Search Documents

By M Ljunggren, M Lundh

Dissolved air flotation (DAF) in wastewater treatment as a separation process of submillimetre biological flocs is based on the generation of bubble/floc aggregates. DAF is a complex process but has got advantages, such as allowing a high hydraulic load, compared to sedimentation. A thorough knowledge of the physics of the DAF process is, however, still lacking. This paper will present results of experimental studies on three aspects of significance to the separation process û the flow structure in the flotation tank, rise velocities of aggregates, influence of floc size on the separation efficiency. Flow structure. Measurements were performed in a pilot plant mapping and visualising the velocity field. The dispersion water (bubbles) had a decisive influence on the flow structure due to the effect of the bubbles on the bulk water density. Stratified conditions with a less dense, bubble-containing upper layer and a clear water, denser bottom layer were important for a good separation. A simple model of the stratified flow structure was elaborated making it possible to interpret the function of the aggregate rise velocities. Bubble/floc aggregates. The dynamics of single flocs, bubbles, aggregates were visualised using a borescope + CCD video camera + digital recorder + image analysis. Sequences of video frames made it possible to determine the rise velocities of the single aggregates. These velocities were found to be in the range 1 - 9 mm/s with a tendency for large flocs to have higher rise velocities. Separation versus floc size. The floc size distribution was measured in the DAF process. Data from three different DAF cases showed, that large flocs (> about 100 ¦m) were entirely separated, whereas small flocs experienced a less good separation. It was, moreover, found, that a very significant separation of flocs took place in the very upstream end of the separation zone in a pilot plant case.

Jan 1, 2005

By Fabjanczyk MW, Nemcik JA, Matthews SM

The major strata control considerations which affect the optimisation of roadway driveage in highly stressed strata is the performance of reinforcement placed and the extent of stress induced rock deformation. High development rates and opening stability requires efficient rock reinforcement and stress relief strategies which maximise the integrity of the rock about roadways created. Current studies demonstrate the capability to reduce lateral stress distributions across panels and research is aimed toward a higher capacity bolting system. It is the intention to provide industry with more efficient reinforcement and stress control alternatives which will allow high production development equipment to operate without the restriction of delays caused by poor ground Conditions.

Jan 1, 1988

By Rongqing Q, Tiancong Z, Yiyuan L

The influence of pulp density, ferric ion concentration and particle size on the tank bioleaching of two kinds of refractory gold concentrates are discussed. The chemistry and mechanism of the bioleaching process are also presented. The relationship between oxidation of sulphides, liberation of enclosed gold and gold cyanidation are discussed. The consumption of NaCN could be reduced by alkaline treatment of bioleached residues prior to Cyanidation.

Jan 1, 1992

Viking Holdings Ltd, a Todd Corporation company, is active in the mineral industry through operations, joint ventures and equity investments. Identification and management of risk is key to the success of the company. This paper discusses risk in general terms and in the context of Vikings activities. Reference is made to the current environment and the impact of risk and environment on profitability.

Jan 1, 1997

By Nolan D. P, Balales M

Over the last two years work has been undertaken within the Pasminco Metals - BHAS Zinc Plant to improve the efficiency and maintain the production capacity of the operation. The work has centred upon the installation of suitable process instrumentation to improve process control and the development of new unit operations to maintain control of the circuit water and sulphate balance. A key aspect of the new process instrumentation has been the development of an on-line analyser to monitor the total antimony concentration during zinc dust purification. As a result of changes made to the Zinc Plant in order to contain all effluent within the circuit, a problem developed with control of both the water and sulphate balance of the circuit. A new neutralisation plant to treat all cell house waste water so that it can be contained within the circuit has been developed and installed. In addition changes have been made to the existing circuit to control deliberately the circuit sulphate concentration by precipitation of sodium and potassium jarosite.

Jan 1, 1993

The Auscoke project has reached-a stage where a pilot plant nominally able to produce 100 t.p.d. of coked briquettes is being brought on stream during Nov. 1971 . The targets for this stage of the project are to establish the technological and economic value of Auscoke for the iron blast furnace, and to verify the commercial feasibility of large scale plants. The project originated at the B.H.P. Central Research Laboratories (C.R.L.) and work to date has shown that using a two stage contin- uous process, strong large coke can be produced at good productivities from medium or low volatile poorly caking coals. General features of the pilot plant and processing are discussed.

Jan 1, 1972

A standard practice of auditing mill designs has developed in the mining industry. The purported aim of this task is to ensure that the mill being offered conforms to the design specification, thus reducing the purchaserÆs risk. However, careful examination of the auditing methods used in the past shows that this is not the case. In some cases, what auditors have been providing is effectively a quality assurance check of the input data, not a full independent audit of the vendorÆs design. It will be shown that these past auditing methods have contributed to the stagnation of mill specification development. This lack of specification improvement combined with the current trend towards increased allowable fatigue stress ranges can result in an increase in risk for the purchaser.

Jan 1, 2002

We are all no doubt aware that with today's high costs it is more important than ever to get the maximum possible return on capital invested in the mining industry. Screening is an important and often costly process in the size classification of industrial minerals and for this reason alone it is essential for both managers and operators to fully understand what type of screening equipment is best suited for a particular application and why. The advent of elastic materials such as rubber and polyurethane have added a new dimension to the process of screening. It is important to understand why the physical properties of these materials can be of benefit in the screening process, and recognise which type of screening applications best take advantage of these orooerties.

Jan 1, 1984

By Grinenko VA

Mineralogical, chemical, and isotopic data have been obtained for samples from 11 volcanoes and 4 kortlandite intrusives on Kamchatka.Similarities and differences in ore-bearing and barren intrusives are discussed. Differences in sulphide mineralization and sulphur isotope compositions of intrusives are explained in terms of the "auto-sulphurization" hypothesis which involves the redox conditions of the host rocks. possible role for carbon in nickle sulphide ore formation is also considered.

Jan 1, 1990

A short overview of the research program of SveBeFo, Swedish Rock Engineering Research, which was founded in 1993 is first given. Then four recent and ongoing projects in rock blasting and explosives engineering are presented in greater detail: 1. Burn Equations for Commercial Explosives. 2. Blast Damage in Contour Blasting. 3. The Role of Gas Pressure in Pit Wall Damage. 4. Fragmentation of Aggregate Rock. The goal of the bum equation project is to be able to control the energy release from explosive charges to the desired part of the expansion curve of the reaction products under various rock conditions. SveBeFo's work has reached the stage where a burn equation for a lab emulsion has been established which can model the influence of charge diameter on the VOD and detonation front curvature in a cylindrical charge quite well. This work now continues with other emulsion recipes. In the blast damage project the goal is to develop techniques and recommendations on how to minimise the blast damage in construction blasting. The project has gained extensive practical knowledge from the blasting of more than 200 holes in a granite quarry under controlled conditions. The cracks in the rock surrounding the contour holes have been cut open and measured. The influence of factors like charge concentration, decoupling ratio, hole and charge size, VOD and time delay in initiation have been investigated. A simultaneous initiation of a group of contour holes with EDD detonators is quite superior to single hole blasts, even when they are timed as closely as 1 ms.

Jan 1, 1995

By J Chen

Research conducted into backfill drainage at Mount Isa Mines since 1992 is described. Piping in draining backfilled stopes has been the primary cause of bulkhead failures and emphasis is placed on research into the piping mechanism. Laboratory and in situ tests aimed at understanding the piping mechanism have been conducted and the results are presented. A case history of piping in a draining bench stope fill mass is described and a technique for reducing the potential for bulkhead failures in bench stopes is presented. Hydraulic fill is produced by standard cycloning of tailings and the overflow (reject material) is sent to thickeners prior to placement in the tailings dams. Research into the partial introduction of thickener underflow into the backfill system and its influence on backfill drainage is also described.

Jan 1, 1998

By D Clarke, R Simpson

The Main lode in the Anwia Gold deposit is difficult to interpret due partly to the fact that three separate grid and drill hole orientations exist over the area and partly due to a lack of understanding of the controls on the high-grade mineralisation. Scattered high gold grades and multiple veining orientations add to the confusion. Sectional interpretations of the lode are often misleading due to the multiple orientations of drilling. Initial attempts to define a high-grade constrained geological model were not successful due to the inability to establish any geological continuity that would hold together in three dimensions. As a consequence the initial geostatistical domaining for the Main lode at Anwia comprised a simple broad mineralised envelope split by the weathering profiles. Subsequently an analysis correlating subjective qualitative logging information with grade plus utilisation of LeapfrogTM software, together with extensive geological re-interpretation resulted in the definition of a coherent high-grade shoot within the Main lode. The resource was re-estimated including this new domain as a high-grade hard boundary. Estimations on both models were carried out using uniform conditioning, which is a recoverable resource estimation methodology that estimates tonnages and metal above a series of cut-offs for SMU (selective mining unit) sized blocks. This paper compares the tonnages and metal contents that are calculated from the two estimation runs, both at a zero cut-off and a series of higher cut-offs. The results confirm that the estimation methodology has been implemented correctly as the tonnage and metal content at zero cut-off is the same for both models. The resource tabulations and grade tonnage curves predicted by the two models highlight the differences that can occur at higher cut-offs when realistic high-grade domaining is implemented. The results also reinforce the point that recoverable resource models are intended to address selectivity issues and are not substitutes for good geological modelling. Recoverable resource techniques, such as uniform conditioning, will not correctly estimate high-grade zones that have not been explicitly modelled.

Jan 1, 2006

By Leach T

The Tolukuma Gold Deposit is hosted by metamorphic and volcanic rocks, and igneous intrusions. Dilatant structures for the main veining appear to be provided by post-metamorphic flexure/faulting; syn-mineralisation tectonics is recognised from the en-echelon patterns of much of the veining. A SSE trending structure containing high grade mineralisation has acted as a major dilational zone within or at the contacts of porphyry intrusions. An ESE trend has controlled numerous dilational structures splaying eastward from the SSE vein structure and containing medium grade mineralisation.Early hydrothermal activity (Stage I) is represented by unmineralised, pyrite-rich brecciation and fracturing. Associated chloritic veining is indicative of single phase neutral-chloride fluids upwelling in relatively low fracture controlled nenneahility

Jan 1, 1993

Methane predrainage from coal seams in the Western Area of the U.K. has been practiced over the past decade. The differing reasons for the practice include the controlling of gas emission rates in coal headings required to win out coal faces and also the need to control the gas emission rates in the roadways of retreat faces in order to comply with the statutory requirements. There are some similarities with predrainage experience in the Bulli Seam NSW. The several case studies highlight the varying conditions in the Western Area coalfield where the use of predrainage was Required.

Jan 1, 1982

In North-West Nelson the Riwaka Complex, a linear basic intrusive complex, is exposed for approximately 45 kilometres. Some 500 kilometres south, across the Alpine Fault, a linear zone of similar but less well known basic intrusives that may be correlatives of the Riwaka Complex is exposed discontinuously for about 80 kilometres. The Complex was emplaced at several centers along a major tensional fracture zone that developed in upper Carboniferous to Lower Permian time. This fracture zone probably formed in response to the development of a west dipping subduction zone that gave rise to the Permian volcanic arcs in east Nelson and western Southland. The Riwaka Complex contains three rock suites. The Fractionation Suite, characterized by cyclic mineral layering and small scale cumulus banding is the largest and is divided into the Ultramafic, Hornblende and Plagioclase Series, each of which is subdivided into several units. The Cumulus Gabbros represent a restricted but important suite of unusual composition, while the third suite is the late phase Diorite Suite.

Jan 1, 1980

By Wright S

The feed to the Cockle Creek Imperial Smelting Furnace consists of mixed Pb/Zn con- centrates and lead sulphate-containing elec- trolytic zinc plant residues. Roasting was investigated as a means of desulphurizing the feed to less than 1%. Laboratory studies showed that two process streams were required in which concentrates containing 20% Pb were roasted separately from the leach residues. The residues along with fume from the roast- ing and a portion of concentrate were desul- phurized by means of the roast reduction reaction. Conditions were defined to give

Jan 1, 1986

New Zealand Steel Limited is nearing completion of the environmental reporting and planning procedures for its proposed fivefold expansion to steelmaking at Glenbrook, and supporting mining operations at Waikato North Head. A report on the proposal to transport concentrate from the mining operations to Glenbrook has also been prepared and is awaiting release. This paper draws from these events, and by discussing some of the problems encountered, gives some guidelines for the preparation of an Environmental Impact Report.

Jan 1, 1981

By Butters S. E, Deslandes J. V

The selection of loading and haulage equipment in a proposed or oper- ating mine is vital in ensuring the cost effective achievement of produc- tion targets. To assist in the evaluation of different haulage systems, a truck haulage simulation model has been developed at BHP Melbourne Research Laboratories. The operation of the model is described and exam- ples of an actual application at Mt. Whaleback Mine is presented.

Jan 1, 1989

By I P. W Chau

Construction of twin stacked railway tunnels through mixed ground conditions in the heavily populated urban environment of Hong Kong, including tunnelling in poor ground conditions, with low cover and under or adjacent to sensitive structures with minimal impact was the challenge presented by the tunnelling section of the Kowloon Southern Link project. This paper details how twin 1.1 km tunnels of 7.0 m internal diameter were driven by Mixshield tunnel boring machine (TBM) in mixed ground through one of the exclusive shopping and hotel districts in Kowloon. The paper addresses the challenges required to be considered and managed for the success of the project, including ground conditions, TBM selection, Mixshield TBM operation, settlement monitoring and control, ground- borne noise and vibration, proximity to utilities, buildings, roads and operating railways.

Jan 1, 2008

A new experimental procedure for determining the solids flux curve is detailed. The procedure is based on measuring the concentration at various heights of a bed of settled solids formed during a semi-continuous sedimentation test. Unlike conventional thickener area calculations, the test procedure demonstrates the dependence of the flux curve on the system feed flux. At a given feed flux, there was good agreement between the solids flux curve determined by the method and continuous sedimentation results. The widely used method of Kynch was found to be restricted to relatively high effective feed fluxes and consequently there was poor agreement with continuous tests at low feed fluxes. The flux curve determined by the method of Coe and Clevenger was invalid for all feed fluxes. A case study shows how the required thickener area would vary for a number of fine coal processing options.

Jan 1, 1989