Search Documents

By Montini A

The dynamic behaviour of the load in a pilot-scale ball mill has been measured as a function of axial position within the mill, end plate lifter design, load volume J (percent of mill volume), percent solids in the slurry S and mill speed N (percent of critical speed). Conductivity probes were inserted through the shell of the mill to provide online measurements of the dynamic orientation of the load in the mill. It was found that 1. the height of the shoulder of the load is increased by increasing J, S or N. 2. Measurements of the effect of S on the location of the shoulder of the load should be very useful in mill control strategies. 3. The axial centre of gravity of the load in the mill is not affected by operating conditions. 4. The presence of lifters on the feed end plate does not affect the torque drawn by the mill. 5. Holdup of slurry in the mill is a strong function of slurry viscosity and a weak function of mill speed.

Jan 1, 1986

By Cliff D, Harrison P. Hester C

During 1997 two different types of coal mine inertisation equipment were trialed in separate underground coal mines in Queensland.In April 1997 tests of the Polish developed GAG-3A inert gas generator were carried out at the Collinsville No 2 Coal Mine. These demonstrations indicated that the GAG-3A device was applicable in underground coal mines and that with respect to inertisation rate the device outperformed all other currently available techniques. The unit was assembled rapidly and operated safely during surface and underground trials and no mechanical problems were encountered with the device. The GAG-3A is not suitable for every fire scenario particularly if large volumes of fresh air are being drawn into the mine(where multiple units may be required), but with respect to the selection criteria developed by the Moura Implementation Process Task Group 5 criteria, the unit performed up to the specifications required.

Jan 1, 1998

By Lilly PA, Kavetsky AP

An empirical, kinematic model is developed which calculates the trajectory of individual blocks of rock in a blast, their point of impact in the muckpile and the final shape of the muckpile. The method is based on the determination of initial block velocity and requires input on stemming length, bench height, subdrill, burden, spacing, energy of explosive per unit length of blasthole, energy attenuation rate and resistance to movement. The model, which will form part of a comprehensive blast simulation package, has application in open cut mining in predicting muckpile geometry and the movement of grade blocks during blasting, which in turn impact on shovel productivity and grade control.

Jan 1, 1986

The addition of a thallous salt to the cyanide leach of a calcined pyritic concentrate causes a marked increase in the"rate of extraction of gold. This probably is due to the activation of passive gold by.th,e. thallous ions'.''Lea'd, bismuth, and mercury salts, which should produce ' a, similai effect, fail to do so. It is postulated that'this latter result, together with'the reprecipitation of silver at low cyanide levels, is due to the presence of soluble sulphide. The use of thallous salts to reduce leaching time is discussed briefly.

Jan 1, 1964

By Artieda JJ, Catalina JC

- The aim of this paper is to analyse the possibilities of applying signal processing and artificial vision techniques to the ore sorting problem. In order to overcome the limitations imposed by the classical approach to the problem, which essentialy cons

Jan 1, 1985

By Newell RB

Grinding circuits are used in most mineral processing plants. Their widespread application makes the efficient running of the circuits essential to almost all resource projects. This paper will show that, with the application of modern multivariable control techniques, improved plant performance can be obtained when compared with conventional single loop control strategies. Results are presented for a simulated closed-circuit ball mill.The grinding circuit was controlled using the rod-mill water and primary and secondary sump dilution flowrates as the manipulated variables. Variables controlled were the primary cyclone feed flowrate, the primary cyclone feed density and the particle-size measurement (percentage smaller than 75 um).

Jan 1, 1985

By L H. Chapman, I J. Kelso, N H. S Oliver

Utilisation of modern 3D visualisation tools, can improve our ability to correlate between different datasets, and thus to produce more accurate geological models. Here, we present an application of such techniques to the Century Zinc Deposit, northwestern Queensland, Australia. This stratiform orebody is the second largest Zn resource in the world (167.5 Mt at 8.2 per cent Zn, 1.2 per cent Pb, and 33 g/t Ag). It is hosted in the Page Creek Syncline affecting Mesoproterozoic shales and siltstones of the Wide Supersequence of the Isa Superbasin. As in other deposits, (eg McArthur River, Lady Loretta, George Fisher and Dugald River), the mineralised sequence is bound by an important regional structure, the Termite Range Fault, which partly intersects the deposit along its Eastern side. This fault is thought have been active during sedimentation and probably also during mineralisation of the lowest part of the Wide Supersequence. The anastomosing geometry of this fault system and crosscutting relationships with other NE trending structures indicate that it was reactivated several times from Mesoproterozoic to at least late Devonian times (>1000 million years in total); as a result, the ore sequence is subdivided into several fault blocks.Using two different computer modeling packages (GOCAD and 3ds max), we have reconstructed and restored the stratigraphic horizon with the highest Zn content, realised a series of isopach maps for each mine scale stratigraphic unit, plotted the three-dimensional distribution of Zn, Pb, Ag, Fe and SiO2, and have begun to evaluate the degree of correlation between thickness changes and sulphide zoning. With this approach it is possible to better understand the timing of mineralisation from a genetic perspective, because the origins of the orebody are controversial. Three-dimensional reconstruction is a vital tool for identification of syn-sedimentary and post-sedimentary fault activity. In conjunction with sulphide precipitation, these are factors that greatly influence the stratigraphic thickness distribution. Post-sedimentary deformation can be recognised directly by core logging and pit mapping, but the effect of tectonic movements during sedimentation (growth faults in particular), that represents a substantial variable when we attempt to reconstruct basin evolution, is difficult to evaluate without this methodology. The 3D models improve our understanding of the local basin architecture, identifying similar grade characteristics at different structural levels and thus suggesting that much faulting and folding are post-mineralisation events. In addition, we identified several growth faults adjacent to thickened layers, representing two possible sedimentary depocentres. These thicker domains apparently relate to the highest Pb content. If further analysis of rocks, thickness and grade distributions support this preliminary correlation, then a syn-sedimentary model for mineralisation might be applied, and would contrast with the sub-surface model for mineralisation of Broadbent et al (1998).

Jan 1, 2003

Early in 1950 a new laboratory was set up to deal with problems in mineragraphy, petrology and metallography. This paper describes the equipment, the organisation and association of the laboratory with the various departments of the company, the work that has been done and future plans.At Mount Isa it was soon realised that the microscope would play a most important role in mineral dressing problems and aiding geological research.As early as 1928, R. J. Colony submitted a petrographic report on Black Star ore for Consolidated Limited; much later, in 1934-5 Dr. Grondijs published for Mount Isa Mines Limited a preliminary study of the Mount Isa orebody, followed by a mineragraphicinvestigation of mill products, and in 1937 a Study of Mount Isa Ores by H. GrondIjs and C. Schouten appeared in Economic Geology, for June-July. Other papers dealing with the petrology and mineragraphy of Mount Isa ores are appended at the end of the paper.The mill research metallurgical staff has endeavoured to incorporate mineragraphy in solving milling problems and determining the effectiveness of laboratory as well as examining minerals sent in by the geological department.For many years the amount of equipment available was limited and much of it was locally made or improvised. An improvised briquetting machine, and grinding and polishing lap gave moderate results in conjunction with an old, but serviceable, Leitz microscope. However, for more detailed and accurate work not possible with improvised equipment, many mineragraphic problems were sent to specialist in.

Jan 1, 1953

Many volcanoes in western Melanesia have tectonic settings and rock compositions that do not conform to conventional models of arc- trench systems. Part of the reason for this may be that in an environment of rapid tectonic change mantle source regions bear the imprint of former subduction even though subduction has now ceased. Results bearing on this concept and on other important aspects of Plelit nesian v ican ism and tectonics, were obtained in 1982-1986 from >e,:eral marine - geoscience studies in the re,,ii n

Jan 1, 1987

The introduction of many new hydraulic ally and pneumatically powered impact breakers over the past few years demonstrates the growing interest in this technique of breaking rocklike material. The most practical method yet devised to increase the blow energy range of hammer type impactors without incurring weight penalities, is to cushion the impact of the hammer on the tool. This has been achieved in one impact breaker by means of replenisible fluid cushions between the tool and the hammer, and blow energies up to 27,000 joule (20,000 ft. lbs.) have been achieved. Impact rock breaking is becoming an important alternative to the use of explosives in the mining and the construction industry. The design of impactors is discussed and manufacturers data is presented for most of the machines now available. A review of the research and mechanics of breaking rocks with impactors is presented and the benefits of high energy impactors are discussed. The relative merits of three impactor design types are explored with regard to achieving high blow energy.

Jan 1, 1978

By K Dagdelen

A vehicle proximity warning system is being developed using GPS and wireless local area networks to improve safety of off-highway trucks in open pit mines. After two an a half years of research, software development, and laboratory testing, field tests were carried out at operating limestone quarries and open pit mining operations to evaluate GPS accuracy and overall system effectiveness under rugged operating conditions. This article describes the progress made on this NIOSH funded project and discusses the GPS accuracy tests and overall system tests that were carried out during 2001 at the Morenci open pit copper mine in Arizona.

Jan 1, 2003

By Miller RJ, Eager DT, Lama RD

For safe and efficient mining operations, it is essential that environment and equipment status be monitored. A system that gives quick access to status at any given time, and also permits quick analysis of their history, is required. Such a computer based monitoring system has been installed at West Cliff Colliery.The system is based on 2 super mini computers. Three major sub-systems monitor conditions in the longwall operations, environmental conditions in the intake and return roadways, status of the underground and surface installations, and mining and transport equipment.

Jan 1, 1985

Shear strength testing of rock discontinuity surfaces has been undertaken at a considerable number of open pit gold mining operations in Western Australia, as part of geotechnical studies of pit wall stability. These mining operations are located in geological settings that are typified by highly weathered and/or chemically altered rocks that contain significant structural fabric in which accurate and representative measurement of shear strength is essential.Little of the published rock discontinuity shear test work and back-analysis of failures has been conducted on weathered discontinuity surfaces, at low normal stress levels which are comparable to Western Australian conditions. Available shear strength data are reviewed and the following aspects of shear strength testing are considered:ò the need for shear strength test work and the amount of testing required;ò review of laboratory testing methods and the quality of the results; ò presentation of the test results;ò discussion of the shear strength failure criteria; ò interpretation of the test results;ò summary of test results for a variety of rock types, degree of weathering and discontinuity surface conditions;ò a review of laboratory and field shear strength data to illustrate the amount of variability that can occur; andò a monitoring strategy is proposed to manage the uncertainty associated with discontinuity shear strength.

Jan 1, 1992

The Split Rock low grade copper prospect was discovered in 1969 by Cyprus Mines Corporation using stream geochemistry. Cyprus "Imes carried out geochemical and geophysical investigations, geological mapping, and percussion and diamond drilling, and concluded that the grade of mineralisation was too low (0.1% copper) to be of interest. In the present study, the geology was remapped and very substantial differences from the previous observations are recorded. (lineraliced acid dykes in a 1 000 foot hole drilled by Cyprus Mines had a total inter- section of almost 300 feet with an average crade of 0.4% copper. Surrounding drill holes at distances of 500 feet did not intersect +hese dykes. This group of drill holes occupies a small part of an area about 2 km by 1 km which was affected by intense quartz sericite pyrite alteration along many fractures with an associated soil copper anomaly. It may be that the quartz sericite alteraiion with feeble copper mineralisation represents hydrothermal alteration emanating `rom a mineralised intrusion of which the dykes mentioned above are off shoots.

Jan 1, 1978

By Freeman NV

The concept of an in stream analysis probe was developed at The Zinc Corporation (now Z.C. Mines) in the late 1960's and commercialised quite rapidly, by Phillips and then AMDEL, as an alternative to the established centralised systems (Courier, etc.). The developments which have taken place since that time are reviewed and current procedures and performance are described. An audit of the system, recently undertaken by AMDEL, has highlighted areas where improvements can be made. In 1988 the ISA system will become an integral part of a substantially upgraded process control system.

Jan 1, 1988

Coal geology plays an essential role in the investigation of in situ coal seam quality. Coal geology can also play an important part in laboratory studies such as coal washing and coking, and in operating plant problems.

Jan 1, 1976

By K H. Esbensen

Sampling of grain, animal feeds (solid and liquid) including important mineral mixtures in the Danish agricultural sector is subject to an ongoing investigation with the objective of improving existing (suboptimal) sampling procedures. Results from the first six months are presented here; the project will continue for two more years and will include international collaborators (Australia and Canada). The Danish authorities have instituted a system of control analysis, which contains a set of mandated sampling and analysis methods. From a preliminary survey it was concluded that in fact all of the existing sampling procedures are not optimised in the light of Pierre GyÆs Theory of Sampling (TOS).

Jan 1, 2005

P.IISTRACTThe Pacific Rim is advantaged by the uniqueness and diversity of its geological features. Why then is geology given so little regard in the education systems of the countries of this region? Not that these countries differ greatly from those in other parts of the world. Papers presented during the Precollege Geoscience Education session at the 28th International Geological Congress (28th IGC) held in Washington, July, 1989, indicated strongly that the problem is universal. There is a marked decline in interest in the Earth sciences and many nations are looking towards methods that might change this trend. Problems affecting geological education include the lack of purpose and direction, its obsolete curricula and the difficulty in attracting gifted students.The world-wide plight of geology comes at the very time when it should be fundamental to a public understanding of the global effect of human population pressure. There is a universal awareness of "the environment" but very little awareness of the science that has supplied most of the data. Geology, as the science of the Earth, is of paramount importance to an understanding of our life on this planet, particularly in its role as the source of our every need.

Jan 1, 1990

By D Sidea

There has been increased focus in Australia on large diameter raise boring for ventilation shafts and orepass excavation in good quality, brittle, highly stressed rock. As mining in many parts of Australia progresses to deeper levels, more vertical openings are being excavated in highly stressed ground conditions. However, whilst shafts have been successfully raise bored in highly stressed rock, it is often at a significantly increased risk of loss or damage to inhole equipment. It is important for both mine owners and contractors to have an appreciation of these risks at the planning and tendering phases of raise boring contracts. This paper provides an understanding of the risks associated with large diameter raise boring and a review of methods to predict failure in highly stressed rock.

Jan 1, 2005

By Harvey T, Kizil M, Bride J

Hydrogen sulphide (H2S) as a seam gas has occurred in several locations in the German Creek seam at Southern Colliery. This paper overviews the techniques developed to quantify the H2S content of the seam, overviews research into controlling and reducing H2S emissions from the seam, and details the procedures used to mine through the HZS zone in 702 longwall panel. Learning points from research and mining experience are reviewed for application in the next longwall block.

Jan 1, 1998