Search Documents

By Alford R. A

The causes of the loss of heavy mineral from mineral sands wet concentrators were identified through detailed surveys of two such concentrators. It was found that tray and spiral sluices preferentially lost elongated panicles, but panicle size had little effect on loss. Recovery was shown to increase with panicle density. The major influences on the recovery efficiency of individual concentrating devices (stans) were feed rate and feed grade, recovery increasing with decreased feed rate and with increased grade. Uneven distribution of total solids and heavy mineral to individual stans contributed to losses through the corresponding effects in feed tonnage and grade. Computer simulation demonstrated that significant recovery improvements could be obtained by appropriate adjustment of splitters to optimise the characteristics of internal plant flows.

Jan 1, 1991

By Muir D. M

Highly saline process water has a number of implications for the CIP process during the leaching, adsorption and recovery of gold. The reduced oxygen solubility in saline water can seriously reduce the rate of gold leaching, while dissolved oxygen meters do not necessarily reveal actual oxygen concentrations in saline water. High levels of magnesium in the ground water necessitate operation at lower pH (-9), with the potential for greater cyanide loss via HCN stripping. In addition increasing salinity renders viscosity modifiers largely ineffective.The adsorption capacity of aurocyanide onto activated carbon is improved with increasing salinity, but misleading results can be obtained in assessment of gold loading kinetics of plant carbon samples already loaded, or partially loaded, in saline water if subsequently tested in fresh water. Elevated chloride levels in the Zadra elution process can cause severe anode corrosion in the elecuowinning cell. The Anglo elution process is tolerant to only slight increases in water salinity, but elution times can be reduced by ethanol addition. Care is required in carbon regeneration, as salts can catalyse carbon decomposition as well as increase kiln corrosion.

Jan 1, 1994

BHP BillitonÆs Yandi channel iron deposit has a large resource of approximately 1.3 billion tonnes. This is a bulk mining operation with a high degree of selectivity not being practical. In contrast the deposit geology is a complex interrelationship of primary channel facies, secondary enrichment of iron and a secondary redistribution of the major contaminants. These variations in geology and alteration can occur over ranges of hundreds of metres down to knife edge contacts. In addition, differences in primary facies and mobility during alteration often result in the iron and contaminants having different patterns of enrichment and depletion. Despite the scale of these operations, if the geological domaining is not optimal, significant errors in the resource estimate of grades and tonnage will occur. Getting the geology right has become a common clichT among mining professionals. However, in many situations, obtaining optimal geological domains for resource modelling is best achieved when there is input from geology, statistics and geostatistics. In this paper, moving window statistics are utilised to see through locally high variability to identify trends that assist in locating difficult to identify geological boundaries. After the creation of geological domains, univariate and multivariate statistics and principal component analysis assist in validating and characterising geological domains. Finally, variography and domain contact analysis are used to analyse the nature of the boundaries between geological domains. At the Yandi channel iron deposit, the inter-relationship between geological and geostatistical analysis has resulted in significant improvements to geological domaining and the treatment of domain boundaries during estimation of iron and contaminates.

Jan 1, 2005

How many of you have felt tired and light-headed after standing or working in the sun or by the oppressive, hot, muggy conditions of an Australian summer? For those of you who have, you've experienced the minor effects of heat stress. Heat

Jan 1, 1994

This case study describes various aspects of establishing a laboratory facility for testing chemically-cemented fill materials. The applicability of data obtained from such a facility related to mine conditions depends on many factors: kind of data, type of testing facility, sample parameters (composition, geometry, size, etc.). The equipment employed must be adaptable, to accommodate variations in sample size and properties. The design, construction and operation of the testing facility is described, and its application to fill samples prepared from sulphides and oxides both chemically and naturally cemented. The present system was selected following an extensive study of equipment available for testing materials in the fields of rock mechanics and construction materials. The strength testing' facility incorporates Linear Variable Differential Transformers for monitoring both lateral and axial displacements during sample compression. The output from these and from other related instrumentation can be recorded or fed direct to a computer, enabling stress-strain data to be printed out while the test is in progress. Also described are controlled environment curing facilities which allow samples to be cured or weathered under different temperature or humidity conditions to simulate long-term ageing and in place conditions.

Jan 1, 1973

By Sobek S, Lotzien RM

Although the conventional procedures for designing agitator flotation plants are well-known and reliable, little experience for designing modem pneumatic flotation plants has been gained up to now. A reliable procedure originating from graphic methods for the design of distillation columns is presented. Examples demonstrate on laboratory and semi-technical scale the application of this extremely practical method for designing a fly ash and a magnesite flotation plant.

Jan 1, 1993

By Abraham B. K, Jensen B, Gillies A. D S

The aim of the research was to investigate the feasibility of using an impedance cell and ratio-transformer bridge to measure solids content in coal slurry pipelines. It appeared that this technique could be developed to measure variations in conductance which correlate with solids content. Successful implementation of the measurement technique would have a variety of applications in existing coal wash plants and the potential for automatic process control. A small pilot plant was designed for a feasibility study. This was a closed loop system in which the coal was uniformly dispersed in a tank with a variable speed agitator and then circulated through an external pipe returning to the top of the tank. The impedance cell was located near the end of the external pipe. Slurry concentrations were varied from clean tap water to 50 per cent solids by weight with the addition of weighed quantities of dry coal dust. Ratio-transformer bridge measurements showed that variations in individual observations were equivalent to measurement errors of about two per cent. These probably reflect variations in concentration of the mixture in the pipe. Data for increments in concentration of one per cent indicate that this is about the limit of resolution of the current system. The paper discusses the principles of operation of the impedance cell and measurement system. Results from the pilot study and proposed improvements in the impedance cell design are examined.

Jan 1, 1995

By Grieveson P, Rajakumar V

The reduction of an ilmenite concentrate with coal at 1000, 1050 and 1100¦C was investigated using thermogravimetry and X-ray diffraction, optical microscopy and electron probe microanalysis of the product. The effects of temperature, coal particle size, addition of ferric chloride and preheating of the concentrate in argon on the reduction kinetics and mechanism were determined. The rate of reduction increased significantly with temperature and was enhanced by the addition of the catalyst. The morphology of the iron was primarily determined by the degree of weathering of the particle. Significant coarsening of iron was obtained in the dense particles by the addition of ferric chloride. The sequence of reduction and the enhancement in the rate of reduction by preheating the concentrate in an inert atmosphere are discussed.

Jan 1, 1991

By Ooms M, Scott OJ

This paper is concerned with the design and operation of storage and discharge facilit- ies for bulk solids handling. It presents an overview of the basic design philisophy emphas- ising the influence of bulk solid flow propert- ies and bin geometry on the flow patterns developed and how these, in turn, affect the reclaim efficiency and the bin structural in- tegrity and wear characteristics of both bins and chutes. The salient aspects of feeder design and operation will be discussed and the need to consider feeders as integral parts of the bin discharge system will be stressed.

Jan 1, 1978

By Postupack C

A major problem that has continued to plague the surface and underground coal industries is blast induced damage to the coal seam. Blasting Analysis International, in conjunction with a number of other organizations, has continued to address this concern through 14 years of field research in 68 full-scale production environments worldwide. Compiled results were obtained from varying field conditions. These included single and multiple seam coal mines, horizontal, rolling and steeply dipping coal seams and varied borehole diameters (ranging from 102 to 381 mm) and when using various explosive formulations. Results are discussed in detail along with the tools, test methods and analysis techniques to identify and quantify the problems. Over ten major causes of coal damage were identified. A number of practical and economic recommendations are presented that can benefit the entire coal and blasting industry especially in commercial operations whose economic growth relies heavily upon recovering an undamaged coal seam.

Jan 1, 1995

By N Strong

Cracow is a high-grade; low-tonnage underground gold mine located approximately 500 km north-west of Brisbane in Central Queensland. It is a steeply dipping, narrow vein, epithermal gold and silver deposit that is accessed via a decline from surface. Cracow is owned by joint venture between Newcrest Mining (70 per cent) and Sedimentary Holdings (30 per cent). The orebodies are 5 m wide on average and the ore is extracted via sublevel open bench stoping. Stopes are extracted to a strike of approximately 25 m before being backfilled with waste. Prior to the introduction of electronics, the mine would remove a small amount of the previous backfill out to create a void, and then begin blasting two to three rings at a time, with the ore being extracted between each blast. This method caused the ore to be blasted onto the waste backfill resulting in dilution of the high-grade ore. It also meant that the extraction of each stope took a number of weeks and numerous blasting events. In the fourth quarter of 2005, the mine struck a geotechnically sensitive stope, where all 20 rings had to be extracted in a single shot or risk possible geotechnical problems that could sterilise the ore. Due to the limitations of NONEL« delay detonators the mine could not fire all the rings in a single shot and needed to use an electronic detonator system to extract the stope. Some unexpected benefits to the mine were increased fragmentation, reduced vibrations, reduced dilution, improved efficiency and improved hanging wall and footwall conditions. After the success of this first electronic shot, the mine has since moved to firing all their stopes with electronic detonators. With electronics the mine has been able to fire much larger blasts, and has in fact moved to firing their blasts in the opposite direction, firing towards the draw point instead of into the waste backfill, thus reducing ore dilution.

Jan 1, 2008

By Hunter T. C

The wirebar furnacing and casting facility commissioned in 1970 at Copper Refineries Pty. Ltd. (CRL), Townsville, comprising a 70 tonne/ hour ASARCO shaft furnace and a Walker type casting wheel, contained several unique design features. Since commissioning, effort has been directed at improving metallurgical control of the casting process. This has resulted in the identification of optimum mould lubricant properties and the use of continuous on-line measurement of molten metal oxygen content. Casting defects such as cracks and surface porosity are readily explained and controlled using these techniques.

Jan 1, 1977

By Wasserman A. D

Methodological approaches and in- vestigation results are considered in the paper of heatmass transfer processes when harmful impurities are scattered and remo- ved from chamber-like workings, of the air distribution in complicated ventilation sys- tems and of chemical conversion of exha- ust gases in mine atmosphere when diesel equipment is operating. The results presented in the paper are the base for creation of the automatic design, control and regulation of the venti- lation processes.

Jan 1, 1988

By Sullivan BJK

The 1100 orebody is a massive copper sul- phide orebody which contains a major portion of the Isa Mine copper ore reserves of 130 million tonnes at 3.2%. The underground mining of a deposit as large as the 1100 orebody is technologically a complex operation as extraction strategies have to be evaluated with reference to 1. rock mechanics considerations, 2. safety and environmental standards, 3. production and operating require- ments and 4. metal recovery and costs. The mining philosophy in the orebody has undergone considerable change over the past five years as a result of experience and improved technology. At this stage, primary stopes are extracted by high rise sublevel open stoping and pillars by slot and mass blast drawn either under rock fill or as an open Stope.

Jan 1, 1978

By Jensen W. S

The Mount Morgan ore-body is intersected by dykes to such an extent that it presents peculiarly difficult problems in extracting ore. These are shown on Plates Nos. LXVII. and LXVIII. Besides ,these dykes there are innumerable "heads," which alsoare a source of danger. Falls of ore occurred in the end of the year 1908, resulting in serious loss of life to miners employed. It was decided, after an exhaustive inquiry, to change the entire system of mining from the" flat backed stope system" to the" square set sectional system ," the latter being more flexible and allowing bad ground to be cut out from a safe position; but it became evident that, whatever system was adopted, there would be more or less danger unless all the dykesand heads known were picked up, and their continuation plotted on a special set of plans on which the general scheme of stoping could be plotted from time to time as work progressed. It is worth while pointing out that, in every other branch of engineering, it is usual to design the work, and that only in mining engineering has it been common to do the work first and plot it down afterwards.The term "sectional analysis" is familiar in most branches of engineering design, and as applied in this paper to mining, may not bear the same meaning, but the general purpose is analagous, and there is no other term used.

Jan 1, 1911

By S Arthur, J Mills, A R. Penney

A key aspect of seismic management for narrow vein stoping of the west zone at the Beaconsfield Gold Mine has been the development of a fully remote extraction method that does not require personnel access to sill drives within the orebody once stoping commences. Initially, sill driving within the reef is undertaken in a conventional fashion under geological control. Sill drives are developed at a vertical backs-to-floor height ranging from 7 - 12 m. This mining stage includes all activities prior to the commencement of stoping, after which no personnel enter the unstoped section of the sill drive at any time for any purpose. The key aspect of the remote mining cycle is the use of footwall drill drives paralleling the ore drive at a minimum separation of 6 m under survey control. These drives provide the platform for fan drilling of the orebody. Up to 20 m strike panels are blasted in a single shot using electronic blasting techniques. Ore is mucked from the extraction level sill drive using tele-remote loaders. Aerials for tele-remote operation are installed through boreholes from the footwall drive, negating the need for personnel access to the sill drive. Once mucking of a stoping panel is complete, a laser scanning survey instrument is used to survey the final void for subsequent design and production reconciliation purposes. The survey instrument is mounted in the bucket of the tele-remote loader, and is also operated remotely. Finally, tele-remote loaders are used to dump waste rock fill from the upper sill drive. A system of flags and cameras installed in boreholes from the footwall drive assists the operator in locating the live stope edge during the filling cycle, again negating the need for personnel access.

Jan 1, 2008

The proximity of the Town of Kalgoorlie to the Mount Charlotte mine necessitates that charge weight per delay be limited in order to keep surface vibration levels within acceptable limits and to reduce damage to underground workings. The mining system requires that large mass blasts must be used to recover pillars and therefore a large number of separate delays are needed. Until recently all blasting has been done electrically, fired from mains, but with the introduction of large diameter blastholes (165mm diameter) this firing system was inadequate. Various firing systems were considered, but after extensive trials a non-electric sequential firing system was chosen. This system fulfilled all criteria of blast design, was relatively straight forward in charging technique and had a very simple primary initiation system. Although initially designed for large mass blasts, the non-electric firing system is now used for all large hole blasting and in a simpler form for small (57mn diameter) holes.

Jan 1, 1982

The iron ore mining operations carried out by Goldsworthy Mining Limited at Golds- worthy, Shay Gap and Sunrise Hill, in the Pilbara region of the North-West of Western Australia, are unusual insofar as the ore reserves occur in a number of widely separated and relatively small deposits, requiring deep mining below the water table, and even below sea level at the Goldsworthy pit. This paper has been prepared to describe some of the problems associated with these deep open cut mines, and the technology employed to overcome them, in order to provide an efficient and economical operation. The problems discussed are: 1. Development of the Dewatering System for the Goldsworthy Mine. 2. The Stability of Pit Slopes at the Goldsworthy and Shay Gap Mines. 3. Development of Diesel Electric Trucks for Lonq Uphill Hauls.

Jan 1, 1979

By Dharmappa HB, Sivakumar M

This paper is concerned with two case histories of wastewater quality management in underground coal mines in the Illawarra region. The first investigation briefly presents an analysis of mine water discharge having an extremely high concentration of suspended solids and consistently high barium concentrations, averaging, 14.4 mg/I Barium, over the sampling period. A laboratory study of chemical precipitation processes has indicated that about 91% of barium could be removed by using ferric sulphate and lime. On the basis of the information obtained from the environmental audit process an alternative water treatment and reuse system incorporating 51% reduction in the water consumption with 32% less off-site discharge has been suggested (Thomas, 1995).The second case history is concerned with the storm water management at a mine situated in the Illawarra escarpment where only 20% of the wastewater generated in the colliery is discharged off-site. Computer modelling of the storm water system showed that 75% of the clean runoff becomes contaminated through poor management practices and causes the process wastewater treatment system to fail in wet weather. Suggested improvements include relatively simple alteration to the coal wash filtration dams which are expected to reduce the periods of inefficient operation of these dams by 95%. The use of storm water diversion channels and detention basins can reduce the overflow volumes by 70 - 100 % for a ten year ARI (Average Recurrence Interval) storm event (Wingrove 1996).

Jan 1, 1998

By Dickson T. J

Slag cleaning is an important part of the pyrometallurgical operations at the Kalgoorlie Nickel Smelter. It is a complex system with many streams of different phases and composition. Some of these streams are very difficult to control and/or monitor. Through the use of a statistical computer package, called Minitab, key relationships affecting the economical operation of the slag cleaning process have been found. Data for the statistical analysis was collected from all possible variables around the appendage.

Jan 1, 1991