Search Documents

By R Blin, R Walde, R Belli, D Inaudi

A fiber optic distributed sensing system allows the monitoring of parameters useful to determine the short- and long-term behaviour of the structure in response to the external actions, including, eg seismic activities as well as long-term phenomena such as seepage, tunneling, sinkholes, and other geo-structural movements. Monitoring of large retaining structures with such a system provides direct strain/deformation and temperature measurements on the broad interior area with an arrangement of several sensing cable lines, enabling early detection, localisation and sizing of subsurface damages. Measurements are provided every meter along the entire sensing cable, this is particularly important in such cases where the location of defects and damages cannot be predicted. Fiber optic distributed sensing cables are generally available for retrofit installation inside the dam structure using trenches on the downstream face or laid during construction below the geomembrane liner within the bedding sand layer. Mapping the cable route enables exact correlation between a linear coordinate on the cable length and a position in the dam. Cable installation is envisaged to be carried out during further raising of the embankment; additional cable sections are plugged to the previously installed cables and measured with the existing measurement system, requiring only an update of the mapping. The measurement system is placed remotely from the sensing area since a section of sensing cable can be used to link to the sensing area at the storage facility several kilometers away. The system is available for on-line, 24/7 real-time operational data management. Such fiber optic distributed sensing systems allow storage facilities to be monitored with long, accurate, continuous and precise data for geotechnical diagnostic purposes. This contribution will introduce the principles, benefits, and limitations of this technology.

Jul 1, 2021

By LefTvre Y

In May 1991, AZSA commissioned a new conventional Cell House. This paper focuses on the major improvements introduced in the design and the construction of the equipment, machinery and control. An effective control system together with good reporting and routine operation has resulted in quality control of the Cell House at the highest possible level. Consequently the monthly current efficiency consistently averages above 93 per cent with a total energy usage of 3000 AC kWh/t of cathode zinc. The new concept for the year 2000 and beyond is introduced.

Jan 1, 1993

The main features and recent developments in the processes of benefication and extractive treatments of tin ores are reviewed. The need for development of processes to recover fine tin, tin from low-grade complex ores and from hard rock resources is indicated. The progress in understanding of slag-metal interactions and developments of fuming processes on industrial scale is delineated. the processes and prospects of hydrometallurgical and chlorination methods are briefly indicated.

Jan 1, 1992

The metals titanium and zirconium and their alloys occupy individually unique positions in the catalogue of metallic materials available for engineering applications. Because of the uniqueness of their usage in the aerospace industry, in the case of titanium, and in the nuclear industry, in the case of zirconium, the except- ional resistance of both the metals to the majority of corrosive media is often overlooked. The cost factor in the application of these more exotic metals has, in the past, been a major considerat- ion in the rejection of titanium and zirconium as constructional materials in areas of usage where their superior corrosion resistance strongly favoured them over more conventional metals and alloys. The cost differential, vis-a-vis austenitic stainless steels, for example, is not a trifling matter, being of the order of 6 : 1, when compared on a weight basis. However, if one considers the cost, for, say, sheet product on an area basis, the ratio is redgced to approximately 3.4:1. If one also takes into account the enhanced performance of the more expensive material and the sub- sequent increase in service life and decrease in plant down-time, the economics of the usage of materials such as titanium becomes much more attractive and, indeed, highly competitive,

Jan 1, 1969

The paper describes developments since 1959 in major excavators to meet the demand for higher outputs of overburden and coal under less favourable batter conditions than used hitherto in the coal deposits of the Latrobe Valley. Particular reference is made to investigations of designs of bucket wheel head configurations for the digging of these flat batters on high faces, and examples are given of the wide use of models inthese studies. An explanation is given of how solution of these problems and surface conditions unfavourable for wheeled transport confirmed selection of the long boom rather than the compact type of bucket wheel excavator for the Latrobe Valley applications.The past decade has seen advances in the manufacture in Australia of components for excavators and similar machines. The history of Australian manufacture of components for major brown coal excavators is traced;and reference is made to study and application of Australian and overseas (mainly German) codes and practices in the design and construction of machines made partly here and partly in Germany.A section of the paper deals with advances in electrical engineering for large excavators in Australia and its interdependence with mechanical design and construction.Finally, as an example of the versatility of the bucket wheel excavator, a description is given of a recent application for the mining of mineral sands in northern N.S.W.

Jan 1, 1971

By Glassock C. D

Most Australian mining projects are becoming smaller, more remote and with lower grades of ore. Their small size has been making it harder for mining companies to absorb the large infrastructure costs. This has forced companies to reduce those costs in every way they can. Social factors, environmental groups and even tax laws have added other pressures to force down the infrastructure costs for remote projects. For the last ten years, the downward trend in costs has been marked. It seems certain to continue for years into the Future.

Jan 1, 1997

By Jones M

The concept of precise, accurate timing with Electronic Delay Detonators (EDDs) was first seriously addressed in the mid-1980s and much was made of the cheapness and profusion of digital watches in terms of the likelihood of EDDs also being cheap and easy to produce. Ten years later, with every major explosives company and many electronics groups having instituted projects to capitalise on the promise of these devices, production devices are still to come into general use. In South Africa, Expert Explosives units have been used in most applications during proving trials and more recently for production blasting in underground ring stoping and open cast coal. The outcome has been valuable learning both as to the benefits and technical requirements for electronic delay blasting, and especially, safety aspects. Examples are shown of production blasts which utilised the power of EDDs. It is evident that it is not delay accuracy alone which determines the value of these systems, but the whole robustness, flexibility and ease of delay allocation when harnessing blast engineering knowledge. Muckpile movement and shape, fragmentation and vibration frequencies have shown to be greatly influenced by designs which can be implemented no other way. The flexibility of a system and the power of the software controlling it are crucial in capitalising on blasting potential, which lies in integrating control of blast timing with other developing electronic Technologies.

Jan 1, 1995

By A Nigam, K Biswas, R Sarkar

Because of the problems with 1st and 2nd generations of Advanced High-Strength Steels (AHSS), a 3rd generation of AHSS steels has become prominent and these steels have properties in between the 1st and 2nd generations of AHSS. However, although the 3rd generation of AHSS is a promising candidate as a replacement for its predecessors, there remain some challenges in processing these steels which are essentially medium Mn (Mn content ~ 5–7 wt per cent) and high Al (Al content ~ 1– 3 wt per cent) steels. The use of conventional casting powders based on the CaO-SiO2 system is unsuitable for high and medium Mn/Al steels. This work investigates the development of CaO-Al2O3- based mold fluxes for casting third-generation AHSS steel. Mold fluxes, with otherwise similar compositions but different C/A ratios, are tested and their crystallisation behaviour is examined using differential scanning calorimetry (DSC). A calcium aluminate phase having a composition Ca12Al14O33 was found to be the main crystalline phase in the mold fluxes. A decrease in crystallisation temperature was observed as the CaO/Al2O3 ratio increased from 1.00 to 1.33. The effective crystallisation rate constant exhibited an increase with decreasing crystallisation temperature, indicating a potential influence of nucleation rate on the overall crystallisation rate and suggesting an anti-Arrhenius behaviour in the crystallisation process of these mold fluxes.

Aug 21, 2024

Coal washing practice can be improved not only by critical examination of the plant being operated but also by studying plants operated in other areas. The developments at the Australian Iron & Steel Pty. Ltd. plants are discussed in relation to experiences there as well as developments which have taken place in Queensland in recent years. Early A.I.S. problems involved small coal cleaning in heavy medium cyclones and flotation. A proposed future plant flowsheet for A.I.S. is considered in the light of these experiences. Reference is made to plants operated by the Thiess, Peabody, Mitsui Coal Company Pty. Ltd. at Moura and the Utah Development Company's plants at Blackwater and Goonyella in the development of coal washing prac- tice in Australia.

Jan 1, 1975

By A C. Robertson

Studies by Tennent, Isokangas Pty Ltd (TIP) have indicated that underground quarrying of backfill may be a cost competitive option for providing backfill for specialised situations in underground mining. Situations where suitable bulk fill material may not be available on the surface, and where the total cost of setting up a fill distribution system are prohibitive, could favour the mining of fill material underground adjacent to the stopes being mined. Considerations include environmental impact, scheduling, surface constraints and total costs. The examples quoted in this paper, and the case studies are based on the authorsÆ personal observations and experience.

Jan 1, 1998

Hydraulic backfill is generally retained in slopes using permeable barricades. Mitchell et a! (1975), Mitchell (1992) and Grice (1989) have shown that under normal drainage conditions, barricades experience low levels of loading. Cowling et a! (1988) have also shown that barricades are susceptible to piping failures if excess water has ponded on the upper backfill surface and if leakage of backfill from the barricades has occurred. During 1997, six hydraulic backfill barricades failed in four different Australian mines. Fortunately, in each case, the quantity of backfill slurry released was small, and no injuries to personnel nor damage occurred. Detailed investigation of two of the incidents showed that the primary cause of failure could be attributed to the delivery of excess quantities of transport water from the low-density slurry. For each of the incidents investigated there was evidence of the development of piping failures, which resulted in hydrostatic loading conditions on the barricades from the ponded water on the upper backfill surface. The circular failure surfaces in the barricades were characteristic of the application of point loading Conditions.

Jan 1, 1998

By R S. Sing, M D. Yadav, G Udaybhanu

This paper presents the results of the first part of a research project to study the effect of various inhibitors to reduce the spontaneous heating susceptibility of some highly susceptible Indian coal seams. In this investigation 11 inhibitors were chosen and applied at three, five and ten per cent of their concentrations in an aqueous solution for four coal samples collected from four different seams. The susceptibility of coal samples, before and after application of these inhibitors, was determined by carrying out crossing point temperature (CPT) analysis. The findings of this study have indicated that it is possible to retard the tendency of spontaneous heating of Indian coals to a considerable extent by the application of six of the inhibitors studied. Further, these inhibitors were tested in 1:1 combination to study their synergistic effect. Finally the economics of the application of these inhibitors has been analysed and four inhibitors are recommended for field use. These results have direct application to control fire and improve productivity and safety in coal mines.

Jan 1, 2005

The exposed high face of Kerr's Quarry has dominated the township of Ferntree Gully for half a century. The near perpendicular face of bare dacite rock is a crumbling scar in an area of significant natural beauty. Apart from being unsightly, the face is a hazard for any person who approaches too close to its base or to the top edge. The height and the precipitous nature of this man made wall of rock is hazardous indeed. (fig. 1) The rock face is on the municipal boundary between the Shire of Sherbrooke and the City of Knox. This boundary was drawn when partition of the Shire of Ferntree Gully took place. There are many advantages in benching back the wall of the quarry but to do so the operation, located in Knox would need to extend into Sherbrooke. There are planning difficulties involved in such a manoeuvre, but during 1972, at a meeting of Cabinet Ministers, it was agreed that the matter be resolved.

Jan 1, 1976

By L Neems

In conjunction with Orica Explosives, Worsley Alumina have managed a program of continuous improvement to their cap rock blasting over the last two years. Blasting conditions are challenging because of the hard and shallow nature of the material. Blasting costs must be controlled and the environmental consideration of noise and dust is critical. Worsley have sought to determine the optimum balance between drilling and blasting costs and fragmentation. As the cap rock has few inherent weaknesses, loader productivity is strongly controlled by the degree of fragmentation from blasting. The optimum blasting solution is also constrained by maintaining airblast levels at the surrounding residences below 115 dBL . The major blast design parameters optimised during the program were stemming type, stemming length, powder factor and blasthole diameter. A series of carefully managed trial blasts were fired during 1997 and 1998 to quantify the effect of these parameters. Fragmentation was digitally measured using OricaÆs Powerseive G technique. Shovel productivity, airblast levels and blasting costs were also quantified. As a result of the project, Worsley now have an increased knowledge of the key parameters driving blast performance, and their consequent impact on downstream processes, the environment and total mining cost.

Jan 1, 1999

By T Bednarz

The present work proposes a distributed collaborative immersive virtual reality framework for prospective applications in the mining industry. A human-centered approach is described, with people being placed in the central position and surrounded by tasks that are to be carried out. Those tasks can be then achieved through synchronous or asynchronous communication, interactions using properly constructed user interfaces, virtual and/or augmented realities and computer vision. Several examples of such arrangements are presented. One of the applications facilitates an e-learning experience by providing a very familiar object – a book – as a target for users to interact with. Importantly, this system has the potential to provide an ‘enhanced’ teaching medium, as humans tend to remember events/situations better when they experience those events in person, when the immersive factor is involved. The immersive virtual reality environment enables a user to interact physically with various 3D objects and experience behaviours, which in turn reinforces the idea that doing leads to learning. This prototype system can be implemented as an efficient and cost effective e-learning and training platform for different engineering domains. At another level, the same technology can be used in the tele-operation of mining equipment for the future mine.

Nov 22, 2011

The Sishen iron-ore-mine produces 3 pro= ducts with size gradings of 25 to 8 mm, 11 to 5 mm and 5 to 0,2 mm and has a product capacity of 20 Mtpa. Ore is produced at an average Fe content of 66,2 % Fe for the two coarser pro= ducts and an average of 65,3 % Fe for the fine ore product. Three stage crushing is practised to re= duce the run-of-mine ore to -90 mm after which it is screened into five different size frac= tions of which four are heavy media beneficiated in static baths and cyclones and the fifth frac= tion discarded to slimes dams. A final three stage crushing and screening process is employed to produce the final three Products which are homogenized by means of blen=ding systems nrinr to despatch.

Jan 1, 1987

GENTLEMEN, I have to thank you very much for the honour you have conferred upon me by electing me President of the Institute for this year. On behalf of resident members, I have to offer the visitors a very cordial welcome to Mount Morgan, and to tell them that all arrangements have been made to enable them to inspect the mine and works at their own convenience, and to supply them with any particulars they may need.It is very pleasing indeed to see such a large gathering, especially on account of the long journeys many have undertaken in order to be present. The first congress in Queensland, about eleven years ago, was attended by a comparatively small number of members, and a rather long time has been allowed to pass in consequence. The large attendance at this meeting encourages the holding of meetings in Queensland more frequently. Owing to the long distances, and the number of mining centres in Australia and New Zealand, we cannot expect to meet oftener than once in six or seven years in...

Jan 1, 1911

By T Y. Ko, Y S. Kang, S J. Park, J H. Hwang

The lunar subsurface, particularly the lava tubes formed by ancient volcanic activity, presents a promising environment for establishing safe and sustainable human habitats on the Moon. Tunnel Boring Machines (TBMs), widely used for excavating tunnels on Earth, offer a potential solution for developing these subsurface spaces. However, the unique lunar conditions, including extreme temperatures, high vacuum, radiation, and the extraordinary strength and abrasiveness of lunar rocks, necessitate significant adaptations to existing TBM technology. This study investigates the feasibility of utilising TBMs for lunar subsurface exploration and base construction, addressing the challenges posed by the harsh lunar environment. We review previous conceptual designs for lunar TBMs, highlighting their strengths and limitations in addressing these challenges. Additionally, we explore innovative excavation methods, such as microwave-assisted rock weakening and undercutting techniques, to enhance the efficiency and effectiveness of lunar TBM operations. By evaluating the geological characteristics of the lunar crust and analysing the potential of lava tubes as launching points for TBM operations, this study provides a comprehensive assessment of the technical requirements and operational considerations for lunar TBM implementation. The findings of this research contribute to the growing body of knowledge on lunar base development and pave the way for future human exploration and utilisation of the Moon’s subsurface resources.

Sep 1, 2024

By Riley S. J

The basic aim of mine planning is to design mine layouts and schedules that achieve optimisation of operations, minimum cost and maximum resource recovery. Successful accomplishment of this aim is facilitated by timely and comprehensive rehabilitation planning commencing at the pre-feasibility stage and continuing until the end of mining. Incorporation of a final landfomt design for waste rock dumps in a mine plan requires a prediction of surface stability, which may be achieved through erosion modelling. Erosion prediction models can be placed in two broad categories: soil loss prediction models eg USLE and CREAMS, and geomorphic models such as SIBERIA. A waste rock dump landform design based on selected slope form and grade and drainage systems should be developed as part of planning. A digital terrain model (DTM) of the landfonn should then be produced which can be modelled for long-term erosional stability using pre-determined parameter values. If acceptable standards of stability are not achieved, the landform should be redesigned and remodelled until the desired result is obtained. The planning process incorporating models requires knowledge of spoil or waste rock properties and model parameter values. This information is site specific and can be obtained from drill cores or costeans at the pre-mining stage and from spoil or waste rock during the mining stage. Realistic model parameter values are critical in post-mining landfonn design and can be obtained by several methods, including rainfall simulation, monitoring, geochemical analyses and grain size analysis.

Jan 1, 1994

By Whiten WJ, Narayanan S

Data from ball mills of a wide range of sizes are analysed using detailed mathematical models and non-linear least squares fitting techniques. This analysis reveals that the relative power inefficiency of large ball mills is due to inefficient grinding of coarse (plus 4 mm) particles in these mills. A qualitative physical hypothesis is proposed to explain this behaviour. The results of the analysis can be used to scale up ball mill behaviour, using the mathematical models and techniques developed. A simpler ball mill scale-up procedure is also proposed, and its limitations stated. Laboratory experiments are being conducted to determine the average size distributions of single particles of different ores after breaKage. These experiments can distinguish between the different ores, and it is hoped to use their results to model and predict the grinding of different ores in ball Mills.

Jan 1, 1978