Search Documents

By Wilbert McBride

Two Alco 3 ½ -ton motor trucks were used by Young Bros. while operating at the Mammoth Collins mine at Shultz, Ariz. One was equipped with an oil tank holding 1,075 gal. and was used for the transportation of "tops." The, other was fitted with a stake body and used to carry machinery, wood, rails, pipe and all classes of miscellaneous supplies. The bodies were made of oak with maple flooring and were attached to the frame of the chassis by U-bolts, to avoid drilling the main members of the frame. Most of the hauling was done from Tucson, a distance of 47;2 miles. During the first. 3 months, part of the road was in very bad condition and the tire cost was excessive. After this part was repaired the road was in fair condition, but never good. There were no excessive grades or bad sand, but wagon ruts, too narrow for the truck wheels and of a different gage, caused heavy tire loss; while chuck holes, sharp curves and stones, both imbedded and loose, were objectionable features. During wet weather the trucks could not get sufficient traction to climb some of the hills and were likely to stick in the mud in certain places, so that no attempt was made to run them unless they were on the road when the rain started. This lost time amounted to about 5 per cent. of the total, but, whenever possible, it was utilized in making minor repairs. The price of gasoline, was from 17 to 21 c. per gal. Rubber tires were used throughout. Drivers were paid $4.50 to $5 per shift, and a return trip to Tucson was counted as two shifts even when made in one day. Drivers were provided with a room in Tucson and were paid for all time lost due to causes beyond their control. Trucks were loaded one way only.

Jan 7, 1916

By D. N. Witman

ONE of the special uses to which the electric furnace has been put recently is the melting of an alloy of nickel and cast iron for the production of electrical-resistance grids. The metal sections of these grids, Fig. 1, are quite uniform for each pattern, but there is, among the various patterns, a variety of thicknesses. The cross sections vary from 1/2 by 3/16 in. to as small as 1/8 by 1/8 in. The electrical resistance f a perfect casting lies within 10 per cent. above or below the fixed listed resistance for each pattern. Good molding is essential to success in the making of these grids, for with absolutely correct metal, a variation of 0.01 in. in width and thickness of section on some of the patterns may mean as much as 12 or 14 per cent. variation in resistance. The service for which these castings are intended demands that the metal, even in the smallest castings, be very soft, showing an open, gray, highly graphitic structure in order that they may be resistant to shock, and stand up well under rough usage. The metal used for this purpose is a gray iron alloyed with 4 to 5 per cent. of nickel, which element, when the composition of the alloy is correct, imparts toughness and pliability to the metal and helps to overcome the tendency of metal to run white and become brittle because of the rapid cooling action of the sand mold. When cold, these castings can be twisted into various shapes, taking a permanent set without breaking. The alloy has approximately double the electrical resistance of ordinary cast iron. The metal specification is as follows: PER CENT. Silicon 2.40 to 2.60 Sulfur Under 0.05 Phosphorus Under 0.08 Manganese Under 0.40 Total carbon 3.60 to 4.00 Nickel 4.00 to 5.00 Copper 0.50 to 0.70

Jan 8, 1921

By D. N. Witman

One of the special uses to which the electric furnace has been put recently is the melting of an alloy of nickel and cast iron for the production of electrical-resistance grids. The metal sections of these grids, Fig. 1, are quite uniform for each pattern, but there is, among the various patterns, a variety of thicknesses. The cross-sections vary from 1/2 by 3/16 in. to as small as 1/8 by 1/8 in. The electrical resistance of a perfect casting lies within 10 per cent. above or below the fixed listed resistance for each pattern. Good molding is essential to success in the making of these grids, for with absolutely correct metal, a variation of 0.01 in. in width and thickness of section on some of the patterns may mean as much as 12 or 14 per cent. variation in resistance. The service for which these castings are intended demands that the metal, even in the smallest castings, be very soft, showing an open, gray, highly graphitic structure, in order that they may be resistant to shock, and stand up well under rough usage. The metal used for this purpose is a gray iron alloyed with 4 to 5 per cent. of nickel, which element, when the composition of the alloy is correct, imparts toughness and pliability to the metal and helps to overcome the tendency of metal to run white and become brittle because of the rapid cooling action of the sand mold. When cold, these castings can be twisted into various shapes, taking a permanent set without breaking. The alloy has approximately double the e1etrical resistance of ordinary cast iron. The metal specification is as follows: Per Cent. Silicon............................................. 2.40 to 2.60 Sulfur............................................. Under 0.05 Phosphorus......................................... Under 0.08 Manganese......................................... Under 0.40 Total carbon....................................... 3.60 to 4.00 Nickel............................................. 4.00 to 5.00 Copper............................................ 0.50 to 0.70

Jan 1, 1922

By B. S. Tani, R. V. Schablaske, M. G. Chasanov

MEASUREMENTS of the solubility of scandium in liquid cadmium from 349" to 606°C by Chasanov, Hunt, Johnson, and eder' led to the isolation and characterization of the intermetallic compound ScCQ. The solid phase found in equilibrium with a saturated solution of scandium in liquid cadmium above 422°C is ScCQ. The equilibrium solid phase below this temperature has not as yet been characterized. Hexagonal needles of ScCG were isolated from a 5 wt pct Sc alloy which had been ice-quenched from 500°C. Free cadmium was leached away from the intermetallic with saturated ammonium nitrate solution. The concentration of cadmium in successive leaches was followed polarographically and the leaching process was terminated when the rate of cadmium dissolution decreased markedly. Chemical analysis of the intermetallic thus isolated is as follows: 11.5 wt pct Sc and 88.3 wt pct Cd. The composition of ScCQ is 11.8 wt pct Sc and 88.2 wt pct Cd. X-ray diffraction powder photographs of ScCds taken in a 114.6-mm Debye-Scherrer camera with CuKa, radiation can be indexed on the basis of a hexagonal nit cell. Lattice coonstants are a. = 6.330 ± 0.001A to 6.324 i 0.001A and co = 4.853 i 0.001A. The a0 has a slight range with the lower value seemingly associated with the cadmium-rich terminus of the phase. With eight atoms in the unit cell the calculated intermetallic density is 7.54 g per cu cm; the density as determined by a liquid-displacement method is 7.7 g per cu cm. Powder-diffraction data for ScCQ are recorded in Table I. Stoichiometry, symmetry, unit-cell dimensions, and the number of atoms per unit cell indicate the MgsCd (D019) type structure for ScCQ; space group is D,&-P6,/mmc. Atomic coordinates are:

Jan 1, 1964

By S. M. Marshall, A. C. Richardson, H. Y. Yancey

A year ago, Marshall and Bird presented a paper in which a new method of measuring the agglutinating power of coal was described.' The procedure used was to determine the strength of a button containing 10 parts sand and one part coal, formed by carbonizing the mixture in a crucible in an electric furnace. The result of the determination was reported as the total weight in grams required to bring about complete destruction of the button. Correlations were shown between the agglutinating value and some of the characteristics of the different coals that were investigated. This agglutinating test has been in use fairly continuously during the past five years for coals of widely differing coking qualities, and it has shown reasonably concordant results accurate enough for commercial use, although there are many features of the test which should have further scientific study. During the past year a study has been made of some coals of low coking strengths, and incidental to the main investigation some data which appear to be of interest and value were obtained on the loss in agglutinating power caused by exposure to the air. Three coals were investigated, all of which were of the Tertiary age; two were from one field in Asia, and one from a field in the United States. The three were similar, as shown by the proximate and ultimate analyses in Table 1 (moisture-free basis). Coals SA and RA generally contain about 5 per cent. moisture and coal P about 3.5 per cent. moisture on the as-received basis. The large difference in the ash contents of the coals, amounting to practically 10 per cent. between SA and RA, and P, makes difficult a direct comparison of their qualities. In the second section of Table 1 the figures have been put upon an ash-free basis., This table shows that these coals are closely alike. The ultimate analyses are almost identical except for the higher nitrogen content of

Jan 1, 1930

By H. W. Paxton, G. M. Pound

A method is outlined for taking into account variation in chemical potential of both components in evaluating capillary effects at growing interfaces. The results are compared with experiment, and seem to be in reasonably good accord for Widman-statten ferrite growing in austenite. ENERY pointed out that during the steady-state growth of phases with a rather small radius of curvature at their advancing edge capillarity cannot be neglected. By proper application of the Laplace equation a correction must be made to the activity gradients down which diffusion occurs. Subsequent workers have concerned themselves with attempts to evaluate specific cases by the use and modification of the principles laid down by Zener.2-5 To solve the problem in its simplest form it is necessary to assume thermodynamic equilibrium at the interface and to select some criterion which will allocate the available free energy between reversible and irreversible processes. Zener chose to assume that the division should be made such that the new phase grew at the maximum rate. Other workers have used the same2,3 or different assumptions, e.g., maximum rate of free-energy dissipation,4 minimum rate of entropy production.5 Li6 has proposed that the "thermokinetic potential" should be a minimum at steady state. The purpose of this presentation is to note that most prior treatments have considered variations due to capillarity only in the chemical potential of the mobile constituent, and that a more consistent treatment must involve a consideration of the variation of chemical potentials of both solute -and sol- vent in a binary system.* As an example, the way in which this arises for ferrite growing from austenite may be illustrated by reference to Fig. l(a). The line OABC shows a typical variation of carbon activity with composition at one atmosphere pressure (at a transformation temperature below A3). In the tip of a growing ferrite plate with a hemi-cylindricab leading edge of radius ?, the pressure due to capillarity is*

Jan 1, 1963

By R. W. Smith. Discussion by D. Watson, R. M. Manser

D. Wotson, R. M. Monser (Watten Spring Laboratory, Stevenage, Herts., U. K.) - This is a valuable and interesting paper and will make an important contribution to the development of a general theory of silicate flotation. In particular the dominance of surface reactions which produce fluosilicic acid and its ions has been convincingly demonstrated. In a paper to be published shortly, however, we offer some evidence which is not consistent with the feldspar activation theory proposed by Prof. Smith. This theory, given in Eqs. 17-20, suggests that activation takes place through the exchange of SiF6 ions for OH- at aluminum sites. This results in a negatively charged site facilitating adsorption of RNH3 Firstly, we have determined the flotation response (using the vacuum flotation technique) and the adsorption of dodecylamine on a natural feldspar (albite) and on the same feldspar after washing with perchloric acid at pH3. This pre-treatment was shown to remove surface adjacent aluminum atoms. It was found that although the acid washed feldspar floated much less easily than the untreated sample, the function of fluoride ion - giving activation over the pH range 4-6.5-was preserved. Moreover, the amount of dodecylamine adsorbed either with or without fluoride present is little affected by acid-washing, despite the depression caused by this treatment. This suggests that surface aluminum atoms can be of little importance in the fluoride activation mechanism. Secondly, we have determined the changes in solution concentration of F- and H+ (or OH-) accompanying reaction of the surface with fluoride ion. The ratio of H+ lost from solution to F- lost is high, ranging from 6.9 at pH4 to 1.0 at pH 7.5. This is consistent with reaction of HF (6 molecules for every Si removed) at the surface, producing SiFi-ions, but not with the re-adsorption of these ions.

Jan 1, 1967

By L. I. Cothern

THE introduction of mechanized mining has created a demand for long working faces. It has also prompted mining men to contest the old theory that longwall methods can be used only where roof conditions are ideal and where pack-wall material is plentiful. "Longwall" as used in this paper means "modified longwall," "semi-longwall," or any of the various "wall" or "long-face" methods of mining. Many mines are now using long conveyor faces that differ only in their methods of development, types of roof support and method of loading coal onto the conveyor. Some types of longwall operations are being carried on successfully under conditions heretofore considered impossible by men experienced in longwall mining. With possibly one or two exceptions, long-face methods in Alabama are a direct result of the need for lower mining costs. The advantages over room-and-pillar systems were clearly expressed in an article by Messrs. Fies and Lacy of the DeBardeleben Coal Corporation1 as follows: (1) increased tonnage per miner; (2) increased percentage of lump coal; (3) reduction in cost of development; (4) elimination of the cost of room yardage; (5) reduction in the cost of haulage, from ability to use larger cars; (6) reduction in the cost of machine cutting; (7) reduction in cost for tracks; (8) reduction in the cost of deadwork; (9) reduction in the cost of supervision. An attempt on the part of the operator to gain these, advantages by changing from room-and-pillar to longwall requires considerable courage, and credit should be given to those men who have done their bit to meet the competition of rival fuels. The initiatory problems to be solved are in reference to: (1) retreating or advancing system, (2) length of wall, (3) method of roof support, (4) method of entry development, (5) type of conveyor or loader, (6) hand vs. machine loading (onto conveyors), (7) hand vs. machine loading in entries, (8) control of roof pressure,

Jan 1, 1940

By Arthur Knapp

Oil-well depletion curves, to be of value, should show when a well or lease may no longer be operated at a profit. The difference, at any time, between the total expenditures and the total income of a lease or well may be called the lease status. Plotting this lease status against time will give a curve subject to more accurate and different interpretations than the barrels-time curves. According to the hypothetical barrels-time curves shown in Fig. 1, well A, at the end of 16 mo., is producing twice as much oil as well B and will continue to produce for another year whereas well B will cease producing in about 6 months. Data fob Lease Status-time or Dollars-timb Curve Time Lease Months Status Lease purchased for $3000.............................. 0 — $ 3,000 No expenses chargeable to lease for 3 mo................. 2 — 3,000 Well A is started; cost of drilling for month is $16,000..... 3 — 19,000 Well is completed at additional cost of $10,000............ 4 - 29,000 Well A is brought in and flows 10,000 bbl. first month (we Fig. 1). Necessary to invest in tanks, boilers, pipe lines, etc.; difference between expenditures and receipts gives profit for month of $5,000............................ 5 — 24,000 Investment is small, cost of operating well A is small, so profits are $15,000................................... 6 — 9,000 Well ceases to flow so there is additional investment for pumping equipment and additional operating expense; net earnings from 6,000 bbl. of oil produced is $4,000. 7 ... Lease operation nor becomes normal and curve becomes smooth........................................... 8 — 500 9 2,000 10 4,500 11 6,000 12 7,700 13 8,700 14 9,000 15 9,500 16 10,000 A hypothetical lease status-time, or dollars-time, curve of this lease is shown in Fig. 2. At zero time, the lease is purchased for $3000, which is plotted below the zero dollar line, All subsequent entries are plotted

Jan 1, 1921

By W. L. McMorris

The Convertol process was first described in Germany by Muschenborn' in 1952. In the U. S. Fraser' reported this new process in 1953, and Brisse and McMorris" presented the results of a Convertol pilot plant at the Alpheus preparation plant in Gary, W. Va., illustrating the mechanics of the process by a series of sketches. The purpose of the present investigation was threefold: 1) to determine the relative effectiveness of various oils and hydrocarbons for recovering coal by the Convertol process, 2) to ascertain the behavior of coal pulps in this process under various operational conditions, and 3) to compare Convertol with flotation in the recovery of fine coals. APPARATUS, PROCEDURE, AND COAL SAMPLES In laboratory work with the Convertol process a Waring Blender equipped with a speed-regulating rheostat was used for wetting, conditioning, inversion, and retention of the coal pulp. A 5-in. International centrifuge was adapted to dewater the agglomerated clean coal product by installation of a 100-mesh screen inside the regular bronze basket of the centrifuge. Except where otherwise stated, the Convertol testing was performed by the following steps: 1) A 450 to 500-cc coal slurry, containing 24 pct by weight of solids, was agitated in the blender for 10 min at 100 rpm to insure complete wetting and mixing. 2) Eight percent by weight of oil was added to the coal slurry in the blender and agitated for 1 min at 11,000 rpm to result in the phase inversion or agglomeration of oil-coated coal particles. 3) The agglomerated coal slurry was poured onto a 100-mesh sieve and wet-screened for about 2 min to remove most of the ash and some of the water. 4) The material remaining on the screen was transferred into the centrifuge for final dewatering. 5) A portion of the clean coal was immediately weighed out for moisture determination, while the

Jan 1, 1960

By Edgar Newhouse

THE lead smeltery at East Helena, Mont., controlled by the American Smelting & Refining Co. since 1899, has been in continuous operation for the past 25 years. Most of the old smelting and roasting practices have been superseded by newer and more modern methods, but on account of the difficulties involved in changing the original construction, some of the methods in use of handling materials are not the most modern. This plant, however, is particularly interesting as being one of the few essentially lead smelteries in the United States. At Federal, Ill., Collinsville, Herculaneum, and possibly other places, similar work is being done, but it is doubtful whether any of them produces as' much lead as the East Helena plant, whose monthly production averages 6,500 tons. The situation, 5 miles east of Helena, is convenient to both the Great Northern and Northern Pacific railroads, while the electric power is obtained from Canyon Ferry, 12 miles east on the Missouri river. Local quarries supply the requisite amount of lime rock, Which the contracts require to be crushed to 5 in. Of the 450 men on the monthly pay roll, a census showed 200 Austrians, 110 Americans, and 30 Italians, the balance being made up of miscellaneous nationalities. The ore supply is mainly derived from the Coeur d'Alêne mines in Idaho, and consists of crude ore, coarse and fine concentrates, middlings, and slimes. About one-half of the total output of the Coeur d'Alêne camp is sent to East Helena. An average analysis of these ores gives approximately 40 per cent. lead and 11 per cent. sulphur. Local shipments, varying, from month to month, are mostly highly siliceous gold and silver ores carrying little lead. Small shippers, leasers of old mines, and prospectors are very numerous throughout Montana, and it is the policy of the company to encourage these men by every possible means, including the free sampling and analysis of their ores and aid in the development of their mines and prospects whenever their results show promise.

Jan 8, 1914

By Hans Lundberg

BASED upon an instrumental improvement, a new development has taken place in the art of electrical prospecting, and some remarkable results have already been obtained with regard to potential exploration. In order to visualize the importance of this development, it is deemed advisable to review briefly the fundamental facts about potential surveys. Potential exploration may be carried out qualitatively or quantitatively. Qualitative investigations are made by determining and plotting on a map points of equal potential, whereby any anomalies are revealed, without, however, much clue to their magnitude. Quantitative investigations determine the variations of potential or potential drop, and thus show not only the location of the anomalies, but also their magnitude. Figs. 1 to 6 illustrate the influence of simple types of ground inhomo-geneities, assuming one effective exciter potential only. Such a condition can be closely realized by connecting an electric current source to two electrodes, one of which, is located at a great distance. Assuming uniform ground resistivity, the resultant potential distribution may be represented by concentric spheres. Any change from the normal condition causes a characteristic distortion of the spheres, which becomes different for different types of resistivity variation. The series of Figs. la to 6a illustrates schematically results of qualitative investigations and series 1b to 6b results of quantitative investigations. Figs. 1 and 2 picture the well-known case of local resistivity variations normally encountered in ore prospecting. Figs. 3 and 4 show the reactions caused by more or less vertical resistivity contacts and Figs. 5 and. 6 refer to the problem of ground-water and bedrock investigations where the resistivity contact is horizontal or nearly so. It is evident from Figs. 5a and 6a that qualitative measurements do not permit an identification of such general geological features as widespread horizontal strata, because the resultant contraction or expansion of the equipotential circles at the surface cannot be recognized without quantitative determinations. On the other hand, qualitative measurements are well suited for the exploration of local or lateral resistivity

Jan 1, 1931

By C. P. Melloy

INTRODUCTION Ventilation practice at Isa Mine has been evolving since underground mining began in 1931. Much fundamental work has been conducted and reported regarding the primary ventilation system [Mathews K.E. et a1 (1967) and Brown J.R., Fisher T.H., Gibson K.L. (1979) 1. However, ventilation networks for subsystems such as open stopes, have evolved with experience. This paper outlines current ventilation practice for open stoping. Mount Isa Mine The mine is located in semi-arid North-West Queensland, Australia, and currently produces 20 000 tonnes of copper ore and 10 000 tonnes of silver-lead-zinc ore daily in each five day working week. Mining extends over a north-south strike length of 3.5 km with a maximum width across dip approaching 1 km, and is to a depth of 960 m (Figure 1). At present approximately 90% of the mine's copper production is from the 1100 Orebody, which contains ore reserves of 121 million tonnes of 3.2% copper. Open stoping is currently the mining method employed, and is used for primary stoping and pillar recovery adjacent to cement fill walls. The development of stoping methods in the 1100 Orebody has been documented by Kirkby R.W., Blair J.R., and Hutton R.C. (19781, Hornsby B. and Sullivan B.J. (1978), and Alexander E.G. and Fabjanczyk M.W (1981). As many as thirteen open stopes may be producing concurrently in the Orebody (Figure 2). The multiple silver-lead-zinc orebodies containing reserves of 54 million tonnes of 150 g/t silver, 6.4% lead and 6.5% zinc, are mined by open stoping, and cut and fill techniques. These methods have been documented by Goddard I.A. and Bridges M.C. (1977 1, and Goddard I. A. (1981 1. Only the ventilation of the 1100 Orebody open stopes will be discussed. However, the same ventilation philosophy is employed in open stope design in the lead orebodies.

Jan 1, 1981

By Lucius W. Mayer

The iron-mines of the Ilsede Hutte Co. are at a town called Peine, about 20 miles east of the city of Hanover, on the railroad to Brunswick (Braunschweig). Hanover, the capital of the province, is a military city, of approximately 250,000 inhabitants, and Brunswick, 33 miles to the westward, has half this number. The mines here described are located in a hamlet called Bulten. The Ilsede Hutte Co. operates two mines, 1.5 miles apart, in this district, Gruber Bulten Adenstadt and Gruber Lengede Bodenstadt. It also operates an iron-mine north of Hanover, known as Eiserhaven, and one in the Harz mountains, the Georg Friedrich, at Grauhof. At Bulten a coarse conglomerate, a, Figs. 1 and 2, contains nodules of limonite, cemented together by calcium phosphate. The ore contains Fe, 25 to 45; Mn, 3 to 4; P, 0.6 to 1.4; '5, 0.02 to 0.09; and CaCO,, 40 per cent. Directly above the conglomerate is limestone, 6, followed by a mixture of clay and sand, c. Below the conglomerate is a hard clay floor, d. The ore-body, from 10 to 12 km. long, and from 3 to 4 km. wide, has a maximum thickness of 20 m. It dips approximately 10" S.E., and strikes K 45° E. Diamond-drill prospecting shows that the thickness diminishes to 1 m. as the end of the deposit is approached to the northward. At this point the deposit is 250 m. below the surface. In Fig. 2, the arrow, A, indicates the general direction of the work along the face, a, which is carried forward in a straight line for its entire length. At B, a train is approaching, which has come from the bench-track, shown at C, by a circuitous route, and is dumping the overburden behind the face, in the space left by the excavated rock. Formerly the work at this mine mas essentially open-cut, the deposit having a very strong outcrop. Figs. 1 and 2 show also

Jan 1, 1909

By T. F. Bower, M. C. Flemings

The classical explanation for formation of the fine equiaxed "chill zone " in ingot solidification is that local supercooling near the chill wall causes copious nucleation in this region. This work indicates, however, that convection is an essential element in formation of the chill zone. In the absence of convection, no chill zone forms even though rate of. heat extraction is extremely vapid. Alloy studied was Al-l.5 pct Cu alloy solidified against a copper chill wall. When solidification was initiated at the chill wall in absence of. cor-vection, surface grain size was large (>I cm diam). When it was initiated in the presence of convection, it was fine (<0.05 cm diam). It is concluded that some form of "crystal multiplication" plays an important role in formation of the chill zone. INGOT macrostructures are generally classed as containing one or more of the three zones: "chill zone", "columnar zone", and central "equiaxed zone". These three zones are sketched in Fig. 1; their origin has been discussed in some detail.&apos;-&apos; The classical explanation for formation of the chill zone is that supercooling occurs in the region of liquid metal adjacent the mold wall, and copious nu-cleation then takes place in this region forming numerous small crystals. The columnar region then results by growth of favorably oriented grains (den-drites) which crowd out their less favorably oriented neighbors."5 The mechanism of the columnar-equiaxed transition has been the subject of considerable interest. The generally accepted mechanism, until recently, was that constitutional supercooling developed in front of the growing columnar grains with eventual nucleation of new, equiaxed, grains ahead of the growing solid front.&apos; Recently, it became evident this explanation was not completely satisfactory and it is now evident that "crystal multiplication" plays an important role. This crystal multiplication occurs by separation of dendrite arms from growing dendrites,8?"&apos; and has been shown to be strongly influenced by convection.6, 10-13 Reduced convection results, for a given alloy, in longer columnar zone, larger columnar grains, and larger equiaxed grains.7, 12

Jan 1, 1968

By J. Gordon Parr, A. J. Goldak

OgdEN et al.1 and Bumps et al.2 suggested that the solubility of aluminum in a titanium extended to 30 pct.* Sagcl,3 Clark and Terry,4 Anderko et al.,5 Ence and Margolin6 and Saulnier and croutzelles,7 subsequently proposed the existence of an intermetallic compound in the region of 25 pct Al. Although Anderko et al.5 suggested that the structure of this phase, Ti3Al, was of the DO,, (Ni3Sn) type, their conclusion was based only upon the results of a powder photograph that included reflections from ? = 0 to ?= 27° (CuK),some of which were reported to be indistinct. Ence and Margolin,6 referring to a 25 pct alloy (but without indicating whether the figure referred to weight or atomic pct) stated: "The structure of Ti2Al is isomorphous with Ti3Sn DO19, as pointed out by Pietrokowsky". But the point was not proven, because Ence and Margolin did not report values of calculated intensities of Ti2Al with the DO,, structure. In fact, the observed intensities they reported are in poor agreement with the values we calculate for DO19 (see Table I). Saulnier and croutzelle7 concluded, on the basis of electron micrography and microdiffraction studies, that the structure of the 25 pct A1 alloy was ordered hexagonal. Our purpose has been to unequivocally determine the Ti3Al structure. Alloys containing 25 pct Al were prepared from iodide titanium and spectrographic standard aluminum by levitation melting. The levitation chamber was evacuated to 10-6 mm Hg before filling with 99.999 + pct A. After casting, the alloy was chilled to liquid air temperature and crushed to -200 mesh in a percussion mortar. The powder, wrapped in molybdenum foil, was annealed (by induction heating) at 1000 "C for 2 hr in the argon atmosphere of the levitation chamber. No sublimate was seen on the foil or elsewhere, and therefore the assumption is

Jan 1, 1962

By Arthur R. Kommel, Robert F. Mehl, Gerhard Derge

The orientation relationships resulting from allotropic transformations and the formation of segregate structures in metals and alloys have been the subject of the eight earlier papers in this series&apos;. A brief summary of orientation studies has also been given by Sachs2. A survey of these papers discloses that the factors that determine the orientation relationship of a precipitated phase to its parent solid solution, as well as the outward form and appearance of the new phase, are not completely understood. It is now evident that crystallographically analogous systems, as a rule, exhibit the same type of Widmanstatten figure and orientation relations, so that useful information is not to be expected from examination of a new alloy involving lattice combinations of which the orientation relationships are already known. Therefore, the determination of the relations existing between lattice types that have not already been studied seems to be the most promising mode of attack upon the problem; both of the systems reported in this paper represent new combinations of lattice types. A. The Mg-Mg2Sn System The magnesium-tin equilibrium diagram given by Hansen3 shows the phase Mg2Sn to be the only intermediate phase. The solid solubility of Sn in Mg decreases from 14.8 weight per cent at the eutectic temperature, 561&apos; C., to 2.3 per cent at 450°, while no solid solubility of Mg in Mg2Sn has been observed. The crystal structur: of Mg is close-packed hexagonal with a0 = 3.202 A. and co = 5.199 A.4, while Mg2Sn is of the CaF2 type with a. = 6.78 A., with four molecules in a unit ce115,6. Alloys from two different sources have been used: (1) those supplied by the Dow Chemical Co., which contain 6 and 8 weight per cent Sn, and (2) those prepared in this laboratory, containing 8 and 13.5 per cent Sn. The latter were made from Dow high-purity Mg and Baker chemically

Jan 1, 1937

Frank Firmstone, Easton, Pa. (communication to the Secretary*) : It may not be amiss to point out that the top-pressure in iron blast-furnaces is largely affected by variations in the temperature of the gas. I find in my note-books, cases in which the pressure was from 9.25 to 9.5 in. of water when the material in the furnace was low (after dinner-hour), which fell to from 8 to 8.5 in., when the furnace was again full, and the gas consequently cooled. The chief cause for this effect is, that, at the higher temperature, there is a decrease in the weight of the gas in the descending-leg of the siphon formed by the down-comer and the chimneys. It does not seem probable that there is any direct relation between top-pressure and quantity of flue-dirt. Top-pressure, at any given moment, measures the " head " necessary to discharge the gas then passing, against the resistances of pipes, valves, etc., in the gas-conduits between the top of the furnace and the mouths of the chimneys, and can be increased at will by closing, more or less, the valves, or dampers, at the stoves and the boilers. The question of relation between top-pressure and flue-dirt can be settled very easily by direct experiment, working alternately with gas-valves open, and partly closed, and noting the top-pressures and the respective quantities of fluedirt collected. The quantities of fine ore blown away, as shown by Mr. Grammer&apos;s tables, are astonishing to one who has had no actual experience with Mesabi ore and hard driving. Flue-dirt, in the sense in which he uses the term, was unknown at anthracite furnaces so long as the working was normal; when it did occur, it was always an incident of scaffolding and bad work, and was no doubt caused by an increase in the velocity

Jan 1, 1904

By F. J. Tuck

THE Hayden mill of the Ray Mines Division, Kennecott Copper Corporation, is now equipped with two 9 by 12-ft. rod mills having a daily capacity of 6000 tons of coarse-crushing plant product from the mine. These two mills crush a 3/4-in. product to approximately 19 per cent on 14 mesh, with only one pass through the mills. Each rod mill has taken the place of four sets of 42-in. Garfield rolls with their attendant screens, and is making a product for the fine-grinding department comparable to that formerly made by rolls in closed circuit with screens. The rod mills are lined with wave-type liners of white iron, varying in thickness from 2 to 3 in. The shell and end liners last approximately 600 to 700 clays. Manganese-steel lifter bars, 3 5/8 in. thick, are used, spaced about 11 in. apart, and they give a life of 350 to 450 clays. Fig. 1 shows the general design and thickness of the wave-type liners and lifter bars; 1 1/2 -in. liner bolts are used to fasten the lifter bars to the shell. The shell liners are held in place by the tapered lifter bars. A ¾-in. wood hacking is used between the shell and the liners. The rod-mill scoop has removable manganese-steel lips, which last 250 to 300 days. The scoop proper has shown some wear in spots; and these spots have been protected by rubber bolted over them. Water and milk of lime are added to the elevator feeding the mill, but not enough water to cause a pounding of the rods against the shell. Roughly, the water added amounts to 2.5 to 33 per cent of the ore. Addi-tional water is added to the mill discharge to facilitate distribution to the classifier bowls in the fine-grinding department.

Jan 1, 1938

By Ian J. Smalley

"Quickclay is an extreme case, it is by far the most mobile of all the common solid materials on the earth&apos;s surface. It has both a high water content and a mineral texture that allows it to flow with the utmost ease. A mass of quickclay that has lain undisturbed for thousands of years can be jarred into motion by any sudden shock." The quotation is from the paper by Kerr called, "Quickclay," which was published in Scientific American in 1963. This was probably the most widely read paper on quickclay ever published. It was reprinted by Fred Betz in his Benchmark collection on Environmental Geology (BM 25), A quickclay is an extremely sensitive soil. The sensitivity parameter is produced by dividing the undisturbed shear strength by the remoulded shear strength. If a value greater than 50 is obtained, then the soil can be classified as a quickclay. True quickclays are characterized by a very low remoulded strength of the order of 0.5 kPa. The classic quickclays are found in Scandinavia and Eastern Canada, but the 1964 Alaska earthquake revealed a considerable quick¬clay deposit underlying the town of Anchorage. This was discussed in a classic paper by Kerr and Drew in Engineering Geology in 1967. The Kerr views on quickclays were perhaps most clearly expressed in the paper with Liebling in Geol. Soc. Amer. Bull. in 1965. They suggested that the major critical conditions which contribute to quickclay movement are: substantial quantities of layer lattice silicates of colloidal size (about 40% or more by dry weight), sub¬stantial pore water (44%), a reduction in electrolyte concentration below 5 g/l of salt, and addition of a dispersant. There is still discussion and disagreement about the nature of quickclays and the mechanisms of quickclay slides; the "clay mineral"-based views favored by Kerr still find support, although an alternative "primary mineral" view suggests that it is the finely ground primary minerals

Jan 1, 1985