of a fourth set to 34,375 kVA. with an expected loading, when producing copper, of 20,000 kViA.MAIN POWER PLANTThis consists of three GiE.e. alternators of 6,250 kVA. or 5,000 kW. at 0.8 P.F. rating and one G.E.C. alternator of 15,625 kVA. or 12,500 kW. at 0.8 P.F. rating, making a total generating capacity of 34,375 kVA.Each alternator is driven by Fraser and Chalmers turbines at 3,000 r.p.m.SYSTEMThe main 3 phase 3 wire 3,300 volt distribution system has the neutral point of alternators earthed through by one or two earthing resistors designed to limit earth fault current to 3,000 amp. for 20 seconds, in the case of the large machine, and to 1,100 amp. for 10 seconds, in the case of the smaller machines, or full load of either size machine at rated voltage.

Jan 1, 1953

By Juniper LA

ERM Consultants Pty Ltd was established in 1980 for the purpose of introducing a disciplined coal technology and power station planning service, to support Australia's efforts in establishing a major export steaming coal industry. At that time, major coal exploration programs were mounted on more than 50 potential export coal deposits with proven open-cut reserves to export 200 Mt/a of coal. The fact that Australia achieved an export trade of only 30 Mt/a, equivalent to the energy requirements for a population of around 5 million people, illustrates the very small achievement to date. The main reasons for this small export steaming coal growth have been: 1. Failure to convince potential overseas coal buyers of the benefits of coal-fired power generation, and the ability of proper power station design to overcome environmental problems, and achieve reliable operation and long life when burning Australian coals. 2. Failure to promote Australian power engineers to advise on the use of Australian coals, resulting in Northern Hemisphere power station experience dominating in market countries. 3. Failure of governments to draw on privately practising Australian power engineers and coal technologists in technical workshops, presentations and assistance to overseas countries, to ensure that personnel whose business it was to serve the follow-on needs of countries were readily available. The result of these failures has been that: 1. Only a fraction of prospective overseas coal-fired power projects have proceeded. 2. Australia has had no influence in the design of overseas power stations to ensure that potential customers would be confident that Australian coals could be reliably burnt in their boilers.

Jan 1, 1987