Search Documents

By Clyde Wyman

THERE has always been a question as to the extent to which oxidizable alloys might he recovered from charged scrap in the, acid electric furnace. While qualitative information was not lacking, the quantities that might be recovered and the conditions best suited for such recovery were not clearly defined. The present investigation was carried out to determine the efficiency of alloy recovery from residuals contained in the bath, especially in regard to the recovery of vanadium. A series of 24 heats was produced at the Burnside Steel Foundry Co., including medium manganese-molybdenum-vanadium, manganese-chromium, and grade B steels, in which vanadium recoveries from the residual vanadium were investigated. Recoveries of other alloys were also studied from the accumulated data. These heats were produced in a 5-ton acid-lined electric furnace. The analysis of metal and slag samples and the micrographs were prepared by the Research Laboratories of the Vanadium Corporation of America. In addition to the vanadium contained in the scrap charge, ferrovanadium was added to the charge and to the molten bath to bring the residuals up to the desired level. Vanadium pentoxide (V2O5) in one series of heats was added to the bath after meltdown, for the same reason. In addition to the general furnace practice, the slags of these various heats were treated with coke breeze, Ferrocarbo-S (silicon carbide), and aluminum dross to determine the effects of different reducing agents upon the alloy recoveries and upon the final product.

Jan 1, 1947

By Lawrence H. Van Vlack, Otto K. Riegger, Gerald I. Madden

The microstructural variations of periclase (MgO) in the presence of oxide liquids are examined under the steelmaking variables of: 1) temperature, 2) liquid composition, and 3) FeO additions under different oxidation levels. Attention is given to the distribution of the phases, both liquid and solid, and to the growth of individual crystalline grains. Silicate liquids penetrate more extensively between individual periclase grains than do liquids containing high percentages of Fe2O3 Higher MgO solubilities in the liquid and lower MgO contents of the solid favor more rapid grain growth. The presence of a second solid phase reduces the periclase grain growth rate and increases the amount of the solid-to-solid contact within the oxide microstructures at high temperatures. The service suitability of a refractory depends on many factors. Two are of major importance and include 1) the thermal resistance to melting, and 2) the mechanical resistance to loads at service temperatures. Neither is a simple consequence of the service temperatures because service conditions will alter compositions, produce partial melting, and induee phase changes. Consequently, the equilibrium phase relationships have been rather thoroughly studied and give a knowledge of the thermal resistance to melting, but do not give full information about the mechanical properties because two refractories with the same types and quantities of phase may have different microstructures. Although variations of microstructures with time, temperature, and composition have been subjects for extensive investigation in metals, only a limited amount of comparable microstructural work has been performed for refractory materials.' This study was an attempt to evaluate some of the consequences of service parameters upon the microstructures of refractories so that bases may be established for the analyzing of high temperature mechanical properties. Periclase (MgO) was chosen as the refractory oxide; variables included those which are encountered under steelmaking conditions such as 1) temperature, 2) liquid composition, and 3) FeO additions under various oxidation levels. Specific attention was given to the distribution of the phases, both liquid and solid, and to the growth of individual crystalline grains. The most closely related work on microstructures of polyphase materials is that of Van Vlack and Rieg-ger2 on the microstructure of magnesiowüstite [(Mg,Fe)O] in the presence of silica. In that work which pertained to solid solutions with less than 40 pct MgO, most of the quantitative work was performed on FeO microstructures. The chief conclusions concerning these relatively low-melting oxide solids were as follows: 1) the rate of crystalline grain growth is inversely proportional to the grain diameter, 2) grain growth proceeds more rapidly at higher temperatures but is slightly retarded by additional liquid content, and 3) a Silicate-containing liquid penetrates as a film between the individual magnesiowüstite grains independent of time, temperature, amount of liquid, or the MgO/ FeO ratio. The above observations are in contrast to prior work3 on the microstructure of silica in the presence of iron oxide-containing liquids where the liquid does not penetrate as a complete film between solid grains. The phase relationships for the compositions of the present work are shown in Fig. 1 which is a summary of the work of several investigators.4 Of importance is the fact that CaO forms a more stable structure with SiO2 and Al2O3 than do either MgO or FeO. The oxygen potential has little effect on periclase unless iron oxide is also present. The iron oxide is ferrous at moderately low oxygen levels, changing to ferric as the Oxygen potential is increased so the spinels, magnetite, and magesioferrite are formed.5 These two phases are relatively stable in air at steelmaking temperatures. I) EXPERIMENTAL PROCEDURE ractory were made with reagent grade Oxides. The magnesium oxide used was 99 pct MgO after ignition, and the iron oxide raw material had a minimum content of 99 pet Fe2O3. The CaO, SiO2, and A12O3 were also reagent grade raw materials. After mixing, the required compositions were pressed into pellets at a minimum pressure of 5000 psi to insure compaction of the raw materials and prevent excess void content. A silicon carbide element tube furnace was used with thermocouple control for sin-

Jan 1, 1963

By T. S. Plaskett

A striated structure perpendicular to the growth axis was observed by the copper-decoration tech-nique in dislocation-free, .float-zoned silicon crystals. The striations, which were spaced about 100 p apart, fitted the relationship d = f/u , where d is the spacing, f is the growth rate, and u is the crystal rotation rate. Each stria was resolved into an UNDOPED silicon crystals pulled from quartz crucibles by the Czochralski technique usually exhibit a striated structure perpendicular to the growth axis.'-' This structure has been attributed to oxygen segregation, with the oxygen being introduced from the quartz crucible. If the crucible is rotated, the level of oxygen contamination has been reported as high as 10° atoms per cu cm.10 These striations are similar to solute striations commonly observed in doped Czochralski-grown crystals. The periodic nature of the striations is caused by a periodic variation in the growth rate",12 which is attributed mainly to thermal gradients in the melt.13 A finer striated structure14 attributed to constitutional supercooling is sometimes observed between the coarse striae. The oxygen striations have been observed by infrared transmission techniques,' by the copper-decoration technique,' by X-ray diffraction microscopy,6-8 and by 9 p absorption measurements3 on crystals pulled from the melt both with and without dislocations. In this investigation float-zoned dislocation-free crystals were examined by the copper-decoration technique. The level of oxygen for float-zone material is less than 1016 atoms per cu cm the lower limit of detection by 9 p absorption measurement. EXPERIMENTAL TECHNIQUE The crystals were grown by the float-zone process with the rf heating coil outside of the quartz envelope containing the silicon. All float zoning was done under an atmosphere of purified helium. The Dash technique15 was used to grow the crystal dislocation-free. This involves growing the crystal initially with a diameter between 2 and 3 mm and at array of starlike precipitates of copper. The strucLure was not .found at the surface tor a depth of about 1.5 mm, or in a region of similar width ahead of a dislocation network. The structure is postulated to consist of vacancy clusterings or dislocation loops. very rapid rates, about 20 mm per min, for a distance of about 3 cm. The diameter of the crystal is then increased to the diameter of the source of silicon, which in this case was about 19 mm. Because of the arrangement of the apparatus, the zone was passed downward rather than upward, contrary to the standard float-zoning practice. Also, the source was rotated rather than the seed. ziegler17 has made dislocation-free crystals by a similar technique but has passed the zone upwards. The starting material was zone-refined and had a p-type resistivity of 150 ohm-cm. The major impurity was boron; the total impurity excluding the boron was reported by the supplier (Dow-Corning) to be typically less than 2 x 1013 atoms per cu cm. The crystals were examined by the Dash copper-decoration technique18'19—a method in which about 10" atoms per cu cm of copper are diffused at a temperature between 900" and 1000°C into silicon which is then quenched to room temperature. On quenching, the copper precipitates on crystalline defects which are then visible when viewed by transmission infrared microscopy. The photomicrographs shown were taken either of the infrared image tube screen or directly on infrared film. All sections prior to decorating were chemically polished and, for some sections, given a sirtlZ0 dislocation etch-pit examination. After decorating, the samples were mechanically polished. RESULTS A photomicrograph, taken in transmission of a decorated cross section, is shown in Fig. 1. The portion of the section shown is near the surface of the crystal. The entire cross section showed no dislocation etch pits after being given a Sirtl etch treatment. It is seen that the copper precipitated randomly. Each precipitate, as has been reported by others, was found to have a starlike structure.

Jan 1, 1965

By E. H. Rose

IN the realm of ore dressing the most pregnant feat of all time was announced in 1945: the winning of the mineral raw materials which made the harnessing of atomic energy possible. Lost in the stupendous implications of the end result, in the two billion dollar hugeness of the project, and in the famous names attached thereto, the fact that crude uranium ores had to be concentrated received relatively little notice in the press. Only the final link in the concentrating chain was publicized-ether extraction of uranyl nitrate, developed by Hoffman and carried on by the Mallinckrodt Chemical Works, or methods developed by the Ames group under Spedding. Some of the earlier links represented less glamorous but equally difficult and exacting research. One may only speak a word of admiration for those who worked hard, accomplished much, and said nothing. The universal lament for most of the year was "man shortage." A group of Canadian engineers expressed it as "being so short of labor that no labor was available to develop laborsaving devices." . Despite this, an outstanding amount of mineral-dressing progress was made in 1945. Necessity allowed no alternative. The insatiable demand of war for minerals forced the exploitation of lower and lower grade ores, and of others not before considered of commercial character or use, requiring the mineral dresser to fight for and win new bridgeheads on the home front.

Jan 1, 1946

By J. E. Willson, N. K. Bohidar

An evaluation of internal stress distribution based on photoelastic studies and destructive testing of simulation models shows that pillar failure is a function of the internal stress distribution, and that stability can be changed by altering the internal stress pattern. Induced stresses in three-dimensional epoxy disks subjected to uniaxial forces were evaluated by photoelastic studies. Stress profiles across different sections perpendicular to the loading direction revealed two maxima for each profile. Based on the stress distribution for the entire column, an attempt was made to explain pillar spalling and the hour glass pattern of failure in a mine pillar. For maximum stability and optimum design of mine pillars, it is necessary to consider the external forces, the nature and distribution of induced stresses and the characteristics of the pillar material as determined in the laboratory. This paper summarizes the research done by N. K. Bohidarl and Ben L. seegrniller2 as partial fulfilment of the requirement for Master of Science degree in Mining Engineering, University of Utah. It is an evaluation of a study to determine the stress distribution in short columns in order that regions of high stress concentration in mine pillars may be found and their effect on pillar failure be ascertained. The ratios of the dimensions of the columns studied are representative of those found in mines located in flat-bedded deposits. The weight of the overburden generally constitutes the major external force. This force is calculated by taking into account specific weight and thickness of the cover. Determination of the distribution of this force on pillars may often require a complex analytical study. There have been many investigations of the strength

Jan 1, 1968

By H. E. Nold

THIS paper is an effort to explain in a simple manner the fundamental principles involved in examining a clay deposit for both quantity and quality and in operating a clay mine, either open-pit or underground, so that the best quality of finished material can be made from the raw material available. The writer is aware that what is recommended in this paper is everyday practice in many refractories plants and in some other heavy-clay products plants, but observations made while visiting practically every clay mine in Ohio have convinced him that the practices herein discussed are not as widely used as their importance warrants. It is true that the problem of mining for quality is more acute in refractories plants than in most heavy-clay products plants, yet some of the latter are finding it profitable to pay more than ordinary attention to the selection and blending of their raw materials. It is hoped that this short paper may prove helpful to some who are now finding it difficult to produce a uniform product of as high quality as their clay deposit seems to warrant. The coordination of the work of the clay mine or pit with the manufacturing plant, to the end that the best product possible be made from the raw material available, presupposes a rather intimate knowledge of the clay deposit. The knowledge must include not only information of the amount of clay-available but also rather detailed information about both vertical and horizontal variations in quality of the clay. This information should cover three things: quality, quantity, and location.

Jan 1, 1929

By C. G. Dunn, M. Sharp

HE orientations of 137 crystals of copper pro-T duced by secondary recrystallization in a cube texture matrix have recently been obtained. Although the crystals were not prepared for the purpose of determining a secondary recrystallization texture, the orientations obtained proved to be rather interesting, as they confirmed, in part, published results and also disclosed additional preferred orientations in the texture. The investigation of Dahl and Pawlek,&apos; Bowles and Boas,&apos; and Kronberg and Wilson3 showed respectively that the orientations of secondary grains growing in a cube texture matrix were related to those of the primary grains by a rotation of approximately 30" about [001], the rolling direction, by 30" about a <111> direction, and by either 22" or 38" about a <111> direction. Kronberg and Wilson also obtained a component of the texture similar to that of Dahl and Pawlek except the angle of rotation about [001] was 19". When the cube texture matrix was deformed a small amount, Kronberg and Wilson also obtained large grains on subsequent annealing corresponding to a rotation of 15" about the normal to the sheet, but these grains should not be classified as secondary recrystallization grains since they were produced subsequent to mechanical straining. The particular texture obtained, of course, depends on the composition of the copper and the processing schedule employed, since these factors markedly affect the primary recrystallization texture and the sharpness of any cube texture produced. In the present investigation, pieces of OFHC copper in the form of M in. round bars were cold forged to a thickness of about 0.40 in., annealed 1 hr at 350°C in an atmosphere of hydrogen, and cold rolled crosswise to a thickness of 0.200 in. These pieces were given a penultimate anneal of 1 hr at 350°C in hydrogen and a 90 pct cold-rolling reduction lengthwise to a thickness of 0.020 in. Indentations generally were put in one end of the as-cold-rolled strips to promote earlier formation of secondary grains.

Jan 1, 1953

By A. W. Hahn

ALTHOUGH enormous tonnages of sulfide lead and lead-silver ores are treated by flotation, the products of flotation mills treating oxidized ores of lead and silver are almost negligible. However, each year there is a slight tonnage increase, and it is possible, should a sizeable oxidized lead ore tonnage be developed, the field will become an important one. In 1918, the Shattuck-Arizona Copper Co. erected a plant at Warren, Ariz., for the treatment of oxidized gold-silver-lead ores. Glenn L. Allen worked out the metallurgy for this plant, employing tabling, followed by flotation concentration. The Shattuck-Denn Mining Co., successors to the Shattuck-Arizona Co., now employs straight flotation in the same mill, treating about 200 tons daily. In 1922, the San Diego mill of the American Smelting & Refining Co., in the Parral district, Chihuahua, Mexico, started operating a 600-ton mill on a mixed sulfide-oxide gold-silver-lead ore. Tables and flotation are used here, and about 200 tons of oxidized slime treated by flotation. In 1923, the Eureka Holly Mining Co. started operating a 90-ton mill at Eureka, Nev., using tables and flotation, on an oxidized lead-silver ore. In 1924, the American Smelting & Refining Co. started a 250-ton mill in northern Peru, to treat a high grade oxidized gold-silver ore with very low lead values. In 1924, the Grand Central Mining Co. started a 200-ton flotation mill on old oxidized gold-silver-lead tailings at Fairbank, Ariz. In 1926, the Compania International Minera, a subsidiary of the Union Corporation of London, started a 250-ton flotation mill on oxidized lead-silver ores, and during April of this year, the Phelps-Dodge Corp. will probably start a 250-ton mill at Warren, Ariz., on oxidized lead-silver ores, similar to those being treated in the Shattuck-Denn mill.

Jan 1, 1927

By P. A. Boeck

Discussion of the paper of P. A. BOECK, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 104, August, 1915, pp. 1539 to 1550. LAWRENCE ADDICKS, Douglas, Ariz.-It does not seem to me that the role played by carrying heat away from one surface to another has been brought out. A cellular construction prevents the motion of air currents. Also in the installation on the top of a reverberatory furnace, that Mr. Krieger mentions, where it stopped the cooling, there is besides the question of overheating. Another complex question, entirely apart from the necessity of not carrying a brick above a certain temperature, is that of not allowing acids and bases to come together at too high a temperature. J. W. BECKMAN.-What cements together the individual cells in the insulating material? Also, how does the material behave in the presence of acids and alkalies, both strong and weak? A. H. KRIEGER, New York, N. Y.-The material is formed or composed of myriads of lace-like skeleton remains of diatoms visible only -under a powerful microscope. The diatom lives in salt and fresh water. On the Pacific Coast there must have been an abundant life of the diatom, because the beds, still in existence in Southern California, are fully 1,000 ft. through, and are hard and strong, standing a pressure of more than 400 lb. per square inch. The beds must have been many ages in forming and the diatoms have become firmly packed together. The samples shown are typical of the entire deposit as it was formed at the bottom of the sea. Once this structure has been destroyed, it is impossible to reconstruct it without artificial bonding materials. With the exception

Jan 12, 1915

By Robert G. Johnson, Richard J. Prosen

THE present work was done in connection with a program for investigating metal-to-ceramic braze techniques using the well-known reactivity of titanium with certain ceramic oxides. The investigation extended over the range of 0 to 30 pct Ti. The indium was obtained from the Indium Corp. of America and was specified to be 99.97 pct pure. The titanium was supplied by Metals Disintegrating Co. and was stated to be 99.5 pct pure. Each 2 to 4 g quantity of the alloy compositions studied was prepared using a mixture of 300 mesh powders pressed into pellet form. The pellets were heated in thin-walled molybdenum crucibles using a resistance-wound furnace in a vacuum less than 10-4 mm of Hg. Little reaction occurred between the molten alloy and the crucibles at the temperatures and short time intervals used. Only slight spectroscopic traces of molybdenum were found in the melt after a typical period of heating. The points shown on the phase diagram of Fig. 1 represent thermal arrest measurements. The phase boundaries shown are consistent with the thermal arrest and X-ray data obtained. The temperatures were determined using a Pt-Pt 10 pct Rh thermocouple with the junction spot-welded to a short molybdenum rod. The rod was almost completely immersed in the liquid metal, so that good thermal contact with the melt was achieved. The small mass of the crucible and its contents made it possible to obtain many heating and cooling curves in a few minutes time, an advantage which helped to minimize the effects of indium evaporation at the higher temperatures. A Brown strip chart recorder was used to display the thermal arrest curves. To check the technique, the melting point of 99.999 pure Al was measured and found to be within 1 of 660.2c, the accepted melting point. The upper limit of temperature with this technique was about 900°C beyond which the evaporation rate of indium became great enough to alter appreciably the alloy composition during the runs. A peritectic transition was found at 796°+ 5°C from 1.5 to 30 wt pct Ti. It was not found at 0.5 or 1.0 pct. A small super-cooling effect was observed. The melting-point transition to the B + L phase was found up to 20 pct Ti but not at 25 pct. Within the 1 deg accuracy of the measurement, the transition temperature was that of pure indium, 156°C. The liquidus line to the left of the 1.5 titanium point was located only approximately. The two crossed circle points at 1.0 and 0.5 pct Ti place a lower limit on the liquidus line and were determined by observing visually the cessation of vibrations in the melt caused by the damping effect as B-phase crystals were formed during cooling. The B-phase boundary was found at 23.8 pct Ti by X-ray analyses of small single crystals of the B phase isolated from 2 pct Ti melts. The compound was found to be Jetragonal with lattice dimensions of c = 3.052A and a = 10.094W. From the unit cell dimensions and the measured density of 6.42 i 0.05 g per cc, the compound was determined to be In4Ti3 which has 23.8 pct Ti. The calculated density of 6.44 g per cc is obtained assuming 2 mol

Jan 1, 1962

By J. W. Halley

Copper has frequently been recommended as an alloying element for steel and the precipitation-hardening of steels containing from 1 to 2 per cent copper has been studied by a number of investigators. The straight copper steels, however, have not been used extensively and little advantage has been taken of the precipitation-hardening of complex steels containing appreciable amounts of copper. It is difficult to produce a satisfactory surface on the straight copper steels and undoubtedly this has discouraged their use. During recent years a number of steels containing enough copper to make them susceptible to precipitation-hardening have been put on the market. These steels belong to the group usually referred to as "low-alloy high-tensile " steels. They were designed for use in the " hot-rolled" condition; transportation equipment and large structures that cannot be readily heat-treated have been their chief application. Little emphasis has been placed on the possibility of strengthening those containing substantial amounts of copper by precipitation-hardening. The present investigation was undertaken to determine the precipitation-hardening characteristic of one of the "low-alloy steels." Previous Work The first complete study of the effect of time and temperature on the precipitation-hardening of plain copper steels was made by Nehll in 1930. At about the same time Bucholtz and Koster2 studied copper-chromium steels but did not determine the relation between time and temperature to produce maximum hardening. Later, Smith and Palmer3 determined the rate of hardening at various temperatures for two I per cent copper steels containing different amounts of carbon. Their tests indicated that the higher carbon content decreased the rate of hardening. They made tests on many steels containing other alloying elements in addition to copper, but did not determine the time-temperature relationship for maximum hardening for any of the complex steels. Norton,4 in studying the limit of solid solubility of copper in iron, determined the time for maximum hardening of a 2.06 per cent Cu iron

Jan 1, 1940

By V. R. Garfias

A survey of the resources of mineral fuels, coal, petroleum and natural gas presupposes a clear distinction between the known amount underground and the "proven reserves"; the&apos;portion that can be economically brought to the surface and made available for utilization. Only a fraction of the coal and petroleum in producing fields is or can be economically brought to the surface and not all of this is economically utilized; also, although practically all the natural gas can be economically recovered and utilized, in actual practice a large part of the total volume that reaches the mouth of the wells is wantonly blown into the air and wasted. It is thus estimated that of the total amount of coal underground about 40 per cent remains unrecovered, or is otherwise wasted, before it reaches the consumer; that only some 25 per cent of the petroleum in proven fields is actually brought to the surface; and that even if practically the entire volume of natural gas can be economically utilized, in actual practice close to 25 per cent of the total produced is now absolutely wasted. And the dissipation of this gas, unwarranted as it is, not only diminishes the gas supply but diminishes also the proven reserves of petroleum from such fields as the Panhandle of Texas, where petroleum and natural gas are produced simultaneously. Many factors affect the estimates of the proven reserves of mineral fuels, such as the capacity and nature of the reservoir, its depth, the quality of the product, the efficiency of recovery, the price of the fuel and its byproducts, etc., etc., but superseding at times all of these in connection with petroleum and natural gas deposits is the effect of "subsoil ownership" on the rate and methods of exploitation of the deposits. As a result it should be a comparatively simple matter to eliminate waste and overproduction, and thereby increase the proven reserves of petroleum and natural gas, in Russia, Iran and Iraq, where the subsoil rights are nationalized, or in any country in which there is or can be quickly established an effective legal control of the underground deposits and the manner of their exploitation. It has been and it is now, on the other hand, almost an impossible undertaking to intelligently regulate the petroleum and natural gas production in the United

Jan 1, 1935

By Elmer W. Pehrson

The term "survival" in the title means the preservation of a society in which men are free from the political and economic restraints that characterize totalitarian systems, be they communist, socialist or facist. It means the ability to withstand the enemy&apos;s offensives in the fields of propaganda, commercial competition and, if necessary, war. The temptation to substitute "victory" for "survival" is great but a realistic appraisal of the creeping socialism and demagoguery that pervade our time indicates that we may have to be content with survival in status quo. "Mineral strength" means assurance that adequate supplies will be available to meet all the contingencies of cold and hot wars. The overall mineral position of the U. S. viewed in the light of these premises is far from secure. It is true that we are the leading producing and consuming nation of the world, but the Soviet Union is gaining and the Sino-Soviet Bloc confronts us with a sobering potential. The emergence of the Common Market in Europe as an economic and political unit places a third independent entity into the competition. Our total mineral output continues on an up- ward trend but the reverse is true in certain strategic commodities. Moreover, consumption is moving ahead faster than production so that there is increasing dependence on imports which has significant adverse geopolitical connotations. There is widespread belief that our resources can at least maintain present levels of self-sufficiency during this critical period in world history, but social dreamers, the labor monopoly, and trade and taxation policies have discouraged aggressive activity in exploration and development, and access to essential foreign sources is threatened by a variety of circumstances. Our stockpiles, belatedly built up to achieve minimum protection against shortages in time of war, are under. political attack and threatened with partial destruction on the basis of what are at best uncertain assumptions regarding the new: look of global warfare.

Jan 11, 1962

By W. H. Corbould

The township of Cloncurry is situated in the northwestern part of Queensland, about latitude S. 20" 42&apos; 53" and longitude E. 140" 30&apos; 25". Townsville is the port through which all the trade passes and is about 470 miles east-northeast of Cloncurry township. The Cloncurry copper district covers an area about 200 miles long by 40 miles wide. Unfortunately the mines are very scattered over this area, there being no large groups of mines. Mount Elliott mine is situated about 70 miles south from the township of Cloncurry, and Mount Oxide mine about 150 miles north of Cloncurry. The district has been known for the last 35 years, and in the early stages a large amount of capital was expended with little to show for it; but within the last four years the railway has been extended from Townsville to Mount Elliott and about 40 miles north of Cloncurry, which has made possible the treatment of the ores of the mines on this extension. The Mount Elliott company within the last few years has smelted and converted on its mine 169,688 tons of ore for 20,554 tons of blister copper, containing 20,377 tons of copper, 35,642 oz. of gold and 28,841 oz. of silver, at a cost of about 233 per ton of blister copper, f.o.b. Townsville. This cost included all development, wages, salaries, general management, office, agency, legal expenses, freight, etc. The gold and silver contents would practically pay for freight to Europe, refining, realization charges, etc. The costs of supplies are as follows: Firewood, 15s., coke, 75s., mine timber, 54s., and coal, 60s. per long ton; explosives: dynamite and gelignite, 50s., and blasting gelatine, 65s. 6d. per case, Mount Elliott Mine The pay shoot of the orebody outcrops at the surface for about 200 ft., and lies between two slate walls about 40 ft. apart., having a general

Jan 1, 1915

By J. W. Halley

Copper has frequently been recommended as an alloying element for steel and the precipitation-hardening of steels containing from 1 to 2 per cent copper has been studied by a number of investigators. The straight copper steels, however, have not been used extensively and little advantage has been taken of the precipitation-hardening of complex steels containing appreciable amounts of copper. It is difficult to produce a satisfactory surface on the straight copper steels and undoubtedly this has discouraged their use. During recent years a number of steels containing enough copper to make them susceptible to precipitation-hardening have been put on the market. These steels belong to the group usually referred to as "low-alloy high-tensile " steels. They were designed for use in the " hot-rolled" condition; transportation equipment and large structures that cannot be readily heat-treated have been their chief application. Little emphasis has been placed on the possibility of strengthening those containing substantial amounts of copper by precipitation-hardening. The present investigation was undertaken to determine the precipitation-hardening characteristic of one of the "low-alloy steels." Previous Work The first complete study of the effect of time and temperature on the precipitation-hardening of plain copper steels was made by Nehll in 1930. At about the same time Bucholtz and Koster2 studied copper-chromium steels but did not determine the relation between time and temperature to produce maximum hardening. Later, Smith and Palmer3 determined the rate of hardening at various temperatures for two I per cent copper steels containing different amounts of carbon. Their tests indicated that the higher carbon content decreased the rate of hardening. They made tests on many steels containing other alloying elements in addition to copper, but did not determine the time-temperature relationship for maximum hardening for any of the complex steels. Norton,4 in studying the limit of solid solubility of copper in iron, determined the time for maximum hardening of a 2.06 per cent Cu iron

Jan 1, 1940

By James E. York

The honor so fairly earned and so incompletely and tardily paid to Henry Cort, the inventor of the puddling-furnace and the rolling-mill, has been fully set forth by Mr. Charles H. Morgan,&apos; and needs no further emphasis here. In view of the importance of the rolling-mill in the treat ment of iron and steel, the paucity of information concerning it is surprising. With the exception of a book, written about 35 years ago, by Peter Ritter von Tunner, an Honorary Member of this Institute, and of desultory articles on simple sections, which have appeared in technical journals, I know of no publication attempting to treat this subject, although volumes have been written on the scientific theory and technical manipulations involved in other branches of the iron- and steel-industry. This strange anomaly may be due to the fact that roll-turning cannot be called a scientific business. It does not ordinarily come within the range of an educated engineer; yet it cannot be performed by an ordinary mechanic. It demands some of the qualifications of an engineer, in designing, and those of a mechanic, in execution. The men who have followeci this trade have controlled the training of their successors. In many cases the technical knowledge required has

Jan 1, 1907

By John Howe Hall

The recently announced run of three years, nine months and eleven days made by a crucible steel melting furnace of the Columbia Tool Steel Co., which is claimed as a world&apos;s record, brings forcibly to our attention the great improvements that have been made in the design, construction and operation of the Siemens regenerative crucible melting furnace since its introduction in this country. Credit for this advance should be given to the furnace designer, the manufacturer of refractories, and the operators, of the furnaces, whose persistent efforts and intelligent co-operation in attacking the problem have resulted so satisfactorily. There are three factors that determine the life of a crucible furnace, or any other furnace for that matter: Design, nature of refractories, and conditions of operation (including the nature of steel melted); and to some extent these factors are interdependent. Thus, for instance, if a crucible furnace is to be operated single turn and allowed to cool off considerably at night, in order to save fuel, the use of clay-brick melting holes may be advisable, since silica brick is not well adapted to endure repeated heating and cooling. But the total life of a clay-brick melting hole is necessarily short. Again, if local conditions such as danger of flood make necessary the building of the furnace largely above ground, so that the radiation of heat is promoted, the cooling down of the furnace over the week ends, when no steel is melted, will be considerable—and the contraction of the furnace that results tends to wrack it to pieces. The character of the metal being melted affects the life of the furnace to a great extent. Low-carbon steels and steels made from iron and charcoal require higher temperatures and much longer melting time than high-carbon steel or steel made largely from scrap; the life of the furnace will be shorter, and the number of heats melted will be much less, when such materials are melted. The figures available, showing the life of furnaces, are for this reason especially not strictly comparative, since the variations in the steel melted undoubtedly affect the life to a greater or less extent. Probably, however, the method of handling is as important a factor

Jan 1, 1914

By Robert M. Jimeson

At the recent SME Fall Meeting in Salt Lake City, Robert M. Jimeson, Physical Science Administrator of the U.S. Bureau of Mines, cited the research programs underway in the Bureau&apos;s Division of Coal Research, and outlined their current status. These research programs have been selected by the Division because of their relative value and high probability of success in contributing to the conservation of the Nation&apos;s coal and to the expanded use of coal in current or new markets. Since about 50% of coal consumption in the United States is in the production of electric power, 20% in production of metallurgical coke, and over 20 % by industry in producing process steam and power, the Bureau has placed much emphasis on research that will maintain coal&apos;s leadership in these established areas. This emphasis is reflected in the projects discussed on these pages. Bear in mind that this survey is not all-inclusive. Other projects underway include studies on furnace performance factors, improved burner design, and other critical boiler work which can be used immediately by industry to improve efficiency of current practices in power generation; other investigations are aimed at reducing fireside deposits and corrosion of boiler and super- heater tubes, fly ash utilization, and control of SO, from flue gases (a major step in preventing air pollution). These plus many other projects during the past years have served to focus attention on the fact that the U. S. Bureau of Mines is presently making the largest single contribution to this Nation&apos;s coal research effort.

Jan 11, 1963

By Alfred James

John Stewart MacARthUr, born in 1856, was the son of Robert MacArthur of Glasgow, and came of Scots stock distinguished for character and religious conviction. His election as elder of the Free Kirk gave him greater pride than the receipt of the gold medal of the Institution of Mining and Metallurgy. The former honor was for character— it marked him as a son worthy to follow in his father&apos;s footsteps; the latter was awarded for his life work of eminent service to the gold industry. Cheery optimism, resolution, tenacity of purpose, and industry ever characterized his actions. Apprenticed to the Tharsis Sulphur & Copper Co., his work on the chemical staff brought him to the notice of the Cassel Gold Extracting CO.,. at that time struggling with an unworkable electrolytic process..He was engaged by that company, in 1886, as technical manager and before long brought out the perchloride process, which was speedily followed (in 1887) by the epoch-making cyanide process. This process revolutionized gold mining and directly led the way to the elevation of the mining engineer to the most broadly trained product of the engineering profession. A noteworthy feature of the cyanide process was its completeness when introduced. Over thirty years have elapsed and the use of the process has been worldwide, but no suggested improvement has stood the test of time. The extension of the process to the beneficiation of silver ores—containing far more metal per ton and thus requiring the employment of stronger solutions—has brought us the Merrill and Crowe improvements in precipitation and the Nipissing desulfurization process for certain silver-hearing minerals. Roasting apparatus, fine crushing, filtration, and settling equipment have all aided the extension of the process in and from its original field. As Hennen Jennings put it,, the cyanide process today is essentially that of 1890. This self-containedness of the cyanide process arose from no mere chance; it was directly due to MacArthur. It was he who personally investigated every known method of precipitation and then every form of zinc from sheet, punchings, filings, millings, rods and shaving down to fume; it was he who investigated the effect of protective alkalies, of so-called accelerators, and of the addition of lead salts; he was determined to leave nothing to chance.

Jan 1, 1921

By H. E. Doerr

THE writer has been unable to find much information relative to tests made to determine the effect of forging on the specific density of steel. The opinion, however, among men engaged in the business, seems to he that forging greatly compresses or consolidates the steel. While such is doubtless the case with spongy or porous steel, the following experiments indicate that there can be little or no change in the density with steel initially free from cavities: Ten ingots of basic open-hearth steel cast as shown in Fig. 1 were used in the experiments. All the specimens were 0.53 carbon with all other elements the same, the analysis being determined from drillings taken midway between the center and outside of the upper end, as shown in Fig. 2. The specimens were selected from over one thousand ingots so that the tests could be comparative for the work done in forging only, but no two of the ingots were cast in the same heat. Each ingot remained in the mold approximately 30 min., when it was removed and air-cooled. About 12 hr. later, when the temperature had been reduced to approximately that of the surrounding atmosphere, the head was discarded and the ingot heated in an oil furnace to approximately 2250° F. (1235° C). Approximately 1 min. was required to forge under the steam hammier to 1 ¼ in. (31.75 mm.), rough diameter, as shown by the dotted lines in Fig. 2. All ingots were allowed to air-cool after forging. Cylinders ½ in. (17.7 mm.) in diameter and ½ in. high were then turned from the forged and unforged parts of the ingots and numbered. The ten pairs of specimens were submitted to Louis E. Endsley, Professor of Railway Mechanical Engineering, University of Pittsburgh; A. N. Talbot, Professor of Applied Mechanics, University of Illinois; L. Z. Slater, chief chemist, Scullin Steel Co., St. Louis, Mo. No in-formation was furnished as to which specimens were forged or unforged and each laboratory used the same specimens, submitting the average of three independent determinations, a tabulation of which is shown in the accompanying table in which the laboratories are designated by

Jan 1, 1919