Search Documents

By M Hopkins, A Mutale, A E. Vidal da Silva

The Cliffs Nickel Mine extracts a narrow near vertical nickel vein using a mining method of underhand bench stoping with paste backfill. In 2014, at a depth of 400 m below surface, the Northern block of the mine began to experience squeezing within ore development. At first the deformation was localised, within 30 m of the stoping front, but later became pervasive extending across the Northern block and resulting in a hiatus in mine production. The global mechanism is a progressive pillar failure, where the inter-level pillars in advance of the production front could no longer withstand the induced load and progressively yielded. The local mechanism of failure was observed as crushing of the massive sulphide ore and ‘punching’ of the pillars into the ultramafic hangingwall exhibited as floor and sidewall dilation and unravelling of the mafic footwall. The cause of the global mechanism was attributed to a combination of factors, including: high overall extraction ratio, small vertical pillar heights between ore development, high stress in relation to the low rock mass strength, shallow stope front angle, and insufficient ground support capacity. Following the progressive failure, the remnant rock mass conditions across the northern block were severely degraded, with numerous falls of ground that led to a reassessment of the mine plan. Recovery of the Northern block started in 2016 as a staged process. Development of the safe recovery work methodology involved a number of considerations, such as: production sequencing, development access design, ground support, and development of specific procedural controls. The Northern block was then broken into smaller mining precincts based on tactical factors such as location, ease of access, scale of rock mass damage and nickel content. A specific ground support standard and work methodology are employed, while cycle sheets are used to ensure quality and completeness of work. Large intersections showing signs of deformation have either been bypassed or treated using Rocprops to maintain stability during stope production. This approach has been successful in safely regaining access and restarting production in areas that had previously been removed from the mining reserve.

Mar 15, 2021

By D Smith

The Broken Hill deposit is located in Australia in the far western region of New South Wales. The deposit was found in 1883 and has been mined continuously since its discovery. It is considered the largest lead, zinc, silver deposit that has been discovered in the world and originally contained around 340 Mt of ore at a grade of around 12 per cent lead, ten per cent zinc and 150 g/t silver. The material remaining in the deposit represents only a fraction (perhaps ten per cent) of the original resource. Several of the world’s largest mining companies can trace their origins to the Broken Hill Field. The remaining resources on the CML7 consist of two large lower grade resource lodes that have not been subject to mining, some scattered areas of zinc lode material and the pillars and remnants of the main lead lodes.The deposit occurs in metamorphic rocks of the Broken Hill Group a division of the Willyama Super Group contained within the Curnamona Craton. The Broken Hill Group rocks have undergone multiple phases of deformation. Metamorphism is granulite grade with major shears cutting through the deposit having been retrogressed to mica schists. The deposit lies in an antiform associated with the second phase of deformation.The resultant proposed mine is situated on Consolidated Mining Lease 7 (CML 7) which occupies a strike length of 3.6 km in the central part of the 7.8 km long footprint of the orebody. Underground mining on CML7 ceased in 1975 with surface mining of silver chlorides in the weathered zone continuing until 1991. CBH Resources has been continually working to define and evaluate the remaining resource since 2002. This work has included four surface drilling programs, two underground drilling programs, an exploration decline, enormous amounts of compilation of historical data and detailed three- dimensional (3D) modelling of historical mining and the resource lodes. It is currently planned to commence production at the Rasp Mine in late 2011. The operations will produce from previously unmined lodes and from remnants and pillars.This paper primarily aims to encapsulate the processes involved from information acquisition through to resource estimation and also to highlight some of the challenges encountered and the specific techniques and practices used to overcome them. Many of the experiences at Broken Hill are applicable to all brown field sites.

Aug 22, 2011

By F Grobler

Many projects fail because project performance in unfavourable economic conditions was not anticipated at the investment decision stage. This type of failure may have been avoided through the selection of a strategy that enables the project to perform well under a range of possible future economic conditions (a ærobustÆ strategy); rather than an æoptimalÆ strategy for expected future conditions that will never eventuate. This paper describes a method of rapidly generating mine plans for a number of project strategies, and then evaluating it against a representative range of equally likely economic conditions. The key performance indicators derived for each strategy are the mean value and the distribution of values (variance). A prudent investor will identify prospective strategies not only on the merit of highest mean values (as a proxy for economic reward), but also on the probability of not meeting specified investment hurdles (a proxy for risk). A robust strategy will achieve its financial objective even under adverse economic variations. This paper focuses on the effect of commodity price uncertainty; particularly around the choice of mining and processing capacity levels. Results from enumerating 2000 prices scenarios against 63 strategy combinations show how processing and mining capacity can be manipulated to manage the risk-reward trade-off.

Sep 26, 2011

By C Donnelly

Redpath Australia is using a unique mining method for the Australian underground coal industry at Kestrel Mine Extension in the Bowen Basin, Central Queensland.The project involves completing two separate drifts from the surface for access to the German Creek Coal Seam located approximately 230 m below the existing surface. The scope of work is primarily the construction of two drifts; the first is 1577 m at 1 in 6 gradient and the second 1874 m at 1 in 8 gradient. Each drift has been developed by a Mitsui S200 roadheader with modifications to allow for a continuous tunnelling/mining cycle operation. A shotcrete boom has been fitted to the left hand side of the machine with the operators console located at ground level. Another operators console is elevated on the right hand side of the machine to allow operation of the rotary drill boom which is mounted on a slide rail to allow flexibility of positioning depending on the stage of the cycle. In support of the roadheader activities, an integrated conveyor system mounted on a sliding floor arrangement is able to be advanced as the mining face progresses. This sliding floor consists of four 1.5 m × 6 m sections that utilise hydraulic rams to ‘walk’ inbye, allowing room for installation of precast concrete floor panels for final floor completion. This method borrows from the tunnelling and construction industries to eliminate place-change delays in the mining cycle by enabling complete ground support installation without retreat of the primary development machine from the face. The aim is to reduce the project duration with the completion of final floor and services to within 30 m of the operating face as it advances.

Mar 21, 2011

By Ring R. J, Waters D. J, Vautier F. E, Fulton E. J

Laboratory leach tests have been carried out by the Australian Atomic Energy Commission to compare the effectiveness of Caro's acid (permonosulphuric acid) as an alternative oxidant to pyrolusite in the leaching of uranium ores. Results demonstrated that Caro's acid reduced acid consumption in leaching and the lime required for neutralisation of tailings liquor. The uranium extraction was unaffected by choice of oxidant.Following this study, Interox Chemicals Pty Ltd arranged a plant trial using Caro's acid at the Nabarlek uranium mill of Queensland Mines Ltd. The trial confirmed that significant savings in acid and lime usage can be achieved under plant conditions.Plant operations also demonstrated that Caro's acid has a number of significant operating advantages over pyrolusite.Queensland Mines Ltd have recently decided to convert their leaching process from pyrolusite to Caro's acid. The new system is expected to be fully operational by mid 1983.

Jan 1, 1983

By B Murphy, N Strong, J Albrecht

Rio Tinto’s Argyle Diamond Mine has a history of underperformance with delivery of ore from the underground operation to the surface for processing with no real clarity in sources of loss and value. In order to increase underground production performance, the basic concepts of the Theory of Constraints model were applied to the Argyle underground production system. This prompted a revised view on bottlenecks and contributors to value loss and ultimately leading to record breaking mine performance. System loss reporting to demonstrate the best opportunity to drive value, departmental detail to develop tools to identify improvement opportunities and clarity across the team to ensure alignment and clear lines of communication were critical to the project success.

Mar 15, 2021

By A Hosseinzadeh Barforoosh, A Abedi, M Taji

The effect of blast loads on beams is one of the main issues in the analysis of steel structure. In this study, experimental tests on steel beam under blast loading, and also numerical simulation by the Autodyn software to analyse these structures, is discussed. Experiments on steel beam size of 12 by Emulite4 explosive with 30 mm diameter and cortex is done. The patterns of cutting and bending generated in the two tests (empirical and simulation) show a good match.CITATION:Taji, M, Hosseinzadeh Barforoosh, A and Abedi, A, 2015. Comparison of experiment and simulation of blast loading on the steel beam, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 161–168 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By D Connelly

Magnetite ores can be used to produce very high-grade concentrates that are suitable feed for the direct reduction process route but the high sulfur content of some concentrates can cause substantial environmental issues. Processing of high sulfur magnetite ore is therefore increasingly problematic for the industry. Generally, the industry demands a concentrate with <0.05 per cent sulfur and <2 per cent silica. This paper reports the outcomes of a study to produce a concentrate with the requisite low sulfur content from a sulfur-rich magnetite ore. The main findings may be summarised as follows: if the sulfur is present in magnetite as nonmagnetic pyrrhotite or pyrite, it can be beneficiated using magnetic separation and hence, monoclinic pyrrhotite is magnetic and is magnetically recovered with magnetite leading to a concentrate that is too high in sulfur. X-ray diffraction and QEMSCAN analyses revealed that the magnetite concentrate was liberated at P80 30 microns and was associated with maghemite, pyrrhotite (magnetic), carbonates and hematite with very low amounts of chalcopyrite, sphalerite and arsenopyrite. Sulfur removal using flotation was the first stage of investigation and this required flash flotation in the grinding stage followed by column flotation of the initial concentrate to generate the final concentrate. At the same time, it was observed that oxidation of the pyrrhotite had a negative effect on its flotation requiring copper sulfate to activate it. Bioleaching and concentrate leaching were also considered and achieved over 90 per cent sulfur removal but were deemed unsuitable owing to the production of highly reactive wastes and high CAPEX. Reference is made to a number of operating magnetite producers and how they manage the sulfur in feed.

Sep 18, 2023

By T Wellman, G Sternadt, R Hingston

The 335 000 oz Wilber Deposit is located within the Meekatharra-Wydgee Archaean greenstone belt in the Murchison District of Western Australia. The deposit comprises high-grade gold mineralisation hosted within a steeply west-dipping quartz lode, which lies within a broader (20–60?m) north-east striking shear zone envelope. Locally, the northerly-trending host rock geology includes greenschist facies high-Mg basalt (albite, actinolite, chlorite, biotite, calcite, zoisite, muscovite and titanate) intruded by at least two generations of felsic to intermediate porphyries (albite, actinolite, zoisite, chlorite, sericite, biotite, quartz and titanate). The Archaean rocks are cross-cut by a number of east–west striking Proterozoic dolerite dykes (biotite (50 per cent), albite, carbonate, epidote, titanate and actinolite) that are interpreted to have intruded pre-existing regional structures. The entire mine package is cross-cut by a system of shallow north-east-striking, north-west-dipping, barren quartz veins that commonly contain large (up to 30 cm), euhedral, smokey quartz megacrysts.The north-east-trending lode lies within a 3 m wide shear zone and varies from a single discrete 0.5 to 4 m wide laminated, massive or brecciated quartz-carbonate vein to multiple laminated veins up to 1 m wide within the shear. The veins exhibit strong boudinage, with cross-cutting quartz-carbonate seal veins in the boudin necks. The boudin necks often contain pink calcite. The shear zone fabric wraps closely around the boudin necks proximal to the vein, becoming more lode parallel distal to the vein. The lode is offset by a north to north-north-west trending fault.Mineralisation occurs as free gold within the quartz carbonate veins, with accessory sulfides including pyrite ± chalcopyrite, ± galena ± sphalerite. Fuchsite is observed in the veins, as laminar wall rock inclusions, with visible gold commonly associated with the wall rock laminations.Gold grades range from less than 1 g/t within the hosting shear zone, either at the margins or interstitial to the veins, to approximately 30 g/t in the single vein, and up to greater than 60 g/t in the multiple vein areas. Gold is commonly visible and disseminated throughout laminated, breccia and massive quartz veins, although laminations show the highest concentration of gold grains.CITATION:Hingston, R, Wellman, T and Sternadt, G, 2014. The geology of the Wilber Deposit, Andy Well Gold Project, Murchison District, Western Australia, in Proceedings Ninth International Mining Geology Conference 2014 , pp 55–64 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By M E. Karmis

Traditional coal mining planning seldom considers key æsustainability factorsÆ such as: societal impacts in the area; jobs (both created and lost); dislocation of towns and residences; impact on neighbouring communities and individuals; infrastructure concerns; post-mining land use (except when limited by law or other factors); habitat disruption and reconstruction; long-term economic impacts in the community; and net long-term community benefit. This paper presents a systems engineering approach based on the premise that systems can only be optimised if all factors are considered at one time. In theory, coal mine designs can be optimised for return on investment, environmental protection and sustainability. Using this approach, the permitting process may be quicker and less costly, relationships with neighbours, communities, environmental groups may be improved, the mining industry may be seen as a positive for the short-term and long-term and the mining industry may increase profits. This paper discusses geographic information system (GIS) tools that may be used to incorporate ecological and other sustainable development concerns into models of coal mine sustainability performance. Along with coal production cost and value information obtained from past and present coal mining operations, GIS data are used to develop mathematical cost and equation models. By analysis of on-the-ground data, the parameters to be included in these models are identified, the relationships between these parameters quantified and the models developed. The paper also discusses the next phases of the work to be completed once the data is obtained and the models are adjusted and validated. At that time, site-specific information will be input into the models and the approach to mining a particular property evaluated and optimised for financial rate-of-return and other desired outcomes, such as preservation or enhancement of sustainability values. Finally, the paper will examine how this approach can be combined with traditional mining engineering considerations in order to develop an optimised mine plan for a specific mining property.

Jan 1, 2009

By Z-Y Pi, B Zhang, S Wen

"The paper introduces the structure and work processes of outside auger hollow claw tipped mechanical sampler for coal. Twenty sets of claw tipped sampler performance tests show that: The design of inner hollow cylinder-type (?180 mm) can ensure to take a coal sample with nominal top size of 60 mm. Built-in self-cleaning piston pusher ensures no adherence and blocking of the sample. The operation practices show that the mechanical sampler can operate in order for taking coal sample with up to 16 per cent of total moisture. Claw closing design can avoid sample leaking or spilling during the claw lifting and ensure the integrity of primary increment. Ultrasonic positioning device makes the sampler capture the materials no less than 10 cm from the bottom of the wagons, basically meeting the requirement taking full depth of the sample. The precision and bias test indicates that the moisture and ash have no relative bias under the sampling process; the sampling precision is in accordance with the requirement in IS013909.At present, the spiral mechanical sampler is widely used for coal sampling but there are many limitations during application, for example: It is difficult to capture a large size sample, so the size range of a coal sample taken is limited. There is easy adhering or blocking for high moisture coal, which will result in the mixture of different increments, wear of sampler and the difficulties for cleaning and maintenance of sampler. It is difficult to capture the coal sample at lower than 30 cm from the bottom of the wagons, in order to avoid damage of the vehicle. It is possible for coal sample loss and spilling during the sampler lifting, due to the unsealed sampler.For the outside auger hollow claw tipped mechanical sampler designed for solving the above problems, the opening distance of the claw is the opening size of the sampler and makes the size range of the coal sample to be taken wide. During sampling, the two pieces of claws open and the sampler rotates vertically downward to capture an adequate coal sample after reaching the specific point. Then the two pieces of claws close tight automatically to ensure there is no coal leaking or spilling. The inner pusher of the sampler will prevent from the adherence and blocking of the coal sample effectively.CITATION:Zhang, B, Pi, Z-Y and Wen, S, 2012. Outside auger hollow claw tipped mechanical sampler for coal, in Proceedings Sampling 2012, pp 41-44 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 21, 2012

By K Gardner, R Fraval, V Singh

Using new technology to create optimised infill drill programs in underground or open pit settings, it is possible to quantify the value of a drill program. The computer designed programs are optimised to uplift the most amount of resource possible into the specified resource classification, while honouring geological, spatial, equipment and budgetary constraints. When designing ‘by hand’ balancing all these factors is a time-consuming effort with no real way to determine metrics on ‘how good’ a program will be. The optimisation considers many factors allowing geologists to apply critical thinking and domain knowledge to constrain the optimisation, letting the computer do the heavy lifting of determining hole placement. Once programs have been created, they can be integrated into a production schedule. This is a critical step in determining the correct sequencing and balancing of resource availability and seeing how a program will interoperate with other tasks in the mine. For example, if drill drives are a requirement for part of the program, will they be developed in a time frame that is useful for the goals of the program? Do we risk drilling infill holes too late to add value? Do we put production at risk by not classifying parts of the model ahead of time, thus adding to uncertainty? Using software to assist with optimising and scheduling of drilling is a useful technique to save the geologists from the mundanity of manually designing drill programs and puts metrics around the effectiveness of a program and has the potential to add quantifiable value to a program. Examples will be presented that demonstrate the effective use of drill hole optimisation, comparing manual designs with optimised designs, as well as the examples that show the effective use of scheduling.

Mar 22, 2022

By C E. Woolley, H Jebaliya, J Foster

The East wall of the Kalgoorlie Consolidated Gold Mines Fimiston Open Pit (KCGM Superpit) has a history of wall instabilities impacting mining operations; the most significant of which occurred in May 2018, when more than 1 Mt of rock dislodged over six, 30 m high bench stacks and impacted the pit floor. Since 2011 approximately 1.250 Mt of material has fallen from the East wall at Fimiston Pit across three failure events (2011, 2018 and 2020). Each failure has been associated with major structures intersecting the pit walls: the Fiji Fault, the Australia East Secondary Splay Fault and the EWD3 Fault. In each instance the trigger for failure has been transient pore pressure in the pit walls. Northern Star will mine a cut back behind the failure area over a vertical distance of 180 m. Cut back mining will include the extraction of a remaining in situ wedge, which is assessed as kinematically able to fail, and a subvertical failure backscarp in Stage 1. A substantial amount of rill material from the 2018 and 2020 failures will be extracted in Stage 2. This paper presents the methodology in use to mine Stage 1 of the cut back, safely, through this potentially high-risk area, detailing the specific mining methodology employed, the controls put in place and the monitoring required. Day-to-day monitoring will be undertaken using the already installed slope stability radar and will feed into a daily assessment of activities which may be undertaken in the cut back area. Initial activities will focus on eliminating the potentially unstable wedge and vertical backscarp with use of innovative drill and blast techniques/products and the extensive use of remote capable equipment to limit personnel exposure.

Jun 22, 2022

By J P. Sykes, C Gemell, A Trench

The perceived and actual impact of government mineral policy upon the government share from gold mining revenues is assessed for ten key countries in which the gold sector is of relevance in advancing economic growth. Five African and five South American jurisdictions are considered, namely Burkina Faso, Ghana, Mali, South Africa and Tanzania from Africa; and Brazil, Chile, Colombia, Guyana and Peru in South America.Both the headline corporate income tax rate and royalty level are identified as poor indicators for the total government share. In addition, significant differences between industry perception and actual government tax levels are identified by this study. The quantitative financial analysis shows that there is no clear relationship between individual taxation rates, taken in isolation, and the overall average effective tax rate (AETR) paid by the project over its life. Neither companies nor governments should use individual taxation rates, or industry perceptions, in isolation to assess the overall competitiveness or equity of a country’s minerals taxation regime – such analysis can be very misleading.In this study, the perceived impact is determined from the well-established Fraser Institute survey published each year, and in 2014 compared 122 minerals jurisdictions globally. The actual impact is determined from quantitative modelling of the financial performance of a hypothetical gold mining project in each country. The technical parameters of the project are held constant; instead the differing mineral policies in each jurisdiction are applied to determine the resultant impact upon the relative share of the economic rents delivered to both private and public sectors. In the quantitative analysis, the total government share varies from 36.3 per cent in South Africa to 66.5 per cent in Ghana.CITATION:Gemell, C, Sykes, J P and Trench, A, 2016. Is perception reality? Evaluating the fiscal attractiveness of international jurisdictions for gold mining investment, in Proceedings International Mine Management Conference, pp 227-238 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By E Asakpo, S Chaffer, A Heath

Newmont has had continuous production at their Ahafo operations, Ghana, since 2006. In 2013, Ahafo initiated an efficiency programme to improve mill performance and reduce energy consumption. Following this assessment, a Turbo Pulp Lifter (TPLTM) was installed in the Ahafo SAG mill in April 2015 to replace the existing radial pulp lifters. Plant operational data showed delivery of a power saving of 10 per cent, an improvement in throughput of 3.3 per cent, with no loss of grind size. Pulp lifter life was also doubled from 11 to 22 months.However, during subsequent relines when the grates were removed it was found that one in four of the outer pulp lifters were wearing at a faster rate than the remainder. This was investigated by Discrete Element Method (DEM) modelling, which predicted some overtopping and internal recycle within the pulp lifter. Significantly, the model predicted that the recycled material would pass back down every fourth outer pulp lifter, matching the field observations. Subsequently, the DEM investigation was continued and became an R&amp;D project to improve the TPL design. The results are summarised here, leading to the development of the next generation Spiral TPLTM.CITATION:Heath, A, Chaffer, S and Asakpo, E, 2018. The development of optimised pulp lifter design for the Ahafo SAG mill using discrete element method modelling, in Proceedings 14th AusIMM Mill Operators&#39; Conference 2018, pp 585–594 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By M Wagner, H Assimi, F Neumann, C Garcia, B Koch

Run-of-Mine (ROM) stockpiles are the inventory of valuable materials extracted from the mine. Depending on the customer requests, a selective addition of ore from stockyards should be selected at the required tonnage. In the stockyard, stackers and reclaimers are the machines which load and unload ore, respectively. Currently, humans determine the reclaiming/stacking planning sequence in the stockyard by rules of thumb. However, this is a complex task subject to multiple operational constraints, such as where undesirable mineral properties should not exceed certain limits in a request. Human planning can lead to limited decision support and lower ability to consider the upcoming blends and requests. This kind of decision making can cause perturbations in the assumed profit and unexpected loss in practice. Therefore, an intelligent decision-maker and sequence planner would be highly valuable to automate stacking and reclaiming operations in practice. The benefits are reducing variability in decision-making and operation costs. This paper considers a stockyard with available mineral information in the stockpiles using load and dump locations from GPS data feeds. We present an optimisation problem to find a solution which results in reclaiming more ore in a shorter time. To solve the problem, we develop an automatic search strategy based on the greedy search algorithm independent of the type of machine used in reclaiming. The proposed method plans a sequence for stockyard recovery blend optimisation to meet multiple customer demands in a timeframe. Blend optimisation is subject to various constraints such as the elemental composition of the valuable materials and penalty elements. We present three case studies using EKA’s simulator, to fulfil two to four requests from four stockpiles. We compare the obtained results with a pilgrim step reclaiming heuristic and we show how our proposed search strategy outperforms the current strategy used in practice.

Nov 10, 2020

By D Phillpotts, S M. Mantsho, P Strobos

A challenge on many industrial flotation circuits is controlling concentrate mineral grades using measurements that are provided infrequently. The mineral grades in concentrate streams are a critical performance indicator in any industrial flotation circuit. Failure to achieve concentrate mineral grade targets has significant financial consequences on a flotation operation. A violation of a gangue mineral grade limits by the concentrator may also result in significant penalties. Online grade analysers which can provide reliable real-time grade measurements are essential for effective grade optimisation. The Blue Cube MQi analyser (by Blue Cube Systems) has recently come to prominence for its ability to rapidly determine mineral concentrate grades online and in-stream. This has provided excellent insight into the actual process dynamics in the flotation circuit, and hence enabled real-time control and optimisation of concentrate mineral grades. MintekÆs Measurement and Control division, specialising in advanced control solutions for mineral and metallurgical industries, has had the opportunity to link the FloatStar Grade-Recovery Optimiser to the measurements provided by the Blue Cube system at a nickel concentrator plant. The project initially focused on stabilising the final concentrate grade without directly accounting for nickel recovery. The site later procured additional Blue Cube MQi analysers, resulting in the expansion of the FloatStar Grade-Recovery Optimiser to incorporate recovery component in the performance. This site already had the FloatStar Grade-Recovery Optimiser for several years, but the original grade measurement device was unreliable and ultimately failed. The system was reactivated once the Blue Cube system was installed, replacing the old analyser.CITATION:Mantsho, S M, Phillpotts, D and Strobos, P, 2012. The implementation of FloatStar grade-recovery optimisation control solutions using Blue Cube online grade analysers on industrial flotation circuits, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 363-368 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By B Roache, A Vakili, R Talebi

When a highly anisotropic or weak rock mass is subjected to high-stress conditions, it can lead to large ongoing deformations or squeezing ground conditions. Squeezing ground conditions can impose increased support costs, delays associated with rehabilitation, and disruption to production schedules. Ultimately, in more severe cases, it may result in complete drive closure. Several recent case studies investigated the squeezing mechanism and measures to control squeezing ground in underground mines and also to design appropriate ground support systems. Effective management of squeezing ground conditions requires a sound understanding of the failure mechanism and the driving forces. Once the failure mechanism is understood, the appropriate ground support system should be tailored to specifically manage the critical driving forces that control the squeezing mechanism. Support type, support stiffness, reinforcement length, support density, installation times and mining sequence all have important impact on the effectiveness of the support system. This paper provides a case study at the Ballarat Gold Mine in Australia, where drive squeezing was associated with foliated ground conditions located below 700 m depth. Numerical modelling was used to better understand the failure mechanism and the driving forces that lead to squeezing conditions. The effectiveness of various support types was compared to installed ground support performance. This has provided a credible methodology for assessing and optimising the selection of reinforcement in squeezing ground conditions. CITATION:Talebi, R, Roache, B and Vakili, A, 2018. Understanding and modelling squeezing ground conditions at the Ballarat Gold Mine, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 107–118 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By D David

The development of Western Australian magnetite deposits has lead to the design of some of the largest grinding mills and plants in the world. One of the projects demonstrates the efficiency gains possible by developing a simple yet thorough test program for circuit design. By drawing on the experience of current magnetite operations in Australia and the Mesabi and Marquette iron ranges in the United States, a basic flowsheet was developed. Through comprehensive testwork with AG, ball and stirred milling the flowsheet was optimized to take full advantage of each grinding mill’s strengths to reach the required final grind size. Laboratory work was verified in the pilot plant to optimize the energy efficiency of each grinding step while ensuring adequate liberation at each step for sufficient gangue rejection. By using three stages of grinding, the ball mill can best be employed in ensuring all top size gangue material is liberated and removed in the second magnetic separation step. The inclusion of the IsaMill, with its inherent steep product size distribution, as the tertiary grinding stage ensured that maximum grade was achieved and simplified the downstream process while giving further improvements in total grinding capital and operating costs. In this way the combination of the two technologies downstream from the AG mill is far more efficient than either would be on its own by reducing the total installed power by 1/3 and annual grinding media cost by 2/3.

Aug 8, 2011

By L Scheunis, A Van den Bulck, E Jak, K Verbeken, M Shevchenko, R Starykh, I Bellemans, P-J Boeykens

As a result of the globally increasing consumer use of electronic devices, it is expected that pressure will increase on the supply chain of precious metals. Hence, recycling of these electronics becomes increasingly important, as well as optimising the current processes. One major issue in metallurgical processes is the amount of metal that is lost into the slag. This metal loss is inherent to the production process and therefore, additional processing steps such as slag cleaning may be required. Slag cleaning can be done in electrical resistance furnaces where heat is produced using the Joule effect, making the slag’s electrical conductivity an important operating parameter. Since slags are ionic liquids, the electrical conduction happens via the movement of ions which is called ionic conductivity. However, within the presence of transition metal oxides, a second mechanism of conductivity occurs as electrons are able to hop from one transition state to another, which is known as electronic conductivity. As ‘FeO’ is a common slag component in the non-ferrous pyrometallurgical industry, both mechanisms are present, but their proportions vary with the respective amounts of the two forms of the multi-valent ions and hence, with the oxygen partial pressure. The goal of the present study is to develop an experimental set-up and methodology for measuring the electrical conductivity of synthetic SiO2 – CaO – AlO1.5 – ‘FeO’ slags at various oxygen partial pressures.

Jun 19, 2024