Search Documents

By S MacKinnon, J Kok

Potential areas for improvement in flotation performance were identified during JKTech model development surveys in October 2003. Subsequent implementation of the JKTech recommendations in consultation with flotation cell manufacturer Outokumpu have resulted in gold flotation recovery increases of more than four per cent over a two-year period. One of these recommendations was the installation of High Shear Stators in the Cleaner and Recleaner flotation cells. The High Shear Stator installation project was justified based on simulations completed using JKSimFloat. Bubble size measurements completed before and after installation of High Shear Stators showed a reduction in mean bubble size of approximately 50 per cent in the Cleaner cells. Both Cleaner and Recleaner banks showed a significant narrowing of the bubble size distributions following the installation. Plant gold recovery increase resulting from the installation of High Shear Stators was 1.1 per cent, with a 1.9 per cent increase in flotation gold recovery and 5.4 per cent increase in flotation sulfur recovery. Based on the 1.1 per cent recovery increase and total project cost of less than $200 000, the High Shear Stator Project NPV was $8 200 000 with a 0.25 year payback period.

Jan 1, 2006

By O Ostrovski

Direct iron smelting reduction has been examined using a modified 50 kg induction furnace. The furnace was equipped with continuous raw material feeding, a top oxygen lance, argon bottom bubbling, and sensors for measurement of gas and bath temperatures, gas composition and other parameters. In the base case, iron ore was charged at the rate of 1.5 kg/h, coke flowrate was adjusted to maintain a char fraction in the slag at 30 wt per cent, the oxygen flowrate was 100 Nl/min and the post-combustion ratio (PCR) was 60 per cent. The PCR was varied from 45 to 75 per cent by changing the lance height relative to the bath surface. Smelting reduction of Whaleback iron ore was investigated at different post-combustion ratios and iron ore feedrates using coke and coals with different volatile matter. The rate of iron oxide reduction increased with increasing iron oxide concentration in the slag, with a slight deviation from a linear function. The post-combustion ratio affected iron ore reduction and partitioning of elements between phases in the smelting reduction furnace. The high volatile coal investigated was found to be unsuitable for iron smelting reduction in the laboratory furnace.

Jan 1, 2000

Geologists employed by Metals Exploration Pty. Ltd. discovered nickel enrichment at Greenvale, 180 kilometres West of Townsville, in 1967. Subsequent drilling proved an ore body containing 45 million dry tonnes of ore containing an average of 1.5% nickel and 0.11% cobalt. The Freeport Minerals Company, who had experience in treating lateritic nickel ore, were invited to participate in development of the ore body. This resulted in the formation of the operating company Queensland Nickel Pty. Ltd., jointly owned by Freeport Queensland Nickel Inc. and Metals Exploration Queensland Pty. Ltd. With the completion of successful pilot plant testing of Greenvale ore at the Freeport research facilities at Belle Chasse, Louisiana, a treatment plant was constructed at Yabulu, 24 kilometres North West of Townsville. A 225 kilometre railway line was built connecting the Greenvale Mine and Yabulu Treatment Plant. The ore reduction and ammonia/ammonium carbonate leaching flowsheet is similar to that constructed and operated by the Freeport Minerals Company during World War II at Nicaro, Cuba. Modifications to the Nicaro flowsheet implemented at Yabulu include facilities to recover cobalt in a mixed nickel/cobalt sulphide product and the reduction of nickel

Jan 1, 1978

While South Africa is well endowed with mineral resources, it is generally accepted that its future will be determined more by the development of its human resources than its mineral wealth. The country has throughout its modern history suffered from an over-supply of unskilled labour and a shortage of skilled and professional manpower. There has furthermore always been an over-reliance on Whites as an internal source of professional manpower, supplemented by immigration wherever possible. Better utilisation of other population groups in professional positions has been hampered by the general lack of education and training among such groups. Although many problems still remain, there are emerging trends which are likely to positively affect the training of professional manpower in the future. The direct and indirect influences that are likely to affect professional training at the macro level include 1. government policy and objectives in respect of manpower education and training, 2. the emergence of technikons as fully- fledged tertiary education institutions, 3. demographic trends in South Africa as they pertain to education, 4. political and statutory developments in the country, 5. industry involvement in tertiary education, and 6. professional registration.

Jan 1, 1986

By V S. T Ciminelli

This work aimed at evaluating the acid rock drainage (ARD) potential of five samples of a Brazilian gold sulfide mine in a decommissioning process. Three of the most traditional ARD prediction techniques, Standard Acid Base Accounting (Std ABA), Modified Acid Base Accounting (Modified ABA), as static methods, and humidity cells as a kinetic method were tested. Both the Std ABA and the Modified ABA results indicated an acid generation potential for some of the studied samples. In the other cases the results were inconclusive. The five samples were then submitted to humidity cell tests during 27 to 30 weeks. At the end of the period, the leachate pH was stabilised in a range from 3.4 - 4.1 (four samples) to 5 (one sample). The presence of relatively high levels of sulfate and dissolved metals was detected throughout the operation, specifically, Ni and Zn, and less frequently, As. These findings are discussed with the help of the samples mineralogy and Eh-pH diagrams. The results obtained in this investigation indicated potential environmental risks of this mining area. In this particular case, the kinetic tests were shown to be essential to the identification of the samples ARD potential.

Jan 1, 2003

The Nagambie heap leach gold mine commenced production of gold in September, 1989. The mine,120km north of Melbourne in Victoria, Australia, was developed by Perseverance Mining Cor- poration Ltd, a junior Australian mining company, with no other operating mines. Gold production to December 31, 1990 was 47,621 oz. The mine is now producing at the rate of about 45,000 oz per year. As of February 28, 1991, resources at the mine are 5.1 million tonnes measured, at 0.65g/t Au while reserves were 1.65 million tonnes at 0.86g/t Au of proven, heap leach ore, plus 0.37 million tonnes at 0.40g/t Au, of dump leach ore. Metallurgical recoveries expected are 80 per cent for the heap ore and 60 per cent for the dump ore. Perseverance Mining Corporation was listed on the Australian Stock Exchange on April 2, 1987, after a capital raising in March that year. At this time the company's issued capital was 4 million ordinary 25ó shares, 3 million of which were issued to the public to raise $0.75 million.

Jan 1, 1991

By Peak DJ, Kearton CJ

Following a summary of the development of a BF model using aerodynamic relationship and bulk fines index a blast furnace policy model is presented complete with the development of nomograms and featuring production rate, oil rate and total fuel rate. Application of the blast furnace model is then illustrated using No. 5 Port Talbot as an example. It is also shown how the policy model assists in ore allocation in the British Steel Corporation. Further developments which have recently occurred in the correlation between the bulk fines index and the permeability coefficient are detailed and a comparison made with a number of furnaces operated elsewhere. The implications of the comparisons made are that high driving rates are possible with burden containing a high proportion of sinter only if the burden behaviour in the lower parts of the furnace permits high driving rates with a steady gas distribution and low pressure drop. It is concluded that the value of a simple set of equations resulting from the model assisted furnace operators to pin-point likely causes of failure to reach or sustain target production rates.

Jan 1, 1975

The Lennard Shelf Operations owned by Western Metals Ltd evolved from the Cadjebut Zinc Lead Mine (BHP) in August 1994. Original production of 0.5 mtpa will rise to 2.0 mtpa at the end of 1998. Employees work a multiple of fly-in/fly-out (FIFO) rosters from the Kimberley region and the WA Capital. The three underground mines, treatment and services departments will employ approximately 300 people by the end of 1998. The expansion of the Lennard Shelf Operations as a remote mining location was based on a fresh look at management systems and employee rosters which were generated from many years of mining experience. This paper will endeavour to summarise these experiences and analyse some of their outcomes. Dealing with several mining methods, engineering difficulties, logistical problems and climate extremes, the Lennard Shelf Operations has managed social/employee issues with excellent results. Much time has been spent to get this correct for the Lennard ShelfÆs own set of circumstances. Employees and associated companies must expect continuing changes and improvement as Western Metals strives to continually improve its management systems and employee rosters.

Jan 1, 1998

The last two years have seen a rapid change-over from mechanised cut and fill. stoping to the more economic and productive long hole open stoping method, such that today more than 80 per cent of total production is won from open stopes. At first drilling was by sub-level rings and/or parallel up and down holes from inter- mediate sill horizons using conventional exten- sion rod equipment. Sub-levels were developed no more than 40 metres apart to allow accurate drilling. Compact, crawler mounted in-the-hole hammer equipment was introduced as soon as it became available in Australia. Today, all open stope drilling is done with three Atlas Copco ROC306 rigs and two Ingersoll-Rand CMM jumbos. Fans of 115 mm diameter holes, varying from near vertical down holes to horizontal, are drilled with a burden of 3 m. Toe spacing varies from 3.5 m to 4 m. An Atlas Copco DG418 booster compressor is used to boost run-of-mine air from 700 kPa to 1400 kPa in the areas of longest drilling. This has improved overall drilling performance in these areas by 40 percent.

Jan 1, 1977

My early experience with the coal industry was in the latter half of the 1970s, where attention to only ones own æaccidentsÆ and concentration on behaviour controls were impeding the introduction of effective engineering controls such as ROPS, FOPS, roof support and residual current devices. Lack of the broad picture of personal damage and of relevant veridical (true saying) knowledge and data had to be overcome to achieve progress in reducing fatalities. Thirty years on, it is again necessary to take stock. How good is our knowledge, our data, our information on which we make decisions. Despite Australian all industry 1992-93 data showing 80.5 per cent of costs came from occurrences which permanently altered peopleÆs lives, New South Wales is still the only state reporting permanent disabilities. In 1991 - 1992, the rate of permanent disability per 1000 wage and salary earners was two. In 2000 - 2001, it was over four û more than doubled. Also strongly motivating is the huge cost. Industry carried 25 per cent of the $34.3 billion costs for 2000 - 2001, up ten per cent of 82.8 billion if the costs of pain, suffering and early death are included.

Jan 1, 2005

By M Gao, V Lawson, W Valery

Changes in metal prices and mine output over recent years have required the Copper Concentrator of Mount Isa Mines to operate at annual tonnage rates varying from 4.0 million to 6.5 million tonnes. Several circuit combinations were operated during this period utilising up to two semi-autogenous grinding (SAG) mills and up to two ball mills. The aim was to maximise grinding efficiency and keep unit costs constant regardless of throughput rate. Measures to improve the SAG-ball mill unit operation were implemented with each circuit change. These included installation of a splitter to divert SAG Mill cyclone underflow back to the mill, increase SAG ball charge from four per cent v/v to eight per cent v/v, reduce in SAG top feed size and increase of ball mill grinding medium size. Modelling work and surveys led to a new design of the SAG liner profile from 60 rows of rail bar liners in a high-low arrangement to 40 rows of top hat liners in a high-high arrangement. An on-line SAG Mill feed sizing monitor was recently installed to improve grinding control.

Jan 1, 2000

By West Coast Staff

Attention to the design of facilities for drainage, of both surface water and seepage, made it possible to attain, for a qam impounding residues from a concentrating mill, a more stable sand wall which can eventually be carried to a greater height.EXPERIENCE WITH No. 1 DAMResidue from the lead zinc concentrating mill, which treats the ore from the Rosebery and Hercules Mines, was pumped 3,600 ft. through a 5-in. diameter woodstave pipeline to the site of the dam. It was formerly delivered through a 4-in. steel pipeline.State laws prevent the residue being discharged to waste into the Stitt River. Furthermore, as a pyritic residue it is a potential source of sulphur.Between 1936 and 1956 more than 1,000,000 tons. of residue was paddocked. The run-of-mill product was roughly classified at the dam in a 6-ft. diameter cone classifier and the sand fraction was pumped by a 3-in. pump to the front wall of the dam across a shallow valley. The overflow gravitated to the rear of the dam (Fig. 1). Typical sizings were:

Jan 1, 1958

By S Hapugoda, Y Tang, L Lu

The steel industry is one of the global leading CO2 emitters, accounting for approximately 7 per cent of global anthropogenic CO2 emissions. In 2022, the world produced 1878.5 Mt of crude steel. About 70.8 per cent of the world’s crude steel was produced by integrated steel mills through the blast furnace and basic oxygen furnace (BF-BOF) process, while the remainder was produced largely by mini mills using electrical arc furnaces (EAF). Compared with gas-based DRI and scrap-based EAF processes, the direct CO2 emissions from the BF-BOF process and the coal based DRI and EAF process are significantly more, as both the processes rely heavily on fossil fuels, such as coke and pulverised coal, to provide energy and reduce iron oxides. Hydrogen is very reactive and reduces iron oxides to metallic iron without generating CO2. Therefore, substitution of hydrogen for fossil fuels in these processes presents a good opportunity to significantly decarbonise the steel industry. This paper will first discuss the thermodynamic and kinetic characteristics of hydrogen and carbothermic reductions of iron oxides and then examine the behaviours of different ore types present in Australia iron ores during hydrogen reduction.

Sep 18, 2023

By A Bennett, A Peck

BHP has recently constructed a Hot Briquetted Iron Plant at Port Hedland in the Pilbara region of Western Australia. Supply of iron ore fines to the plant is by conveyor from the companyÆs existing Nelson Point stockyards. The conveyor passes under Port Hedland harbour in a concrete segmentally lined tunnel, approximately 1030 m long and with a 5.1 m external diameter. The tunnel was constructed by a Tunnel Boring Machine (TBM) which both excavated the ground and erected the tunnel lining. The tunnel was bored between cut and cover in situ concrete portal structures, the TBM being launched from the Finucane Island side towards Port Hedland town. The alignment required lengthy gradients of 1:6 on either side of the harbourÆs dredged channel, under which the tunnel is bored with a minimum clearance of 8 m.The tunnel is fitted-out with:1800 mm belt conveyor capable of 10 000 tph;walkway along which a specially designed inspection/ maintenance vehicle can run; andtunnel services including power, light, fire detection and suppression communications, water mains for wash down and sumps and pumps for drainage.This paper gives a general overview of the design and construct contract, important aspects of the design and the construction process itself.

Jan 1, 1999

By A Halim

The European Union (EU) have recently issued new Threshold Limit Value-Time Weighted Average (TLV-TWA) for diesel exhaust contaminants, which are CO, NO2 and DPM. The new limits for CO and NO2 were issued in 2017 whilst the one for DPM was issued in 2019. However, in order to allow EU mines to formulate strategies to comply with these new limits, the EU granted a transition period in which mines could use the old limits until the new limits are enforced. The new limit for CO and NO2 will be enforced from 21 August 2023 whilst the one for DPM will be enforced from 21 February 2026. The new limit for NO2 and DPM is very low, 0.5 ppm for NO2 and 0.05 mg/m3 of Elemental Carbon (EC) for DPM. Combination of these two limits would be the lowest among all mining jurisdictions worldwide. It poses a huge compliance challenge to EU mines if they keep using diesel machines. Therefore, a study and a field trial were carried out by the author in 2019–2021 to investigate whether replacing diesel machines with Battery Electric Vehicles (BEVs) would be the best answer to this challenge. This paper outlines results of this study and field trial.

Oct 12, 2022

By G Cormack

By designing comminution circuits for mineral liberation rather than the final recovery process and by using high mass pull gravity recovery, the concept of underground processing has become a reality. Gekko has found that many ores respond favourably to fine crushing with either high pressure grinding rolls or vertical shaft impactors which when combined with the InLine Pressure Jig gravity separator and coarse flotation results in a narrow, low-head, compact processing plant that can be sensibly fitted in existing underground openings. The focus on fine crushing reduces the power requirements of the plant to approximately 5 kWh/t for a capacity of up to 20 t/h run of mine ore feed. The use of water recycle systems places no extra load on the mineÆs normal water handling system. GekkoÆs underground processing plant, the æPythonÆ, has been designed to be towed down the decline or lowered down a shaft and is capable of being installed in sloping, non-linear drives for placement close to the working face. The overall benefit to mining companies of this concept has been estimated to be a significant operating cost-saving, lower cut-off grade and a significantly smaller environmental footprint.

Jan 1, 2008

Commencing early in 1975, Saraji Mine in Central Queensland will product 3.56 million tonnes in the first year and then 4.57 million tonnes annually for the Japanese and European markets. The coal will be mined from a series of pits separated by corridors which will be mined at a later date. Through the corridors flow regional drainage structures and power lines. Relatively easy areas will be mined initially to assist the cash flow and to minimise start-up difficulties. For ease of scheduling it is desirable that pit lengths exceed 3 000m but this will not always be possible. Ramps were designed using 1 200m spacing and 5 per cent gradient as optimum but modified to suit specific conditions. One ramp will be in the end of each pit nearest the ROM hopper and stripping will commence from this end. The advantages so gained are shorter haul distances, immediate access to the coal after stripping and simplification of the excavation of the first ramp. Haul road location was defined by the minimum present value of construction plus operating costs. Road design utilised airfield construction charts because wheel loads were outside the range of available road design manuals. Low load resistance characteristics of

Jan 1, 1974

By Jaracz K

At the operation of mine winders in deep shafts considerable oscillations of winding ropes may occur due to elasticity of both wind-ing and balance ropes. The amplitudes of longitudinal oscillations may reach + lm at relatively low frequencies, ranging from 0.5 to 2 c/s. These oscillations may be dangereus for the rope and produce several hazards to the winding installation as a whole. They may cause conside-rable instant accelerations on the pulley and dangerous tensions in ro-pe wires. The excessive acceleration may cause the uncontrolled rope slip on the pulley. Several methods of limitation of these accelera-tions were developed, some of them have been already in control system: of electric drive of the winder. The most simple ones are: a/ limita-tion of the rate of change of acceleration and retardation of the win-der /so called "jerk"/ and b/ the proper selection of regulators of the winder control system to get the optimal control. The trouble in solv-ing the problem of rope oscillations is that the dynamic system of the winder is a nonstationaryone owing to changing distance of conveyance from the pulley. Besides, the system is described by the equations with distributed parameters. The brief discussion of the theory and its practical aspects are enclosed as well.

Jan 1, 1985

A synthetic gold-silver telluride material (mainly sylvanite) has been prepared and its physical and chemical properties checked. Flotation tests using a Hallimond tube were conducted using commercial xanthate collectors. At collector concentrations of 10-3M with the addition of 5 × 10-4 M CUS04, no obvious differences in the mineral recoveries were seen irrespective of whether amyl, secbutyl, isobutyl or isopropyl xanthates were used. However, when the concentration of xanthate was reduced to 10-4 M or in the absence of the copper sulphate activator, the effectiveness of the collectors was in the order: amyl > secbutyl > isobutyl > isopropyl > ethyl. Changes in the slurry pH appeared to have little effect on the recovery of the telluride mineral.Leaching tests of the precious metal telluride showed that both gold and silver dissolve in alkaline oxygenated cyanide solutions but at a much lower dissolution rate than metallic gold or silver. Both leaching tests and electrochemical measurements indicate that the dissolution rate of gold-silver telluride is controlled by the pH and cyanide concentration of the leachant.Roasting the gold-silver telluride materials in air at temperatures between 550 and 750°C resulted in its decomposition into a metallic gold-silver alloy and tellurium dioxide.

Jan 1, 1994

By E Wan, K Stokes

Since 1978, the nickel concentrator at Leinster has been subject to continuous change. In 1971 a significant nickel sulphide deposit was discovered on Leinster Downs Station, within three years the extent of the deposit was determined. In 1978 the Agnew Mining Company began production of nickel concentrate from the Perseverance Mine and continued to do so until production ceased in 1986. In 1988 WMC purchased the mothballed project and began the first phase of many expansion initiatives. Milestones in the life of Leinster have included:open cut mining of the Perseverance orebody and the discovery of the RockyÆs Reward orebody, as well as the metallurgical challenges in treating each of these; underground mining at both Perseverance and RockyÆs Reward; construction and commissioning of the WMC grinding and flotation circuits; variations in the reagent schemes, including the introduction of æliquidÆ reagents; development of mill linings to reduce maintenance; circuit re-configuration and simplification; development of Harmony open cut; strategies for increasing throughput at the drier; and changes to tailings facilities to cope with increased throughput. This paper outlines the steps which have been required to expand the Leinster Nickel Concentrator from 650 000 tpa to 2.5 Mtpa and those steps which will be required in the future.

Jan 1, 2000