Search Documents

By J. P. Sheeha, W. F. Craig, M. Baeyertz

The loss in toughness caused by phosphorus within commercial ranges was studied in AISI-SAE 1340 steel and in molybdenum modifications of this grade. The replacement of part of the manganese by molybdenum in amounts which maintain the hardenability of the standard 1340 grade was shown to counteract to a marked degree the detrimental effects of phosphorus. THIS paper deals with the effect of phosphorus on the toughness of 1340 steel and with the effect on toughness of replacing part of the manganese by molybdenum while retaining the same hardenability as that of 1340. In previous work1 a progressive decrease in toughness was observed when the phosphorus content of 5140 was raised from 0.020 to 0.036 pct; that is, from a moderate phosphorus level to one higher but yet within the AISI-SAE specification for this grade. The structural condition of the steel was tempered martensite. Toughness was evaluated by the transition temperature determined by V-notch Charpy tests. Replacement of a part of the chromium in 5140 by molybdenum provided a factor of safety against loss of toughness caused by phosphorus, especially where the steel was cooled slowly after tempering. Scope of the Study: In view of the improved tolerance for phosphorus obtained by replacing a part of the chromium in 5140 with molybdenum, it seemed desirable to investigate the possibility of obtaining similar improvement in 1340 by replacing part of the manganese with molybdenum. Heats were made at different phosphorus levels, in a series that began with 1340 and ended with steels containing 0.32 to 0.35 pct Mo with 0.82 and 0.90 pct Mn. The analyses of the heats are given in table I. In order to facilitate later discussion, the 1340 heats have been placed together in the order of increasing phosphorus content, and the molybdenum modifications have been grouped according to phosphorus

Jan 1, 1951

By Charles T. Holland

This discussion is concerned with those comparatively infrequent bumps that eject material from the failed mass with enough energy to wreck heavy machinery and seriously injure or kill people. In such cases there is a loud report, and the pressure waves set up in the mine atmosphere wreck ventilation controls several hundred feet from the site of the failure. Vibrations are induced in the earth's crust which may be detected several miles from the point of origin, and explosive gases may be released in large quantities.* Usually a dense suspension of dust is produced from the failed mass, together with dust placed in suspension by the resulting air blast. These rock bursts or bumps have also been called mountain shots, bounces, pillar bursts, and crumps. Such occurrences, when extensive, are serious catastrophes, and may force abandonment of the mine.1

Jan 9, 1958

By J. P. Lesley

The old do not love to see the young pass away from the light of the sun before them. Fathers would fain keep their sons by their side to the. end of life ; but the old Greeks, who loved the old gods, were wont to moderate their grief with the sweet superstition that only those whom their gods especially loved died early. The Christian church found consolation in that superstition applied in a new form to its new sorrows, and paid its most enthusiastic devotion to the memories of its young and beautiful martyrs. The natural science of our century is robbing us fast of this and all other superstitions, sweet as well as bitter, and leaving us for consolation to the teaching—colder, yet kinder—of personal fortitude and that optimism Which intelligently translates the Cosmos of Humboldt back into its old name of the Harmonia of Pythagoras. The Homeric Kataclothes, the three fates, are dead and gone for us, with that old world which comprehended none of the laws of cause and effect, and sorrowed for those who were cut off from the land of the living without hope of more than a shadowy existence beyond the river of death. All the more the ancients cherished the memory of their dead and lavished their choicest art upon their monuments. We moderns have lost the monumental arts, but we better keep the monuments which our dead leave behind them. No one of us who has done good work can fail to be remembered; and in an Institute like this, which keeps the press at work, an immortality in the memory of men is more possible, more certain, for every one of its members than the greatest heroes of antiquity could anticipate for themselves. In old apocalyptic times the works of men followed them through death to the throne of God to be their advocates in judgment, but in these modern times our works remain this side the grave, to follow the name of the departed one as it takes its course along the history of his peculiar art or science advancing slowly to perfection. We write the epitaph, not upon the mouldering stone of a tomb, but on the pages

Jan 1, 1890

By Harold Rose

THE peak of production from the Appalachian natural gas field was apparently reached about 10 years ago, and the annual production from Pennsylvania, West Virginia and Ohio has now dropped to about two-thirds of the amounts obtained in 1916 and 1917. This .falling off in production has occurred in spite of vigorous efforts and large expenditures by producing companies to maintain or increase their output. The greatly increased costs of development and handling are reflected in the present average value of natural gas at the point of consumption, which value in the three states referred to, has more than doubled in the past 10 years. While it is true that the natural gas production of the United States has increased during recent years, this increase has come from southwestern states, particularly from Oklahoma, California, Louisiana and Texas, which states are now leaders in the production of this valuable but fleeting resource. Pennsylvania, originally the leading state in natural gas production, occupies sixth place in the latest (1924) U. S. Bureau of Mines statistics. West Virginia, which held first place for 15 years, has dropped to third rank, and Ohio is the seventh state in the order of natural gas production. Domestic and industrial demands for gas are constantly increasing everywhere in the United States. These growing demands have accentuated the difficulties in the localities with depleted natural gas supplies, and serious shortages have already occurred during winter months in the Pittsburgh district. Some relief has been obtained by placing restrictions on the industrial use of natural gas, and by increasing the price (which tends to reduce consumption). Yet these are but temporary expedients for checking gas consumption, which fail to solve the problem of adequate future supplies of gas.

Jan 10, 1926

By Homer Staley

THE casting alloy 88 copper, 10 tin, 2 zinc, commonly known in England as Admiralty metal and in this country as Government bronze, gun metal, or Naval Department composition G, has, at its best, many valuable properties. However, its physical properties are known to vary widely with slight changes in method of manufacture of the castings, such as slight variations in composition, variation in pouring temperature, kind of mold used, method of pouring and gating of molds, size and shape of castings, amount and kind of heat treatment., and so forth.1 The microstructure of castings made from this alloy is influenced by slight variations of composition, rate of cooling, and kind and length of heat treatment. This is best understood by reference to the equilibrium diagram. The part of the diagram in which we are interested and the effect of the thermal equilibrium relations on the physical properties of the alloy 88 copper, 10 tin, 2 zinc, have been discussed by Hoyt, Camp-bell, Primrose, and Rawdon.2 In Fig. 1 is given the equilibrium diagram of the copper-tin alloys. Briefly stated, the relations of composition and temperature changes are as follows. Compositions between A and a consist of but one constituent-the a bronze, which is a, solid solution of copper and tin, rich in copper. On cooling from the molten state these compositions gradually crystallize, at temperatures above 790°, into a mass of interwoven tree-like crystals or dendrites. The cores of the dendrites are rich in copper and the percentage of tin gradually increases as the surfaces are approached. As cooling progresses, after all the metal has crystallized, no further changes occur, in the crystals other than diffusion within the crys-

Jan 9, 1919

By C. R. Fast, George C. Howard

Laboratory and field testing of various squeeze cementing techniques and materials revealed that many improvements could be made in squeeze cementing operations. The use of a slow-pumping squeeze cementing procedure permitted the control of the quantity of cement displaced into a formation and aided in obtaining a high final squeeze pressure. Field testing indicated the desirability of obtaining high final squeeze pressures, the need for improved formation breakdown fluids, and the necessity of controlling the pressure differential during testing after a squeeze job. INTRODUCTION During the past few years, squeeze cementing operations have been investigated, both from the theoretical as well as the practical point of view, in an effort to arrive at some solution to the many and varied problems that arise with this type of operation. A review of well files indicated that in many instances, wells were being squeeze cemented four and five times before a satisfactory pressure buildup was obtained. There seemed to be considerable variation in opinion as to the proper method of squeeze cementing, as well as disagreement as to the proper breakdown agent, the quantity of cement that should be used, type retainer and length of WOC* time that was necessary. Consequently, it was deemed advisable to approach this problem theoretically, field testing each idea developed in hopes of eventually arriving at a squeeze cementing procedure that would give reasonable assurance of a successful job after one squeeze cementing operation. This investigation was. therefore, divided into two broad headings: (1) Preliminary studies, which include both theoretical and laboratory studies, and (2) Field investigations to determine the proper squeeze cementing methods. PRELIMINARY STUDIES Overburden Pressure Studies Squeeze cementing problems are so intimately related to the earth's overburden pressure that solutions to them are very difficult, if not impossible, without an understanding of the nature and magnitude of the overburden pressures encountered at the depths of producing wells. It was thus felt that the first approach to research on squeeze cementing should be made through a study of these pressures. Since there has been rather loose usage of a number of the terms related to overburden preasure by different writers, the terms to be subsequently used are defined here. Theoretical overburden pressure is the calculated pressure at any given depth exerted by the theoretical weight of overlying formations as calculated from the average rock density. Fluid displacement pressure is that pressure at which fluid can be injected into a formation after it has been broken down. It may be more or less than the theoretical overburden pressure. Formation breakdown pressure is that pressure at which a formation parts or breaks and is usually thought of as fluid displacement pressure plus rock strength. Breakdown agent is that fluid with which the formation is fractured. The first step in the study of the earth's overburden pressures involved a review of pertinent technical literature. The general opinion expressed was that the overburden pressure gradient of the earth's formations is roughly 1.0 psi per foot of depth, and that application of sufficient pressure to stratified formations. will cause them to part at or parallel to the bedding planes. The second step in the study of overburden pressures involved a study of available well data in an effort to obtain some definite information as to the actual values experienced in the field for the above mentioned terms. Data from 115 cement squeeze jobs in the Gulf Coast area and 46 cement squeeze jobs and acid jobs in the West Texas-New Mexico area were closely analyzed. The analysis of these data showed that the average formation breakdown

Jan 1, 1950

By S. F. Bartram, G. A. Chase

COMPUTED X-ray diffraction powder patterns of YNi3, YNi5, and CbBe3 are available on request from either author.

Jan 1, 1968

By J. H. Wernick, S. Geller

A number of new AB, compounds, in which A is a rare earth or yttrium atom and B is Al, Mn, Fe, Co, or Ni, having the cubic MgCu, structure (Laves phase) are reported. In most of the compounds, the interatomic distances are normal; the lanthanide contraction is observed. However, in the compounds CeB2, B = Fe, Co, Ni, Ce appears to have a valence substantially greater than three; in CeAl2, Ce appears to be trivalent. These results are interpreted as vesulting from an energetically more favorable situation for the 4f electron of Ce to be lost to the 3d band of Fe, Co, nnd Ni. Evidence for the existence of homogeneitj! ranges in these compounds is presented. THE purpose of this paper is to report on the crys-tallographic investigations of a large number of new compounds, Table I, with the MgCuz structure (cubic Laves phase). It is a part of a continuing study of the magnetic properties and structures of binary systems involving the rare earths. In a previous paper' some of the magnetic properties of such systems were reported briefly. We have also reported2 a number of compounds of the CusCa type. The compounds were prepared by induction melting in Argon atmosphere of mixtures of stoichiomet-ric amounts of the constituent elements.* For most of the compounds fused alumina or silica crucibles were used as the containing vessel; graphite crucibles were used to prepare CeA12, NdAl2 and TbA12. X-ray powder photographs were taken with CrKa radiation and the use of Straumanis-type Norelco cameras of 114.6 mm diam. The compounds AB2 belong to space group Fd3m-Ol with 8A in a): (000; 01/2 '/2;3) + 000-; b % XA and 16B in dl: (000; oVa %; 3) + 5/87; % %; 7e % Vs\£>. Because the intensities of the reflections on the powder photographs of the different compounds are similar, relative intensities were computed only for DyMnz for CrKa radiation, Table 11. In the calculation of intensities, the Thomas and umeda3 atomic scattering factors, corrected for dispersion,4 were used. The agreement between observed and calculated intensities leaves little doubt that DyMnz has the MgCuz structure. Crystallographic data for the ABz compounds are given in Table JII. Twelve of these compounds have been reported by other authors. A comparison of the published results with our work is given in Table W.* ers of elements of lower purity, to peritectic reactions in some cases, and to the presence of homogeneity ranges in these alloys, so that melting losses would still result in single phase alloys. The possibility of existence of homogeneity ranges in these compounds was investigated systematically only for GdMnz. At room temperature, the solid solution range is between

Jan 1, 1961

By E. T. Turkdogan

In this theoretical paper, a transport-reaction mechanism is suggested for the enhancement of the rate of vaporization of metals, or other materials, brought about by the process of convection and condensation. Based on theoretical reasoning it is predicted that, when there is a temperature gradient surrounding the heated object, a slight increase in the rate of vaporization brought about by natural convection is enhanced further as a result of condensation of the vapor close to the surface of the object. In order to derive the effective vapor-concentration profile, consideration is given to the super saturation of the vapor necessary for the homogeneous nucleation of the condensed phase from the vapor. For the formulation of the rate equation based on this mechanism, adequate information should be available on the transport properties of gases and vapors at elevated temperatures and the method of calculating nucleation pressures of the vapor. The methods of deriving such data are discussed in the paper and a rate equation is calculated for the vaporization of iron in helium for various temperature gradients in the boundary layer. Considerations are also given to the effect of oxygen on rates of vaporization of metals under isother ma1 and nonisotherma1 conditions. THE study of the methods of enhancement or retardation of basically transport-controlled vaporization reactions is of theoretical interest with possible practical implications. There are several ways of bringing about such effects. For example, Turk-dogan, Grieveson, and Darken1 demonstrated that the rates of vaporization of metals under isothermal conditions were increased by several orders of magnitude, up to the maximum rate attainable in vacuo, by introducing some reacting gas into the inert atmosphere surrounding the metal. Such an effect is brought about by the interaction of the counter-diffusing reacting gas and metal vapor in close proximity of the metal-gas interface. Another case which is often experienced in practice is that of vaporization affected by natural convection. Although several theoretical and experimental studies of this problem have already been made, no detailed consideration has been given to the possible effects of condensation of the vapor in the boundary layer on vaporization rates, which constitutes the subject matter of this paper. BASIC CONCEPT OF ENHANCED DIFFUSION-LIMITED VAPORIZATION When a heated object, for example a metal sphere, is submerged in a fluid medium, heat is transferred from the surface of the object to its surroundings by four simultaneously occurring transfer processes: i) free-molecular conduction at the gas-solid interface over the distance equal to the mean free path of the gas, ii) conduction and convection through the fluid-dynamic boundary layer, iii) latent heat of mass transferred, and it!) radiation. The free-molecular conduction becomes pronounced only when the total pressure in the system is very low, e.g., below 1 mm Hg. Therefore, this term may be neglected for ordinary pressures. At low mass-transfer rates, due to vaporization of the object, the contribution of process iii) to the heat transfer can also be neglected. Finally, since the temperature profile is not affected by radiation, the latter need not be considered. The natural convection is brought about by gravitational body forces arising from a decrease in the

Jan 1, 1964

By Raymond S. Weimer

OF the several characteristics of a coal that influence its suitability for use in a given piece of burning equipment, the clinkering and slagging characteristics of the ash of the coal are highly important. They determine the maximum rate at which the coal may be burned on a stoker or in pulverized form without difficulty from damage to metal parts, from erosion of refractory walls, or from stoppage of gas passages by accumulation on the tubes. They also determine the minimum rate at which a slag-tap furnace may be operated without difficulty in removal of the ash in fluid form. NEED FOR A BETTER CRITERION In common with other producers and users of coal, the Northern Illinois Coal Corporation has long used the available methods for the measurement of the clinkering characteristics of coal ash, chemical composition and fusion temperature of the ash, as criteria for the selection of coal that would suit the particular requirements of its customers. These two available criteria have greatly helped in the problem of selection but it is unnecessary to dwell upon the fact that they are not completely adequate for the purpose. The composition of the ash and its clinkering tendency vary widely over the company's mining area. In a certain period, some years ago, an unusual amount of severe clinkering of the ash of coal shipped made extremely acute the need for a better criterion of the clinkering that might be expected. It was also desirable that the criterion result from a reasonably rapid method, so that the clinkering characteristics of the coal would be known before shipment. Complaints on the severe clinkering of the ash came from only a fraction of the output of the mine but the occurrence of the clinkering seemed quite unpredictable. Attempts to relate the chemical composition of the ash and the fusion temperatures to the clinkering were unsuccessful. Coal from the area of the mine in which the fusion temperature of the ash was the lowest gave the least trouble from clinkering. Chemical analysis of the ash from that section giving the most trouble showed high contents of iron and low contents of silica, but frequently these were not greatly different from those of coals that gave little trouble from clinker. Aside from the clinkering difficulty, the coal was quite satisfactory. The ash content was normal and high rates of burning could be obtained, but again and again such severe clinkering would occur that the furnace would be shut down because of the accumulation of clinker. Examination of the clinker from the customers' plants showed that the clinkers that adhered to the grates and fouled the fuel beds were hard, flat, dense, and usually dark in color. Coal that was satisfactory gave clinkers that were softer, bulky rather than flat, of low density, and usually lighter in color.

Jan 1, 1944

By Donald L. Katz, Michael J. Rzasa

With greater effort being devoted to the discovery of new oil and gas reserves and a consequent increase in bottom hole pressures due to greater drilling depths, the phase relationships of hydrocarbon fluids at pressures above 10,000 lb psi are becoming increasingly important. The present paper discusses the results of research with a windowed cell on a methane-Kensol 16 system to pressures of 25,000 Ib psi and temperatures to 260°F. Kensol 16 is a commercial high narrow-boiling-range oil. It is shown that for the temperature range of 60 °F to 260 °F, this particular system exists in two phases to pressures of approximately 14,000 lb psi, and data are presented giving the relative amounts of liquid and vapor phase? coexisting under these conditions. Partial phase diagrams are shown for six different mixtures of methane and Kensol 16, three of which include the critical region. In contrast to mixtures composed of substances of fairly close volatility. critical opalescence was noted for as much as 200°F of the critical temperature. The critical locus of the methane-Kensol 16 system was estimated and the conventional pressure-composition and temperature-composition diagrams were prepared. From these, the equilibrium vaporization factors for methane and Kensol 16 were estimated for temperatures from 60 °F to 700 °F and to pressures above 12,000 lb psi. The relations of this study to petroleum production problems and other phase equilibria research are discussed. INTRODUCTION A knowledge of the physical behavior of naturally-occurring hydrocarbon mixtures is fundamental to a thorough treatment of nearly all operations involved in the recovery, refining, and transportation of petroleum. The operations may involve the applications of phase relationships, and the relative

Jan 1, 1950

By F. E. Poulson

The discovery of two new fields, Van, in East Texas, and Darst Creek, in the Balcones fault zone, is the outstanding development in 1929. The first six months was one of the most inactive periods in the history of East Texas. Five of the interior salt domes, which had been so eagerly sought as a result of the Humble Oil & Refining Co.'s strike on the Boggy Creek dome in 1927, were drilled with discouraging results, and the Boggy Creek field itself had fallen far short of expectations. Kelsey, a structure of considerable magnitude and extent in Upshur County, was equally disappointing; the Amerada Petroleum Corpn.'s initial test on this structure was dry. The situation improved in the latter half of the year. On Oct. 13, 1929, the Pure Oil Co. discovered the Van field. This gained for East Texas a permanent place in point of future potential production. There was a similar reaction in the Balcones fault zone. The Salt Flats (Bruner) field, the important discovery of 1928, proved its rating as a second Luling, but on account of repeated failures to extend the productive zone, wildcatting during the first half of 1929 in the Luling district was dilatory. In July, however, Darst Creek, a third fault-line field of majori mportance producing from Edwards limestone (Lower Cretaceous), was discovered. Retarded as development in this field has been by various attempts at proration, interest in the Balcones fault zone fields centered on Darst Creek as the year 1929 drew to a close. Development in East Texas Fields Discovered during 1929 Van.—The discovery well, Jarman No. 1 of the Pure Oil Co., is near the town of Van in the southeastern part of Van Zandt County, Texas. It is 55 miles northeast of the Powell field in Navarro County and 45 miles west of north from the Boggy Creek field in Cherokee and Anderson counties. Early in 1927, the Van area was submitted to seismographic exploration and outlined as a large anticline, the apex of which seemed to be

Jan 1, 1930

By H. F. Moore

This paper gives a preliminary summary of results of tests on the resistance to fatigue under reversed stresses of steel subjected to cold-working and of tests to determine the effect of rest on the endurance of steel under reversed stresses. The tests of cold-worked steel were undertaken as part of an investigation by the National Research Council Committee on Fatigue Phenomena of Metals and were made by Mr. Moore; the tests to determine the effect of rest are part of an investigation now being made by Mr. Putnam. Both series of tests were made in the Materials Testing Laboratory of the University of Illinois. The preliminary results of these tests are reported now. because it is believed that test data on fatigue strength should be available at the earliest possible moment; however, it should be clearly kept in mind that this paper gives preliminary results and is intended to encourage discussion rather than to give final conclusions. Before giving the data of the tests, the writers will explain the term "fatigue strength" as used in this paper and will discuss briefly the method used in interpreting the test data of repeated-stress tests. The term fatigue strength, as applied to a material, may be defined as that maximum fiber stress that will cause fracture of the material after the repetition of any given number of cycles of stress, each cycle involving the variation of stress from a minimum to the above maximum. The fatigue strength, then, varies with the number of repetitions occurring in the lifetime of a structural or machine member and with the range of stress for each cycle of stress. The fatigue strength will be lower for a member in which the stress is completely reversed than for one in which the stress varies from zero to a maximum. In interpreting test data from fatigue tests under reversed stress, the stresses and corresponding numbers of repetitions required for failure are plotted on logarithmic cross-section paper. In 1910, Professor

Jan 2, 1919

WE must begin by defining what we mean by the Copperbelt. This term is generally used to denote that region of Northern Rhodesia in which the copper mines of that territory are situated. The first published use of the term Copperbelt we have been able to trace dates back to 1905. The African World of December of that year contained an article entitled "The Great Northern Copper Belts of Rhodesia." The next reference we have traced is in 1909 in an article in the Transactions of the Geo- logical Society of South Africa. It began to be used generally in the late twenties and by 1929 was in common use to denote the region which today contains the existing large copper mines of Northern Rhodesia. The first of three accompanying maps is a very simple outline map of Africa showing where Rhodesia is within Africa, and where the Copperbelt is within Rhodesia. The second is a larger scale map of the Copperbelt itself. It will be seen that within the present Copperbelt there are six producing mines. Two of these are new and four are relatively established, having started operations between the two world wars. The Copperbelt also includes a town- ship called Ndola, which is not a mining town, but a railhead on the main line. This town has developed primarily as a result of the mining industry in the neighborhood. It describes itself as the Gateway to the Copperbelt and is shortly to become a refining center.

Jan 5, 1957

By A. S. Rhea

SALT-WATER disposal in the East Texas field by means of injection into the Woodbine sand is a relatively new procedure. The purpose of this paper is to present what has been accomplished to date in this field, with-out detailed discussion of other means of disposal, such as surface impound-ing for evaporation or release into surface streams. Subsurface disposal of salt water is still in an experimental stage in the East Texas field, and, though water can be injected into the Woodbine sand, the economic problem is not as yet solved. As past experience has been that fields producing from the Woodbine formation produce large quantities of salt water, it was assumed early in development of East Texas that it would be necessary to dispose of a tremendous quantity of salt water in the later periods of production. There has been a gradual increase in the amount of salt water pro-duced in the field, until at present it is about 200,000 bbl. per day from approximately 4400 wells. It is only natural to expect an increase in the number of wells producing water, as well as the amount of water produced in the future, and it has been estimated that if present practices con-tinue the production of salt water may ultimately be as much as 700,-000 bbl. per day. The Woodbine sand is found in the East Texas field at an average depth of 3650 ft. The oil-bearing portion of the sand lies between the depths of 3050 ft. below sea level, on the east edge of the field, and 3320 ft. below sea level on the west, which depth was the estimated original average oil-water contact. The Woodbine sand under the field has the form of a broad tilted wedge pinching out on the eastern side of the field and dipping gently into the East Texas Basin toward the west. The Woodbine sand in the East Texas field has an average porosity of approximately 25 per cent and is highly permeable, the average being about 1300 millidarcys.

Jan 1, 1940

By R. T. Mishler

I WISH to express my keen appreciation of the article on the above subject by Coe and Clevenger.1 It has been doubly interesting to me, for the reason that the experience recorded and the principles evolved practically parallel the results of similar investigations made by myself and others at The Lucky Tiger Mine, El Tigre, Sonora, Mex. An outline of the work at El Tigre may aid in confirming the principles expressed by Coe and Clevenger. El Tigre has the unenviable distinction of possessing a slime with a much lower settling rate than any recorded in the article discussed. Under most favorable conditions the settling rate is about one-third that reported for the Liberty Bell mill, and one-tenth that reported for the Nipissing, Golden Cycle, and Presidio mills. This slow settling characteristic of Tigre ore has necessitated careful investigation of settling phenomena throughout the various evolutions of the plant. PREVIOUS SETTLING INVESTIGATION AT TIGRE During construction work at the mill, the Metallurgical Engineer in charge, D. L. H. Forbes, ran a series of experiments on settling. His tests proved that deep settling tanks were not ordinarily necessary. The use of tanks 2 or 3 ft. in depth was suggested.2 Later experiments demonstrated that the following principles of settling applied to Tigre pulp.3 1. In settling dilute pulp, settling rates are independent of pulp depth. 2. In settling thick pulp, settling rates are approximately proportional to pulp depth.4

Jan 3, 1917

By Richard H. Jahns

Terminology and Basic Specifications Minerals and closely allied natural substances that are used for personal adornment, as raw stock for the fashioning of ornamental objects, or for other decorative purposes can be referred to collectively as gem materials. Industrial gem materials are those employed directly in various areas of industry. Substances that are manufactured for gem or industrial uses are termed synthetic gem materials; most of these correspond in composition and crystal structure to certain minerals found in nature. Imitation materials are those whose use is based upon their resemblance to substances of different composition and greater value. Gem stone is a designation commonly restricted to those materials suitable for personal adornment, and the complementary term ornamental stone is applied to the remaining materials not used industrially. This distinction is arbitrary and somewhat inconstant, owing to numerous geographic differences and historical shifts in end uses. Further, there is a complete gradation between the category of ornamental stones and that of dimension stone. Although many building and monumental stones are undeniably ornamental in their uses, treatment of such material is beyond the scope of this chapter. Substances that lose their identity in use are excluded from the gem category. Thus a transparent crystal of beryl would not be classed as a gem stone if it were treated as a source of beryllium metal. The adjectives precious and semiprecious have been employed as a means of distinguishing different gem materials on the basis of their recognized value. Diamond, emerald, ruby, and sapphire consistently have been regarded as precious stones, and in cut form they commonly are referred to as the noble gems. Opal, pearl, turquois, and chrysoberyl also have been classed as precious at various times. In recent years, however, it has been increasingly recognized that no satisfactory distinction can be based upon assessed value or any group of intrinsic properties, and at the present time all gem stones normally are referred to as precious. Indeed, the tendency is to extend this term to include many of the so-called ornamental stones, and the designation semiprecious has been essentially discontinued. Unlike most mineral commodities of economic value, gem materials are little altered in processing for end uses. Some stones are used in essentially their natural form, and most are reshaped and polished without significant changes in their fundamental properties. Thus the preparation of gem and ornamental stones is intended chiefly to emphasize or enhance desirable characteristics that are present initially. The worth of most synthetic gem stones is founded upon the identity between their major properties and the natural characteristics of the corresponding minerals, just as the pleasing qualities of imitation stones depend upon how well certain of their properties simulate those of more valuable substances. The most important specifications of gem materials represent four basic factors: beauty, durability, rarity, and portability. Beauty, whether expressed as splendor, "purity," attractiveness, or in some other way, is mainly a function of personal response to optical properties such as color, transparency, indices of refraction, and dispersion. Freedom from visible imperfections is important for transparent stones. For some substances beauty depends also upon asterism, opalescence, textural and

Jan 1, 1960

By J. W. Rutter, K. T. Aust

The motion of individual grain boundaries under a constant driving force was investi,qated for zone-refined lead, with and without solute tin additions. The rate of boundary migration was found to depend strongly on tin content and on the orientation relationship between the adjacent grains. The results are compared with the theory of impurity-controlled grain boundary miqration developed by Lucke and Detert. Evidence was found that grain boundaries separating grains which have the Kronberg-U&apos;ilson orientation relationships of 38 and 22 deg about <Ill> and 28 deg about <100>, correspond to boundaries of high mobility. The results are discussed in relation to the formation of annealing textures in metals and the structure of high-angle boundaries. It is generally known that small amounts of impurities in solid solution greatly influence the re-crystallization behavior of metals. For example, the addition of 0.005 at. pct of tellurium to copper,&apos; or 0.005 at. pct of silver to lead,2or 0.01 at. pct of manganese or nickel to aluminum3 greatly decreases the rate of recrystallization of these metals. However, this effect may be the combined result of a decrease in the rates of both nucleation and growth; recrystallization experiments do not separate these two factors. Bolling and winegard4 determined the effects of small quantities of tin, silver, and gold on grain growth in polycrystalline zone-refined lead.

Jan 1, 1960

By W. K. Lewis, Lombard Squires, W. I. Thompson

The authors presented an article2† last year on colloidal properties of clay suspensions in which they attempted to sustain the position that the behavior of clay suspensions is due primarily to the mechanical interference of the platy particles, the nature and extent of the interference being profoundly influenced by the character of the surfaces of the particles, which in turn is determined primarily by the nature and amount of adsorbed foreign materials held on the surface of the particles by forces which are predominantly chemical in type. The following discussion is a continuation of that article to extend these same interpretative points of view to the behavior of clay gels. Insight into the mechanism of gelation is certainly of outstanding importance in the handling of drilling muds. In the former article it was suggested that the thin, flat plates that constitute the ultimate clay particles may build up aggregates by the overlapping of the ultimate plates face to face much longer and perhaps also much wider than the ultimate plates themselves, but not appreciably thicker. Exhaustive microscopic examinations of characteristic clays show no tendency for the larger particles, clearly visible under the microscope, to orient themselves in this way. It is true that the gelation of the clays is due primarily to the smallest particles, unresolvable other than by the ultramicroscope, so that the possibility of the deve1opment by them of an overlapping structure is not excluded. Furthermore, as one approaches the limit of resolving power of the microscope, the difficulty of observing accurately the shapes and relative positions of particles incresses excessively. However, in the absence of any observable tendency toward overlapping orientation of the large, visible particles, one hesitates to ascribe such a tendency to the smaller particles beyond the range of visibility. Should it develop that one must exclude the assumption of overlapping orientation, the explanations offered in the previous article are changed in only one respect; namely, one would now have to assume that the ultimate particles themselves have length, and probably also width, very large in comparison with their thickness.

Jan 1, 1936

By L. L. Wyman

The resultant embrittlement caused by the exposure of oxygen-bearing copper when hot and exposed to reducing gases has been the subject of many studies.&apos; Little attention, however, has been given to the possible embrittling effects due to atmospheres or conditions that under some circumstances might be the source of a reducing gas. At rather infrequent intervals there occur reports of copper becoming embrittled during normal annealing cycles in commercial steam-atmos-phered furnaces such as customarily are used for this operation. As might be expected, several other factors exist—such as oil, dirt on the wire, or in the furnace, or metallic surface contacts—that might produce reducing gases and be the source of the trouble. However, in consideration of the statement made by Ruder,2 it would seem that under some conditions steam itself might prove to be the source of trouble. A consideration of the amount of the dissociation of water vapor up to temperatures of the melting point of copper shows that3 the amount of hydrogen that could come from this source is far too minute to account for any embrittlement. What such information does not tell is what will happen at the surface of copper when subjected to steam at elevated temperatures, for entirely different conditions may persist, which would account for Ruder&apos;s observation. Furthermore, there are no data as to what might happen at the surfaces of other materials present, the resultant of which might affect the condition of the copper present. For this reason, it was decided to make a series of experiments comparable to those previously conducted by the writer,&apos; which would clarify the effect of the steam on copper, and in copper in the presence of steel. Material The material used in these experiments was tough-pitch copper wire of rectangular cross section, about % in. thick, picked at random from the regular factory production of material used for windings, etc., in the electrical industry. Chemical analysis of this material gave the follow-

Jan 1, 1940