Search Documents

THE increased demand for titanium alloys with improved high-temperature creep strengths has stimulated interest in silicon as an alloying addition to titanium. Silicon is a potent solid-solution strength-ener and, if added in sufficient concentration and properly heat-treated, can also dispersion-strengthen titanium by eutectoid decomposition.' However, better understanding of the nature and distribution of the resulting silicide dispersion in more highly alloyed titanium matrices is necessary for the development of useful titanium alloys which utilize the latter strengthening mechanism. This note describes the chemical and crystallographic characteristics of the silicide phase as it occurs in a typical high-temperature near-a titanium alloy matrix. Several Ti-6A1-3Sn-3Zr a11oys containing various amounts of silicon ranging from 0.1 to 1.0 pct were melted as 10- to 20-lb ingots and processed into 1/2-in.-diam bar stock. The microstructures of specimens annealed at various temperatures were conveniently summarized by the (Ti-6Al-3Sn-3Zr)-Si pseudobinary phase diagram illustrated in Fig. 1. Comparison with the Ti-Si equilibrium diagram indicates the substitutional solutes (Al-Sn-Zr) increase the eutectoid temperature and decrease the a terminal solubility. Annealing at temperatures sufficiently high to dissolve the silicon in a ß solid solution and cooling rapidly enough to preclude coarsening generally produced a uniform dispersion of fine silicide particles, whereas annealing at temperatures near but below the ß transus produced relatively coarse silicide particles. Annealing in the limited a, plus 3 region produced a duplex coarse and fine silicide array. Several a-annealed specimens were examined by X-ray diffraction to determine the crystallographic identity of the precipitate phase. Copper Ka X-ray diffraction patterns of bulk specimens which contained 0.5 and 0.8 pct Si were virtually identical to that of the silicon-free Ti-6Al-3Sn-3Zr base alloy except for a slight shift in some of the high-angle diffraction lines. Apparently the silicide volume fraction was too low to be detected in bulk specimens. X-

Jan 1, 1969

By John T. Galey

Oil and gas development in southern Pennsylvania during 1937 was marked by considerably increased activity in deep-sand drilling. Nine tests were completed to the Oriskany sand: one in Independence and three in South Beaver townships, Beaver County; one in Franklin township, Butler County, two in Slippery Rock township, Lawrence County; one in Mt. Pleasant township, Washington County, which is drilling below the Oriskany, and one in Fairfield township, Westmoreland County. Two of these wells, both of which were in the Blackhawk pool, South Beaver township, Beaver County, obtained wet gas with open-flow volumes of 1.5 million cu. ft. and 3.1 million cu. ft. and closed-in pressures of 1900 Ib. The remaining seven were unproductive in the Oriskany. Two wells, one in Hampton township, Allegheny County, which is shut down temporarily as a result of a gas pocket, and one in South Beaver township, Beaver County, are drilling to the Oriskany. One deep test on the Chestnut Ridge anticline, South Union township, Fayette County, was completed after considerable difficulty as a dry gas well in the Onondaga limestone. At this locality the cherty limestone is porous as a result of fracturing. Three additional tests are under way in the area, one in South Union township, a second in North Union township, and a third in Wharton township. Completions Oil.—Despite price cuts and production curtailment of Pennsylvania Grade crude, caused largely by a decreasing demand from export markets, operation in the shallow oil areas continued at a fairly high rate and a number of good wells were completed. Some of these were new wells in close proximity to old production and others were old wells drilled into deeper pays. One new well of a number of producers drilled to the Nineveh Thirty-foot sand in the Harvey pool, Center township, Green County, made 400 bbl. of oil and 500 million cu ft. of gas the first 24 hr. The Chambers dam pool of Amwell and South Franklin townships, Washington County, yielded a number of Fifth Sand producers with initials as high as 200 bbl. Several wells in the old Mars-Butler field

Jan 1, 1938

By R. E. Collins, Paul B. Crawford

Mathematical equations have been derived to show the effect of the slippage phenomomenon (Klinkenberg effect) on unsteady-state gas flow through porous media. The assumption is made that the slippage may be represented by an equation of the type It is pointed out that most of the existing data on unsteady gas flow may be corrected for slippage by a simple change in definition of the dimen-sionless groups. INTRODUCTION Several solutions to the various problems associated with the unsteady-state flow of gas through porous media have been recently presented in the literature.','" The cited publications have resented solutions for flow under ideal conditjons. The principal assumptions involved include: (a) the density of the gas obeys the perfect gas law; (b) the viscosity of the gas is constant; and (c) the gas permeability is constant. Few, if any, actual gases under reservoir conditions are believed to conform with the above, but the ideal solutions do provide the basis for making improved estimates on the performance of gas reservoirs. The purpose of this paper is to show the performance characteristics when assumption (c) is corrected for the slippage phenomenon or the Klinkenberg effect. This is believed to be a step nearer to reality. MATHEMATICAL DEVELOPMENT Case 1. Gas Flow — Ideal Conditions The equations describing the flow of gas under ideal conditions have been clearly presented in the cited literature; however, for completeness of this work they are repeated here. The basic differential equation describing the flow of gas is Equation (6). It may be derived as follows: The continuity equation, the perfect gas law and Darcy's law are combined to give: Manuscript received in the Petroleum Branch office Aug. 3, 1963 or If — is constant, Equation (5) is rewritten to form the basic Equation (6). or for the linear case A dimensionless equation is obtained by dividing through by (pl)z and making the substitutions shown below: The resulting equation is A similar procedure for the radial case leads to the following equations: where and Equations (11), (12), and (13) are those used by Bruce, et al., and Jenkins and Aronofsky for their computational work.

Jan 1, 1953

PAUL. D. MERICA, Bayonne, N. J. (written discussion*)..-The mode of intercrystalline oxidation which the authors" have so well observed and described is characteristic of nickel that has been exposed' to: the action of an oxidizing atmosphere at higher temperatures, such as, those at which; it is annealed or heated for rolling or forging. Oxidation under such conditions proceeds inward from the surface along the, crystal boundaries' producing a net-work, probably of oxide; which causes a very brittle condition of this surface material. This, in turn, generally results in surface cracking and checking during further, rolling and a defective sheet or other product is produced. An example of this is shown in Fig. 2, which shows the surface, of a badly surface-cracked sheet of nickel produced by incorrect heating con-ditions. A cross-section of this sheet etched with nitric acid is shown in Fig. 1, which reveals the intercrystalline oxidation network adjacent to both surfaces.These layers are so brittle that it is not possible to deform them by rolling without severe cracking along these lines or, planes of weakness. The best, and possibly only, remedy for this condition lies in its prevention by the maintenance of a neutral soft flame for heating and annealing nickel during the entire course of its manufacture. I should like to suggest that, those making microscopic investigations of nickel and nickel-rich alloys try the use of acetic-acid .solutions of nitric acid for etching these metals rather than aqueous solutions, of nitric acid. I have found that a solution containing 50 per cent. nitric acid, from 25-45 -per. cent. acetic acid, and from 25-5 per cent. water gives excellent results with. Wrought and cast nickel and Morsel metal and superior results to those obtained with nitric acid, alone. The acetic. acid seems to inhibit the passivity that nickel often assumes toward nitric acid and much more uniform etching may, be obtained. The proportions of nitric and acetic, acid may be varied somewhat from those given without mate-rially altering the quality of the etching, although without any distinct improvement in it.

Jan 12, 1919

By Samuel L. Hoyt

This paper gives a brief description of an investigation made several years ago on the diffusion of zinc into copper. The material for that study was furnished in the form of thin copper strips coated with zinc. The result was required rather quickly and at not too great an expense, and especially information was desired as to the rate at which zinc would diffuse from the zinc coating into the copper and the temperature at which the operation should be carried out. A study of the requirements of this problem indicated that the solution might be secured by means of six determinations. This is the smallest number that will give the information desired and, at the same time, furnish checks on the accuracy of the determinations which justify an abbreviated experimental program. This does not count a preliminary test which was designed to give some idea of the correct temperature to use. The minimum number of temperatures that can be used is two. Knowing the rates of diffusion of zinc into copper at two properly chosen temperatures, it is possible to calculate the rate for any other temperature, and also to check the accuracy of the determination by means of the heat of diffusion, which is calculated from the effect of temperature on the rate of diffusion. The minimum number of determinations at any one temperature is three. The amount of diffusion which occurs at a fixed temperature is definitely related to the time of diffusion, so that by determining the amount of diffusion for three different time intervals, this relationship may be established and possibly a check on the accuracy may be secured. This accounts for the six determinations or experiments, and suggests the logical plan of the work. The check used here is not generally applicable to diffusion phenomena, but it seems to hold closely enough for the limited amount of diffusion in this investigation to justify its use. The samples used were 5 to 6 mils thick and about 1 in. square. They were placed between iron blocks and set in the hot zone of a nichrome furnace which had been brought to the desired temperature Time was taken from the moment the samples reached the furnace

Jan 1, 1929

By Edward Pesout

THE McGill smelter started operations in the year 1907. The smelter furnaces were fired with run-of-mine coal on grates until April 1911, when oil firing was introduced. Oil firing continued until April 1918, when the initial coal-pulverizing plant was started.1 EARLY PULVERIZING PLANT Various alterations were made to that plant during its operation, one of the more important being in connection with the system for delivering pulverized coal. In order to minimize coal-dust explosions and fires, the return portion of the main delivery line was eliminated in the year 1928. Thereafter coal-dust explosions and fires were greatly reduced. Pulverized coal was prepared at this plant primarily for the reverberatory furnaces, but for several years it was also delivered to the converting plant, roasters and power-plant boilers by a system of auxiliary fans and delivery lines. During the period March 29 to April 8, 1929, one reverberatory furnace was fired with pulverized coal produced by an Aero, type J, unit coal pulverizer with a rated capacity of 5 tons per hour. This machine actually pulverized its rated capacity but the product was too coarse. After certain regulations, a finer product was obtained but the pulverizer capacity decreased and this resulted in insufficient coal for efficient furnace operation. Table I gives a comparison of the average screen analyses of the pulverized-coal products from the impact-type unit pulverizer and the regular coal-plant installation. [ ] It was definitely proved that this size and type of unit pulverizer could not furnish sufficient coal of proper fineness to give smelting results comparable to that obtained with the regular coal-pulverizing plant. The coal from this unit pulverizer was so coarse that it did not ignite or burn properly and thus did not produce the proper heat for efficient smelting. During the latter part of 1929 and the early part of 1930, experimental work was conducted with a 7-ft. 0-in. by 48-in. Hardinge conical ball-mill coal-grinding unit, which was installed alongside a furnace in the reverberatory building. Results obtained from the test run indicated that this unit would furnish sufficient coal of proper fineness for good smelting.

Jan 1, 1945

CONTENTS DAVIS, CARL R., WILLEY, J. L., and EWING, S. E. T.-Recent Developments in the Fine Grinding and Treatment of Witwatersrand Ores. Discussed by Charles E. Locke, H. W. Hardinge, H. N. Spicer, G. M. Brown, Justice F. Grugan, R. C. Canby 1 WEINIG, A. J., and BOWEN, MAX W.-Determination of Dissolved Oxygen in Cyanide Solutions. Discussed by A. L. Blomfield, M. F. Dycus, A. W. Bull.... 4 LEPSOE, ROBERT.-Precipitation Efficiency of Zinc Dust in Cyanide Process. Discussed by G. M. Brown, Charles E. Locke 5 Recent Developments in the Fine Grinding and Treatment of Witwatersrand Ores Discussion of the paper of CARL R. DAVIS, J. L. WILLEY, S. E. T. EWING, presented at the New York Meeting, February, 1925, and issued as Paper No. 1386-B, with MINING AND METALLURGY, December, 1924. CHARLES E. LOCKE, Cambridge, Mass.-In this country, we have come to think that we should use smaller size of feed in our ball-mills. I will admit that a ball-mill is not comparable to a tube-mill, as conditions may not be the same, but there we have an unusual demonstration of the advantage of a coarser feed. Further investigation along this line is going to lead to some valuable results. The authors have overcome the difficulty of this coarse feed by taking out what I would call the difficult lumps, It is not clear from the paper whether many of these difficult lumps' may not be 'reduced portions of their grinding media. H. W. HARDINGE, New York, N. Y.-The idea is not exactly new because in 1911 they used the miner to reduce the finer material. We proceeded three or four years using many tons, about 15 tons. or nearly the same proportion of ore to grinding medium. Another thing to be taken into account is the hardness of the ore being ground. In South Africa, the transportation costs must be, taken into account. They are also making progress in the method of using tube-mills and ball-mills instead of stamps. Experiments are to be conducted with 10-ft. diameter mills there, with the object of increasing the mass action and agitation which, as has been demonstrated under different circumstances, increases the overall efficiency.

Jan 6, 1925

By Ben-Zion Weiss, Melvin R. Meyerson

FATIGUE crack propagation in some aspects can be viewed as being a result of localized plastic deformation concentrated near the tip of the crack.' Deformation is influenced by microstructure which in turn can affect the fatigue crack growth significantly. To study the effect of localized microstructural changes on fatigue crack propagation, cantilever-type notched specimens were subjected to cyclic bending at constant load amplitude. The extent of fatigue crack propagation was obtained by measuring the length of the crack by periodic observation with a microscope on the polished side of the sample,2"4 and these data were used in preparing the curves in the figures which follow. Figs. 1 (solid lines) and 2 show experimental results obtained in austenitic type 302 stainless steel containing higher than standard carbon (0.24 pct C) and 310 stainless steel. Both steels were homogenized for 8 hr at 1120°C and then water-quenched in order to prevent the precipitation of carbides. Fig. 3 shows experimental results obtained on 9440 low alloy steel in the normalized condition and in the quenched and tempered (580°C) condition. Indications of microstructural influence can be seen in scattering of the experimental data. The degree of scattering depends on both the microstructure and the amount of cyclic stress applied to the sample. For microstructures which are more easily deformed plastically, e.g., normalized or annealed as compared with hardened and tempered structures, the scattering is greater. Similarly, higher stresses produce greater scattering in the results, regardless of whether the cause of the stress increase is due to initial loading conditions or the growth in crack length. Scattering is believed to be a result of partial redistribution in the stress field around the tip caused by plastic deformation. This opinion is borne out by much smaller scattering of experimental results in the austenitic 302 high-carbon (0.24 pct C) steel. In this steel, plastic deformation in the neighborhood of the crack causes partial mar-tensitic transformation of metastable austenite,5 which in turn restrains further plastic deformation. As a result, the stress redistribution around The tip is reduced. Partial martensitic transformation was confirmed

Jan 1, 1969

By W. Rostoker

IN the course of the development of the phase equilibrium diagram for the system Zr-Cr,' the structure of an as-cast allov having the composition ZrCr2 was analyzed and established to be isomorphous with MgZn2 (C14, hexagonal lattice, 12 atoms per unit cell). In a recent paper on the same system, Hayes, Roberson, and Davies' report for the ZrCr2 phase an isomorphy with MgCu2 (C15, cubic lattice, 24 atoms per unit cell). It appeared that this conflict might be resolved by assuming a high and low temperature modification for ZrCr2. That this was the case with the phase TiCr2 has recently been demonstrated by Levinger." Specimens of ZrCr2 annealed at 1200°, 1100°, 994", 900°, 834", 800°, and 700°C, respectively, and subsequently quenched were examined by X-ray diffraction analysis. It was successfully demonstrated that a transition from the MgZn, structure at lower temperatures to the MgCu, structure did occur at some temperature between 900" and 994°C. Table I lists the observed structures at the various annealing temperatures. In Table II, a summary of line spacings and intensities is given for each of the allotropic modifications. The first six lines of the MgCu2 structures have been located in the table to illustrate the close similarity between the patterns. Lattice parameters of the two modifications were calculated by a least squares solution of equations for interplanar spacings for a series of high angle lines. The results are as follows: MgZn2 type - c = 8.262 kX, A = 5.079 kX. MgCu2 type — a = 7.195 kX. It is interesting to note that TiCr2 behaves in reverse fashion yn that the MgCu, structure is the low temperature modification and the MgZn2 structure is the high temperature modification. References lR. F. Domagala, D. J. McPherson, and M. Hansen: This issue p. 279. 'E. T. Hayes, A. H. Roberson, M. H. Davies: Trans. AIME (1952) 194, p. 304; Journal of Metals (March 1952). 3B. W. Levinger: Trans. AIME (1953) 197, pp. 195-196; Journal of Metals (February 1953).

Jan 1, 1954

By Henry B. Smith, S. Paul Lindau

ThREe years ago it was decided by the management to granulate the matte that is produced in the smelter of the St. Joseph Lead Co. at Hereulaneum, Mo., thereby doing away with a large amount of labor in handling the matte and in subsequent crushing. On Mar. 1, 1915, the granulator was put in operation and up to Jan. 1, 1916, 18,735 tons had been granulated. The four blast furnaces have a daily output of about 280 tons of pig lead and 100 tons of matte assaying about 11.0 per cent. Pb. It is expected that projected improvements in roasting methods will eliminate more sulphur from the charge, and cut down the matte-fall to about one-half of the present figure. The blast furnaces are tapped into movable forehearths or settlers, 6 ft. by 4 ft. by 22 in., the slag overflowing into 27-cu. ft. slag cars which are hauled to the dump by electric locomotives. Previous to the adoption of granulation, the matte was tapped from the forehearths into small slag pots which were dumped after cooling. The matte cakes were broken with sledges, and transported to the crushing plant for fine crushing and screening. Here the matte was reduced to 1/4-in. size before being fed to the roaster bins. A Wedge and a Holthoff mechanical furnace are used for preroasting before sintering on the Dwight and Lloyd machines. The matte is returned to the furnaces as an iron flux until the gradually accumulating copper content reaches about 7 per cent., after which it is put aside to be concentrated in a small copper blast furnace, the resultant high-grade matte being sold. When the matte does not settle readily from the slag, two settling devices are often used, the second one being a large catch-pot, which gathers any matte that may overflow from the forehearth, the slag then overflowing from the catch-pot into the slag cars. When full of matte, the catch-pot is removed, allowed to cool, and the contents broken and crushed. a With the present plan of granulating, the matte is tapped into 6-cu. ft. iron ladles. These are transported to the granulating plant by a 5-ton

Jan 1, 1917

By Fred Wise

THE Getchell mine, a comparatively recent gold discovery, is in the old Potosi mining district, Humboldt County, Nevada. All ore is mined from open pits using Diesel shovels and gasoline trucks. Two types of ore are mined, oxide and sulphide. Oxide ores are siliceous or shaly; sulphide ores either gougy, siliceous or shaly. In mining, the sulphide ore is segregated into hard and gougy ore, because the gouge must be dried before it can be crushed, The oxide ore is not segregated. GENERAL METALLURGY The oxide ore is the leached outcrop that overlies the sulphide ore body. All of the iron and arsenic sulphides found in the sulphide ores have been thoroughly oxi-dized, The sulphur and arsenic have been leached out while the iron is present as hematite and limonite. The oxide ore is amenable to direct cyanidation, and although no visible free gold is present it is released at a comparatively coarse grind. The sulphide ore is more refractory, since the gold is all of micron size and some of it is locked in fine sulphides. It has been established microscopically that the free gold is coated with an impervious shell, which is probably some form of iron compound. The sulphide ores contain from 1.5 to 2 per cent of arsenic, which is present as orpiment and realgar with minor amounts of arsenopyrite. The orpiment and realgar are of a later mineralization than the gold and are barren. Roasting and washing of the sulphide ore prior to cyanidation is necessary to eliminate the arsenic, to alter the gold coating from an insoluble form to a soluble form, and to release the gold associated with the fine sulphides. Washing the ground calcine in weak sulphuric acid, trona, or hot water are beneficial in the order named, but to date the water is the best from an economic standpoint. Metallurgical tests as well as plant practice indicate that a certain amount of gold cannot be recovered even by going beyond economic practices, On this basis metallurgical results are viewed in the light of an optimum tailing rather than a per-centage of extraction.

Jan 1, 1940

By Samuel L. Hoyt

This paper gives a brief description of an investigation made several years ago on the diffusion of zinc into copper. The material for that study was furnished in the form of thin copper strips coated with zinc. The result was required rather quickly and at not too great an expense, and especially information was desired as to the rate at which zinc would diffuse from the zinc coating into the copper and the temperature at which the operation should be carried out. A study of the requirements of this problem indicated that the solution might be secured by means of six determinations. This is the smallest number that will give the information desired and, at the same time, furnish checks on the accuracy of the determinations which justify an abbreviated experimental program. This does not count a preliminary test which was designed to give some idea of the correct temperature to use. The minimum number of temperatures that can be used is two. Knowing the rates of diffusion of zinc into copper at two properly chosen temperatures, it is possible to calculate the rate for any other temperature, and also to check the accuracy of the determination by means of the heat of diffusion, which is calculated from the effect of temperature on the rate of diffusion. The minimum number of determinations at any one temperature is three. The amount of diffusion which occurs at a fixed temperature is definitely related to the time of diffusion, so that by determining the amount of diffusion for three different time intervals, this relationship may be established and possibly a check on the accuracy may be secured. This accounts for the six determinations or experiments, and suggests the logical plan of the work. The check used here is not generally applicable to diffusion phenomena, but it seems to hold closely enough for the limited amount of diffusion in this investigation to justify its use. The samples used were 5 to 6 mils thick and about 1 in. square. They were placed between iron blocks and set in the hot zone of a nichrome furnace which had been brought to the desired temperature Time was taken from the moment the samples reached the furnace

Jan 1, 1929

By H. C. Hardison

The Yates pool, Pccos County, Texas, has greater potential capacities than any other field in the United States. This field is notable for the large return it yields on capital invested, for low production costs and for the orderly and conservative manner in which it was developed and continues to be operated. The proven area is 20,000 acres and there are 392 producing wells, or approximately 1 well to 50 acres. The theoretical daily potential is 5,250,000 bbl. as determined by l-hr. open-flow gages. Individual well gages vary from a few barrels to 8500 bbl. per hour, and well depths range from 1000 to 1800 ft. The greater part of the production is from a very porous limestone, and by agreement no productive well has penetrated the lime more than 225 ft. The forces driving the oil from the formation to the surface are hydrostatic head, expanding gas or a combination of the two. The degree of effectiveness of either depends upon the structural position of, and porosity encountered in, the individual wells. Approximately 95 per cent. of the wells in the field flow naturally. The pipe line outlet of the field at the present time is 100,000 bbl. per day, which is less than 2 per cent. of the daily potential. Difficulties and Principles of Probation It became evident during the first year of the development of this field that operators would have to devise a scheme to allocate pipe line runs equitably among their different properties. When the idea of proration was first inaugerated, the matter of spacing wells was given consideration. This was given up through fear of legal difficulties. Storage was also a question that was given considerable thought, and a plan was finally developed which went into effect Oct. 1, 1927. It was decided that the oil runs should be prorated according to the total potential capacity of all the wells which the several operators had in the field. The potential capacity of the wells was measured by a l-hr. open-flow gage. All runs to storage by an operator were deducted from his daily allowance.

Jan 1, 1931

By R. G. Davies

Isothermal annealing of quenched Fe3Al reveals that the superlattice forms by the nucleation and growth of ordered domains. The activation energy for isothermal ordering and initial domain growth is -29 keal per mole, which is thought to he the activation energy for vacancy migration. Domain growth, in the absence of excess vacancies, has an activation energy of -100 keal per mole. A maximum in the hardness is observed when the structure consists Of ordered domains, -35-4 in size, growing into a short-range ordered matrix and, also as a function of degree of order, S, with an infinite domain size at S = 0.4 to 0.5. It is proposed that both maxima are due to a transition from deformation by unit dislocations to deformation by superdislocntions. FE-AL alloys containing more than -23 at. pet Al, when quenched from above the critical temperature for the Fe3A1 type of order, always contain the maximum possible amount of FeAl (B2) type of order' (see Fig. 1). Thus when the Fe3A1 superlattice forms, in a 25 at, pet A1 alloy, it does so from an imperfect FeAl structure. The formation of the Fe3Al superlattice has been the subject of several recent X-ray,1, 2 electrical-resistivity,3"6 and dilatometric3 investigations. McQueen and Kuczynski3 concluded that the isotherma1 ordering of Fe3Al, after quenching from 800°C (T,, the critical temperature for order, is 55O°C), takes place by the nucleation and growth of ordered domains. However, Feder and Cahn4 found that the isothermal ordering was complex but more like a homogeneous nucleation process than a nucleation and growth process. Lawley and Cahn2 reported that the degree of order is a continuous function of temperature which is a characteristic of a homogeneous nucleation process. Thus, the evidence is conflicting as to the nature of the Fe3Al ordering reaction. Lipson7 was the first to suggest that ordered domains should exist in the Fe3A1 structure since, as

Jan 1, 1964

By Edward Pesout

The McGill smelter started operations in the year 1907. The smelter furnaces were fired with run-of-mine coal on grates until April 1911, when oil firing was introduced. Oil firing continued until April 1918, when the initial coal-pulverizing plant was started.' Early Pulverizing Plant Various alterations were made to that plant during its operation, one of the more important being in connection with the system for delivering pulverized coal. In order to minimize coal-dust explosions and fires, the return portion of the main delivery line was eliminated in the year 1928. Thereafter coal-dust explosions and fires were greatly reduced. Pulverized coal was prepared at this plant primarily for the reverberatory furnaces, but for several years it was also delivered to the converting plant, roasters and power-plant boilers by a system of auxiliary fans and delivery lines. During the period March 29 to April 8, 1929, one reverberatory furnace was fired with pulverized coal produced by an Aero, type J, unit coal pulverizer with a rated capacity of 5 tons per hour. This machine actually pulverized its rated capacity but the product was too coarse. After certain regulations, a her product was obtained but the pulverizer capacity decreased and this resulted in insufficient coal for efficient furnace operation. Table I gives a comparison of the average screen analyses of the pulverized-coal products from the impact-type unit pulverizer and the regular coal-plant installation. It was definitely proved that this size and type of unit pulverizer could not furnish sufficient coal of proper fineness to give smelting results comparable to that obtained with the regular coal-pulverizing plant. The coal from this unit pulverizer was so coarse that it did not ignite or burn properly and thus did not produce the proper heat for efficient smelting. During the latter part of 1929 and the early part of 1930, experimental work was conducted with a 7-ft. o-in. by 48-in. Hardinge conical ball-mill coal-grinding unit, which was installed alongside a furnace in the reverberatory building. Results obtained from the test run indicated that this unit would furnish sufficient coal of proper fineness for good smelting.

Jan 1, 1947

By J. O. Whiteley, C. Dietz

It is difficult to give a refining outline that may be followed for any and all combinations of the platinum metals; different combinations require different methods of attack. This paper does not pretend to go into all of the reactions of the metals of the platinum group, but will outline the commercial refining of platinum scrap. Typical Platinum Scrap As a concrete case, let us take 100 oz. of miscellaneous scrap, made up of jewelry scrap, dental scrap and laboratory ware. This lot will contain some platinum, palladium, iridium, ruthenium, rhodium, gold, silver and copper. The first problem is to get all of the metals in solution. If the scrap is principally platinum, palladium and gold, a treatment with aqua regia is the course to pursue; but if the scrap contains alloys high in iridium or ruthenium, aqua regia will act too slowly. In the case in hand, we are going to presume that we have scrap high in iridium and ruthenium, and proceed accordingly. Obtaining Residue A Place the scrap, together with six times its weight of granulated test lead, in a solid carbon crucible. This crucible may be placed inside a clay graphite crucible packed with charcoal, to prevent the excessive oxidation of the carbon crucible by the furnace blast. Place a tight cover on the carbon crucible; heat gradually to a good red heat and allow it to soak in the heat for 4 or 5 hr. After the leaded mass is cool, dissolve in dilute nitric acid (1-6) on a steam plate or sand bath. This dissolves practically all of the lead and most of the palladium, silver and copper, together with seme of the platinum and rhodium, and leaves the iridium, ruthenium, gold, and most of the rhodium and platinum as a finely divided residue. Siphon off the clear solution and treat the residue with another portion of dilute nitric acid to insure the solution of the lead and copper. The second nitric acid solution is added to the first, and the residue is filtered on suction and washed thoroughly with hot

Jan 1, 1928

By George C. Stone

The stack gases from regenerative furnaces lare very seldom utilized for the production of steam. If the temperature of the gases is not higher than 300" C. (572" F.) there is no economy in their use for this purpose, as the amount of available heat is very small and the temperature is so little above that of the steam that the interchange is too slow. With higher temperatures of the waste gases, however, good results can be obtained. At the plant of the New Jersey Zinc Co. (of Pa.) at Palmerton there are a number of return tubular boilers, each 6 ft. in diameter and 20 ft. long, with 96 3.5-in. tubes, which are heated by the waste gases from the spelter furnaces. These furnaces have continuous regenerators heating the air only and the stack gases reach the boilers at a temperature of about 450". The gas producers for one of these furnaces require 14 tons of anthracite (a mixture of Nos. 2 and 3 buckwheat), and the waste heat from the furnace gives a little more than 42 h.p. in steam. The boilers are not well adapted for the purpose, as they are much too large for the amount of heat going to them and the area of the tubes is not sufficient to take the gas from two furnaces without causing an objectionable amount of back pressure. The plant was built without any idea of using waste-heat boilers, and it was impossible to place the latter as close to the furnaces as they should be. Furnace and boiler are connected by an underground brick flue in which the temperature of the gas drops about 100°, losing 40 per cent. of its available heat. If the boilers were close to the furnaces the horse power of each would be 70 instead of 42. Even under these unfavorable conditions the boilers have been very advantageous, as one boiler easily supplies the steam necessary for two batteries of producers. With such low gas temperatures the heating surface of the boilers is, of course, not as efficient and the flue areas need to be considerably larger than for coal firing.

Jan 1, 1914

By Charles L. Harness

STRONTIUM is an essential constituent of celestite (strontium sulphate), of the rarer strontianite (strontium carbonate), and of a few very rare minerals. Celestite is the chief ore but strontianite is more valued except for making the purest strontium salts, because of its ease of processing. The public knows strontium mainly as the source of the red flame in fireworks but it has many other uses. PROPERTIES The celestite of commerce is a massive mineral of varying texture: coarsely crystalline, fibrous, bladed, very fine grained or earthy. The color varies greatly with the nature of the impurities but the purer specimens are light blue (Latin, caelum, sky) or white. The strontianite of commerce is a massive mineral, more or less coarsely crystalline. The color varies with the impurities. Distinctive characteristics are effervescence with acids, density (3.68 to 3.71), and crimson strontium flame. A typical British celestite before World War II analyzed: SrSO4, 96.55 pct; SrCO3, 0.17; BaSO4, 0.25; CaSO4, 0.54; MgCO3, 0.15; R20,, 0.90; Si02, 1.38.10 A German strontianite analyzed: SrCO3, 90.9 pct; CaCO3, 7.5; BaCO3, 0.1; Fe2O3, 0.05; A1203, 0.1; SiO2, 0.04; S, 0.1; P, 0.005.10 ORIGIN AND MODE OF OCCURRENCE According to Clarke,9 strontia forms about 0.02 pct of the crust of the earth and is present in most igneous rocks, but in smaller quantities than barium. Under certain conditions, large masses of celestite are deposited from sea water with anhydrite. The presence of large amounts of celestite in some saline deposits and its absence in others suggests that the deposition of celestite depends on whether certain as yet undetermined concentrations of sulphate and chloride ions are reached in the brines. The most extensive of these sedimentary deposits are those of the Keuper (Triassic) in England, of the Zechstein (Permian) in Germany, and of various Cretaceous formations in Texas, Arkansas, and Utah. Of the deposits of southeastern California and western Arizona,

Jan 1, 1949

By E. E. White

I DISAGREE with Mr. Brinsmade on several points, and I will discuss his remarks under the same six topics which he has used. 1. Rate of Interest Earned by Sinking-Fund.-I believe Mr. Brinsmade is confused in his ideas as to the effect of new gold on the interest earned on money. The flood of gold which he mentions certainly should not operate, to increase interest rates, but since it replaces and adds to liquid capital should reduce interest rates and counteract the destruction of liquid capital which he mentions. Furthermore, it is doubtful if the destruction of capital since 1897 by wars and catastrophes has been any greater in proportion than in similar periods before 1897. With regard to savings banks, I would say that only 3 per cent. is allowed on deposits through a large part of the West. As to bonds, they can be bought to yield any rate. of interest desired up to 6 per cent., but, a 5 per. cent. bond is not as safe as a 4 per cent. bond, nor a 4 per cent. bond as safe as a 3 per cent. government security. I do not understand why Mr. Brinsmade says that Mr. Denny's quoted opinion of a 3 per cent. rate is evidently based on English conditions before the Boer War. Certainly there is no reference to the Boer war or to English conditions in Mr. Denny's article. M. Howard Burnham, in his admirable work on mine valuation, says': ". For instance, redemption is taken at 3 per cent., because even 4 per cent. represents a greater risk, as is indicated by the purchase of Government paper to bear only 3 per cent., the great desideratum of the .latter being security." . Again, Mr. Burnham says:2 "The tables are calculated on the assumption that the dividends shall accumulate at 3 per cent. only, as in accordance with the general idea set out elsewhere, a rate greater than 3 per cent. involves appreciable risk with which it were inaccurate to saddle the sinking-fund if risks are to be segregated, this being the basis of all the writer's calculations."

Jan 6, 1914

By R. A. Swalin

IN this paper, the results of an investigation concerning the diffusion of three elements, magnesium, silicon, and molybdenum, in nickel are presented. The work represents a continuation of a diffusion program relating to solute diffusion in nickel. The program has the dual aim of obtaining useful diffusion data and of yielding insight into the factors governing solute diffusion in close-packed metals. The first paper of this series has been published earlier? In both investigations, in agreement with recent results from other laboratories, the activation energies for solute diffusion were found to be close but not identical to that of self-diffusion in the pure solvent in question. In order to obtain valid diffusion data, certain experimental pitfalls recognized only in recent years had to be avoided. Chief among these were the necessity for minimizing short-circuiting diffusion paths such as grain boundaries and the necessity for using low solute concentration gradients. In this series of investigations the following precautions were taken in an attempt to minimize such errors. 1) Samples with large grain sizes, 0.5 to 10 mm, were prepared. 2) The diffusion coefficients were measured at relatively high temperatures, since imperfections such as dislocations play a less important role at such temperatures than at lower temperatures. 3) Alloys containing less than 1 atomic pct were chosen for study. Experimental Work Materials—A diffusion couple technique was employed in the experimental investigation. Briefly, this technique consisted of the following. A diffusion couple was fabricated by placing a flat face of a cylindrically shaped alloy disk against a similar face of a pure nickel disk, and a bond was formed at an intermediate temperature under pressure. The diffusion couple thus fabricated was subjected to a diffusion anneal at higher temperatures for a measured period of time and then sectioned perpendicular to the direction of diffusion. After analyzing the sections for solute concentration the diffusion coefficient was determined from a probability, plot of concentration vs distance from the diffusion interface. Vacuum melted Mond nickel was used in the experimental program. The chemical analysis of this nickel is listed in Table I. Alloys used were prepared

Jan 1, 1958