Search Documents

By Burnett C. C H

GEMNet, (Grade Estimation using Mapping Networks), is a grade/reserve estimation software system that uses the artificial intelligence technique known as neural networks to perform reserve estimates from both two- and three-dimensional data samples from a mineral deposit. The system is the result of research carried out over the past three years into the feasibility of using neural networks for reserve estimation at the AIMS Research Unit in the Department of Mineral Resources Engineering at the University of Nottingham. This paper describes the architecture of the GEMNet system including details of the neural network components of the system. The performance of the GEMNet system is then compared to several other widely used reserve estimation techniques on two reserve estimation examples. The results produced by the GEMNet system compare favourably with more conventional estimation techniques, but require fewer assumptions to be made about the form of the data used, and do not require the use of complex mathematical modelling.

Jan 1, 1995

By M E. Trim, J J. Johnson, W Cranston

The Brightwater conveyance system is located near Seattle, Washington in the north-western United States. The East Contract portion of the system consists of a 4.3 km long, 5.9 m diameter tunnel in soft ground and two large shafts constructed in challenging soil conditions. The two shafts are situated side-by-side in an urban valley. One will house an influent structure to direct incoming sewage and outgoing treated effluent, while the other will house a 645 megalitre per day (ML/d) influent pump station. The tunnel contains four pipelines: two force mains to convey untreated wastewater eastward from the new pump station to a new treatment plant, one gravity-pressure pipeline to convey treated effluent westward to a new outfall in Puget Sound, and one high-pressure pipeline to convey reclaimed water from the treatment plant to downstream distribution points. The shafts and the tunnel presented many design challenges. Groundwater is near the surface in the area surrounding the shafts, and compressible peat and clay soils preclude dewatering during construction. These and other challenges were encountered during design of the pump station shaft and multiple-pipe tunnel. The challenges were addressed by a design that includes a dual intersecting circular cell shaft (referred to as æthe peanutÆ) and a single tunnel into which stacked pipes will be æstuffedÆ. This paper discusses the design approach and design details for both elements.

Jan 1, 2008

By Shrivastava P

The iron orebodies of the Pilbara region are formed by supergene enrichment of banded iron formation and rarely do such processes produce orebodies with uniform grade distrib- utions. The orebodies being mined or developed have to be worked to grade/quality constraints imposed by contractual agreement rather than natural characteristics. Hence it is imperative to use a non-biased ore reserve calculation method. The geostatistical study of a typical iron orebody is presented. Emphasised are the geological characteristics of the orebody manifested as a variable grade distribution of iron and impurities; the determination of variogram model; subsequent uses of the model for computation of ore reserves and kriged lock estimates; computation of dispersion variance and conditional simulation of orebody.

Jan 1, 1977

Mine closure is a legitimate element of the mining cycle and like mine development involves technical planning, permitting, and finally construction. Closure begins with the mine's operational footprint and transforms the site so that it meets the explicit requirements of the owners and regulators. Implicitly, the closure will increasingly need to meet the requirements of other interested parties such as the local community, workforce, and future land users. Golden Cross is the first modern mine closure in New Zealand. It operated for 6 + years as a mid-size gold and silver mine winning ore from both underground and open pit sources, and processing via a carbon in leach circuit including a cyanide recovery stage prior to tailings disposal. The mine is situated in a sensitive high rainfall environment, and is complicated by the existence of a large ancient landslide underlying most of the tailings dam and waste rock embankment. The regulatory process for mine closure in New Zealand is not clearly understood by operators or regulators alike. The Golden Cross mine was permitted under the Mining Act 1971 and closed primarily under the Resource Management Act. This switch of legislation, the parallel reorganisation of many government departments, and change in societal expectations with respect to long term environmental stewardship during the life of the mine resulted in the requirements of closure being significantly different to the expectations at permitting.

Jan 1, 1999

Over the past 15 years many world-class gold discoveries have been made in the region. Some deposits, such as Lihir and Porgera in P.N.G., have a contained gold resource that places them among the top dozen deposits ever found on a worldwide basis. Can we see any pattern to these discoveries, or are they the result of good luck or chance by geologists and prospectors who struck it rich? Whilst such discoveries were a feature of the gold rushes of the 1850s and the 1900s, the present boom is now scientifically based. This paper develops an argument that long-tent, multi-disciplinary exploration by experienced geoscience teams underlie the successes achieved. Dis- coveries nearly always reflect a combination of skills, drawn from the areas of geology, geochemistry, geophysics and remote sensing, and a team approach. They do not represent the chance finds of a prospector's pick or such as the Norseman discovery where the gold reef was first noted by the prospector when his horse fell over the outcrop. The following deposits provide major examples of exploration successes within the Australian-Pacific region, it is not an exhaustive list and I have noted other significant producers at the end of this paper. For the Australian mines listed and based on our estimates for 1990 gold production, they represent about 20 per cent of the Australian production total.

Jan 1, 1991

By Monette J. C, Nulty J. H

High temperatures and pressures are required to obtain acceptable stripping rates. Higher chemically induced stripping rates could reduce the need for higher temperatures which lead to cyanide losses. The higher rates could lead to lower carbon inventories and higher gold production. This paper reports laboratory and continuous test unit data which strongly suggest that the preceding can be achieved. New stripping agents demonstrate efficient stripping under conditions of cyanide depletion such as after carbon acid washing. Stripping times for gold and silver can be reduced by at least half compared to caustic cyanide through the use of these novel substances.

Jan 1, 1991

The paper describes the studies conducted to date on the short term adsorption/desorption of gases in coal from the point of view of developing techniques to predict imminent outbursting conditions in coal mines. A number of different parameters such as'dP express, K' and AV 0/60 etc. which have been effectively used overseas were studied on samples of coal from Westcliff and Leichhardt Colliery. Results indicate that these do not seem to be valid indices for predicting an outbursting condition. Based upon desorption isotherms, a new index defined as "L" has been developed which shows promising results. This index is in a position to differentiate the changes in the structures of coal and its proness to outbursts. The "LZ value determinations and its usefulness opens a new field where it would be possible to determine outbursting conditions from existing drill cores obtained during exploration studies or from long holes drilled in advance from underground workings. The index is more or less independent of the time elapsed between the extraction of a sample and the conduct of the test. The test for "L" can be conducted'on site or in the laboratory. The test is simple, easy to carry out and the "L" value for a sample can be calculated in less than 20 minutes. It could be adapted as a routine test for monitoring outburst conditions in mines.

Jan 1, 1980

By OÆNeil G. R

The gold adsorption capacity of ash-char and ion exchange resin Zerolit F.F. (I.P.) was evaluated by obtaining Freundlich isotherms in the presence of selected variables. It was found that the presence of Na , 2+, Ca 2+ cations and SO4 , CN , S Z, 0 2- Zn anions prompted adsorption of gold onto the char and reduced gold adsorption capacity of the resin. Temperature, particle size of adsorbent and pH of solution were found to influence the gold adsorption capacity of char and the resin. The most efficient desorbent for gold adsorbed on the ash char was S2 ions. Optimum sulphide concentrations were found in the region of 1% Na2S. Investigation into the concentration of gold from actual carbon contaminated gold residue dumps in Kalgoorlie area onto ion ex- change resin showed limited success in one case and not so in another. Maximum gold adsorption by the resin appeared when cyanidation and sulphidization treatments were carried out simultaneously in the presence of the resin.

Jan 1, 1979

Optimising drill performance has always been a primary goal of drilling and blasting managers. Improving drilling rates and utilisation will ultimately drive the cost per foot or metre downward. Additionally, more consistent production will ensure shovel or dragline performance goals are met and the chances of machine idle time is minimised. Over the past 20 years, many studies have examined rotary drilling factors and performance issues. In most cases a common theory points to energy input versus drilling output. Indexes such as specific energy and total work energy have been -developed to quantify the drilling process. As general engineering principles dictate, energy is required to drill rock by overcoming compressive and shear strengths. Concurrently, the greater the energy input, the faster the penetration output. Therefore, by examining the basic drilling energy parameters, optimisation is possible. The principles of rotary drilling are driven by five factors. When optimised individually and as a system, drill performance will improve. Most recent studies all agree that a performance relationship exists between bit load, bit rotation, and hole flushing. Additionally, proper bit selection and most of all, the operator, can have a tremendous effect on drill productivity. By analysing these factors and establishing the best case scenario, an overall drilling system can be engineered to match the mining characteristics. Furthermore, by balancing these factors, a lower cost will be achieved through increased production rates, maintenance costs, and effective drill utilisation.

Jan 1, 1995

Krupp Polysius AG, FRG, in close cooperation with Prof. Dr. K. Schoenert, FRG have developed the principle of the high pressure grind- ing roll POLYCOM. The POLYCOM mill basically consists of two counter-rotating rolls of large diameter and relatively small width, one of which is fixed and the other moving in slide blocks. The pressure required for comminu- tion is applied via the sliding roll by a powerful hydraulic system. The comminution takes place between the rolls under high pressure in the bed of material by nipping and compacting. The top feed size-depending on the rolls diameter -may be as coarse as conventional secondary crusher feed and the product is a compacted cake containing a high amount of fines created by micro-cracking. The amount of fines depends on the pres- sure (grinding force) applied. Operating results show that even in wet griding circuits capacity increases at downstream connected grinding mills of up to 100010 can be accomplished with an interconnected POLYCOM machine and energy savings of up to 25070 may be achieved depending on application. POLYCOM can be used in existing grinding plants for low-cost upgrad- ing of capacities but also as an advanced alternative to conventional crush- ing and grinding equipment in open or closed circuit configuration. A single industrial size 2.8m roll diameter POLYCOM machine may be fed with top feed size of up to 200mm and produce a finish product as fine- grained as known from rod and ball mills but with less energy consumption. Meanwhile, the POLYCOM high pressure grinding roll has established itself world-wide in the cement industry and is now entering the mining industry. POLYCOM machines are currently designed in industrial standard sizes of 1.0m to 2.0m rolls diameter and drive units of up to 2400 kW. This paper includes: principles of high pressure grinding, main fea tures of the POLYCOM machine, results of tests on various materials including Australian gold and copper ores carried out at the POLYSIUS research centre in Germany. Some examples of industrial applications of high pressure grinding will also be presented.

Jan 1, 1988

By Bevan JE

The US Bureau of Mines is conducting research to improve the health and safety for underground coal miners, and the efficiency of the mining systems that are used. In 1986, the Bureau began a major research effort on the technology for computer-assisted mining systems for underground coal mines. The initial target was technology for continuous mining machines that would allow them to extract coal by computer-assisted operation. Technology areas being investigated include guidance systems, machine condition systems, computer systems, machine control, human-machine interfaces and planning. In each of these areas, individual system development has progressed to where underground testing of these systems will begin in 1991.In addition to coal extraction, the Bureau has also begun research for the development of technology for computer-assisted roof bolting. The Bureau is developing technology for a "smart" roof bolter that would be able to sense and analyze strata conditions to determine the requirements to provide a competent roof. The system would determine the location of the hole, drill the hole to length, and select and install the appropriate bolt.

Jan 1, 1991

By Swift J. D

A key parameter affecting the performance of gravity thickeners in hydrometallurgical processing operations is the aggregation state of the feed after the addition of a flocculant. New procedures which measure the settling ratelsize relationship and the size distribution of aggregates in their process liquors have been used to quantify the aggregation state of the feedwell, overflow and underflow streams in a tailings thickener. The data obtained have been related to the thickener's operation and to a change in the flocculant dosage. A comparison is also made between the settling rate/size relationships determined with these new procedures and the mud-line settling rates from cylinder tests.

Jan 1, 1991

By Dance A

Highland Valley Copper recently implemented a system of measuring run-of-mine (ROM) ore properties and monitoring their effect on both mine and mill performance. These properties are principally ore hardness and size. For some years, Highland

Jan 1, 1998

By Evans R, McCallum P

Modem blast initiation systems allow users many options for connection and application in the field, and have resulted in more innovative and complex uses of sequencing to influence blast outcomes. However, no tool existed which allowed the blaster to easily and quickly assess the effect of different options. The original requirement was for a computer program which allowed the easy input of blast patterns and the associated initiation sequence, and then permitted the evaluation of different options with respect to established criteria such as the number of holes per delay and angle of initiation. The implementation of this goal saw the development of the SHOTPIan blast sequence design software, with particular emphasis on an easy-to-use menu driven interface and visualisation of the blast sequence. Extensive trialling during development saw the incorporation of additional features requested by industry such as the ability to import from established mine design software packages, and further features such as the calculation of burden relief times. Case studies of the use of the program are provided, where the rapid evaluation of a number of options has enabled blast results to be optimised. Examples are also given of cases involving two-path initiation

Jan 1, 1995

The paper describes the reasons for the development and for the selection of systems which were finally adopted; further estima- tion and design engineering problems, as well as experience with large screens in operation. Advantages, disadvantages and the final li- mits of screen dimensions are indicated.

Jan 1, 1984

By Shuqing L

The application of single liquid cement for fracture grouting in base rock may have history more than 120 years. The disadvantage of it is difficult to increase the grouting efficiency, because the jelling time of it is very long and hard to control. The double liquid grout, such as chemical grouts and cement water glass grout was developed at the end of 1960.'s Although the jelling time of this kind of grout can be controlled, it mast adopt double liquid grouting technology, use complicated equipment and is not easy to control component's ratio of the grout. Another disadvantage for chemical grout is high price, and have pollution to environment. OCE series single liquid grout is the effective grout material developed recently by making large efforts in Ohina. Main feature of it is that the jelling time is easy to control, materials from cement and clay are very cheap and without pollution to environment, and the grout can be injected by single liquid technology. The effect of QCE series grout has been proven by its application in China. It can be believed that QCE grout has great economic efficiency and will give a push to develop grout material.

Jan 1, 1988

By Kukla G. T

A Seam deposit User oriented Mine Planning System (SUMPS) was developed by The Broken Hill Proprietary Company Limited (BHP) at its head office in Melbourne. It is one of the computer mine planning systems developed by the Corporate Data Processing (CDP) section of BHP. To date it has been employed in the feasibility study of four coal prospects for the BHP Group, including Gregory in central Queensland - Ham and Van Hoorn (1978). It was also used in detailed short term mine planning for Gregory. A recent application was in the feasibility study of Saxonvale, a multi seam coal deposit in New South Wales with seams up to 20 m thick. The other two applications of SUMPS were also on thick multi seam coal deposits. Development of programs for the underground sub-section of SUMPS is continuing. SUMPS was developed and implemented on mini computers with graphics and plotting peripherals. The company's philosophy towards computing is one of centralized development and project planning, with transfer of hardware and software to site once the mine becomes Operational.

Jan 1, 1980

In the new refinery, at the works of the Broken Hill Associated Smelters Proprietary Limited, situated at Port Pirie, South Australia, the refining routine is similar to that carried on in the old one in that bullion is progressively refined first for arsenic and antimony, then for copper and gold, then for silver, and finally for zinc. However, actual procedure differs in that each refining operation is now conducted continuously, whereas in the old refinery intermittent batch treatment was practised.The early experimental work was concerned solely with the development of the continuous desilverising process, which, in addition to continuous treatment, embraces the novel feature of conjugate solution formation with consequent production of a silver product relatively high in silver and low in lead.

Jan 1, 1932

In Munich's peculiar hydrogeological conditions (water bearing sand strata between layers of impermeable clay, silt or marl) are proper functioning groundwater lowering methods of decisive importance for underground construc- tion. Shield tunnelling with compressed air has al- ready proved to be successful. In view of growing application of shotcrete tunnelling it was obvious to consider the use of compressed air even here. After a preliminary research-project the first subway section "shotcrete under compressed air" was 1979 awarded in Munich and since that time five sections have been awarded, respectively completed. On the basis of the experiences meanwhile obtained reports will be given stating the frame conditions in which this new construction method can be applied. The tunnels consist of two shells. The outer ist driven by shotcrete under compressed air. In order to keep the air overpressure low, the groundwater often is previously detensioned or partially lowered. The inner shell of watertight concrete is built under atmosperic pressure.

Jan 1, 1987

By Mercer JK

This paper gives a description of the research undertaken by an explosives manufacturer to give better technical advice to the Mineral Industry. Blasting Physics is defined as giving a systematic and coherent account of the initiation and subsequent effects of high explosives upon the surrounding medium. As a result of this work a mathematical model based on the gener- ally accepted mechanism of blasting has been developed. The mechanism and the resulting model are briefly outlined. IFrom'this model the effects of burden, spacing, blasthole diameter, rock and explosive properties upon fragmentation and heave can be calculated. Using these calculations it is then possible to see how variations in frag Imentation and heave can affect the overall production costs of a mine whether it is surface or underground. The overall costs are made up of a number of individual costs - drilling, blasting, loading, hauling and crushing. ach of these operations influences or is influenced by fragmentation and heave s these costs are inter-related, the

Jan 1, 1975