Search Documents

By G Harbort, D Clarke, D Morgan, C Sola

Northparkes Mines commenced production in 1994 and the mine has significant reserves to allow operation into the future. There are a number of potential future concentrator feed sources with variable sulfide mineralogy and grades.In February 2012 a comprehensive flotation survey was conducted to allow mass balancing and evaluate the operation of the flotation circuit. A rudimentary, copper element only, unsized flotation simulator was developed to evaluate high level potential for optimisation and improvement. In 2013 this flotation model was expanded to produce a mineral based, floatability component model to estimate the effect of future concentrator feed source on metallurgical performance. This revised model allows various circuit configurations to be simulated to provide a high level blueprint for the long-term planning to maximise performance.This paper provides a review of the process followed to develop the model, including an analysis into the mineral floatability component model and its calibration against plant operations. The effect of varying feed mineralogy and feed quality on future performance has allowed an internal review of potential circuit changes needed to accommodate the changing future feed.CITATION:Clarke, D, Harbort, G, Morgan, D and Sola, C, 2014. Northparkes Mines – flotation and planning for the future, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 203–208 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By U König, N Norberg

Traditionally, quality control of iron sinter has relied on time-consuming wet chemistry. However, the mineralogical composition that defines the physical properties, such as strength or reducibility, is not monitored.X-ray diffraction (XRD) analysis in combination with Rietveld quantification and statistical data evaluation using partial least squares regression (PLSR) has been successfully trialled to determine the mineralogical composition and process parameters such as the FeO (Fe2+) content and basicity of iron sinter within an analysis time of less than eight minutes per sample. The results were compared with wet chemistry data.PLSR does not require pure phases, crystal structures or complex modelling of peak shapes. The analysis is therefore easy to set up and ideal if only one property needs to be analysed. PLSR results show an accuracy for the FeO content of ±0.3 per cent for the samples analysed in this case study.Both the PLSR and Rietveld methods take the full XRD pattern into account and can be simultaneously applied on the same measurement. PLSR was found to be the more robust method if only FeO and basicity results are required. The Rietveld method helps to predict other parameters, such as the compression strength of the sinter, by monitoring all existing phases (eg larnite C2S or silico-ferrite of calcium and aluminium phases).CITATION:König, U and Norberg, N, 2015. Iron sinter process control using x-ray diffraction, in Proceedings Iron Ore 2015, pp 53–60 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

The deep seafloor in Papua New Guinea's proposed Exclusive Economic Zone appears to be a gold-rich province in the same sense as the territory above sea level. Two significant sites with polymetallic massive sulphide deposits forming today are known on neovolcanic ridges in the Manus Basin. Their high precious metal contents have led to renewed interest in the issue of exploiting seafloor mineral deposits. The prospects of finding other, possibly larger deposits in the region appear substantial. This paper reviews current data on seafloor deposits in Papua New Guinea (PNG) and raises some issues relating to future commercial exploration and mining of the sea floor. One of the known PNG deposits could become a prime candidate for the trials needed to develop technology, establish costs, and minimise environmental impact.

Jan 1, 1994

By S Padekar, C Tapia, D Likhachev, S Harlikar, D Sapkale

In the quest to access valuable critical minerals, humankind is expanding the frontier into extreme environments like space and deep-sea mining. These ambitious enterprises involve considerable costs and lengthy development cycles to ensure the robustness of mining systems in the face of the harshest conditions and unforeseen challenges. Unfortunately, obtaining information from these unexplored territories is complicated. Data is often scarce, incomplete or impossible to obtain until equipment is deployed, leaving engineers facing many uncertainties throughout the design, testing, production and preparation of such missions. Despite these challenges, these extreme environments operate under consistent physical and chemical principles that can be faithfully digitally replicated. However, unexplored areas and dynamic systems like weather and geology continue to carry uncertainties. While eliminating uncertainties remains elusive, Digital Twins offers a means of robust risk management tool. These virtual replicas can excel in simulating extreme conditions and unexpected events, helping optimise and validate mining system designs tailored for such hostile environments. This study takes inspiration from the Mars Science Laboratory (MSL) Curiosity Rover’s wheel damage rate to develop a Multiphysics Modelling and Virtual Motion Simulation (MMVMS) system. Using advanced Generative Design, this MMVMS system refines the MSL’s design, simulates component and system performance, and assesses the risk of premature damage while operating on Mars. Additionally, MMVMS integrates cutting-edge CAD design technologies from aerospace and manufacturing to realistically recreate the Martian environment and a detailed representation of MSL, allowing mobility verification and validation simulation to test different components in terms of materials, design, weight, power and, therefore, cost. The research highlights the precision of MMVMS in replicating extreme conditions, simulating and evaluating internal and external variables influencing the entire system (Rover) in real-time, and predicting movements, failures, and premature damage. This sophisticated Digital Twin technology, showcased in this research, holds promise not only for space missions but also to be adapted for terrestrial and deep-sea mining operations.

Sep 1, 2024

By J Taylor, M Smith, A Tunnadine, D Nikolakopoulos

As Olympic Dam rapidly expands into the Southern Mine Area (SMA) the Mine Geology team has concurrently ramped up underground diamond drilling to sustain rates of above 175 km/a. With >10 underground rigs double-shifting, traditional paper sections used for the management of drill programs were no longer optimal due to scale of operations. An opportunity was identified to modernise monitoring of all underground diamond drill programs, through the integration of logged copper sulfide estimates with Olympic Dam’s first-fully integrated deposit-scale geological model in Leapfrog Geo. This paper describes the transition within the Mine Geology team from reliance on 2D paper sections, towards near-real time 3D geological modelling for optimising end-of-hole decisions in the field. This transition was enabled by innovative database solutions informing locally constrained implicit models, limited by a distance buffer around active underground fan drilling. Due to the high volume of historic drilling, there were significant computational challenges with the implementation of daily production style implicit models at Olympic Dam and initial testing of regular updates to implicit gradeshells and sulfide domains required in excess of 12 hrs to run. The enabling solution was to optimise the interfaces between the AcQuire database, Deswik MDM and Leapfrog Geo to create a dynamic, streamlined workflow that was easily completed by Mine Geologists in accordance with daily production duties. Geologists are now building rapid implicit models for a range of variables from an integrated data set of logged sulfide estimates and existing assays, spatially constrained by 150 m buffers around active drilling using a unique drill fan identifier flagged during the planning phase. Once the live-implicit models are updated, they are exported for visualisation on field tablets to be used during logging and core checks at the start and end of every shift. To manage the risk of ‘going digital’ interpretation remains at the forefront of the drill section close-out process, with Mine Geologists critically reviewing the finished sections on a standardised template with new learnings wireframed and communicated to stakeholders. The Live Field Model has enabled a step-change in the geological effectiveness of diamond drilling, reducing over – and under-drilling ore-waste at Olympic Dam continuing to push drilling effectiveness towards 20 per cent of intercepts >2 per cent Cu. In addition, upside or risk identified during the proactive management of drilling execution can be rapidly capitalised or mitigated.

Mar 22, 2022

By M Armony, J F. C L Costa, J C. Koppe

Linear kriging methods fail to estimate local grades and local reserves for highly skewed variables due to three reasons: it uses only part of the available data information, it has no physical principles associated with the mathematical proceedings to minimise the problems, and it works with continuous variables while data are discrete because of the limited precision of any equipment. The techniques commonly used up to now to solve the highly skewed variables estimation problems were unsuccessful, unless mathematical rigor is abandoned. Even the method of multiple indicator kriging is not satisfactory. This paper presents a new framework, the field parametric geostatistics (FPG) that transforms noisy variograms into well-behaved variograms and justifies mathematically empirical procedures commonly used, as trimming or capping arbitrarily very high values. The method, when applied to non-skewed variables, yields similar results to classic kriging. The methodology is illustrated in a case study at a gold deposit in Brazil, and compared to results obtained by usual techniques.

Sep 26, 2011

By S Q. Zhao, J H. Wei

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Xitieshan lead-zinc deposit is located in the north margin of the Qaidam Basin, Qinghai Province, China. It is one of the largest massive sulfide deposits in China and is supposed to be of the sedimentation-exhalation (SEDEX) type. Based on the main ore mineral and sulfur isotopic compositions in sulfides found in the wall rock, the S of the deposit is considered to originate from the mantle, but the fluid potentially mixed with sea water during the hydrothermal circulation exchange. The study of lead isotopes shows that the metallogenic material is characterised by the mixture of orogenic and upper crust sources. The lead isotopic signature of the wall rock is similar to that of the ore, which shows synsedimentary characteristics. According to the composition of the rubidium and strontium isotopic signature, the value of 87Sr/86Sr is lower than the average value of that in the crustal rock, which is larger than that of the mantle. Hence, the metallogenic materials of this deposit mainly originate from the crust, which is related to materials of volcanic rocks activation and migration of the deep hot circulating water. The process of the metallogenic fluid circulation shows continuous interaction with crustal material and lead to continuous enrichment of the ore forming fluids. From the study of the fluid inclusion microthermometry of the ore and the associated minerals combined with the C, H-O, Si isotopes, it is believed that the metallogenic fluid is mainly coming from the mantle or the deep magma chambers. The rising deep fluid then mixes with the sea water. The carbon dioxide escaping and mixing with sea water during the hydrothermal exhalation process leads to the rapid precipitation of the hydrothermal fluid to deposit metal. That is proposed as the principal formation mechanism of the Xitieshan deposit. Further studies are proposed, including obtaining geochronology data from this deposit.CITATION:Zhao, Z X, Wei, J H, Liang, S N and Zhao, S Q, 2015. Advances in research on metallogenic mechanisms for the Xitieshan sedimentation-exhalation lead-zinc deposit, Qinghai Province, China, in Proceedings PACRIM 2015 Congress, pp 487–494 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By C R. Fountain, W R. Cannings

The zinc-lead-silver mineral resource at Lady Loretta ranks amongst the worldÆs richest when measured in terms of in situ metal grades. However, the project remains undeveloped 28 years after its discovery in 1969. The primary obstacle to development has been the fine and complex grain structure of its ores, which make flotation concentration inefficient even with fine grinding. The size and remote location of the deposit have also hindered exploitation. BUKA planned to directly fume the volatile target metals from the ore when it acquired the project. Intensive, post-acquisition modeling showed the innovative processing route to be uneconomic, notwithstanding high metals recovery and low waste content in fume product. Progressive modifications and supplements to the underlying fuming process enhanced economics and resulted in a new mine-to-metal processing route for zinc-lead-silver ores. The proprietary, three-stage BUKA Zinc Process offers technical, economic and environmental advantages. It is expected to find widespread application in the treatment of ores and residues. However, neither continued R&D nor application to Lady LorettaÆs currently delineated resource can be justified under prevailing market conditions. The objectives and results of each step in the process development sequence are outlined with reference to their impact on the commercial viability of the Lady Loretta project.

Jan 1, 1998

By Grady B. V, Ault A. R, Newman O. M G, Fraser R. J, Malcolm J. McPhersqn

In all electrolytic zinc plants cadmium is removed as an impurity prior to the zinc electrowinning stage of the process. Cadmium metal is the favoured form of this by-product and most plants use an electrolytic route for its production. The formation of dendrites in cadmium electrowinning processes is the major limitation to deposition rates. There is an economic incentive, therefore, to better understand the factors affecting their growth. A technique that has been used by others to examine fundamental aspects of dendrite growth has been applied to industrial strength electrolytes. It involves potentiostatic deposition in a cell containing the electrolyte of interest. The variation in the current with time at a given overpotential allows the determination of the dendritic growth induction time. A method was developed (the Locus method) from the investigation of a set of such potentiostatic curves, obtained over a range of applied overpotentials, that appears to give a measure of electrolyte quality with respect to dendritic growth in galvanostatic deposition. The Locus technique predicts that zinc at industrial concentrations in cadmium electrolytes should have a significant effect on morphology and that deterioration of morphology will occur as the zinc concentration in the electrolyte is increased. This effect is consistent with literature prediction and was shown to relate to a reduction of the diffusion limiting current density. Magnafloc R333 is used as an additive at Pasminco Metals-EZ to control the morphology of cadmium deposits and the Locus method was successful in predicting its dendrite inhibiting properties. A possible mechanism is discussed. This work has opened avenues for future research with respect to a technique that may have an industrial application in electrolyte characterisation and has pointed to a direction in which better understanding of galvanostatic dendritic growth may be found.

Jan 1, 1993

By J Northfield, L Neesham

The GRE46 Underground Project lies beneath the environmentally unique and culturally endowed shore of Lake Cowal. The ore body is open both along strike and at depth and is currently defined to a strike length of 1.5km and depth of 800m. The Warraga exploration decline commenced in March 2019 and represents the first stage of the Project, which is expected to underpin production at Cowal Gold Operations (CGO) for a period exceeding 10 years. Mining operations at Cowal commenced in 2005, following a period of over 20 years of exploration and permitting. In 2015 Evolution Mining (Cowal) Pty Limited (Evolution) acquired the operation from Barrick Gold Ltd (“Barrick”). Barrick had a life of mine plan that anticipated a cessation of operations in 2024 at a processing rate not exceeding 7.5 Mtpa. Evolution have grown the regional endowment considerably and have a currently approved mine life out to 2032 with a currently approved maximum processing rate of 9.8 Mtpa. This paper examines the history, current status and future path of one part of that plan, the GRE-46 Underground Project. Topics for discussion include discovery, Mineral Resource growth under different ownership philosophies, planning, permitting and commissioning of an exploration decline and bulk sampling project, and integration with the possible future mine. Environmental sensitivities affecting regulatory approvals, timeframes, technical challenges, opportunities and solutions are discussed, along with the path required to fast-track production from the existing 14Mt, 1.4Moz Mineral Resource while complying with the requirements of modern, responsible project development stewardship.

Mar 15, 2021

By A A. Puhalovich

The placement of chemically reactive mine wastes in mined out pits (æpit backfillingÆ) is increasingly seen by industry as best practice to manage long-term environmental risks. This is primarily because leaving wastes at the surface, or allowing pit lakes to develop, can result in unacceptable environmental risks. The costs and practicality of mitigation options such as installation of covers and community expectations of landform re-construction to achieve a post-mining, beneficial land use are also important drivers for pit backfilling.Pit backfilling can significantly reduce the post-closure risks to receiving environments, by minimising seepage due to tailings, acid/solute generating waste rock and/or salts derived from mine water treatment. Environmental risks are often highest where wastes are located close to the ground surface, due to relatively high rates of groundwater movement in near-surface aquifers and/or failure of engineered structures due to rainfall/erosion processes. Placement of these wastes at significant depth in pits, subject to mine planning and environmental assessment, can address these risks by increasing the path length and resistance from contaminant source to receptor, thus enhancing encapsulation of the wastes.Pit backfilling can also be cost-effective for mining companies. This is because existing pits are developed on the basis of an economic return and thus provide an opportunity to store tailings in an existing æengineered structureÆ at little or no incremental cost when compared with building and operating a new tailings or waste rock storage facility, often encompassing complex cover/drainage management systems. Key issues for consideration are mine planning, the long-term geotechnical behaviour of the wastes (eg consolidation of tailings which leads to release of acid/solutes in tailings porewaters), seepage rates to downstream receptors/agreed end point criteria and potential resource sterilisation. Internationally, mine closure guidelines are also showing a greater recognition of pit backfilling in the context of allowing mining companies to meet agreed post-closure land use objectives.In summary, pit backfilling can enhance the encapsulation of chemically reactive mine wastes and environment protection, and with agreement on post-closure beneficial land use, can also help to deliver post-closure benefits to communities.CITATION:Puhalovich, A A, 2012. Pit backfilling - Managing chemically reactive mine wastes and achieving rehabilitation objectives, in Proceedings Life-of-Mine 2012 , pp 279-286 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By D J. Williams, S Islam

Worldwide production of black coal amounts to about 8 billion tonnes. Perhaps 20% of this annual production is washed to improve its quality, generating perhaps 250 million tonnes of coal tailings annually, generally in the form of a slurry. The coal tailings slurry is typically thickened to about 25% solids by mass prior to disposal to a tailings storage facility (TSF), and hence comprise mostly water (about 85% by volume), plus sand, silt and clay-sized mineral particles and carbonaceous material. While the tailings settle and consolidate on deposition in the storage facility, their high moisture content makes them prone to run-out should the tailings dam fail, and makes rehabilitation of the tailings difficult. Hence, it is important to understand the consolidation and shear strength of coal tailings. Laboratory consolidation testing of coal tailings from a slurry to a soil-like state has been carried out in a purpose-built, large-scale, slurry consolidometer, instrumented with load cells and pore water pressure (PWP) transducers. Laboratory vane shear testing of coal tailings produced at different gravimetric moisture contents has also been carried out. The test results have allowed a regression model to be developed relating the peak vane shear strength of the coal tailings to their gravimetric moisture content.CITATION:Islam, S and Williams, D J, 2018. Consolidation and shear strength of coal tailings slurries, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 62–71 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By R J. Soriano, S Ciutina

The Masbate gold deposits are situated on the island of Masbate, 350 km south of Manila. A new plant was commissioned in April 2009. The grinding circuit consists of one semi-autogenous (SAG) mill Ø9.75 m × 4.27 m, two ball mills Ø5.6 m × 7.1 m and a pebble crushing circuit, which is usually called a SAG-ball mill-crusher configuration. The SAG mill was originally equipped with radial pulp lifters. The mill runs at fixed speed of 10.9 rev/min, which is approximately 80 per cent of critical speed (per cent CS). Due to the high speed of the mill the original radial design pulp lifters presented a high volume of recirculating load inside the chamber and consequently heavy wear on the outer circle (bottom pan).In order to address the high wear on the pulp lifters a number of avenues were considered in early 2011. The chosen solution was to change the geometry of pulp lifters from radial to curved design. The pre-existing drilling pattern on the discharge end of the mill was a major constraint. A number of designs were considered. The selection of the most suitable option was to be made based on 3D discrete element modelling (DEM) and smoothed particle hydrodynamic (SPH) simulations.The original radial design and two potential solutions for curved pulp lifters were simulated with 3D DEM and SPH software. The main three objectives were predicting the charge dynamics, the expected wear patterns and discharge efficiency. One of the solutions was chosen and implemented during 2012.Observations carried on after installation of the curved pulp lifters have confirmed, as expected, a reduction in wear intensity on the outer pulp lifters. In addition to this, at early stages of operation with curved pulp lifters, the mill operator noticed a reduction in energy consumed by the mill with no detrimental effect on mill performance.This paper is intended to further study the effect of curved pulp lifters on mill energy consumption.CITATION:Ciutina, S and Soriano, R J, 2014. Curved pulp lifters – can they save energy?, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 109–116 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By P Navarra, R Kuhne

Dynamic simulation (discrete event simulation) is the preferred methodology to evaluate the impact of dynamic aspects of processing plants on the overall plant capacity. This tool can be used to: identify bottlenecks in the plant,justify upgrade and expansion projects by evaluating their impact, oroptimise maintenance and operating practices without disrupting the operation. Iron Ore Company of Canada's (IOC) pelletising plant is a complex operation because of multiple products, varying equipment capacity and shifting bottlenecks. Furthermore, with extensive capital requirements for projects and long lead times, a high level of confidence in project outcome is required. Therefore, a model of IOC's pelletising plant in Labrador City was constructed in 2007 by a joint IOC and Hatch team. The model includes both operational and metallurgical aspects in order to better capture the complexity of IOC operation. In this paper, the justification, boundaries, and functionality of the model are described. A comparison of simulation results to historical plant operation is given. It is observed that projects have interactions and that the benefits of combined projects are not equal to the combined benefits of the individual projects. Projects can have synergies that result in greater benefits when combined or can have overlapping benefits that result in lower benefits when combined. The power of the proposed modeling exercise lies in the ability to assess the impact of projects on overall performance.

Jan 1, 2009

By S Basu, S L. A Gowravaram

CaF2 has been a common constituent in a wide variety of welding fluxes, including those used for submerged arc welding (SAW). The widespread use of CaF2 stems from its role in lowering the liquidus temperature as well as the viscosity of the molten slag that covers the weld pool. However, the harmful effect of fluoride evaporation from molten flux, on the environment as well as the health of the users is becoming increasingly evident over the years. This has led to increasing attention towards reducing the CaF2 concentration in the fluxes. The fluoride-free formulations face the challenging requirement to maintain the thermo-physical properties (viscosity, liquidus temperature etc) like those observed in fluoride-containing fluxes. In the present work, three fluxes with compositions in the CaO-MnO-SiO2-Al2O3 system have been identified as promising alternatives to the CaF2-rich fluxes. However, the thermo-physical properties of any such flux need to be comparable to CaF2-based commercial SAW fluxes before it can be adopted for regular use. The single hot thermocouple technique (SHTT) has been used by several researchers in the past as a tool for observing the melting and solidification characteristics of fluxes. This device has been developed in the present work and is used to characterise the melting behaviour of the fluxes. The measured solidus and liquidus temperatures from SHTT were compared with the results from differential thermal analysis (DTA) and simulations using the FactSage™ software for a comprehensive understanding. In spite of having a slight deviation in the measured values from the multiple techniques, the results obtained from these multiple methods show that the selected compositions could be potential CaF2 free alternative welding fluxes.

Jun 19, 2024

By M F. Gazley

The amphibolite-facies metabasaltic rocks of the Mine Mafic Package at Plutonic Gold Mine, Marymia Inlier, Western Australia, contain an estimated total endowment of 12.2 Moz of Au, which includes 4.71 Moz of past production and 2.77 Moz of reserves and resources; the remainder comprises lower-grade inventory. Over 65?000 multi-element analyses of whole-rock core and face channel samples from the underground workings of the deposit have been collected by portable X-ray fluorescence (pXRF) using a handheld Innov-X Omega pXRF unit. The analyses were performed on pulverised samples through paper bags, and were corrected using a pulverised, matrix-matched, reference standard. This method of data correction compares favourably with conventional XRF analyses performed on the same samples.A preliminary study based on pXRF analyses from a small number of drill holes found that a geochemical stratigraphy was evident in the pXRF data, and that this stratigraphy strongly controlled the location of Au mineralisation. The present study incorporates a much larger pXRF data set that samples a greater volume of diamond drill core and face channel samples and presents the data in a three-dimensional (3D) framework.This data set allows an investigation of the mineralogy of Au mineralisation with varying geochemical associations across the deposit. Historically, there has been a strong relationship identified between As and Au, which has caused issues with metallurgical performance, rendering some areas of the deposit only marginally economic. Utilising seamless data integration of the pXRF data set allows for recognition of the different styles of Au mineralisation using elemental concentrations and ratios from the multi-element analyses (Au:As, Au:As:Cu, As:Cu vs. K:V), and to visualise the distribution of these different mineralogical associations in 3D. The results of the 3D modelling and geochemical characterisation of the different styles of Au mineralisation are currently the focus of an extensive metallurgical testing program, the preliminary results of which are presented here.

Aug 22, 2011

By D Lalor, N Goodman

The increasing demand for batteries is resulting in the development of large-scale projects for the production of key battery metals such as nickel and vanadium. Several of these projects plan to extract the battery metals from the ore via chemical roasting, leaving large volumes of waste iron oxides after fuming and/or leaching of the battery metals. These iron oxide wastes can be smelted in a HIsmelt furnace using biochar as the reductant, to produce clean, green pig iron with net zero carbon emissions. This green pig iron can then be added to basic oxygen or electric arc steelmaking furnaces to produce green, net zero carbon, steel. This paper describes the flow sheets and the economics for potential projects producing green pig iron via HIsmelt using waste iron oxides from nickel and vanadium production plants.

Sep 18, 2023

By D Bradshaw, R Dunne, S Farrokhpay

It is well known that clays affect the flotation performance, and many of the refractory gold ores around the world contain clay minerals. Therefore, an ore sample from the Carlin Trend was selected for this study as these ores contain large quantities of clays. The presence of clay minerals in an ore makes it susceptible to a range of variables, such as the solution chemistry determined by pH and the chemistry of the rheology modifiers. The viscosity of the ore slurry was measured as a function of solid concentration and particle size distribution, in addition to using different rheology modifiers and pH regulators. The results were correlated with the ore flotation performance. It was found that various reagents known commonly as dispersants or rheology modifiers have different effects on the ore slurry viscosity. This study revealed that the gold flotation recovery can be improved by changing the pulp rheology.CITATION:Farrokhpay, S, Bradshaw, D and Dunne, R, 2013. Rheological investigation of the flotation performance of a high clay containing gold ore from Carlin Trend, in Proceedings World Gold 2013, pp 333-340 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By K Williams, T Donohue, W Chen, T Roessler, A Katterfeld

Wet sticky iron ore poses particular difficulties in every aspect of the material handling process. Material hang-ups in bins, pipes and chutes; carry-back and spillage due to insufficient belt cleaning; clogging of screens; malfunctioning of crushers as well as rat holing of gravity reclaimed stockpiles are all predominantly due to the inherent cohesion and adhesion characteristics of the wet, sticky ore (Roberts, 1993). Limited understanding and quantitative measures on the stickiness of such a material significantly lower the mining operation efficiency.This research aims to investigate the cohesion and adhesion characteristics of the wet, sticky ore on physical modelling, experimental techniques and numerical implementation. Initially, the suitable bridging mechanism that contributes to the cohesive and adhesive forces within the iron ore material was identified (Hering, Martin and Stohrer, 1989; Rumpf, 1958). A cohesion/adhesion energy density factor based contact model was then introduced to describe the stickiness of the material. Secondly, an experimental system was proposed to directly test the stickiness of the material. Such a system is able to obtain both the cohesive/adhesive shear force and tensile force of the material at a specific moisture content. Lastly, the implementation of the proposed cohesion/adhesion model into the discrete element modelling (DEM) software was also discussed. A cohesion/adhesion calibration for modelling wet sticky iron ore in DEM was then conducted to ensure the material modelled in the simulation is reflective of the reality.From the study, understanding of the cohesion/adhesion characteristics of the wet iron ore material is significantly enhanced. Experimental and numerical outcomes can be directly applied for better designing or optimising the material handling processes that involve wet sticky iron ore. Consequently, the mining operating costs can be greatly reduced.CITATION:Chen, W, Donohue, T, Williams, K, Katterfeld, A and Roessler, T, 2015. Modelling cohesion and adhesion of wet, sticky iron ores in discrete element modelling for material handling processes, in Proceedings Iron Ore 2015, pp 387–392 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

The completion of the Hot Strip Mill at the Port Kembla works of Australian Iron & Steel Ltd., makes possible the production of steel plates and wide strip of a quality and in quantities not possible previously in Australia, and will also enable the production of tinplate to be undertaken in this country.The site chosen for the mill was a mud fiat underlain by a hard stone bottom at 5, to 801 feet below the surface; and a total area of one hundred acres was reclaimed to a level of 20 feet above the original surface.Three adjoining buildings were constructed to house the slab receiving yard, mill equipment and electric drive, together with the plate finishing line.After slabs have been heated to 2250°F at a rate of 90 tons per hour, they are transferred to the vertical scale breaker which is the first stand in the hot roughing mill. Here the primary furnace scale is first cracked and then blasted off by high velocity water descaling sprays.The next stand is the horizontal scale l;Jreaker, where any remaining primary scale is broken and then blasted off. After descaling, the slabs pass to the broadside mill, where short slabs are turned and rolled on broad side for wide plate.The next step is a slab squeezer which squares up the edges after broadsiding ready for the reversing mill. This is the finishing stand for plate and the last roughing stand for strip, which then passes to the finishing mill.The hot strip finishing mill consists of six stands with a maximum finishing speed of 2,230 feet per minute. Strip is cooled for coiling by water sprays on a hot run table and then coiled on a mandrel type downcoiler, from whence coils of hot strip are weighed and transferred by conveyor to the coil storage building.Plates are transferred from the reversing mill to the plate finishing line where operations consist of levelling, inspection, branding, cutting to width and length:INTRODUCTIONDue'to the increasing production of cars, refrigerators, washing machines and similar consumer goods in Australia, together with the increased requirements of galvanised iron...

Jan 1, 1956