Search Documents

The Olympic Dam Project constitutes a major resource of Copper and Uranium and has been under intensive evaluation since the discovery in 1975.A 500 metre deep rectangular shaft has been sunk into the deposit and this has been followed by 8400 metres of level, incline and decline development. 5 surface ventilation raises have also been constructed.Large scale trackless equipment is used to carry out the development, and productivity statistics are given.The paper describes the functionalised system used in the development program and discusses the maintenance support, and services required to carry out these works.The objectives of the Exploration Development program and the satisfactory results obtained from this work are also discussed.

Jan 1, 1985

By George CW

Western Mining Corporation (W.M.C.)operate a 30 000 tpa nickel refinery at Kwinana, W.A. using the Sherritt Gordon Process. Following ammonia/air leaching of sulphideminerals and subsequent copper removal, nickel metal is produced as powder by hydrogen red-uction of the ammonium sulphate-rich solution. Batchwise reduction in pressure autoclaves is preceded by an oxidation/hydrolysis step to ensure nickel powder quality.The reduction process is energy intensive, requiring high temperatures and pressures. Present energy requirement is 24 GJ per tonne of nickel reduced. Of this, 95% represents steam and hydrogen consumption and 5% electric power. The design and operation of the red-uction circuit is reviewed, outlining the main areas of steam and hydrogen usage.

Jan 1, 1985

By J Khosa, J Manuel

Iron ore sintering is very complex with many interdependent variables. For the same ores, the sinter quality and sintering performance may vary significantly with the scale at which the sintering tests are conducted. Therefore it is important to understand the effect of test scale on sintering performance and sinter quality while interpreting the test results. In this paper, different scales of iron ore sintering research at CSIRO are described and compared. This is followed by the results of two sinter blends tested at different scales. The results are compared and correlated to demonstrate the benefits of iron ore sintering research at the laboratory (4 g), small (5 - 8 kg) and pilot (55 - 140 kg) scales.

Jan 1, 2007

By Macaulay J

The recovery of gold from cyanide liquors is frequently effected by using activated carbon. Process economics however require non destructive methods of gold extraction from the carbon so that it may be recycled.Stripping at atmospheric pressure usingthe method of Zadra et al(l) suffers from the disadvantage of unfavourable kinetics with strip times of the order of 48-72 hours. Subsequent research has led to development of processes which strip the gold more rapidly namely: A.A.R.L. process, (2,3) organic solvent (4,5,6) and pressure stripping (7,8)This paper reports on a development of the pressure stripping technique in which stripping and electrowinning are carried out at elevated temperature and pressure.

Jan 1, 1984

By T D. H McGrath, R Byleveld, W P. Staunton, J J. Eksteen

"The Gold Technology Group at Curtin University through the AMIRA P420 series of projects has recently developed the integrated liberation leach model (ILLM) for optimisation of gold plants. The model encompasses recovery by both gravity (batch centrifugal concentrators or BCCs) and leach adsorption (CIP/CIL) circuits. The ILLM essentially combines the Group’s well-known standalone models (ie gravity and SIMCIL) to create a robust simulation package.The ILLM process model provides a tool for sites to determine optimum set points for operations to optimise recovery (eg target grind size). It can also be used to predict the effect on gravity recovery, leach recovery and overall recovery when changes are made to circuit design, either temporarily (eg a leach tank taken off-line for maintenance) or as part of a circuit expansion (eg expanded gravity circuit capacity, or addition of leach tank capacity).This paper discusses the capability of the ILLM process model by highlighting a recent case study. The paper also addresses the test work and plant data required as model inputs, as well as limitations and the application of the ILLM to greenfield projects.Citation:McGrath, T D H, Staunton, W P, Eksteen, J J and Byleveld, R, 2016. Application of an Integrated Liberation Leach Model for Process Optimisation, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 173–178 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

Underground excavations are subjected to complex stress changes caused by nearby mining, but may also be affected by repeated dynamic loading from blasting and seismic events. In some cases, the combined, cumulative effects can lead to unforeseen damage, displacement and instability. Simulating dynamic loading of an underground excavation is a very complex task. The state of rock mass stress, damage and deformation must first be simulated sufficiently requiring small-scale structures to be explicitly modelled. Supporting elements must be represented with high similitude and then the dynamic event must be applied to the system in the case of blasts, or evolve as a consequence of rock mass instability for seismic events. A special case is for the effect of pit blasting on underground excavations - discontinuous rock phenomena at scales from mine, to bench, to pillar, to tunnel need to be captured and this represents one of the most computationally intensive tasks in mine simulation. Recent advances in computer power allow these tasks to be completed at a mine scale, incorporating discontinuities and geological detail matching the best practice for static Finite Element analyses. The results are a worthwhile contribution to mine decision-making, but require careful interpretation and thoughtful inputs - even more so than quasi-static analysis - as the cumulative effects of unfavourable modeling practices are greater. Some learnings from experiences with mine scale, discontinuum dynamic simulation are summarised, including a discussion of considerations of scale and similitude for this type of analysis.

Nov 25, 2010

By S J. Henderson

Pumped co-disposal of coal processing waste was promoted in the 1990-2000s as a low-cost highperformance alternative to tailings dams. In particular it would avoid high up-front capital for rejects trucks and dam embankments, and would produce a combined waste deposit with better geotechnical properties than either coarse rejects or tailings. Overall, the promise was not delivered; in particular, upon discharge the waste segregated by size, and operators responded by moving the coarser waste to contain the finer waste. In consequence, not only did design analysis lag behind construction, but some of the initial expectations persisted with the result that analyses did not fully represent what was occurring on the ground. After more than twenty years inspecting, designing and tending Co-Disposal Areas (CDAs), it is apparent that they are essentially upstream constructed tailings dams with some more favourable aspects but also a few unique quirks. Although waste management technology has moved on somewhat, the high cost of changing CHPP waste circuits means that most mines with pumped codisposal will continue to discharge mixed waste slurry into CDAs. It is therefore worthwhile to share some lessons in the hope of promoting sounder design, operation and rehabilitation. These include: • Discharged waste does not form a homogeneous wholly competent deposit but instead comprises materials ranging from sandy gravel to silty clay with the distribution determined by movement of the discharge and decant structures; • CDAs circulate and contain a lot of water; • As a result of the first two points, some areas of the CDA comprise saturated fine waste that is no different from tailings and, like tailings, often behaves in an undrained manner; • Seepage is inevitable and desirable because strength improves as water is removed. However, stability is strongly impacted by pore pressures and in design these need to be rationally rather than optimistically considered; • As CDAs are built to about 40m or higher, strength-deformation characteristics of the foundation become more important; • Even if geomechanically stable, CDAs will need covers to prevent salts and acids from reaching the surface; and • Erosional stability of the cover material(s) will probably dictate maximum slopes for rehabilitation.

Jul 1, 2021

By R Lau

The fire safety design for road tunnels includes the following aspects: active systems, passive provisions and operational procedures. The active systems include the smoke control system, fire suppression system, detection system and fire fighter’s assistance systems. Passive provisions include escape passages, fire separation and fire resistance systems. The operational procedures refer to fire fighter access, reporting and alerts, evacuation processes and crowd control.Currently, these systems are typically designed by different designers or teams. These systems are intended to work together in a coordinated manner to provide the desired safety outcome. However, in practice, this is not always happening. The fire engineering process is supposed to bring together all these aspects and arrive at an integrated safety system. The fi re engineering process in practice is not integrating the design with the practice or reality and is thus arriving at less than desirably efficient safety systems.The example of design inputs shows how disconnected each system design basis is. The smoke control system design is based on the design fire size. The performance of the smoke control system is to achieve a smoke free environment for a defined space for a particular fire size – the design fire. The fire suppression system – most commonly sprinklers or deluge systems, is designed according to codes and to achieve a certain water discharge rate. The fire detection system is designed to detect temperature rise/rate of rise and perhaps density of smoke. Fire separation is determined to provide a certain period of service – mostly for structural elements. Escape route size and location is determined mostly by code compliance. Evacuation procedures are determined by Authority operational requirements rather than human behaviour.To arrive at an integrated fire safety system, the design basis and performances must be coordinated. An approach using fire scenarios would ensure all systems are designed to a common performance requirement. This paper will discuss how the current design approach outcomes compared with a fire scenario approach. More effective and efficient fire safety systems would require the stake holders to understand the implication of this approach and to embrace this through the fire engineering process.

Mar 8, 2011

Those developing or planning a new mining operation base their financial projections on amounts of gold produced as soon as practically possible. The choice and ongoing operation of mobile plant figures significantly in their projections. The implications of mobile plant selection are not always clear - until its too late.Our 'typical' gold mine would be a mine processing 800,000 tonnes of ore per annum, producing 37,000 ounces of gold with a life of mine of 10 years. Overburden layers are only evident in the first two years of operation.The pit will eventually, after some 5 years of mining, be some 300 metres deep, but confined to a mine radius of 2 kilometres.

Jan 1, 1986

I should like to congratulate Dr. Salamy on his most informative paper.Under the heading of "future development" Dr. Salamy states the intention of using 3 in. lifters. In this connection I should like to mention one or two of our findings at the Croesus Plant of North Kalgurli (1912) Limited. We have converted a 5i ft. x 11 ft. grate discharge ball mill to a high level overflow rod mill. When we were considering this conversion we explored the literature and decided on using 2t in. lifters on alternate liners-the results were not encouraging. The mill all but "took off" from its foundations,and performance with regard to tonnage was poor. There...

Jan 1, 1956

By Seedsman R

The fundamentals concepts of roof support are similar between coal mining, metal mining and tunnelling and yet there are different design approaches, different hardware, and different levels of site investigation. This should not be the case and this paper discusses the key geotechnical issues that should underlie all roof support design - the need to reinforce defects. A design method to build a beam in laminated rock under high horizontal stresses is presented. The method allows for changing rock strengths, defect properties and varying horizontal stresses. At one level the design can be implemented with design charts and tables. Lessons learnt during the implementation of the designs at 5 different mine sites are Discussed.

Jan 1, 1998

Throughout industry in Australia, time lost through work accidents and illness is three times greater than strikes. In 1978 in New South Wales alone, 400 workers died, 125,000 were injured, 6,000 were indust- rially deafened, and 3,800 people died of occupational cancer. It has been estimated that less than 10% of workers injured make claims for common law damages. The figure is probably in fact much lower than that. However, common law damages claims are starting to become a boom industry and employers are only now starting to see the effect of the increase in Claims. I predict that within 5 years the number of common law damages claims made will increase dramatically.

Jan 1, 1982

BHP Billiton Olympic Dam produces copper cathode, uranium oxide concentrate and refined gold and silver. The operation is comprised of an underground Mine and Processing Plant and is located 560 km north of Adelaide. Water for the operation is sourced from two wellfields located 120 and 200 km from the operation in the Great Artesian Basin (GAB) at a rate of approximately 36 ML/d. Regulatory drawdown limits were established to protect regional GAB springs and are monitored at compliance bores. Drawdown was predicted in the æOlympic Dam Environmental Impact StudyÆ (Kinhill, 1997); however, pumping at higher volumes may have the potential for increased drawdown resulting in a trend towards the compliance limits. In recent years increased usage of water in the Concentrator and Hydromet sections of the Processing Plant has caused excess process water reporting to the Tailings Retention System (TRS). This has resulted in excessive amounts of liquor ponding on the tailings cells with a potential impact being contamination due to seepage of liquor to groundwater. Effective management of water by the operation is necessary to both reduce GAB drawdown and reduce the amount of liquor on the tailings cells. A site working-group has been established to investigate and pursue opportunities to improve the water use efficiency of the operation. This paper will highlight the issue of water management at Olympic Dam and discuss the various options currently being investigated to improve management of this important resource.

Jan 1, 2006

By P Dowd, A Adeli, C Xu, X Emery

Geometallurgical modelling is increasingly being incorporated into mineral resource modelling and estimation as a means of increasing efficiency, decreasing operating costs and reducing risk in mining operations. Traditional geostatistical workflows for geometallurgical modelling face several difficulties, in particular, related to the non-additivity of process response variables, to highly heterotopic data sets and/or to preferential sampling designs, all of which may explain why most attempts to estimate geometallurgical response variables from assay data and mineralogy are still based on statistics and machine learning. The aim of the work presented here is to demonstrate the applicability of geostatistics to estimate copper recovery from copper sulfide ores at the Prominent Hill Iron Oxide Copper-Gold (IOCG) deposit in Australia. As recovery is non-additive, the preferred workflow is the joint estimation of the masses of metal in the feed and in the concentrate, both of which are additive variables. While the mass of metal in the feed can be estimated from abundant online assay analyses, the mass of metal in the concentrate can only be estimated from a very limited number of laboratory-scale batch flotation tests. Traditional approaches to estimating the masses of metal in the feed and in the concentrate, such as simple and ordinary co-kriging, are described and discussed. A modified version of co-kriging is introduced, which incorporates linear relationships between the mean values of the input variables, in addition to a spatial correlation model. Co-kriging with related means is shown to outperform traditional simple and ordinary co-kriging in terms of precision, accuracy and consistency of the estimates, and offers a practical and efficient tool to deal with highly heterotopic and preferential sampling designs.

May 24, 2023

By R J. Hardy

The aim of this study is to examine the volumetric and mass movement characteristics of load and haul operations using statistical modelling of relatively large samples of bucket loads that are transported as small samples in the form of truck payloads. Generally, the factors influencing bucket load variability are random, difficult to predict and to control. In the process of loading trucks the underlying variability of individual bucket loads will determine the variability of truck payloads. Bucket loads of material prepared by drilling and blasting for loading into trucks are fundamental quantities in open pit mine production. A study of payload data from a large surface mining operation indicates that bucket loads and truck payloads that are a small sample of bucket loads are normally distributed. Truck payloads have a reduced dispersion compared with bucket loads that is an inverse 0.5 power function of the number of passes per truck payload. Comparison of statistical modelling results with the æ10/10/20Æ policy promoted by Caterpillar Global Mining Inc, indicate that compliance with the æ10/10Æ part of the policy, applying to truck overloading is facilitated, as the coefficient of variation of truck payloads decreases, as a result of the increasing number of loading passes. Compliance with the more stringent æ20Æ part of the policy, relating to safe steering and braking is also facilitated, albeit at lower coefficient of variation for similar reasons.

Sep 26, 2011

By M Wortley, J McKay, D La Rosa, O Guyo

It has been a generally held concept that crushing operations were, by their nature, too simple to benefit from the implementation of advanced process control. The commissioning of an OCS¬ expert control system and image-based oversize detection system, VisioRock, at the Pilbara Iron Tom Price facility are dispelling these notions. A constraint-based OCS¬ expert control system has been designed and commissioned on the high-grade crushing and screening plant along with a vision-based oversize detection system functioning on six product conveyor belts. To date, the expert control has demonstrated the ability to increase production by maximising dynamic constraint utilisation. Dynamic constraint utilisation is a concept developed by Rio Tinto Technical Services for effectively evaluating constraint-based control logic performance. The VisioRock system has been installed and configured and has been operating for a period of several months. Currently, Tom Price and Metso personnel are working to define correct oversize detection thresholds. Details of the plant implementation are discussed.

Jan 1, 2006

By J-P Franzidis, M Esvelt, E V. Manla

The Floatability Characterisation Test Rig (FCTR) is a self-contained, highly instrumented, mobile pilot plant that is able to treat up to 2 tph solids. It consists of a bank of six 130 L WEMCO« SmartCells« and a bank of six 50 L WEMCO« SmartCells«. It was developed as part of the AMIRA P9 Project, primarily to determine ore floatability characteristics and to develop and validate flotation plant modelling, scale-up and simulation methodologies. However, it may also be used to carry out pilot-scale flotation test work. This paper briefly describes the circuit modelling, simulation and scale-up test work performed using the FCTR and the use of the FCTR in pilot-plant test work performed by the metallurgical staff at WMCÆs Kambalda Nickel Operations and Mount Keith Nickel Operation. At both Kambalda and Mount Keith the FCTR was found to be very flexible and straightforward to run, with an easily changeable circuit configuration and stable operation. Testwork was facilitated through having full stream sampling on all streams, and a high degree of instrumentation providing accurate measurement of process variables. The results obtained from the FCTR testwork were highly repeatable. As a consequence of using the FCTR, WMCÆs Kambalda Operation and Mt Keith Operation were able to complete a rigorous programme of pilot plant testwork more quickly than in the past, and with a high degree of confidence in the results.

Jan 1, 2003

By R Dimitrakopoulos, K Kawahata, L Montiel

A method that optimises mining complexes that are comprised of multiple processing destinations, open pits and underground operations is presented. Mining, blending, processing and transportation decision variables are simultaneously optimised while accounting for geological uncertainty. The method uses a simulated annealing algorithm at different decision levels to generate a stochastic-based extraction sequence and processing policies. A case study shows its ability to generate a higher net present value while facing a reduced amount of risk when compared to traditional optimisation methods.CITATION:Montiel, L, Dimitrakopoulos, R and Kawahata, K, 2014. Globally optimising open pit and underground mining operations under geological uncertainty, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 201–212 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By R J. Thompson

In truck-based hauling systems, the mine haul road network is a critical and vital component of the production process. As such, underperformance of a haul road will impact immediately on mine productivity and costs. Operations safety, productivity and equipment longevity are all dependent on well-designed, constructed and maintained haul roads. With the advent of autonomous haul trucks, the haul road itself becomes all the more critical to the success of these type of operations; not only in relation to mine operators requirements for safer and more efficient and predictable haulage systems, but also in response to autonomous truck manufacturers’ requirements for a more predictable and controlled operating environment. This paper presents a brief summary of the state-of-the-art in surface mine road design and then proceeds to examine the design and technological challenges associated providing a safe, predictable and affordable road for autonomous mine haul trucks. The paper serves as a basis for evaluating the contributions that enhancements in road design and management can deliver to autonomous mining operations, an initiative that also has scope for adoption within the operating life of many mines, haul roads and haul trucks.

Nov 22, 2011

The relationships between Aboriginal Traditional Owners and mining companies have often been mired in dispute, particularly since the High Court Mabo decision and the Native Title Act of 1993. In the Pilbara region, Rio Tinto Iron Ore (RTIO) impacts the traditional country of 12 Aboriginal Traditional Owner/language groups. Over the past 12 years the company and the Traditional Owners have negotiated and settled several significant land use agreements including the Yandi Land Use Agreement over the Yandicoogina mine in 1997, between Hamersley Iron (now Rio Tinto Iron Ore) and three language groups û the Bunjima, Nyapaili and Innawonga people and the Eastern Guruma Indigenous Land Use Agreement (ILUA) of 2006. These substantive agreements are now being followed by a new generation of region wide ILUAs which are close to conclusion. Arising from these regional agreements is a new framework for engagement which has been informed by the implementation of the previous agreements in the Pilbara and across the Rio Tinto group of companies. They are driven by both a company desire to have a consistent approach to engaging with Traditional Owners and the Traditional Owners wanting to have a similarly transparent and consistent standard of performance by the company in implementing the agreements which can deliver improved employment, cultural heritage engagement and direct and indirect benefits for the life of mining by the company. During the past three years the growth in the Pilbara, Western Australia brought new opportunities with people flocking to the region for employment flowing from the mining boom. Housing was at a premium and FIFO (fly-in, fly-out employment arrangements) was developed as a method to manage the general growth and demand for skills. Despite the recent down turn in the world economy since September 2008, which has reduced demand for minerals, the Pilbara continues to enjoy high levels of employment and as a result there is still significant pressure on housing and services provision. Although there has been vast economic growth in the Pilbara not only by mining companies but also oil and gas companies, the 2006 census data indicated that the direct benefits of improved employment, business development and engagement in the mainstream economy continued to exclude Aboriginal people. Indigenous people constitute a significant proportion of the population in the Pilbara region, some 6000 people û currently 14 per cent of the population rising to 18 per cent by 2015 û yet they remain at the bottom of the socioeconomic scale. More than 40 years of mining has returned relatively little to this group of people who are the permanent residents of the region and are connected through their traditional culture to this country (Taylor and Scambary, 2005). Ensuring local Aboriginal participation in the mainstream economy has been a challenge for resource companies, Traditional Owners and local residents in the Pilbara. The case study explores the relationship between a mining company û Rio Tinto Iron Ore and the Traditional Owners of the Pilbara. It examines two projects that have been developed to engage Indigenous people in the development of their region and through regional representation and business development to build a sustainable future for themselves and their future generations and at the same time ensure social cohesion to support social licence to operate. The case study also examines the process that was followed by Rio Tinto Iron Ore and its operations in undertaking a regional agreement for land access, participation and the integration of local Indigenous people into their business and the local economy.

Jan 1, 2009