Search Documents

By D. Hnrrington

THE Dust Symposium was attended by approximately 100 persons, nearly all of whom remained from the starting hour (2 p. m.) until the use of the auditorium was demanded for another meeting at 5:30 p. in. In calling the meeting to order, D. Harrington made a few remarks as to the importance of the health dust problem in mining as well as in general industry and expressed gratification that the subject is now out in the open and that mining people are desirous of ascertaining the facts. B. F. Tillson acted as chairman of the meeting. The milling executive who desires to know what to do to prevent his workers from being unduly exposed to the dust hazard can get much out of the paper by D. E. Cummings, who has been doing much work in mines trying to keep -the dust in the air within safe limits. His recommendations indicate that the main protection of the worker in mines is by adequate ventilation, supplemented by the extensive use of water in drilling, as well as in water curtaining to condition air both in regard to dust content and to temperatures. Blasting was shown to be one of the chief causes for dust and it was recommended that whenever feasible all blasting should be delayed to the end of the working shift.

Jan 1, 1935

By W. B. Lilienthal, J. C. Melrose

The application of Bingham's law to the behavior of drilling fluids in a rotational viscometer permits the expression of viscometric data in terms of plastic viscosity and yield value, the flow properties of a plastic fluid. A commercially available rotational viscometer is described, and when modified to a multispeed type viscometer, is shown to provide a simple and convenient instrument for the measurement of these properties both in the laboratory and in the field. The data obtained are shown to be useful in defining and understanding mud control problems relating to chemical treatment and to the hydro-dynamic behavior of muds. INTRODUCTION The highly complex drilling fluids which are required for deep drilling often give rise to new and unusual mud control problems. Rapid and economic solutions to these problems may require, on the one hand, better understanding of the changes which contaminants and chemical treating agents produce in the colloidal and inert solids of the mud, or, on the other hand, closer control of the hydrodynamic behavior of the mud. The latter objective obviously can be achieved only if a correct rheological analysis of the flow behavior of drilling muds is available and if this is accompanied by the appropriate rheological measurements. The purpose of this paper is to describe such measurements in the field, and to show how the resulting data can be of value in solving difficult mud control problems. It is now generally recognized that Bingham's law of plastic flow can be utilized in describing the hydrodynamic behavior of drilling fluids in the non-turbulent flow range. Beck, Nuss, and Dunn' have recently applied this law to the flow of mud in small pipes, and Rogers2 has reviewed the rather extensive literature on this subject. So far, however, the use of Bingham's law has been restricted to the analysis of mud flow in pipes or capillary tubes, and it has not been directly applied to the flow in rotational viscometers. In the work to be reprted, the Reiner-Riwlin3 equation for the flow of a plastic fluid in a rotational viscometer has been utilized to permit the expression of multispeed viscometric data in terms of plastic viscosity and yield value. the two absolute flow properties of a plastic fluid. With regard to the application of these measurements, the calculation of the relationship between pumping rate and pressure drop, both in the drill pipe and annular space, has long been a subject of interest. Beck, Nuss, and Dunn,' following Caldwell and Babbitt: base their calculations for non-turbulent flow on Buckingham's integration of Bingham's law for pipe flow and measurements of the plastic viscosity (rigidity in their terminology) and yield value. In the case of turbulent flow, Fanning's equation is employed, and the pressure drop is relatively insensitive to the flow properties of the mud. Since flow in the drill pipe is likely to be turbulent at usual circulation rates, the plastic flow properties will chiefly influence the pressure drop in the annular space. As pointed out by Beck,' the control of this component of the total pressure drop may be of special importance where lost circulation problems are encountered. Other hydrodynamic problems to which it should be possible to apply measurements of the plastic flow properties include predictions of the velocity distribution in non-turbulent flow and the critical velocity for transition to turbulence. Plastic viscosity and yield value. as abmlute flow propertie.;, will reflect the colloidal or surface-active behavior of the solids present in drilling fluids. Measurements of these properties should therefore find application in developing a better understanding of such behavior and in characterizing the type and condition of these solids. Garrison and ten Brink have utilized multispeed viscometric data in this manner. although their measurements were not expressed in terms of the absolute flow properties. In connection with the application of these measurements, it should be recognized that the presently used one-point viscosity measurements are relative in nature. The API Stormer 600-rpm measurement, for example. is a function of both plastic viscosity and yield value, as well as mud weight, and will often be misleading when its application to mud control problems is attempted. NOMENCLATURE, UNITS, AND DEFINITIONS In Fig. 1 an idealized plot is given of the flow variables involved in any viscometric measurement. It is seen that the flow behavior of plastic fluids is characterized by two constants — plastic viscosity, µp, and yield value, F. Other workers hate used the term rigidity for plastic viscosity or the term mobility for its reciprocal. The term plastic viscosity, however, emphasizes the close relation this property bears to the viscosity of a true fluid and is expressed in the familiar viscosity units of centipoises. The yield value is expressed in lbs/100 sq ft, the units adopted for gel strength measurements with the APT shearometer. Definitions of these properties based on rheological or macrc)scopic flow considerations follow from Fig. 1. The plastic viscosity of a substance obeying Bingham's equation is defined

Jan 1, 1951

By J. C. Melrose, W. B. Lilienthal

The application of Bingham's law to the behavior of drilling fluids in a rotational viscometer permits the expression of viscometric data in terms of plastic viscosity and yield value, the flow properties of a plastic fluid. A commercially available rotational viscometer is described, and when modified to a multispeed type viscometer, is shown to provide a simple and convenient instrument for the measurement of these properties both in the laboratory and in the field. The data obtained are shown to be useful in defining and understanding mud control problems relating to chemical treatment and to the hydro-dynamic behavior of muds. INTRODUCTION The highly complex drilling fluids which are required for deep drilling often give rise to new and unusual mud control problems. Rapid and economic solutions to these problems may require, on the one hand, better understanding of the changes which contaminants and chemical treating agents produce in the colloidal and inert solids of the mud, or, on the other hand, closer control of the hydrodynamic behavior of the mud. The latter objective obviously can be achieved only if a correct rheological analysis of the flow behavior of drilling muds is available and if this is accompanied by the appropriate rheological measurements. The purpose of this paper is to describe such measurements in the field, and to show how the resulting data can be of value in solving difficult mud control problems. It is now generally recognized that Bingham's law of plastic flow can be utilized in describing the hydrodynamic behavior of drilling fluids in the non-turbulent flow range. Beck, Nuss, and Dunn' have recently applied this law to the flow of mud in small pipes, and Rogers2 has reviewed the rather extensive literature on this subject. So far, however, the use of Bingham's law has been restricted to the analysis of mud flow in pipes or capillary tubes, and it has not been directly applied to the flow in rotational viscometers. In the work to be reprted, the Reiner-Riwlin3 equation for the flow of a plastic fluid in a rotational viscometer has been utilized to permit the expression of multispeed viscometric data in terms of plastic viscosity and yield value. the two absolute flow properties of a plastic fluid. With regard to the application of these measurements, the calculation of the relationship between pumping rate and pressure drop, both in the drill pipe and annular space, has long been a subject of interest. Beck, Nuss, and Dunn,' following Caldwell and Babbitt: base their calculations for non-turbulent flow on Buckingham's integration of Bingham's law for pipe flow and measurements of the plastic viscosity (rigidity in their terminology) and yield value. In the case of turbulent flow, Fanning's equation is employed, and the pressure drop is relatively insensitive to the flow properties of the mud. Since flow in the drill pipe is likely to be turbulent at usual circulation rates, the plastic flow properties will chiefly influence the pressure drop in the annular space. As pointed out by Beck,' the control of this component of the total pressure drop may be of special importance where lost circulation problems are encountered. Other hydrodynamic problems to which it should be possible to apply measurements of the plastic flow properties include predictions of the velocity distribution in non-turbulent flow and the critical velocity for transition to turbulence. Plastic viscosity and yield value. as abmlute flow propertie.;, will reflect the colloidal or surface-active behavior of the solids present in drilling fluids. Measurements of these properties should therefore find application in developing a better understanding of such behavior and in characterizing the type and condition of these solids. Garrison and ten Brink have utilized multispeed viscometric data in this manner. although their measurements were not expressed in terms of the absolute flow properties. In connection with the application of these measurements, it should be recognized that the presently used one-point viscosity measurements are relative in nature. The API Stormer 600-rpm measurement, for example. is a function of both plastic viscosity and yield value, as well as mud weight, and will often be misleading when its application to mud control problems is attempted. NOMENCLATURE, UNITS, AND DEFINITIONS In Fig. 1 an idealized plot is given of the flow variables involved in any viscometric measurement. It is seen that the flow behavior of plastic fluids is characterized by two constants — plastic viscosity, µp, and yield value, F. Other workers hate used the term rigidity for plastic viscosity or the term mobility for its reciprocal. The term plastic viscosity, however, emphasizes the close relation this property bears to the viscosity of a true fluid and is expressed in the familiar viscosity units of centipoises. The yield value is expressed in lbs/100 sq ft, the units adopted for gel strength measurements with the APT shearometer. Definitions of these properties based on rheological or macrc)scopic flow considerations follow from Fig. 1. The plastic viscosity of a substance obeying Bingham's equation is defined

Jan 1, 1951

INTRODUCTION TO SAMPLING THEORY Before specifically discussing mineral sampling and sampling procedures, let us briefly consider broader and more universal concepts of modem sampling theory. A sample is de- fined as a representative part or a single item from a larger whole, being drawn for purpose of inspection or shown as evidence of quality. In modem theory the sample is a part of a statistical population whose properties are studied to gain information about the whole. The theory of sampling is built around the concept that if enough representative units of a larger overall population are selected without bias, the average value of the units will approximate that of the total population. Modem theory attempts to answer the question of how many samples are enough, given certain limits and constraints, and seeks to apply methods of sample selection and of estimation that provide, at the lowest possible cost, estimates that are precise enough for the purposes at issue. In order to meet these objectives the designer of a sample survey must rely heavily upon statistical theory. Statistics has been defined as the collection, presentation, analysis, and interpretation of numerical data. Statistical methods are primarily concerned with making valid inferences about a population based upon samples taken from the population. For most statistical applications, the total sample is in terms of number of items, attributes, or things; whereas mineral samples are usually in terms of weight or volume of mineral particles. Certain steps are involved in a well designed sample survey without regard to the particular field of application. Because the desired characteristics of an unmined mineral deposit can- not be known other than by sampling, we will consider these principle steps in terms of a mineral sample survey: 1) Clear definition of the objectives of the survey. In the case of mineral sampling this step is so apparent as to be almost ridiculous. However, it is surprising how often the overall objective of a sampling program is overlooked when decisions are made on a day-today basis. 2) Definition of the population to be sampled. The word population is used to designate the aggregate from which the sample is chosen. A sampling program may be designed to determine the grade of a single stope within a mine, the grade of a particular zone within a complex ore body, or the total value and extent of a mineral deposit. Since mineral sampling is usually done in phases, it is well to

Jan 1, 1980

By Richard Ely

Conservation Means Preservation, Improvement, Justice CONSERVATION, narrowly and strictly considered, means the preservation in unimpaired efficiency of the resources of the earth; or in a condition so nearly unimpaired as the nature of the case, or wise exhaustion, admits. And broadly considered, it means more than the word itself implies, for it naturally includes an examination of methods whereby the natural inheritance of the human race. may he improved; and still more broadly considered-and as used in popular discussion-it includes a treatment of the effects of productive conservation measures upon distribution. We shall give our attention briefly to the main points in this informal definition before we pass on to the thesis that conservation is largely a matter of property relations-that a wise conservation policy means wise property relations. Preservation of Natural Resources First, conservation suggests simply preservation, and, in the treatment of the subject which we have had in the United States, emphasis has been laid upon the past and present waste of natural resources and upon the means of putting a stop to this waste. The forests have been depleted; soil has been washed by rapidly flowing surface water from mountain sides. These rapidly flowing waters have produced high streams and devastating inundations, followed by low streams and impeded navigation. The forests have, moreover, been so removed as to bring great danger of fire, and destructive conflagrations have resulted in large waste of resources, including in some cases a destruction of the humus, supplying essential elements in the fertile soil. As a remedy we must have measures to reforest mountain sides, and this means large social control, very frequently taking the form of public ownership and management; but in addition we always find actual and proposed

Jan 2, 1916

By D. A. Woodford

A number of observations have now been reported where the steady-state creep rate is apparently linearly dependent on the applied stress at high temperature and low stresses. This results in a creep rate greater than that predicted by extrapolation of high-stress data and has obvious practical implications. However, some of these observations are open to question. For example, the analysis by Harris and Partridge17 of the data of Greenfield et a1.18 was dependent on strain rates which, according to the original authors, were too low to be measured. Dr. Bernstein appears to have demonstrated a linear stress dependence at low stresses in two zirconium alloys. There are, however, a number of discrepancies in his treatment of the data and the subsequent theoretical analysis which require clarification. 1) It is incorrectly stated that steady-state conditions are revealed by a slope of unity on a plot of log i vs log (time). This objection is trivial if the author meant to say a slope of zero, although it is unclear how subsequent extrapolation was made to determine the steady-state creep rates at low stresses for the zircaloy-2. If the plot used was actually log c vs log (time), it is unlikely that a slope of unity would represent a constant creep rate. A plot of log (c - co) vs log (time), where c0 is the extrapolated intercept sf the steady-state creep rate on the strain axis, would have a slope of unity during steady-state creep. However, eo cannot be determined unless is is already known. 2) The author chooses to interpret his results based on the equation: where A, and B, are structure-sensitive parameters, Ql and Q, are the activation energies for the particular creep process, and n describes the sensitivity of the creep rate on stress. The first term represents a slip creep process and the second a diffusion creep process. However, it is stated later that "two distinct processes acting in parallel are involved". Eq. [I] surely represents two processes in series since each reacts to the total applied stress and t, is the sum of the individual creep rates. If the processes are acting in parallel, then the effective stress in each would be less than the applied stress. The component stresses would be given by sl + s2 = a but it is not clear how the magnitude of either, or the corresponding stress exponent, could be determined.

Jan 1, 1969

By E. W. Edson, F. W. Hertal

In some fields the problem of mud fluid is simple and easy of solution. But in the Ventura Avenue field the acquisition and disposal of good drilling mud is not the least of the problems that confront the operator. In fact, mud fluid in the Ventura Avenue field is a very important factor in the drilling of the wells. It is quite probable that many of the factors affecting mud in this field will not be found in most of the fields with which the reader is familiar. However, in the fields where the mud fluid causes no apparent problem it is probable that some of the points brought out in this paper could be used to economic advantage. In fields where caving and squeezing formations and high gas pressures are present, as in the Ventura Avenue field, it is believed that application of methods outlined will be of great assistance in drilling wells. On account of the sandy nature of the formation and the lack of suitable shale bodies in the strata drilled through in the Ventura Avenue field, the wells make practically no mud during drilling. It is necessary therefore to supply drilling mud to the wells that will carry the drill cuttings to the surface, and also will " wall up" the drill hole and prevent the sandy formations from caving. Mixing and Handling Mud Fluid The clay used to make the mud fluid is obtained from a shale stratum in the upper Pico (Plioccne) formation found about a mile on either side of the field. Since high gas pressures and caving formations were first encountered in the Ventura Avenue field and mud fluid was needed to combat them, the mixing of this mud fluid has gone through a process of evolution. First, the clay was mined and hauled to the derrick, where it was shoveled into the well and left for the churning action of the bit to mix into a mud in the hole. The next move was the construction of a mixer to mix the clay to a mud fluid which was pumped into the well. These mixing

Jan 1, 1930

By Frederic A. Delano

In adding one more to the list of papers that have been presented on the subject of steel rails, I wish to explain at the beginning that in enumerating the steps in the manufacture which, I think, have an all-important effect on the wearing-qualities of the rail produced, I do so with no little hesitation. As a student in the field, I am anxious for the opinions of others, and have finally decided to ask for it in this way. I have not stated everything which I think affects, in one way or another, the life of rails, but have confined myself to those steps in the manufacture which I felt most sure did do so. Recognizing the danger of being carried away by enthusiasm, I have endeavored to make my assertions with caution, and to understate my case rather than to overstate it; but if I have succeeded in throwing a ray of light on this vexed question and placed it in the eyes of some railroad men in an aspect which they have not fully considered, my boldness will be more than justified. I. Uniformity in the quality of the material charged into the converter assists the attainment of uniformity in the steel produced.— This is the argument which is used by the champions of the cupolamelting or indirect process, and has considerable weight. It takes vastly more skill to make good steel if there is a great irregularity in the iron charged into the vessel than if there is not this irregularity ; but on the other hand, there are certain advantages in the direct method, such as a lower sulphur-percentage from the same furnace-iron, while it is possible to get as great uniformity in the iron charged by having the furnace-capacity enough in excess of the demands from the converting department, to allow for occasional " slips " in the furnaces, and permit the mixing of the iron from two furnaces which are respectively too " hot" and too "cold." 11. Care in pouring ingots at the proper temperature into warm moulds, and the treatment of ingots before rolling, have important effects on the rails made from them. In other words, many of the failures in rails and the uneven wear of rails are often traceable to

Jan 1, 1888

By Henry Hibbard

THE process of making washed metal now followed is in principle that described by Holley before this Institute in 1879, as the Krupp washing process. Sir Lowthian Bell also experimented extensively in England during 1877 and 1878 on refining iron and joined his interest with Krupp, the process being often referred to as the Bell-Krupp process. The only plant in this country now operating this process is that of the Brier Hill Steel Co., Youngstown, Ohio. This process may be considered as the sole survivor of the numerous methods conceived for refining crude iron, when the removal of phosphorus from steel-making material was the great desideratum affecting large districts. The east coast of England and all northern Germany, the homes of Bell and Krupp, respectively, could at that time make steel only from imported ores. These processes were in use or in various stages of development 40 years ago and all except the Bell-Krupp received their quietus from the development of the basic steel processes, both pneumatic and open hearth. The aim of the early refining processes was, first, the removal of the silicon; which could be clone on a sand bottom, and later, the removal of the phosphorus, requiring a bottom which would give or permit a basic slag. The incidental advantages of increased yield and small fuel consumption were not generally recognized or considered; the aim of the later. operations was the saving of the difference in value between low and high phosphorus irons, as well as hastening the removal of the metalloids. The chemistry of the washing process follows in part that of the puddling process, and indeed washing might, be considered as the first half of puddling, since all the non-ferrous elements of the crude iron, except the carbon, are eliminated and the iron is maintained molten until cast. In puddling, the iron loses its carbon as well, and because of that, its fusion point rises above the hearth temperature; it freezes into a pasty malleable form, and is worked at once by squeezer, hammer, or rolls.

Jan 12, 1915

By Walter Lawson

THE first plans were made in 1930 for the mining by open-pit methods of the low-grade disseminated ore body now known as the Morenci open pit. It was not until 1937, however, that final plans were completed and the decision reached to go ahead with the actual development. Many advances were made in open-pit mining equipment during that period of seven years, therefore the ways and means of attack actually used were very different from those originally contemplated. Diesel-operated bulldozers, big trucks, full-revolving electric shovels and electric churn drills constitute the major equipment finally purchased for this modern stripping operation. Neither the bulldozers nor the big trucks were considered in the early operating plans, for at that time bulldozers had not, been used in mining operations and the trucks as yet were undesigned. The full-revolving shovel and the churn drills were not new developments in open-pit equipment, but both had undergone remarkable manufacturing transition, emerging far more efficient and far more dependable than their predecessors. Even the ordinary drilling steel had been fundamentally changed. It was now threaded so that the dulled cutting bits could be detached and replaced, thus eliminating the costly transportation of long bars to the drill shop for resharpening. The decision to use trucks in the preliminary stripping operations was based on the desirability of this type of transportation to economi-cally prepare the pit for rail haulage, coupled with the success that the contractors had had with them on other big excavation jobs. There are at present no plans for the use of trucks beyond the preliminary work, inasmuch as rail haulage will give lower costs after roadbeds and benches are once established.

Jan 1, 1938

By Benny Langston, Frank M. Stephens

Although little information is available concerning small-scale equipment for dust collection in laboratories, it is possible to adapt standard equipment for laboratory use. Dust from laboratory processes may be collected by cyclone separators, filters, electrostatic separators, scrubbers, and settling chambers. IN recent years much attention has been given to recovery, treatment, and disposal of dusts discharged into the atmosphere from operations of industry. considerable data has been accumulated on both operation and design of dust-collector equipment for commercial installations. On the other hand, there is almost no published data on design and construction of small-scale equipment to handle dust problems that arise in the ore-dressing laboratory. Dust-collection equipment such as multiclones, single-cyclones, scrubbers, chemical and mechanical filters, settling chambers, and electrostatic separators has proved its efficiency for collecting dust in industry. In the laboratory, however, the engineer is faced with the problem of collecting small quantities of dust, inexpensively, without diverting the major effort from the metallurgical problem to the problem of collecting dust produced by the process. For most applications standard dust-collection equipment is too large for use in the laboratory; however, for control of dust in large working areas it is often possible to use a standard dust collector, such as an air filter, with branch ducts to eliminate a health hazard. For example, the well-furnished sample-preparation room containing small jaw crushers, rolls, and pulverizers, in addition to the riffles and screens necessary for preparation of samples, presents a perennial source of dust. The authors' experience has shown that a combination system consisting of overhead branch ducts to the individual equipment and floor ducts with grills, where applicable, connected to a central dust collector effectively removes dust generated in preparation of samples. Fig. 1 is a sketch of a downdraft dust-collector for table installation. Similar systems can be built with floor grids. For portable equipment such as laboratory vibrating screens this type of installation with a steel grill to support the heavy load is reasonably efficient. Overhead branch ducts to individual crushing and grinding equipment, although efficient, must be carefully controlled by dampers to prevent excess loss or a change in the composition of the sample. Change in sample composition can result from excess velocity, which causes selective removal of constituents of low specific gravity. Fig. 2' shows the theoretical effect of terminal velocity on spherical particles of different specific gravities in air and water under action of gravity. Fig. 3 shows the effect of air velocity on composition of CaCO, coal mixtures. Although the entrainment of dust particles in a moving air stream is the basic mechanism by which all dust-collection equipment functions, usually intake velocity of the dust-collection system must be controlled to prevent loss of part of the sample. As an example of what may happen when excess velocities are used, a mixture of 50 pct coal and 50 pct limestone was crushed to —10 mesh and fed to a pulverizer equipped with an overhead dust-collection system. Fig. 4 shows the overhead dust-collection equipment used in this test. The pulverizer was set to give a product 95 pct —100 mesh in two stages. Velocity of air passing over the lip of the pulverizer was measured with an anemometer. After grinding, the finished product was analyzed to show the amount of calcium carbonate present. Fig. 3 shows graphically the increase in calcium carbonate as velocity through the dust-collection duct was increased. These data show that at a velocity of 1 ft per sec little if any of the coal was entrained by the overhead draft. At the maximum velocity, about 6.5 ft per sec, approximately 7 pct more coal was entrained than calcium carbonate. From an operating standpoint, this problem can be remedied easily by dampering the line to control velocity. The lowest velocity commensurate with satisfactory dust control should be used to prevent excess loss and, in some cases, selective dust loss. Collection of Dust in Laboratory Processes As in industry, the engineer desires to collect efficiently the dust produced by processes being investigated on a laboratory scale. However, in the collection of laboratory dusts he is faced with two additional problems: 1—The volumes of gas and the quantity of dust that must be recovered are small when compared with the capacity of standard dust-collector equipment, which must be scaled down in design except for collection of dust from large pilot-plant operations. 2—In addition, because of the variety of problems studied in the process laboratory, the engineer cannot design today a dust collector that will meet the conditions imposed by the processes of tomorrow. Sometimes, therefore, he must compromise collection efficiency to minimize the cost of fabrication and the amount of time diverted from the metallurgical to the dust-control problem. For collection of dust from laboratory processes a cyclone separator, filters, electrostatic separators, scrubbers, and settling chambers can usually be adapted for small-scale operations. The following

Jan 1, 1955

By A. E. Dwight, A. F. Berndt

ThE published U-Ru equilibrium diagram indicates the existence of six intermetallic compounds in this system.' The structure of only two of the compounds, u2Ru2,3 and URU3,4 have been identified. This communication reports on the crystal structure and density of Uau3, which is formed by a peritectoid transformation at 1025° ± 5°C: U3Ru4 + U3Ru5 = U2Ru3. An alloy with the stoichiometric formula U2Ru3 was prepared by arc melting electrolytic uranium and ruthenium of 99.9 pct purity on a water-cooled copper hearth under an argon atmosphere. After homo-genization at 1000°C for 3 days, a metallographic examination revealed that the peritectoid transformation was complete and less than 5 pct of a second phase was present. A powdered sample, obtained by crushing the brittle compound, was annealed for 1 hr at 1000°C and air-cooled. Debye-Scherrer patterns were obtained with filtered CrKa, FeKa, CoKa, or CuKa radiation. The X-ray patterns of U2Ru3 weFe indexed as an fcc structure with a. = 12.895 0.00lA. The unit-cell constant and its standard deviation were calculated by a computer program described by Mueller, Heaton, and Miller.5 The density, measured by an immersion method, was 14.45 g cm-3. A calculated density of 14.48 g cm-3 was obtained on the assumption that twenty-four formula units (120 atoms) comprise a unit cell. The space group is either oh7 Fd3m, or the less symmetric, T4h, Fd3, since reflections indexed as hk0 with h + k + 4n are absent. All values of h2 + k2 + 12 permitted by both space groups are listed in Table I together with dc, do, and I. values. The calculated d spacings were obtained by the computer program of Mueller, Meyer, and simonsen.6 The observed d spacings above 0.77A were obtained from X-ray" patterns prepared with CuKa radiation, above 0.90A with CoKa radiaaion, above 0.98A with FeKa radiation, and above 1.16A with CrKa radiation. An attempt was made to identify the crystal structure of U2Ru3 by comparison with published data on other A2B3 compounds. A recent compilation7 of intermetallic compounds lists thirty-two structure types with the A2B3 stoichiometry. Only two of the structure types are fcc and they are Sb2O3(r), senarmontite, with 16 Sb2O3 per unit cell, and In2Te3 for which several structures have been proposed.8 However, the two cases cited do not have twenty-four formula units in the unit cell. We therefore, cannot identify UPRU3 with any of the other known A2B3 compounds. Ternary alloys were made in which 5 at. pct Os, Rh, or A1 were substituted for 5 pct of the Ru in U2Ru3. The osmium substitution increased the unit cell constant to 12.899 * .001A, which is to be expected since the atomic volume of osmium is slightly larger than

Jan 1, 1969

By E. W. Cawthorne, R. I. Jaffee, C. M. Craighead

SOLUTION of a solid metal or alloy in a molten metal bath is used daily in melting operations, extractive metallurgical processes, and in brazing. It is generally recognized that temperature, time, agitation, and the composition of the solute metal and the solvent bath all affect solution rate. However, there is little information available in the literature on the kinetics of the process or the relative effect that these variables have on solution rate. In connection with an aluminum brazing study, data on the solution of aluminum in an A1-Si* bath to promote rapid solidification. The chemical analyses were made on drillings taken from the cast plates. The results of this work are listed in Table I. The thermal-analysis data were obtained on 200 gram samples cooled at approximately 1.5" per min. A calibrated chromel-alumel couple was used. The thermal arrests were recorded autographically on a General Electric photoelectric potentiometer recorder. The instrument was calibrated to 22.5 pct. The thermal emf was bucked with a Leeds and Northrup semiprecision potentiometer so that 1 mv represented the full scale of the GE recorder. Referring to Table I, it will be noted that the analytical results tend to be lower than the intended compositions by about 0.3 pct Si in the higher ranges. In view of the known difficulties in obtaining accurate silicon determinations by wet analysis when the silicon content is high and in view of the care that was employed in weighing and preparing the alloys, the intended compositions are believed to be more accurate than the analyses. Furthermore, when the thermal-arrest data are plotted against the intended compositions, a smooth curve is obtained, as shown in Fig. 1. This is not the case when the data are plotted against the analytical results. It will be noted from Table I that the 12.5 pct Si alloy (melt 4) showed a primary arrest at 577.6"C and the eutectic at 576.l°C. The metallographic examination of this chill-cast plate sample showed a small amount of primary silicon. These results, Fig. 1, place the eutectic at slightly less than 12.5 pct Si and are in rather good agreement with the unpublished Hanford data. In all of the subsequent work, the composition of the A1-Si dipping baths was determined by thermal analysis (spread between the primary arrest and the eutectic temperature) employing 12.5 pct Si and 577.2 °C as the composition and temperature of the eutectic. Material Preparation and Selection of the Techniques: At the beginning of this work, it was anticipated that, owing to oxide film present on the surface of the aluminum, difficulty would be encountered in obtaining rapid uniform wetting of aluminum specimens dipped in the A1-Si bath. The following etchants were investigated as possible methods of providing a thin uniform oxide film on the specimen surface: 1—phosphoric acid (H³O4), 2—fluoboric acid (HBFI), 3—sodium hydroxide (NaOH), and 4—hydrofluoric acid (HF). Tests with sheet .specimens (2x½x0.06 in.) of 2s aluminum prepared with these etchants indicated that the fast uniform wetting required for this work could not be obtained if any oxide film existed on the specimen surface. Tests were then conducted by dipping similar specimens etched in 5 pct NaOH and given a thin

Jan 1, 1956

By H. L. B. Gould, Jr. Wenny D. H.

TO date there has been but limited interest in alloys of 80 to 95 pct Co and Fe with or without other additions. In 1932, S. R. Williams' reported practically zero magnetostriction for the 90 pct Co-10 pct Fe alloy. This same composition was used for pole pieces to control the magnetic field in magnetrons operating at high temperatures.' In 1947, a 90 pct Co, 9.5 pct Fe, and 0.5 pct Mn composition was investigated3 for use in ballast lamps because of its high temperature coefficient of resistance. Recently, as part of a survey of ductile and malleable magnetic alloys capable of being processed to thin gages for possible applications in memory devices, the high Co-Fe alloys have been re-examined to determine their fabricating and magnetic characteristics. Alloys from 80 up to 95 pct Co and Fe with and without additions such as vanadium were prepared. In general these all had excellent ductility and malleability. Wire was drawn to thin gages without difficulty and fine hard-drawn wires flattened to 2) The phenomenon may have potential in estimating the carbon content of molybdenum. A given solution-treating temperature and cooling rate could perhaps be calibrated so that the area fraction of surface covered by carbide could be interpreted in terms of carbon concentration. By segregating to the surface, a big "magnification" of the carbon content is obtained, which should make the method cheap, direct, and sensitive and, therefore, perhaps of interest to the molybdenum industry. This work was conducted at Battelle Memorial Institute. Financial support by the Aeronautical Systems Division, United States Air Force, under Contract No. AF 33(657)-7376, is gratefully acknowledged, and the writer is thankful for the experimental assistance of Miss Marjorie Cantin. ribbon without splitting. Similarly, strip was cold-rolled as much as 99.75 pct reduction to a 0.25 mil thickness without intermediate anneals. Samples of round and flat wire and foil, in the severely cold-worked and annealed states, were checked for magnetic characteristics. The alloys exhibited widely divergent magnetic characteristics depending on the processing and heat-treating procedures used in preparing the samples. Direct-current hysteresis loops showing the different magnetic characteristics of 90 pct Co, 9.5 pct Fe, and 0.5 pct Mn alloys are shown in Figs. 1 to 8 inclusive, while Figs. 9 and 10 show the loops for an alloy of 82 pct Co, 11.75 pct Fe, 5.6 pct V, and 0.65 pct Mn. Figs. 1 and 2 show the high remanence and exceedingly square-loop characteristics of the hard-drawn wire and ribbon roll flattened therefrom. With the change in processing from roll flattening to flattening by drawing through flat diamond dies the resultant change in texture is accompanied by the drastic change in the shape of the loop as shown in Fig. 3. This skewed loop on annealing reverts to a more normal loop as shown in Fig. 8. The most unique loops are obtained with flat rolled strip. These are shown in Figs. 4 and 5. In the case of the hard-rolled material, Fig. 4, there is little change in induction until the magnetizing force reaches 50 oe. From 50 to 60 oe there is a sharp increase in induction to over 15,000 gauss, which for all practical purposes is saturation. The induction remains at a constant value while the magnetizing force decreases to 40 oe. At this point the

Jan 1, 1965

By K. P. Gupta

In ternary systems containing silicon and transition elements, silicon was found to stabilize the a phase.1 At 1000°C a broad a-phase region was found in the Cr-Mn-Si system,1 which extends very close to the Mn-Si binary line (within about 3 at. pct Cr). Later investigation showed that, if chromium was replaced by small amounts (3 to 5 at. pct) of v,1 Ti, Nb, Ta, Mo, or w,1 the a phase or the R phase was again stabilized. Whether stabilization of complex crystal structures is possible by small additions of iron, cobalt, or nickel to Mn-Si is not known. Investigation of the Co-Mn-Si system4 shows the presence of several ternary phases, but at cobalt concentrations higher than 10 at. pct. In the present work the ternary systems Fe-Mn-Si and Co-Mn-Si were investigated at low iron and cobalt concentrations (< 7 at. pct Fe or Co) in search of phases of complex crystal structure. Experimental Procedure. The alloys were pre-pared by induction melting Co (99.8 pct), Si (99.9 pct), electrolytic Fe (99.88 pct), and Mn (99.9 pct) in recrystallized alumina crucibles under an inert atmosphere of argon gas. The alloy specimens were wrapped in molybdenum foil, sealed in argon-filled (at 1/2 atm) silica capsules and annealed for 72 hr at 1000" 1°C, and water-quenched. The use of argon-filled capsules was found to reduce the losses during annealing and the molybdenum foil prevented reaction of the manganese with silica. The total weight loss due to annealing and melting was found to be less than 1 pct for each alloy. The alloys were not analyzed chemically. A part of each annealed specimen was polished and examined metal-lographically using etching solutions, a) 0.1 to 0.5 pct oxalic acid solution in water, or b) 0.5 pct HNOs in methyl alcohol. Even though the etching solutions were quite dilute, the specimens were heavily etched and stained if the etching time exceeded more than 5 sec. Etching times found suitable were usually 1 to 3 sec. For X-ray diffraction work, a part of each annealed specimen was powdered by crushing after the exposed surface was ground off. X-ray diffraction patterns were taken with powder specimens using a 20-cm-diam asymmetrical focusing camera and Fe K radiation. These powder patterns were found quite satisfactory for the purpose of phase identification. However, X-ray diffraction patterns of single-phase alloy powder specimens were also taken using a Siemens diffractometer and filtered Cr-Ka radiation for greater resolution of the diffraction lines. Results and Discussion. In the Fe-Mn-Si system a new ternary phase was found at 1000°C between the p manganese and the MnsSi phase regions. The approximate phase relationships in this region of the 1000°C isothermal section are shown in Fig. 1. The new ternary phase, designated as the K phase, was found to occupy a narrow region about 1 at. pct in width and extending from Fee.oMn74.5Silg.5 to Fe.Mn.Silg.. At the high-iron content region, the K phase was found in equilibrium with the p manganese and the MnsSi phases but, at the low-iron content end of the K-phase region, the phases in equilibrium with the K phase were the p manganese phase, the MnsSi phase, and another new phase, designated in Fig. 1 as the v phase. The v

Jan 1, 1964

By F. G. Stone

A strain anneal process has been developed for the production of iron tensile test specimens, the gauge length consisting substantially of a single crystal. Since the method has been quite successful and the results of general interest, the process will be described in detail. The essential feature of the method is the continuous, slow increase of furnace temperature during the grain growth annealing treatment. Briefly, the procedure is as follows: I. Heat machined bars to 950°C in vacuum, hold I hr, furnace cool. 2. Strain to 3.5-3.8 pct elongation (axial loading). 3. Anneal, continuously raising furnace temperature from 450 to goo°C at a rate of so0 per day. 4. Hold at 900°C for 100 hr, furnace cool. Tensile test bars with a 1/4- X I-in. gauge section have been machined from 35 in. Armco iron plate and from 3/8 in. rounds of Puron, a high purity laboratory iron. The axes of the test bars were parallel to the rolling direction. During the machining operation the bars were polished in the lathe with No. 600 emery paper, and this polished surface proved satisfactory for subsequent macrographic examination. A micrographic examination of the materials showed that both were high in FeO inclusions, those of the Puron being smaller but much more numerous. An initial vacuum anneal of I hr at 950°C followed by furnace cooling resulted in a ferritic grain size of ASTM No. 3 for Armco and No. I for Puron. Special heat treatments which reversed these initial grain sizes produced no marked improvement in single crystal production after subsequent treatments. The strain for subsequent grain growth was determined by measuring the decrease in diameter of the tensile bar during elongation. The change in diameter could be measured with a micrometer to +0.0001 in., corresponding to an accuracy of 0.08 pct for the elongation. The accuracy of the diameter measurement is also dependent on grain size because of surface roughening during elongation, and for this reason, a No. 3 grain size is preferable. Optimum grain growth was obtained for strains between 3.5 and 3.8 pct elongation. Once this critical range had been cstablished, all tests were held within it, and thus only meager data were obtained on grain growth following strains outside this range. In general, grain size decreased with increasing strain to about 5.5 pct elongation. Grain growth was occasionally ohserved with less than 3.5 pct elongation although this may have been the result of error in measurement. The program control device for the grain growth anneal consisted of a I rpm motor and worm gear drive, operating the dial shaft of a pyrometer controller through a pulley. Dial speeds of 33 and 50°C per day were tried, but the results at the slower speed were not sufficiently better to warrant the increased furnace time. The furnace tube was evacuated at intervals during the run and kept sealed the remainder of the time. When the controller reached 900°C, it was stopped and the temperature held for 100 hr. This eliminated most of the numerous minute crystallites of about 0.5 mm dimension usually visible on the etched surface of the single crystal. Since recrystallization occurs at the A3 point, the top temperature of 900°C provided a 10"

Jan 1, 1949

By J. B. Austin, R. L. Rickett

Measurements of the rate of decomposition of austenite at constant temperature are commonly represented by plotting the percentage transformed on linear coordinates against time on either a linear or a logarithmic scale, a method that yields a curve that in shape resembles an integral sign (Fig. 1). A graph of this kind is not always convenient because extrapolation to the beginning or end of the transformation, or even intebrpolation, may be uncertain unless there are a large number of observations, which seldom happens; furthermore, the degree of consistency of a set of measurements is difficult to judge from such a curve. It is desirable therefore to find some mode of plotting, or even better to find a standard variety of graph paper, that gives a straight line instead of the integral shape. The straight line has many advantages; the number of readings required to fix the position of the curve is greatly reduced, interpolatiorr is easy and rapid, extrapolation can be carried out with greater confidence and, finally, the consistency of the measurements is readily estimated from the scatter of the points. The last advantage is particularly valuable when the data are obtained by direct microscopic examination alone, because they are influenced by the skill of the observer in estimating the relative size of areas, possibly also by undetected inhomogeneity of the specimen. A search for ways of representing the observations as a straight line yielded two methods which are described in this paper. The paper also includes an account of some interesting relations brought to light in applying these methods to the available experimental data. Usually the best way to derive such a method of plotting is to base it on established principles of chemistry and physics, as has been done, for example, for the temperature variation of the equilibrium constant of a chemical reaction. But so little is known of the mechanism of the decomposition of austenite, and so little is available in the way of well established background for changes of this kind, that it is simpler to rely upon purely empirical means. The general plan therefore is to study existing data with a view to finding some function of the direct observations that will

Jan 1, 1939

By Robert W. Pack

Sooner or later in the development of any natural resource it becomes highly desirable to know the quantity of this resource in the country as a whole, as well as of the part that is being developed, for the general course and conduct of the development work must be governed, to some extent, by the total supply available. An accurate estimate of the quantity of any natural resource is difficult to make; yet if one is diligent enough one can obtain a pretty accurate idea of the quantity of marketable timber, the acreage of tillable land, or the horsepower that may be developed from the streams, for these are things that may be measured. But any attempt to estimate the quantity of some mineral in the ground appears to enter the realm of imagination and it seems that the estimate can be nothing more than a blind guess. It may appear to be especially futile to attempt to determine the quantity of oil and gas that is available in the ground, for these minerals are so vagrant that even if the quantity now available should be known quite exactly, the quantity that will eventually be obtained may be much less, for certain losses in the extraction of both oil and gas are unavoidable, and just what these losses will be cannot be predicted. Though necessarily inaccurate, estimates of such mineral reserves are, however, of distinct value, for they summarize the existing knowledge of the deposits of the mineral and thus enable those who are interested in some industry that depends in one way or another on this mineral to formulate a rational commercial policy. Some time ago, when the price of gasoline suddenly rose in a rather spectacular manner, the writer was one of the U. S. Geological Survey geologists called upon to help to estimate the quantity of oil that could be obtained in the United States, for the fear had become widespread that perhaps the rate of increase in the price of gasoline was a measure of the rate of depletion of the supply of petroleum. It thus became his

Jan 1, 1918

By E. E. McGinley, L. D. Woodworth

DURING the past several years has occurred what, in the light of future events, may aptly be called the rebirth of the acid Bessemer process. The increased attention given to the technical and metallurgical details involved in the production of Bessemer steels has been exceedingly fruitful, and indicates the value of further research and plant development. In times like these, when the steelmaking capacity of the country is operating at a maximum rate to supply materials for the national defense program, it behooves the Bessemer operator not only to strive to increase production but also to maintain a high standard of quality. The opportunity is ripe, it seems, to recapture fields of application once considered the birthright of Bessemer steels, but supplanted in recent years by open-hearth grades. This involves cooperation all along the line, from the blast-furnace operator to the metallurgical contact man and salesman. The metallurgist&apos;s part in this program involves the study of the many steelmaking variables and the measures necessary to ensure constancy in the finished product. It is equally important that the knowledge gained be disseminated widely to ensure the wise application of Bessemer steels in new fields. The merits of Bessemer steels for certain work are well understood. The combined properties of good weldability, machinability and stiffness are unique and fully explain the strong entrenchment of Bessemer steels in certain fields; e.g., skelp for small butt-weld conduit, screw steels machined in automatics, and certain tinplate applications. It is the purpose of this paper to review briefly the physical properties of Bessemer steels as contrasted with those of open-hearth steels, to discuss control measures now employed in the making of Bessemer steel, and to consider the advantages derived from the use of these control measures. PHYSICAL PROPERTIES OF BESSEMER VS. OPEN-HEARTH STEELS A number of Bessemer blows and open-hearth heats were tested for tensile strength, ductility and impact strength. The steels selected were confined to sections from ¾ to 1 ¼ -in. diameter, inclusive, and the carbon content covered was sufficient to yield parallel ranges in ultimate strength for the comparison. Other factors, such as the extent of deoxidation of the steel and variations in chemistry, were kept as comparable as possible. Machined test pieces of 0.505-in. diameter with an 8-in. gauge length were pulled. The data obtained are shown in Fig. 1, ultimate strength being plotted against carbon content. This graph shows that for equivalent carbon content Bessemer steel has on the average 15,000 lb. per sq. in. greater tensile strength and, conversely, for the same tensile strength Bessemer steel requires on the average 0.14 per cent less carbon. The average phosphorus content for the Bessemer steel was 0.090 per cent,

Jan 1, 1941

By J. B. Austin, R. L. Rickett

Measurements of the rate of decomposition of austenite at constant temperature are commonly represented by plotting the percentage transformed on linear coordinates against time on either a linear or a logarithmic scale, a method that yields a curve that in shape resembles an integral sign (Fig. 1). A graph of this kind is not always convenient because extrapolation to the beginning or end of the transformation, or even intebrpolation, may be uncertain unless there are a large number of observations, which seldom happens; furthermore, the degree of consistency of a set of measurements is difficult to judge from such a curve. It is desirable therefore to find some mode of plotting, or even better to find a standard variety of graph paper, that gives a straight line instead of the integral shape. The straight line has many advantages; the number of readings required to fix the position of the curve is greatly reduced, interpolatiorr is easy and rapid, extrapolation can be carried out with greater confidence and, finally, the consistency of the measurements is readily estimated from the scatter of the points. The last advantage is particularly valuable when the data are obtained by direct microscopic examination alone, because they are influenced by the skill of the observer in estimating the relative size of areas, possibly also by undetected inhomogeneity of the specimen. A search for ways of representing the observations as a straight line yielded two methods which are described in this paper. The paper also includes an account of some interesting relations brought to light in applying these methods to the available experimental data. Usually the best way to derive such a method of plotting is to base it on established principles of chemistry and physics, as has been done, for example, for the temperature variation of the equilibrium constant of a chemical reaction. But so little is known of the mechanism of the decomposition of austenite, and so little is available in the way of well established background for changes of this kind, that it is simpler to rely upon purely empirical means. The general plan therefore is to study existing data with a view to finding some function of the direct observations that will

Jan 1, 1939