Search Documents

By Gordon G. Bentle, W. P. Fishel

GREINER, Marsh, and Stoughton1 have reviewed the literature in a monograph on the iron-silicon system. The lack of agreement among the various studies may be due to the difference in the purity of materials in some cases. The results of the X-ray method indicate only a general rather than a specific limit of the y loop. The iron-titanium system was investigated by Roe and Fishel,' whose results are used in determining the iron-silicon-titanium y loop. The literature indicates that no study has been made thus far of the iron-silicon-titanium system in the y loop region. Experimental Procedure The alloys were made from Armco iron, 99.86 pct Si, and 98.5 pct Ti. The titanium contains 1.07 pct Fe. The Armco iron contains 0.01 pct C, 0.005 pct Si, 0.02 pct Mn, 0.006 pct P, 0.01 pct S, and 0.04 pct Cu. A dilatation sample of Armco iron was prepared in the same manner as were the other samples. Several dilatation runs indicated that Ac3 begins at 905°C and ends at 910°C, which compares favorably with the study of Wells, Ackley, and Mehl' employing specially purified iron. All alloys were melted in an induction furnace in Alundum crucibles and were top poured into baked core sand molds. The ingots weighed about 600 g as cast. Dilatation samples of 4 in. by % in. diam were taken from the bottom end of the ingot, from which turnings for analysis were taken. Turnings from each end of two of the samples indicated that the alloys possessed uniform silicon content. A hole was drilled halfway through each end of a 4 in, dilatation sample. A chromel-alumel thermocouple was inserted in each hole and the surrounding metal peened in to hold the thermocouple in place. Fig. 1 represents the dilatation apparatus. The heating unit is an Alundum tube wound with resistance wire; the dilatation tube is a McDanel combustion tube; the push rod is zircon; the dial gage is graduated in 0.0001 in. and was vibrated to prevent sticking. A blank run over the temperature range of interest gave no significant dilatation. The thermocouples were attached to a multiple recording micromax which indicated the temperature at each end of the sample at 35 sec intervals. A Lindberg control unit governed the rate of heating of the furnace, and lowering or raising the

Jan 1, 1957

By H. Cecil Spicer

The results described in this article are based on field work conducted during the periods APril-May, 1939, and MaY-JulY, 1940. The United States Potash CO. is mining potash on Government land under a permit from the Department of the Interior and the geophysical investigation mas completed under a cooperative arrangemerit made between that company and the Conservation Branch of the Geological Survey. The writer, a member of the Section of Chemistry and Physics of the Geologic Branch, was assigned to this investigation. Four definite objectives were in mind for the geophysical work in the studies over the salt deposits. The first was to determine the measure of success that could be attained in this type of work with the resistivity methods that were to be employed. These methods had been introduced into the work of the Conservation Branch by Benjamin E. Jones for the investigation of dam sites, and have been used under his direction by the author for such work. If the method proved to be applicable, an l was to be made to contour the top of the salt beds and also the other formation boundaries known to be present in this area. Salt-water aquifers were to be studied in an effort to determine their boundaries, and an attempt was to be made to delineate the potash-bearing beds. Others have made, and reported, resistivity studies over saliferous deposits in different areas. Friedell and Messrs. Schlumberger2 reported geophysical work performed in the disrovery of the salt domes of Alsace; Carrette and Kelly3 described the geology of the same area. Leonardon and Kelly4 published a resistivity curve obtained over the Hettenschlag dome, and a further discussion of this same area was given by the Messrs. Schlum-berger5 in a communication. Messrs. Alty6 described studies 0" salt deposits in which the sing[e-probe method was used. Sinerez7 mentions that electrical methods were tried over salt deposits in Spain. Geoffrey and Charrin8 show a resistivity curve obtained over marl, gypsiferous marl and salt which is similar to that obtained over the New Mexico salt deposits. Kelly9 reported resistivity work performetl with the ground comparator of Zuschlag over the salt deposits near Syracuse, N. Y., where the Salina formation is at a depth of 700 to 800 ft. Some structural studies on the potash basin of Alsace are described by Poldini.10 Another single-probe resistivity study, made over salt deposits in New Mexico, is briefly described by Heiland,ll through the courtesy of Harry Aurand, of the Midwest Refining CO.

Jan 1, 1942

By Edward Saibel

THE various theories that have been advanced to explain or predict the conditions under which a metal fractures may be divided into two categories: First, there are the macroscopic theories generally used in engineering practice. These are empirical in nature and limited in application. For example, the maximum normal stress criterion, which is quite satisfactory for a mild steel in simple tension at atmospheric pressure, no longer suffices when this steel is pulled under hydrostatic pressure.2 In all of these empirical theories, the critical condition characteristic of the material and of the loading conditions must be obtained experimentally. Secondly, there are the theories based on interatomic forces,3,4 or on the energy required to form new surface.5,6 These have all dealt with the theoretical evaluation of the tensile stress necessary to bring about rupture in a purely brittle manner; that is, without plastic flow preceding fracture. All of these attempts have led to values of the tensile strength of crystals or of polycrystalline bodies that are 100 to 1000 times higher than observed values. On this account, it has been thought necessary by some investigators to conceive of a microcrack structure or distribution of flaws throughout the specimen such that the resulting stress concentrations provide the factor necessary to bring about agreement between calculation and experiment. It has been pointed out by several observers7 that this point of view is highly unrealistic, in that the weakening effect of these flaws or microstructures must be very uniform from specimen to specimen, since the fracture stresses found for various specimens of the same material tested under similar conditions are so - nearly constant. Furthermore, since calculations based on atomic forces or atomic energy are for purely brittle fracture, a condition probably never satisfied in tests, agreement is hardly to be expected. Thermodynamic Theory Of Fürth In order to resolve this apparent discrepancy between the theoretical cohesive strengths and the observed fracture strengths, Fürth8 advanced a thermo- dynamic theory of the tensile strength of isotropic bodies based on work of Born9 relating to the melting of crystals. Assuming an isotropic material free from imperfections and flaws, behaving elastically up to the breaking point, and assuming a connection between rupture and the melt- ing phenomenon, Fürth obtains an expression for the rupture stress u, in the form [ ] where Q is the melting energy per unit mass, ? is the density, and µ is Poissons’ ratio. Fürth compares fracture stresses computed from Eq I with the fracture stresses of metals as given in the Landolt-Bernstein Tables (1927) and in the Hand-

Jan 1, 1947

By L. A. Willey

Although the interierometric method for the determination of length changes was devised by Fizeau more than three quarters of a century ago, it has not achieved the widespread use in the metallurgical field that its precision and simplicity would seem to warrant. The interferometer and the basic principle are both very simple. When optically plane surfaces held at a very slight angle to each other are illuminated by monochromatic light, rectilinear, equally spaced interference fringes arc formed. Each fringe corresponds to a defiuitc thikness of the wedge formed by the optical flat.;. The difference in wedge thickness between two consecutive fringes is cqual to one half the wave length of the illuminating light. Instruments for vicwing the intertero~ncter have passed through a number of modifications. Outstanding among the improvements were those Abbe. in 1884. His improved instrument permitted micrometric mcasurements to the order of one-hundredth of the width of an interference fringe (i.e., lengths were measured to the order of one two-hulldredth of the mave length of light ). It also permitted the consecutive use of light of several wave lengths. which made possible the determination of the order number of any fringe and therefore the absolute thickness of the wedge at any point. The Abbe dilatometer and methods of measuretment, including corrections to he applied for the change of index of refraction with change in tempcrature and barometric pressure in an air wedge, have been thoroughly described by Pulfrich.' Pulfrich2 made further improvements in the interference measuring apparatus. His instrument embodied all the features of the Abbe dilatometer but was made more versatile by its complete mechanical separation from the interferorneter. The introduction of an Amici prism in the piece permitted the simultaneous observ tion of the whole set of fringe systems developed in the interferometer from the visible light of a geisler tulle. .Also, the introduction of a direct-vision, reflecting prism made it possible to set the fringes parallel to the two vertical fiducial line. of the instrument without the necessity of rotating the interierometcr. Interferometric methods employed ill this country have been developed and dcscribed by Priest, Pelers and Cragoe," Austin,5 Merritt,= Saunders,? and Nix and MaNair. Since none of these authors used the type of instrument that was employed in the present investigation, they Will not be discussed here. This paper will be limited to the description of the interfernmetric apparatus and method used at the Aluminum Research Laboratories and to the presentation of data so obtained. Apparatus and Procedure A general view of the dilatometer, not including equipment for controlling and

Jan 1, 1945

By Allan Martin, R. A. Swalin

Diffusion rates of manganese, aluminum, titanium, and tungsten in nickel were measured at temperatures between 1100° and 1300°C. Activation energies, Q, and values of the frequency factor, Do, were calculated for each system. Values of Q were found to be within 15 pet of that for self-diffusion of nickel in agreement with present theories of diffusion. ONE of the most interesting problems in diffusion concerns factors governing the order of diffusion coefficients of various solutes in a common solvent metal at low solute concentrations. An early suggestion by Rhines and Mehl' was that diffusion coefficients might each approach that of the self-diffusion coefficient of the solvent itself. Later Thomas and Birchenall' pointed out correlations between the order of the diffusion coefficients and the freezing point depressions of the solvent by the various solutes. Other correlations have been sought. To settle this question it seems likely that much more data will be needed and, in particular, data collected at low solute concentrations. This type can be obtained by special analytical techniques as well as by use of radioactive tracers. The following study was made of diffusion of manganese, aluminum, titanium, and tungsten in a common solvent, nickel, at relatively low solute concentrations: 1—Production of alloys of nickel with manganese, aluminum, titanium. and tungsten at concentrations of the order of 1 atomic pet. 2—Use of pressure-welded diffusion couples in cylindrical form. 3—Diffusion anneals in the temperature range of 1100" to 1300°C. 4—Lathe sectioning of the diffused couples. 5—Spectrophotometric analyses of lathe turnings for the solute being studied. 6—Calculation of the diffusion coefficient for each of the solutes as a function of temperature. 7—Interpretation of results with current theories of diffusion. Experimental Work Materials—Two types of nickel were used in this research. The grade designated as Vacuum melted Mond nickel was used for all diffusion systems except the Mn-Ni system for which the Vacuum melted electrolytic nickel was used. Analyses of the two grades are given in Table I. The manganese used in making alloys was 99.9 + pet pure, aluminum 99.99 pet pure, titanium 99.9 pet pure, and tungsten of C.P. grade powder. Alloys used in this investigation were prepared by melting in vacuo or under a low pressure of argon. After melting, all heats except those of nickel-manganese were poured into a cylindrical copper mold 3 in. long and 1 in. ID. In the case of nickel-manganese, the alloys were solidified in the melting crucible. For nickel-aluminum heats alumina crucibles were used and for all other heats, zirconia crucibles.

Jan 1, 1957

By Ernest G. Enck

"The Rockets' Red Glare" of the Fourth of July is produced by strontium compounds. However, strontium has a number of less spectacular uses; i.e. in, or in connection with, the manufacture of ceramics, caustic soda, glass, railway and truck signal flares, beet sugar and steel. The principal ore of strontium for use both as the mineral and for production of compounds is celestite (SrSO4). This mineral varies in color from white to pink or blue depending on presence of impurities. It has a hardness of about 3.5 and specific gravity of 3.9. It is brittle and has perfect basal and prismatic cleavages. The high grade ore is obtained from England, hence it has become the standard for all other producing areas. (See analyses, Table 1.) The most objectionable impurity in English celestite is iron, coming mostly from adhering clay. On the other hand, Mexican celestite, while no higher in strontium sulfate content, is extremely low in iron (less than 0.2 pct), hence it is more desirable for certain uses. Most of the celestite in Spain and in the United States is high in calcium and barium, and commonly high in iron, and requires some form of beneficiation in order to be equal to English ore. The natural carbonate (SrCO3), or strontianite, is less important than celestite as a source of strontium, because it is less abundant and is not so widespread in its occurrence. Furthermore, it generally occurs with calcite (CaCO3) and lead sulfide (PbS), and for most uses these impurities are detrimental. This mineral is generally white or yellowish, forming needle-like crystals. It has a hardness of about 3.7 and a specific gravity of 3.68-3.8. The mineral is brittle and has an imperfect cleavage. A typical analysis of German strontianite is shown in Table 1. [ ] Distribution of Deposits UNITED STATES Occurrences of strontium minerals are known in Arkansas, Arizona, California, Illinois, Ohio, Pennsylvania, Tennessee, Texas, and Washington. Celestite occurs in the Vulture Mountains, Maricopa County, Arizona in beds three to ten feet thick associated with sandstone, gypsum, and barite. Because of the low strontium content, approximately 86 pct SrSO4, it has no commercial value. A large deposit of celestite occurs in San Bernardino County, California, in the Cady Mountains near Argus Station, about eight miles west of Ludlow. The celestite here is interbedded with shaly and clayey tuff in a zone about 300 ft thick. Massive, finely crystalline ore has been recovered with an analysis

Jan 1, 1960

By R. L. Sandefur

Professor Kim's excellent review article1 on ultimate pit planning contains a statement of the apparently widely held but incorrect belief that "kriging provides information on the confidence limits around the estimate which no other extension technique is capable of supplying." If a geostatistical approach is valid, there are several good reasons for using kriging but uniquely provided confidence limits is not among them. If kriging is possible, then confidence limits can be calculated for any other linear estimate. Kriging is the procedure which finds the weighing coefficients which minimize the estimation variance [ ] is the variance of blocks like the one being estimated. wi is the covariance of the estimated block and the i-th sample. oij is the covariance of the i-th sample and the j-th sample. Ai is the weighing coefficient for the i-th sample. N is the number of samples. The formula for estimation variance can also be used to calculate confidence limits on blocks estimated by any linear combination of sample grades including: 1) Polygons a. Hole nearest block centroid is assigned weight 1. All other holes are assigned weight 0. b. Polygonal area weighing. The samples are assigned weights directly proportional to their polygonal areas of influence within the block. The weights sum to 1. 2) Inverse distance weighing. The samples are assigned weights directly proportional to the reciprocal of their distance to some power from the block centriod. The weights sum to 1. Often only holes nearer than a certain distance and/or the nearest hole in each octant is considered. If there is an antisotropy to the ore body, an elliptical transformation often gives more accurate results. The most popular inverse distance weighing function is inverse squared distances (IDS). 3) Simple average. All samples within a certain distance are assigned the same weights which sum to 1. As an example of the applicability of the above formula to any linear estimate an internal verification on copper grade of 665 blast holes on the 1040 bench at Utah's Island Copper mine is presented. Internal verification is simple and applicable to non-linear estimates as well. Any sample (drill hole, bulk, trench, or chip) is dropped out, the value of the dropped sample estimated and compared with the actual value. If this is done for all samples, a measure of confidence limits is obtained. Internal verification is used in Cominco's MEPS system4 and in the BLUEPACK system.5 Comparison of block values against estimates697 is not dissimilar to internal verification. Results of the internal verification are presented below:

Jan 1, 1980

By W. L. Phillips

Stress-strain data are reported for sodium chloride, lithium fluoride, and magnesium oxide tested in compression at diffevent strain rates in the telrlperature range from 70° to 873°K. Quantitative equations are given for the stvain-rate dependence of the critical resolved shear stress and the initial rate of work havdening. The properties so determined are compared with results previously reported for metals. ALTHOUGH the effects of strain rate and temperature on the stress-strain characteristics of metals have been extensively investigated1,2 these effects have not been studied in detail in ionic crystals. In the only previous investigations on the effect of strain rate on the deformation of ionic crystals. Gilman and gohnston3 and Hulse and pask4 have shown that the yield stress of lithium fluoride and magnesium oxide at room temperature is proportional to the ninth or tenth root of the strain rate. CRYSTAL PREPARATION Lithium fluoride, sodium chloride. and magnesium oxide single crystals were purchased from the Har-shaw Chemical Co. The compression fixture and sample preparation have been described in detail previously.5 The detectable impurities in MgO were eight parts in 105 of Fe and six parts in 105 of Si; in LiF, six parts in 105 of Mg; and in NaC1, two parts in 105 of Fe and four parts in 10&apos; of Mg. The cleaved samples measured - 0.1 in. by 0.1 in. by 0.3 in. Prior to testing all samples were annealed at -0.8 of their melting point and cooled to room tempera- ture at 50 C per hr.&apos; Samples were strained at rates (<) of 0.1, 0.01, 0.002, and 0.0002 in. per in. per min. EXPERIMENTAL RESULTS Fig. 1 is a plot of the critical resolved shear stress a,. (extrapolation of slope of easy glide region to zero strain) of sodium chloride, lithium fluoride, and magnesium oxide tested at different strain rates as a function of temperature. In all crystals at all strain rates a, decreases with increasing temperature according to an equation of the type397 where uo is a stress constant, K is a constant, and T is the absolute temperature. The points in Fig. 1 are the average of six tests. It is evident that there is a break in the log 0,- temperature plots at a characteristic temperature T,. The constant K of Eq. [I] is dependent on strain rate, Fig. 2. The relationship

Jan 1, 1962

HenRy Clay FRick, a pioneer in modern coke and steel industry and, in more recent years, one of the outstanding financiers of America, died on Dec. 2, 1919, at his home on Fifth Avenue, New York. Although he had been ill since election day, when he had an attack of indigestion which developed into ptomaine poisoning, his death was a surprise to all. He is survived by his widow, Adelaide Howard Childs Frick; a son, Childs Frick, one unmarried daughter, Helen C. Frick, and four grandchildren. A quiet funeral service was conducted at the Frick home on Wednesday afternoon by the Rev. Dr. Leighton Parks, pastor of St. Bartholomew&apos;s Episcopal Church. This was attended by members and very intimate friends of the family, Trustees of the Metropolitan Museum of Art, Officers of the Links Club, and Directors of the United States Steel Corpn. Henry Clay Frick was born Dec. 19, 1849, in West Overland, Westmoreland Co., Pa. His father, John W. Frick, was a farmer of Swiss ancestG, and his mother, Elizabeth Overholt Frick, a member of an old Mennonite family. Until he was sixteen, he spent his time at school, on his father&apos;s farm, and in his grandfather&apos;s distillery, where he kept books. He attended Otterbein University, in Ohio, for a year. Frick, learning that coke was an essential of the already rapidly developing steel business, early invested every cent he could get in coking-coal lands. With the help of an associate of his grandfather, he formed the corporation of Frick & Co., coke dealers, and acquired fifty-one ovens in the Connellsville region and 300 acres of soft-coal lands. During the panic of &apos;73, with the help of Judge Thomas Mellon, a Pittsburgh &apos;banker, he bought out his partners and while coke was selling at 90 cents a ton enlarged his purchases of suitable lands. Later, the price of coke increased until it was selling at $5 a ton. Before he was 30 years old, Frick was rated a millionaire. Association with CaRnegie In 1878, he sold an interest in the business Do E. M. Ferguson of New York, and later a share to Mr. Ferguson&apos;s brother. Four years later the business was reorganized into the H. C. Frick Coke Co. with vast coal lands, great banks of ovens, and a capitalization of $2,000,000. Then began his association with Andrew Carnegie. He exchanged a part of his coke interest for shares in Carnegie Brothers of Pittsburgh,

Jan 1, 1920

By Mark Sheppard

DuRing the winter of 1937, the writer visited a West Virginia stone quarry at which the overburden is stripped hydraulically. The quarry is in a bed of limestone, about 200 ft. thick, which outcrops on a hillside above a small river; the quarry face is 175 ft. high. The top of the stone is cut in all directions by erosion channels, which are filled with a tough, red clay. Some of the larger channels are 30 ft. deep and 8 ft. wide. The thickness of the clay overburden ranges from a few inches to 10 ft., the average being estimated as less than 3 feet. The topography of the district is rugged, and the hillside above the quarry face is not suited to the use of the usual mechanical methods of moving dirt. Until hydraulicking was started 10 years ago, the overburden was dug by hand labor, dumped to the quarry floor and transported to the dump in quarry cars. Cleaning deep channels was a slow and expensive process. When hydraulicking was started, the top of the quarry face was over 200 ft. above the level of the river. The pipe line was carried in a semicircle around the top of the quarry about 200 ft. from the face and about 50 ft. above it. As there is no adequate supply of water above the quarry, the water must be pumped from the river. As quarrying progressed the pipe line was moved until the discharge points are now over 300 ft. above the river. Water is pumped from the river by a four-stage centrifugal pump having a 5-in. intake and a 4-in. discharge. It is direct-connected to a 200-hp., 2300-volt, 1760-r.p.m. induction motor. At 1760 r.p.m. the rated capacity of the pump is 750 gal. per minute under a head of 600 ft. The pump is installed in a house of frame construction on the river bank, about 10 ft. above normal water level, which also houses the pump for the mill-water supply. Above the pumps are hoisting bays into which the motors are raised whenever the river reaches flood stage. An 8-in. suction line, equipped with a strainer and a foot valve, takes the water from a concrete sump at the edge of the river. The pipe line from the pump consists of 1750 ft. of 8-in. spiral steel flanged pipe and

Jan 1, 1938

By D. Van Winkle, C. Zener, H. Nielsen

THe internal friction of metals has been studied frequently at elevated temperatures.1-4 In most cases it rises rapidly with increasing temperature. The notable exceptions are ferromagnetic materials, and lead.2 This paper describes an investigation of the general features of the high-temperature internal friction of 70-30 alpha brass. Experimental Method The internal friction of a metal is a measure of the rate at which it dissipates energy of vibration. The measure adopted here, I/Q, is (I/2p) times the specific damping capacity, a measure commonly used by engineers. In the measurements of this investigation, the stress level was kept so low that the observations were independent of the stress, The general method of making such measurements, and of observing temperature of a specimen during a measurement, has been described.5.6 The driver and detector coils were wound with wire insulated with glass thread, in order to withstand the high temperatures used. In previous work electrical eddy currents in the specimen served as the coupling between the mechanical vibration of the specimen and the electrical circuits of the driver and detector. The high values of the internal friction in the present investigation rendered this coupling insufficient. In order to increase this coupling, pole pieces cut from ordinary telephone diaphragms were attached to the specimen. A mixture of French chalk and water glass proved a satisfactory cement. All measurements were made at the fundamental frequency for transverse vibration, which lay between 600 and goo cycles per second. Specimens The measurements described herein were made upon a single cylindrical rod of brass, kindly furnished by Dr. Cyril Stanley Smith, of the American Brass Co. This rod was the specimen E of the set of alpha-brass rods described in an earlier paper.6 Successively larger grain sizes were obtained by annealing at .successively higher temperatures. A slice was cut off one end after each set of measurements. Grain counts were made on each slice by W. E. Lindlief, of the American Brass Co. Nine fields were viewed on each piece, located as shown in Fig. I. Results are given in Table I. The grain size is defined in the usual way; namely, Grain size = I/n1/2 where n is the mean number of grains per square millimeter. Experimental Results This paper is concerned exclusively with the part of the internal friction that be. comes dominant at high temperatures. It is thus desirable to separate this part of the internal friction from the part that is

Jan 1, 1942

By C. Zener, H. Nielsen, D. Van Winkle

THe internal friction of metals has been studied frequently at elevated temperatures.1-4 In most cases it rises rapidly with increasing temperature. The notable exceptions are ferromagnetic materials, and lead.2 This paper describes an investigation of the general features of the high-temperature internal friction of 70-30 alpha brass. Experimental Method The internal friction of a metal is a measure of the rate at which it dissipates energy of vibration. The measure adopted here, I/Q, is (I/2p) times the specific damping capacity, a measure commonly used by engineers. In the measurements of this investigation, the stress level was kept so low that the observations were independent of the stress, The general method of making such measurements, and of observing temperature of a specimen during a measurement, has been described.5.6 The driver and detector coils were wound with wire insulated with glass thread, in order to withstand the high temperatures used. In previous work electrical eddy currents in the specimen served as the coupling between the mechanical vibration of the specimen and the electrical circuits of the driver and detector. The high values of the internal friction in the present investigation rendered this coupling insufficient. In order to increase this coupling, pole pieces cut from ordinary telephone diaphragms were attached to the specimen. A mixture of French chalk and water glass proved a satisfactory cement. All measurements were made at the fundamental frequency for transverse vibration, which lay between 600 and goo cycles per second. Specimens The measurements described herein were made upon a single cylindrical rod of brass, kindly furnished by Dr. Cyril Stanley Smith, of the American Brass Co. This rod was the specimen E of the set of alpha-brass rods described in an earlier paper.6 Successively larger grain sizes were obtained by annealing at .successively higher temperatures. A slice was cut off one end after each set of measurements. Grain counts were made on each slice by W. E. Lindlief, of the American Brass Co. Nine fields were viewed on each piece, located as shown in Fig. I. Results are given in Table I. The grain size is defined in the usual way; namely, Grain size = I/n1/2 where n is the mean number of grains per square millimeter. Experimental Results This paper is concerned exclusively with the part of the internal friction that be. comes dominant at high temperatures. It is thus desirable to separate this part of the internal friction from the part that is

Jan 1, 1942

Book Review MAN-TO-MAN: THE STORY OF INDUSTRIAL DEMOCRACY. By John Leitch, Phila¬delphia, Pa. The B. C. Forbes Publishing Co., New York, 1919, 2.19 pp., 7 1/2 X 5 in. $2.00. "Man to Man" is a short, well-written, well-printed, easy to read and very interesting hook. It is an account of a method introduced into more than twenty industrial plants to give the workers a share in managing their own troubles. It is not a panacea for labor troubles and strikes, but neither have existed where the new method has been tried. The scheme is, in a word, to organize the working force like the government, having a cabinet composed of the executives, a senate composed of foremen, and a house composed of men elected by fellow workers from all departments. This governing machinery takes up all complaints of workers, investigates, reports, and settles. The increased profits due to economy and increased production from this cooperation are divided 50-50 between the company and the men. Experience has shown that, since inattention, tardiness, irregularity, and inefficiency tend to reduce their profits, all men very quickly, after once convinced of the sincerity of the management in their scheme of cooperation, eliminate them because it is for their personal profit. Astonishing results have been attained, including higher wages, greater output, lower unit costs, great reduction in labor turnover, elimination of waste, an increased loyalty and a waiting list of employees even in periods of labor shortage. Profit sharing as such and stock ownership as a benefit to industrial relations are discussed briefly and illuminatingly, although they are not believed by the author to he the best way to bring about the human relation between those who work,for and those who work with money. The author is not against unions but does not believe the union is the best medium for improving industrial relationship. The look is nowhere dogmatic but is always forceful and convincing and, being well written, is very entertaining. It is doubtful if "Industrial Democracy" is the right expression for the solution of the problem but certainly anything that will place on the shoulders of labor some of the responsibility of industry and will increase production is tine much-to-be-desired desideratum. It is a. contribution to the solution of our biggest problem and should be read by everyone who employs men and who has been worried by the labor turnover. P. E. B.

Jan 7, 1919

By Mark Sheppard

DURING the winter of 1937, the writer visited a West Virginia stone quarry at which the overburden is stripped hydraulically. The quarry is in a bed of limestone, about 200 ft. thick, which outcrops on a hillside above a small river; the quarry face is 175 ft. high. The top of the stone is cut in all directions by erosion channels, which are filled with a tough, red clay. Some of the larger channels are 30 ft. deep and 8 ft. wide. The thickness of the clay overburden ranges from a few inches to 10 ft., the average being estimated as less than 3 feet. The topography of the district is rugged, and the hillside above the quarry face is not suited to the use of the usual mechanical methods of moving dirt. Until hydraulicking was started 10 years ago, the over- burden was dug by hand labor, dumped to the quarry floor and transported to the dump in quarry cars. Cleaning deep channels was a slow and expensive process. When hydraulicking was started, the top of the quarry face was over 200 ft. above the level of the river. The pipe line was carried in a semi- circle around the top of the quarry about 200 ft. from the face and about 50 ft. above it. As there is no adequate supply of water above the quarry, the water must be pumped from the river. As quarrying progressed the pipe line was moved until the discharge points are now over 300 ft. above the river. Water is pumped from the river by a four-stage centrifugal pump having a 5-in. intake and a 4-in. discharge. It is direct-connected to a 200-hp., 2300-volt, 1760-r.p.m. induction motor. At 1760 r.p.m. the rated capacity of the pump is 750 gal. per minute under a head of 600 ft. The pump is installed in a house of frame construction on the river bank, about 10 ft. above normal water level, which also houses the pump for the mill-water supply. Above the pumps are hoisting bays into which the motors are raised whenever the river reaches flood stage. An 8-in. suction line, equipped with a strainer and a foot valve, takes the water from a concrete sump at the edge of the river. The pipe line from the pump consists of 1750 ft. of 8-in. spiral steel flanged pipe and 800 ft. of 4-in. spiral steel flanged pipe. The connection from the pump

Jan 1, 1938

As described in the section on the Palabora twin crushers, the Palabora ore consists of two types: a carbonatite containing a low titanium magnetite, and a foskorite containing high titanium magnetite. As the Palabora pit was widened and deepened, more and more of the foskorite had to be mined. The 25,000 mt expansion of the Palabora plant which went into operation in early 1977 therefore takes its feed from the foskorite section of the orebody. For the expansion, a third 54 in. by 74 in. gyratory crusher was installed to crush feed for two 32 ft by 15 ft (9.75 by 4.6 m), 9000 hp (6710 kw) autogenous single -stage grinding mills. These units are located near the two existing primary crushers, and the ground ore is pumped 5277 ft (1640 m) to the expanded flotation plant by five stages of centrifugal pumps. The new gyratory is installed in a unique Figure-8 shaped enclosure with the crusher in the smaller 27 ft 11 in. (8. 5 m) diameter cylinder and the maintenance area in the 36 ft 1 in. (11 m) diameter cylinder. Cylinder walls are only 23.6 in. (600 mm) thick because their circular design permits all the concrete to be in compression. A rectangular dump pocket which sits on the smaller cylinder contains two manganese steel faced splitters to protect the crusher spider and countersunk water spray headers under the dumping positions for dust suppression. The dump pocket holds 330 st or 300 mt and is also lined with manganese steel. The crusher is mounted on a reinforced concrete diaphragm over the 363 st (400 mt) crushed ore pocket. In the back of the pocket is plastic pipe. Radioactive level control sources are lowered into this pipe from the crusher support floor. The pipe is protected by concrete covered with steel castings. Level control detectors are mounted on the front wall of the pocket. Liner plates on the crushed ore pocket walls are removed and in- stalled by the use of a circular monorail and trolley mounted on the pocket ceiling. The door in the front of the crushed ore pocket is hinged at the top rather than at the sides and is raised by an electric winch. For removal of the eccentric, rails are installed in the pocket and a unique hydraulically operated cart is moved under the eccentric. A platform is raised to receive the eccentric and lowered so that it may be removed. Crushed ore is removed from the pocket by a hydraulically powered, 8 ft

Jan 1, 1978

By Mark Sheppard

DuRing the winter of 1937, the writer visited a West Virginia stone quarry at which the overburden is stripped hydraulically. The quarry is in a bed of limestone, about 200 ft. thick, which outcrops on a hillside above a small river; the quarry face is 175 ft. high. The top of the stone is cut in all directions by erosion channels, which are filled with a tough, red clay. Some of the larger channels are 30 ft. deep and 8 ft. wide. The thickness of the clay overburden ranges from a few inches to 10 ft., the average being estimated as less than 3 feet. The topography of the district is rugged, and the hillside above the quarry face is not suited to the use of the usual mechanical methods of moving dirt. Until hydraulicking was started 10 years ago, the overburden was dug by hand labor, dumped to the quarry floor and transported to the dump in quarry cars. Cleaning deep channels was a slow and expensive process. When hydraulicking was started, the top of the quarry face was over 200 ft. above the level of the river. The pipe line was carried in a semicircle around the top of the quarry about 200 ft. from the face and about 50 ft. above it. As there is no adequate supply of water above the quarry, the water must be pumped from the river. As quarrying progressed the pipe line was moved until the discharge points are now over 300 ft. above the river. Water is pumped from the river by a four-stage centrifugal pump having a 5-in. intake and a 4-in. discharge. It is direct-connected to a 200-hp., 2300-volt, 1760-r.p.m. induction motor. At 1760 r.p.m. the rated capacity of the pump is 750 gal. per minute under a head of 600 ft. The pump is installed in a house of frame construction on the river bank, about 10 ft. above normal water level, which also houses the pump for the mill-water supply. Above the pumps are hoisting bays into which the motors are raised whenever the river reaches flood stage. An 8-in. suction line, equipped with a strainer and a foot valve, takes the water from a concrete sump at the edge of the river. The pipe line from the pump consists of 1750 ft. of 8-in. spiral steel flanged pipe and

Jan 1, 1938

By Frederick Laist

0. C. RALSTON, Salt Lake City, Utah.-I have merely glanced over this paper, consequently, I am hardly in a position to discuss it intelligently. There is one thing, however, that is of interest, that is, the claim that the oil mixture which they have chosen is the best adapted to the work at hand. I would like to ask Mr. Mathewson if they still feel that that is the case-if that really does give the best grade of concentration and the best extraction for the same money, compared to any particular oil mixture which they could get. E. P. MATHEWSON, Anaconda, Mont.-We are still using that mixture, and we consider it the most economical mixture used. DAVID COLE, El Paso, Texas.-I would like to ask Mr. Ralston if there are some other mixtures that would be better? E. P. MATHEWSON.-We are open to suggestions. 0. C. RALSTON.-My own paper on oils* calls attention to the fact that certain hardwood oils, especially the tars, are now being burned or wasted. A great deal of hardwood tar is available as low as 4 or 5 c. per gallon, that being its value as fuel under the boilers. As a matter of fact, a great deal of testing has been done with only the commercial products that are as a usual ride sold on the market. Very little hardwood tar is sold on the market. In asking a great many people who have tested flotation oils, I have not heard hardwood tar mentioned very often. I think I would add to that that the hardwood tars can probably be bought in quantity comparable with the sludge acid at Anaconda, and. should contain a greater proportion of the frothing constituent, and at a price fairly commensurate with what they pay for the sludge acid. E. P. MATHEWSON.-I would like to make a correction in one statement I made that there has been no change made in the mixture. This change has been made: We found that the amount of wood creosote in treating the sand from tables was extremely small, and we tried some experiments on a large scale, dropping it out and using simply the sludge acid and sulphuric acid. We found that this gave practically as good results as wood creosote. We use wood creosote in treating the slimes. We find it necessary in that operation. DAVID COLE.-I would like to ask, what is sludge acid?

Jan 10, 1916

By Russell G. Wayland

This paper gives the author&apos;s personal idea of the general viewpoint of the world&apos;s largest mica consumer, the U. S. Army, toward the supply, uses, and conservation of mica. However, to cover so broad a subject in a brief paper will require the dismissal of many phases with little or no mention. For example, it will be necessary to omit further reference to phlogopite or amber mica, even though amber block and splittings for certain spark plugs and commutator segments present some supply problems. This paper will deal entirely with muscovite, or white mica. Muscovite Mica Muscovite mica is available commercially in four general forms; namely, as block mica, as splittings, as washer punch, and as scrap mica.1 No strategic importance is attached to washer punch and scrap mica, even though scrap has found some use in military construction and in electrical ceramics. The use of washer punch as such has fallen off with the non-manufacture of household electrical appliances. Some qualities of block mica are also of little or no interest, but other qualities of block mica and all splittings are considered of vital importance. Army equipment requires large amounts of muscovite mica splittings in the form of built-up mica commutator segments and coil insulation in motors and generators. Other military items using significant amounts of muscovite splittings are transformers, switchboards, and blasting apparatus. Flexible mica tape, made from bookform or loose-dusted splittings cemented to paper, linen, glass cloth, and other backing, is widely used in coil insulation in heavy electrical equipment and in aircraft generators. All muscovite mica splittings come from India, principally because of the enormous amount of hand labor required in their preparation. In this emergency, the need for them was anticipated and large industry and government stocks were on hand, while shipments have continued to come by sea in spite of wartime hazards. With the possible exception of certain bookform splittings, no trouble is anticipated in supply. Accordingly, the remainder of this paper is devoted to block (or sheet) muscovite mica, including condenser film that is split from block. The Mica Problem Block muscovite mica is commercially classified into the following general qualitie3, beginning with the best quality: 1. Clear and Slightly Stained (C & SS). 2. Fair stained (FS). 3. Good stained (GS). 4. stained (s). 5. Heavy Stained (HS). 6. Black spotted. The ratio of relative commercial abundance in the present new supply of these micas is approximately 1 C & SS to 4 FS to ro GS to 14 S to whatever the

Jan 1, 1948

By C. E. Berry

Natural stone or manufactured porcelain pebbles are used as the grinding elements in pebble mills and the mills are lined with stone or porcelain blocks. Steel balls usually form the grinding medium in ball mills, and the mills may be lined with steel. Pebble mills are used to avoid contamination by metal of the material being ground, to avoid rapid wear due to corrosion, and for other specialized reasons. Belgian silex (silica) blocks formerly were used widely for lining pebble mills, because of their good resistance to wear, light color, and low cost, but the importation of these blocks was suspended early in the war. The stocks of Belgian silex diminished so rapidly that it was found desirable to compare the properties of a number of domestic substitutes for use in critical operations. Accordingly, a study was made to determine the best substitutes for fine grinding of white pigment and for certain heavy-chemical process work such as the disintegration of phosphate rock in weak phosphoric acid solution. A comprehensive survey of substitute lining materials was not contemplated. It was stipulated at the beginning of the investigation that only materials on the market, available in large quantities, would be tested and that these should be reasonable substitutes from a a ance viewpoint as determined from known physical characteristics. Marble and limestone, for example, could be eliminated immediately. Quartzite, granite and porcelain were selected as likely substitutes for Belgian silex and were subjected to quality tests. Materials Tested 1. Belgian Si1ex.—Sample blocks of a standard grade were taken from crates in which they had been imported. The stone was light gray in color and contained inclusions of small clusters of quartz crystals as well as light colored portions that might be calcite. This was a siliceous rock which appeared to be of igneous origin. 2. Quartzite.—Samples of quartzite were obtained from a quarry in Minnesota. The blocks exhibited a crystalline fracture. The stone was pink in color and composed of fine quartz crystals bound together with a siliceous cement. 3. Granite A was a fine-grained granite quarried in South Carolina. 4. Granite B was coarse-grained granite quarried in South Carolina. 5. Granite C was a coarse-grained granite quarried in North Carolina. 6. Porcelain A.—Sample blocks of the pebble-mill lining material were obtained direct from the manufacturer. It was white in color and of lower specific gravity than the natural materials. It did not have a crystalline structure. 7. Porcelain B.—Sample pebble-mill lining blocks of the porcelain were received direct from the manufacturer. It was white

Jan 1, 1948

By Russell G. Wayland

This paper gives the author&apos;s personal idea of the general viewpoint of the world&apos;s largest mica consumer, the U. S. Army, toward the supply, uses, and conservation of mica. However, to cover so broad a subject in a brief paper will require the dismissal of many phases with little or no mention. For example, it will be necessary to omit further reference to phlogopite or amber mica, even though amber block and splittings for certain spark plugs and commutator segments present some supply problems. This paper will deal entirely with muscovite, or white mica. Muscovite Mica Muscovite mica is available commercially in four general forms; namely, as block mica, as splittings, as washer punch, and as scrap mica.1 No strategic importance is attached to washer punch and scrap mica, even though scrap has found some use in military construction and in electrical ceramics. The use of washer punch as such has fallen off with the non-manufacture of household electrical appliances. Some qualities of block mica are also of little or no interest, but other qualities of block mica and all splittings are considered of vital importance. Army equipment requires large amounts of muscovite mica splittings in the form of built-up mica commutator segments and coil insulation in motors and generators. Other military items using significant amounts of muscovite splittings are transformers, switchboards, and blasting apparatus. Flexible mica tape, made from bookform or loose-dusted splittings cemented to paper, linen, glass cloth, and other backing, is widely used in coil insulation in heavy electrical equipment and in aircraft generators. All muscovite mica splittings come from India, principally because of the enormous amount of hand labor required in their preparation. In this emergency, the need for them was anticipated and large industry and government stocks were on hand, while shipments have continued to come by sea in spite of wartime hazards. With the possible exception of certain bookform splittings, no trouble is anticipated in supply. Accordingly, the remainder of this paper is devoted to block (or sheet) muscovite mica, including condenser film that is split from block. The Mica Problem Block muscovite mica is commercially classified into the following general qualitie3, beginning with the best quality: 1. Clear and Slightly Stained (C & SS). 2. Fair stained (FS). 3. Good stained (GS). 4. stained (s). 5. Heavy Stained (HS). 6. Black spotted. The ratio of relative commercial abundance in the present new supply of these micas is approximately 1 C & SS to 4 FS to ro GS to 14 S to whatever the

Jan 1, 1948