Search Documents

By Edgar Trask

EACH branch of engineering seems to depend on the cooperation and contribution of some other branches to enable it to produce more efficient methods and appliances for man to use. The purpose of this paper is to show approximately the gain in efficiency of self-propelled merchant ships when steel of greater elasticity is substituted for mild steel in some of the strength members and alu-minum alloy is substituted in some of the parts where strength is not essential. The new steel will have some greater strength and a much greater elastic limit in the as-rolled condition, and must be readily weld-able under ordinary conditions of shipbuilding. Naturally, its cost may be more than mild steel, but if the demand is great that excess cost may be reduced to an amount that will make its use more economical than that of the present mild steel. There appears to be a well defined axiom in engineering today that to use the least power to carry a given load the weight of the carrier must be reduced to a minimum. This minimum must be, of course, consistent with the necessary strength, rigidity and durability and it must not be attained at an excessive cost where the fixed charges of the carrier will exceed the savings in, operating the motive power. Recent railroad equipment is a notable example of this, and in these trains alloy steels and aluminum together with less weight per horsepower of the power plant are reducing the weight of the carrier and hence the total power required for moving the paying load. Before considering the application of these metals to shipbuilding, it is well to explain some of the fundamentals of ship design.

Jan 1, 1936

By Paul L. Goddard, Alfred G. Hoyl, William R. Sirola

A good place to look for elephants is in elephant country, and old mining districts are certainly elephant country as far as minerals are concerned. In many areas probably more ore is still in the ground than has been taken out. The old timers were good miners and hard workers and when they left ore behind, it was usually for good reason; but many an old mining district has been revived by new approaches to old problems, taking advantage of new techniques and new equipment. One of these is the Front Range mineral belt of Colorado, which has produced minerals for the past 100 years through the ups and downs of mineral prices and the general economy. Gold, silver, copper, lead, and zinc have been found in abundance in the complex sulfide veins of the area. Between Idaho Springs and Central City lie several strong veins which have been mined successfully in the past. The two strongest of these veins, striking northeast-southwest, (Lake-Bald Eagle), and northwest-southeast, (Crown Point-Belman) , and dipping northeast and northwest, respectively, intersect in a flat X near the head of Virginia Canyon. From the lowest drainage of the area, Clear Creek Canyon, the old timers drove the Central, or Big Five, haulage-drainage tunnel due north. It intersects the two veins 8460 ft from the portal and 1670 ft below the surface. The two veins were mined successfully at the surface and at the tunnel level. Without an opening to the surface at the in- side end of the tunnel, ventilating became very difficult as the stopes were opened up, and mining ceased in 1929. Vertically, 1200 to 1600 ft of virgin ground remains in the veins.

Jan 6, 1959

By D. R. Walker, M. C. Shaw

THE laws of comminution of Kick and Rittinger have been debated for many years. Certain data obtained from ball mill and drop tests are found to be in approximate agreement with Rittinger's law while other data would seem to support Kick's law. In all these tests the energy required to produce a wide variety of particle sizes has been studied. Surface area has also been measured with considerable difficulty, at first because it was thought that the energy associated with crushing was that required to create new surface, later because of precedent and because a more fundamental variable was unknown. Tests made with the machine shop type of grinding process show that normally brittle materials that are usually crushed can behave like the more ductile metals. Brittleness is then a relative property largely dependent on specimen size and stress state. The machine grinding operation offers a convenient means for studying the comminution of materials in which the important size variable retains its identity. The energy required to grind a certain volume of material is shown to be strongly de- pendent on size. Kick's law is found to hold very well for particles below 1 micron in size, while Rittinger's law holds approximately in the comminution of larger particles. While a physical origin of Kick's law is established in terms of the theoretical strength of materials having a perfect lattice structure, there is found to be no physical basis for Rittinger's law.

Jan 3, 1954

By Morris Cohen

It has been known for several years that in certain age-hardenable alloys precipitation of finely divided particles occurs simultaneously with the changes in physical properties; while, in other alloys, these changes take place prior to, or without any, precipitation. The silver-copper alloys are generally considered to be the classical example of the first group, and the aluminum-copper alloys (duralumin) are typical of the second group. The two types of aging are explained by the precipilation theory and the knot theory respectively.‡ It is well recognized now that these theories do not conflict with each other; the one used for a given aging system depends upon which way the alloy in question happens to age-harden. However, previous work on the aluminum-copper al1oys1,2 has shown that if the aging temperature is raised sufficiently the hardening will be accompanied by actual precipitation. In fact, it is quite probable that all of the so-called knot-hardening alloys will harden by precipitation at elevated temperatures. Therefore, a combination of the knot and precipitation theories is necessary to give a complete picture of the agehardening of these alloys, and indicates that knot formation and precipitation are not independent processes. To test the generality of this concept, it is necessary to show that the alloys that commonly harden by precipitation will harden prior to precipitation if the aging temperature is sufficiently lowered. For this reason, it would be well to carefully re-examine the aging characteristics of the silver-copper alloys at aging temperatures somewhat below those used by previous investigators. If hardening can be detected prior to precipitation in these alloys, it will lend great weight to the idea that knot forma-

Jan 1, 1937

By H. C. Miller

The energy stored in the compressed natural gas absorbed in or otherwise associated with the oil in reservoir sands is usually the most important factor in oil recovery. It is recognized that hydrostatic pressure and gravity may aid materially in the drainage of oil, but in the early life of the majority of fields the principal source of propulsive energy is the expansive force of the gas associated with the oil. Since gas is admittedly the most important factor in the production of oil, its control so as to produce the maximum amount of oil with the minimum amount of gas will be reflected in increased oil recovery from reservoir sands. Controlling the gas means regulating its expansion so that the velocity of flow of oil through the channels in the reservoir sands is neither so great that frictional resistance becomes excessive nor so slow that the gas, because it can travel more rapidly than oil through the irregular passageways in the sands, will by-pass and reach the well without. doing useful work in bringing oil from the sands. Oil and gas flow from the reservoir sands to the well because of differences in pressure. The rate of flow is dependent upon the differential pressures existing in the sands and in the well. By altering the amount of back-pressure maintained on the well this differential pressure can be regulated and changed from a maximum (well flowing "wide open") to a minimum when there will be no flow. Oil and gas flow through the irregular channels in reservoir sands at different rates mainly because of the fact that one is a liquid and the other a gas. Therefore, because oil and gas have different characteristics of flow, application of back-pressure, changes the rates of flow with relation to one another so that wide variations in gas-oil ratios are possible. Obviously, the formation gas energy will be utilized most efficiently when a unit of gas delivers the maximum amount of oil to the well. Determination of Necessary Back-pressure The amount of back-pressure that should be maintained against the producing sand in order that the minimum amount of gas will be produced with each barrel of oil can be determined only by actual field tests made

Jan 1, 1929

By Fred Allison

THE magneto-optic method of analysis had its origin in experiments1 which were designed to detect and measure a time lag in the Faraday effect and later to study this time lag as a function of the wave length of the light.2 Faraday discovered in 1845 that a beam of plane polarized light, when passed through a transparent, isotropic medium traversed by a magnetic field of force parallel to the direction of the light, suffers a rotation. The direction of rotation is reversed with the reversal of the magnetic field and its magnitude depends upon the strength of the field, the length of the path of light in the substance and the nature of the substance. This phenomenon of magnetic rotation is known as the Faraday effect. A question which had been of some interest for years was whether this power of a liquid to rotate polarized light is acquired instantly with the application of the magnetic field, that is, whether it is a case of instantaneity or whether there is a very small interval of time which intervenes between the application of the magnetic field and the consequent rotation of the light by the liquid; in other words, whether there is a time lag in the Faraday effect. Efforts to measure such a lag previously had met with failure. It was recognized at the outset' that since a time lag had escaped detection it must be extremely small, if to a measurable extent it exists at all. It became necessary therefore to adopt a timing device capable of making measures of almost infinitesimally small intervals. The velocity of light served as this timing device, a modification of a method originally employed by Abraham and Lemoine3 being adapted to the requirements of the problem. Since light travels about 30 cm. in a billionth of a second and since settings in our observations may be repeated with deviations not exceeding 3 mm.,

Jan 1, 1932

The 128th meeting of the American Institute of Mining and Metallurgical Engineers constituted a two weeks trip through the Great Northland of Ontario and Quebec and was a most memorable occasion. The last visit of the Institute to Canada was made in 1907 when the mines, which now have brought world wide fame to some of the camps, were not yet dis-covered. The party reached its greatest numbers at Porcupine where 167 visitors and nearly one hundred local members participated. Five members of the party from the States were on the previous trip in 1907. They were Mr. and Mrs. L. D. Huntoon, John Stevenson and son and E. F. Eurich. The Minister of Mines for the Province of Ontario attached his private car to the "Mining Engineers' Special" and made the complete trip through Ontario. This was a happy incident in many ways and gave the visitors an opportunity to discover a spirit of mutual accord between the Minister and mining industry that might well be emulated elsewhere. Two compartment cars and one standard Pullman with the Institute members from New York and the metropolitan district were attached special to the 6.15 p.m. Lehigh Valley train from New York, Sunday, Aug. 19, en route to Toronto, where was held the first session of the Institute's 128th Meeting.

Jan 9, 1923

By C. R. Barrett, N. N. Singh Deo

The high-temperature steady-state creep behavior of a series of dilute copper-silicon alloys was studied to determine the effect of stacking fault energy on the creep-rate. The steady-state creep rate is, when taken at equivalent diffusivities decreases with decreasing stacking fault energy. The stress and temperature dependencies of is suggest that creep is a difusion controlled dislocation climb process. Electron microscopy studies of the creep substructure revealed: 1) the subgrain size is not a function of the stacking fault energy in these alloys, 2) the dislocation density not attributed to the subgrain walls seems to be higher during primary creep and decreases to a lower steady value during steady-state creep, and 3) the dislocation density during steady-state creep decreases with decreasing stacking fault energy. In the past few years numerous investigators have studied the influence of stacking fault energy on high-temperature creep strength. Most of these investigators have confined their attentions to studying the relationship between steady-state creep rate, is, and stacking fault energy, ?, when samples are tested under conditions of comparable stress and temperature. For the case of fcc metals, it was initially shown by Barrett and Sherbyl and since confirmed by many others2"4 that is decreases with decreasing ?, often following an empirical relation of the form i ?m where m is a constant about equal to 3. The application of theory to explain this observation has not been entirely successful. One of the main difficulties has been the almost complete lack of structural information (dislocation density, subgrain size, and so forth) for samples with different stacking fault energies, tested under high-temperature creep conditions. weertman5 has attempted to explain the stacking fault energy dependence of is on the basis of a dislocation climb mechanism. Assuming that both the rate of dislocation core diffusion and the ease of athermal jog formation decreases as ? decreases Weertman has argued that the rate of dislocation climb and hence the creep rate should also decrease as ? decreases. One questionable aspect of Weertman's analysis is the assumption that core diffusion down extended dislocations is slower than core diffusion down unextended dislocations. The only experimental work done in this area, by Birnbaum et al.6 on nickel and Ni-60 Co, has shown the core diffusivity to increase with decreasing ?. Theories of steady-state creep based on the diffusive motion of jogged screw dislocations often seem unable to predict even the qualitative nature of the es- relationship. Assuming that Weertman is correct in his assumption that the dislocation jog density decreases with decreasing ? then the jogged screw theories predict an increasing dislocation velocity with lower ?. It is usually assumed that the increase in dislocation velocity implies a corresponding increase in creep rate. However, two other factors must be considered before such a statement can be made. That is, we must know how both the mobile dislocation density and the effective stress (the difference between applied stress and internal stress) vary with ?. Significant changes in either one of these factors could outweigh any change in dislocation velocity accompanying a change in ?. And with the slower rates of recovery expected in low stacking fault energy materials it seems likely to expect both mobile dislocation density and effective stress to be dependent on ?. Sherby and Burke7 have suggested that stacking fault energy influences the creep rate in an indirect way. These authors cite evidence that the steady-state subgrain size generated during high-temperature creep is a function of ? decreasing with decreasing ?. Assuming the creep rate to be proportional to the area swept out by each expanding dislocation loop and that subgrain boundaries are good barriers to dislocations, then the creep rate should be proportional to subgrain area, hence increasing as ? increases. A critical evaluation of any of the above theories requires more quantitative information concerning the dislocation substructure generated during high-temperature creep. Accordingly this investigation was undertaken with an aim of studying the influence of stacking fault energy on tbe steady-state creep characteristics of a series of dilute copper-silicon alloys. Special emphasis was placed on studying the strain dependence of both the dislocation configuration and density. MATERIALS AND PROCEDURE Dilute copper-silicon alloys of the compositions shown in Table I were tested in tension at constant stress. The relative stacking fault energy of these alloys has been determined and is shown in Table 11. An Andrade-Chalmers lever arm was used to maintain constant stress and testing was carried out in a water

Jan 1, 1970

By James C. M. Li

The Petch relation between the flow stress and the gain size is derived from a consideration of gain boundary sources of dislocations without the need of dislocation Pile-ups. Three mechanisms for inierpreting the yield stress: the gain boundary strength, the unpinning of Frank-Read source near a grain boundary, and the generation of dislocations from the grain boundary are compared and the condition of their equivalence is shown. The effect of the average angle of misfit of pain boundaries is found to be sma11 and so is that of the average angle of misfit of subboundaries having impurities. The effect of impurities on the ledge density in the grain boundary is treated thermodynamically and a relatwn is proposed for the variation of Petch slope with impurity activity. The effect of temperature on the Petch slope is interpreted as due to the change of ledge structure in the grain boundary. It is indicated that the effect of annealing temperature may be more important than that of the test temperature and therefore should be studied. The effect of plastic strain on the Petch analysis is deduced from a work-hardening equation in which the generation of dislocations has first-order kinetics and the annihilation of dislocations has second-order kinetics. It is concluded that the Petch slope will decrease with plustic strain if the rate of annihilation of dislocations is sufficiently large. Critical experiments which may shed light on the mechanism for the Petch relation are suggested. THE relation between the yield or flow stress, 0, and the grain size, l, was first proposed by all' and later studied more extensively by Petch and co-workers, who also proposed a similar relation for the fracture stress and deduced from these a grain-size effect of the ductile-brittle transition temperature. The microscopic mechanism used by all' and petch2 involves a pile-up of dislocations of like sign generated from a Frank-Read source. The yielding or flow takes place when the pile-up exerts sufficient stress at the grain boundary so that the plastic deformation can propagate from one grain to another. If the average strength of the grain boundary is ai and the average length of the pileup is lp, the Petch slope, k, is given by" where p is the shear modulus, b the Burgers vector, and v the Poisson ratio. This slope will be independent of the grain size if l/lp is a constant. This is possible, since, if the Frank-Reed source is situated near the grain boundary, lp = 1, and if it is situated in the middle of the grain, Ip = 1/2. cottrell,12 also using the pile-up mechanism, proposed that the stress concentration at the grain boundary will initiate Frank-Read sources near the grain boundary and in this manner a Lüders band can propagate from one grain to another. Assuming that the average distance between the Frank-Read sources and the grain boundary is 1, and the unpinning stress of the Frank-Read sources is op, Cottrell obtained the following Petch slope: This slope will be independent of the grain size if ls is independent of the same, which is not as obvious as the condition, Ip = I for Eq. [2]. In addition to this assumption, the direct relation between the Petch slope k and the unpinning stress, up, was recently questioned by Johnsonon grounds that it is inconsistent with the following observations: the independence of k with temperature and strain rate, and the small k in columbium, which, like iron, has a sharp yield point. As pointed out by ohnson," the most important objection both to the Hall-Petch mechanism, in which the strength of the grain boundary plays the role in yielding, and to the Cottrell mechanism, in which the unpinning of Frank-Read sources plays the role in yielding, is the lack of direct observation of the pile-ups. The dislocation structure in deformed iron has been examined recently in the electron microsope.'-' Dislocations appear to be generated from grain boundaries or other interfaces; they form clusters and tangles within the grain at very early stages of deformation, even in the Lüders band, if the deformation is slow or at normal and elevated temperatures. Although it is still too early to interpret bulk properties from thin-film observations, it does seem worthwhile to look for a mechanism for the Petch relation which does not require dislocation pileup. SUBBOUNDARY SOURCES In order to show that a consideration of grain boundary sources can lead to the same Petch relation as does the consideration of the strength of the grain boundary, we shall first discuss the case of a simple tilt boundary whose elastic properties have been studied in detail.17 The strength of a partially

Jan 1, 1963

By D. J. McAdam, G. W. Geil, R. W. Mebs

As shown in previous papers by the authorsg-17t the resistance of a metal to fracture, like its resistance to plastic deformation, is a function of all three principal stresses. A technical cohesion limit is the technically determined resistance to fracture under a specific stress system. The technical cohesive strength thus comprises an infinite number of technical cohesion limits corresponding to the infinite number Of possible com-binations of the principal stresses. The technical cohesive strength, therefore, may be represented by a surface in a diagram with the three principal stresses as coordinates. As shown in previous papers,'-'' the technical cohesive strength increases with plastic deformation, with decrease in temperature, and with increase in the strain rate. The technical cohesion limit, therefore, is affected by the same factors that affect the flow stress,$ namely, the stress system, plastic deformation, temperature, and the strain rate. More- over, the influence of each of these factors on the technical cohesion limit has been shown to be qualitatively similar to the three of the same factor on the flow stress.9-18 Advance of knowledge about the conditions determining fracture of metals has been retarded by the reluctance of some investigators to abandon preconceived ideas about how metals ''should,, behave. The incorrect idea is still prevalent that the conditions determining resistance to fracture are very different from those determining the flow stress. Attempts are still being made to express resistance to fracture in terms of a single parameter, such as a limiting value of the greatest principal stress, the maximum shearing stress, or the volume stress (one-third the algebraic sum of the three principal stresses). In these attempts, a sharp distinction is sometimes made between a ductile or ,plasticdeformation, fracture,, and a "brittle frat-ture.H In making this distinction, however, the meaning attached to the term "brittle fracture" sometimes is not made clear. The term could mean fracture after very little plastic deformation or it could be used to designate the type of fracture. An ordinary fracture of a ductile metal at room temperature starts as a cleavage, generally transverse to the direction of the greatest principal stress, but eventually changes to a shearing fracture' In some conditions, however, the metal fractures entirely by cleavage, with no evidence of plastic deformation during the fracture; the surface of such a fracture may have a

Jan 1, 1948

By R. W. Mebs, G. W. Geil, D. J. McAdam

As shown in previous papers by the authorsg-17t the resistance of a metal to fracture, like its resistance to plastic deformation, is a function of all three principal stresses. A technical cohesion limit is the technically determined resistance to fracture under a specific stress system. The technical cohesive strength thus comprises an infinite number of technical cohesion limits corresponding to the infinite number Of possible com-binations of the principal stresses. The technical cohesive strength, therefore, may be represented by a surface in a diagram with the three principal stresses as coordinates. As shown in previous papers,'-'' the technical cohesive strength increases with plastic deformation, with decrease in temperature, and with increase in the strain rate. The technical cohesion limit, therefore, is affected by the same factors that affect the flow stress,$ namely, the stress system, plastic deformation, temperature, and the strain rate. More- over, the influence of each of these factors on the technical cohesion limit has been shown to be qualitatively similar to the three of the same factor on the flow stress.9-18 Advance of knowledge about the conditions determining fracture of metals has been retarded by the reluctance of some investigators to abandon preconceived ideas about how metals ''should,, behave. The incorrect idea is still prevalent that the conditions determining resistance to fracture are very different from those determining the flow stress. Attempts are still being made to express resistance to fracture in terms of a single parameter, such as a limiting value of the greatest principal stress, the maximum shearing stress, or the volume stress (one-third the algebraic sum of the three principal stresses). In these attempts, a sharp distinction is sometimes made between a ductile or ,plasticdeformation, fracture,, and a "brittle frat-ture.H In making this distinction, however, the meaning attached to the term "brittle fracture" sometimes is not made clear. The term could mean fracture after very little plastic deformation or it could be used to designate the type of fracture. An ordinary fracture of a ductile metal at room temperature starts as a cleavage, generally transverse to the direction of the greatest principal stress, but eventually changes to a shearing fracture' In some conditions, however, the metal fractures entirely by cleavage, with no evidence of plastic deformation during the fracture; the surface of such a fracture may have a

Jan 1, 1948

By Donald Barton

THIS paper outlines a time-saving graphical method of calculation for application to the interpretation of observations with the Eötvös torsion balance. Preliminary to the treatment of this short cut method which has been found practicable, the principal formu-las by which the student of interpretation can calculate the gradient and differential curvature produced by different types of bodies in different types of situa-tions are presented and discussed. It is necessary to split most geologic bodies into a series of simpler ones for which not too complicated formulas are avail-able. The gradient and differential curvature effects are calculated for each of the simple bodies and then summed to the total effect for the whole body. The calculations are considerable in number and, though more tedious than difficult, should be' entrusted to an experienced calculator. Considerable facility in qualitative interpretation can be acquired by the geophysicist from experience and from a thorough study of the types of gradient and differential curvature anomalies produced by the dif-ferent types of possible structural situations. How-ever, semi-quantitative calculations' of the probable structure bring out many relations that are not evident in a simple inspection of torsion balance results ; it throws out as impossible or improbable certain of the alternative structural possibilities that may seem equally probable under simple inspection of the results; it will determine more accurately the position of the crest of the structure; and reduce considerably the un-certainty in the interpretation and it is necessary to intelligent interpretations. The calculation of such cross-sections consists of a trial-and-error calculation of a body that will give gradient and differential curvature effects as closely as possible the same as those observed. From his knowledge of the gradient and differential curvature produced by different types of bodies, the geophysicist sketches a tentative cross-section of the structure as indicated-to him-by the observed results of the torsion balance survey, and the calculator then splits the struc-ture into blocks, and calculates the gradient and differ-ential curvature block by block. If, as rather usual, the calculated .gradient and differential curvature pro-files diverge considerably from, the respective observed ones, it is necessary to add and subtract blocks from the cross-section until a close agreement is obtained .between the calculated and observed profiles. The com-plete calculations have to be gone through for each block that is added or subtracted.

Jan 9, 1928

By Charles E. Wait

HAVING had some experience in the use of gasoline-gas in a laboratory, I have been induced by frequent inquiry to present a few hints concerning it, which I hope may be of some value to those who are out of the reach of coal-gas, and who contemplate using this gas. While I will not delay to describe the method by which this gas is made, it may not be out of place to note that, unless frequent charges are put into the carburetter, the gas is variable in richness. This may be partially avoided, it is said, by repeatedly pumping from one cell in the carburetter to another. If a machine is in constant use for many months without re charging, the gas becomes rather poor for illuminating purposes ; but in this condition it may be burned in a Bunsen burner with advan tage. Could the gas be used always in this condition, no difficulty would be experienced, and it would be quite satisfactory for general laboratory purposes. Considerable annoyance, however, is experi enced whenever the machine is filled with gasoline. The Bunsen and other burners then produce a flame too smoky to be used with com fort, and, in fact, with most of them, a full supply of air; turned on at the base of the burner, will not suffice to completely burn off all the carbon. Finding it necessary to adopt some method by which I could get a flame free from unconsumed carbon, I adopted a plan which has in every way proved satisfactory. In addition to the pipe conveying the gas to the table, and ar ranged with a stopcock, there is brought to the table, within a fern inches of the gas-pipe, another pipe, conveying air direct from the pump. This pipe is also arranged with a stop-cock. The air- and gas-pipes are now connected with one pipe by a T joint; and to this last pipe is attached, by rubber tubing, the Bunsen or other burner. I have successfully used this simple system in connection with both small and large Bunsen burners, a burner with three tubes, arid a Fletcher burner; and recently I have added a new still to our equipment, and have been tising with it a Fletcher special high power burner No. 6, to which this system has been applied. With

Jan 1, 1886

By William E. Hughes, Roderick K. Davey

The objective of this chapter is to review and discuss interpolation techniques commonly in use in the mining Industry today, including simple examples. This chapter will not attempt to compare the relative accuracy of each technique as this subject has adequately been covered by several authors (Knudsen and Kim, 1967; David, 1974; and Barnes, 1979) When appropriate, methods will be compared relative to the results of simple examples and computational ease. The examples presented are based on metallic deposits. The techniques, however, are not restricted to metallic deposits and can generally be applied to nonmetallic ones. The purpose of interpolation, as applied to a mineralized deposit, 1s to extend the knowledge of the grade and geology of localized samples to an estimate of the grade and mineralogy of a larger block of ground or even an entire deposit. The word interpolation means to compute values between given values and is limited to that region between the known values. The distinction between interpolation and extrapolation is important and must be adhered to in the application of these techniques in general, the interpolation must be limited to the area enclosed by verified samples. The methods being discussed can be broadly broken into three categories. ( 1 ) geometrical methods, (2) distance weighting methods, and (3) geostatistical techniques.

Jan 1, 1979

By T. C. Boberg, R. B. Lantz

This paper presents a method for calculating the producing rate of a well as a function of time following steam stimulation. The calculations have proved valuable in both selecting wells for stimulation and in determining optimum treatment sizes. The heat transfer model accounts for cooling of the oil sand by both vertical and radial conduction. Heat losses for any number of productive sands separated by unproductive rock are calculated for the injection. shut-in and production phases of the cycle. The oil rate increase caused by viscosity reduction due to heating is calculated by steady-state radial flow equations. The response of successive cycles of steam injection can also be calculated with this method. Excellent agreement is shown between calculated and actual field results. Also included are the results of several reservoir and process variable studies. The method is best suited for wells producing from a multiplicity of thin sands where the bulk of the stimulated production comes from the unheated reservoir. The flow equations used neglect gravity drainage and saturation changes within the heated region. INTRODUCTION This paper presents a calculation method which can be used to predict the field performance of the cyclic steam stimulation process. The calculation method enables the engineer to select reservoirs that have favorable characteristics for steam stimulation and permits him to determine how much steam must be injected to achieve favorable stimulation. While the calculation represents a considerable simplification of physical reality and the results are subject to numerous assumptions which must be made about the reservoir, it has been found that realistic calculations can be made of individual well performance following steam injection. The duration of the stimulation effect will depend primarily on the rate at which the heated oil sand cools which, in turn, is determined by the rate at which energy is removed from the formation with the produced fluids and conducted from the heated oil sand to unproductive rock. A complete mathematical solution to this problem is a formidable task, and finite difference techniques would undoubtedly have to be used. The calculation method pre- sented here utilizes analytic solutions of simple related heat transfer and fluid flow problems. The method is sufficiently simplified that it can be used as a hand calculation, although the calculations are somewhat lengthy and laborious. For that reason, the analysis was programmed for an IBM 7044 digital computer. Well responses observed at the Quiriquire field in eastern Venezuela&apos; have been matched using this program after making suitable approximations for reservoir and wellbore conditions. One of the most valuable uses of this calculation method is to assess the effect of reservoir and proc-cess variables on the stimulation response. This paper contains results of several studies made of key reservoir and process parameters. Among the most important of these is the influence of prior wellbore permeability damage. If a well is severely damaged prior to stimulation, a higher stimulation response will be observed than if it is undamaged. If a portion of this damage is removed, a permanent rate improvement will occur. THEORY I)ES(:KJJ&apos;TION OF CALCULATION METHOD The process of cyclic steam stimulation is essentially one of reducing oil viscosity around the wellbore by heating for a limited distance out into the formation through the injection of steam. Suitable modifications of the calculation technique presented here can be made so that stimulation of wells by hot gas injection or in situ combustion can also be calculated. A schematic drawing of the heat transfer and fluid flow considerations included in the calculation method is shown in Fig. 1. In brief, the calculation assumes that the oil sand is uniformly and radially invaded by injected steam. For wells producing from several sands, each sand is assumed to be invaded to the same distance radially. In calculating the radius heated rn energy losses from the wellbore and conduction to impermeable rock adjacent to the producing sands are taken into account. After steam injection is stopped, heat conduction continues and oil sands with r < ra cool as previously unheated shale and oil sand at r > r, begin to warm. The effect of warming of oil sand out beyond r, has little effect on the oil production rate compared to the effect of cooling of the oil sand nearer the wellbore than ra. Thus, in computing the oil production rate, an idealized step function temperature distribution in the reservoir is assumed where the original temperature exists for r > rn and where an average elevated temperature exists for r < rn. The average temperature in the oil sand for the region r < rn is computed as a function of

Jan 1, 1967

By Martin A. Mayers

Five-sixths of all the coal that is mined in the United States is burned, without previous treatment other than screening, for the production of heat and power, so that its value is fixed by its suitability for this purpose. Nevertheless, the characteristics of individual coals that determine their fitness for use in particular pieces of combustion equipment are not yet well known. This condition is due not only to the small extent of our knowledge concerning coal itself, but also to our comparative ignorance of the nature of the combustion process. The following paper is an analysis of the combustion process as it occurs in industrial furnaces, based largely on the results of laboratory research on combustion rates. From this analysis it is possible to determine the characteristics of the fuel that limit the capacity of a given piece of combustion equipment. Limitations imposed by other factors than the attainable speed of combustion will not be considered, since they are subject to a different type of analysis involving the balancing of maintenance costs against fixed charges. In order to observe the relations among the various factors that affect the speed of combustion, representative particles of fuel will be followed through two types of furnaces. A pulverized-coal furnace will be considered first, because the independence of the individual particles facilitates the analysis of the effect of furnace conditions. The second example will be a grate-fired furnace in which ignition of the fuel takes place on the underfeed principle. This includes both underfeed and chain grate stokers, (8)† but does not include hand-fired furnaces and some overfeed stokers. The furnace will be considered to be large enough, the temperature high enough, and enough air provided, to burn the fuel completely, without, for the moment, specifying these quantities more completely. Furnaces Burning Pulverized Coal In a pulverized-coal furnace, the fuel particle is carried, in a stream of air, into the furnace, where it is subjected to radiation from the flame and from the hot walls of the furnace. The increase of particle tempera-

Jan 1, 1936

By A. J. Bartlett

Island Creek conditions are generally referred to as ideal; yet, as at all other properties, there are all known hazards of coal mining. The hardest of these hazards to combat is the human element. The basic thought in the minds of the management of these properties is to produce coal with the utmost safety, and it has impressed upon its supervisory force that it does not want a ton of coal unless it can be produced safely. This company has instituted a mine inspection department, which reports direct to the general manager, arid all matters pertaining to safety come under the direction of this department. Through the medium of the inspection department, the management is kept in touch with the actual conditions existing in general at all mines. Inspections are made regularly arid continuously; that is, at all times while the mine!: are in operation some sections of some mines are being examined. These inspections cover all active and inactive workings. Miners are contacted in their working places and other employees at their respective, work. A thorough check is made to see that the state mining laws are complied with and that company safety rules arc being observed. Night shifts receive the same attention as day shifts. All violations and dangerous practices are brought to the attention of the plant supervisory force with suggestions and recommendations; major hazards of emergency nature are taken up immediately with the management. Periodical inspections are also made of all tipples, preparation plants, dumping and hoisting equipment, to see that all machinery is properly guarded, and walkways and platforms properly fenced; conditions of equipmcnt and mechanical defects are also reported. Reports of inspection are written in letter form and in such a manner as to give the management a picture of the existing conditions at the time of inspection. Copies of inspection reports are forwarded to the superintendents with the general manager&apos;? comments. It has been said, "There is nothing under God&apos;s heaven that justifies. your creation or your citizenship but this gospel: &apos; That the next greatest

Jan 1, 1938

By A. C. Richardson

Troughs or launders are probably the oldest machines used for ore concentration, and their development was suggested no doubt by the natural segregation and stratification of materials that take place in the bed of a stream. Trough washers for coal cleaning were first used in France and Germany about one hundred years ago and have been used in some form or other ever since. The early launders were intermittent or batch machines, and only comparatively recent developments have made them continuous. The chief disadvantage of early launder systems as applied to coal has been that when a satisfactorily clean coal was produced the loss of good coal in the refuse was excessive. Other disadvantages have been the large quantities of water and the great lengths of troughs necessary to treat moderate tonnages of feed. One of the most widely used types of trough washers is the Rheolaveur, which has been developed in the last 25 years. Fig. 1 shows a more or less standard arrangement for fine coal. In this there are four trouglis placed one below the other and sloped a few degrees from the horizontal. Rheo-boxes or draws are provided at intervals in the bottom of the trough for the removal of material deposited from the stream. These draws are spaced substantial distances apart. Some of the rheo-boxes are provided with upward currents of water to modify the horizontal current stratification. In operation it is the function of the first two troughs to remove all refuse material and permit only clean coal to be discharged over the end. In order to accomplish this, large quantities of coal are drawn through the rheo-boxes. The third and fourth troughs are used to recover the coal discharged through the boxes of the first two troughs as a middling product and to discharge a clean refuse. The middlings are returned to the first launder and are usually about equal to 40 per cent of the raw coal being fed to the launder. In considering launder processes, one would reason that the conditions of extreme crowding under which stratification takes place in a flowing stream should effect complete separation in a single pass down a launder.

Jan 1, 1938

By Raymond Wilson

Grinding costs are an important item in cement manufacture, and the cost of power is one of the large items in grinding costs. Even where power is of secondary importance, cost items dependent on mill capacity are influenced by the efficiency with which the mill uses power. Tube mills typify the grinding mills most generally used in cement plants, though other types are in use. Tube mills have been widely criticized as being extremely inefficient, and this feeling regarding them has led to many attempts to design more efficient grinding equipment. Other types may be an improvement over tube mills, but the improvement has certainly not been revolutionatry, at least as applied to clinker grinding. The very fact that there is doubt regarding the relative efficacy of various types of mills is an indication that an adequate basis for an analysis of performance is lacking. The development of methods of analyzing mill performance has been hampered by the lack of a suitable method for measuring the work actually done in pulverizing. There has been no acceptable standard to which mill performance might be compared. As a consequence, it was not known whether the margin of possible improvement in pulverizing operations was large or small. Even direct comparison of different types of mills was seldom possible because most plants had only one type of mill for each type of service. Comparisons between plants were difficult because of differences in the grinding characteristics of various clinkers. Some recent developments complete a chain of circumstances that place the cement industry in a particularly fortunate position for the study of its clinker-pulverizing operations. Modern investigators of grinding phenomena have generally agreed that the best measure of mill performance is the production of new surface. For most materials this measure of performance is largely theoretical and has a rather remote connection with the practical aims of the grinding operation. In clinker grinding, on the other hand, surface area is intimately connected with the properties conferred on the cement by grinding. Morcover, the determination of surface area is rapidly coming into routine use as a tost

Jan 1, 1938

By M. King Hubert

The growth of human knowledge is an evolutionary process. Historically our separate sciences came into existence as people became interested in various apparently unrelated domains of phenomena, and in this manner we acquired the sciences of physics, chemistry, astronomy, biology and geology. As various of these sciences became established, cognizance of them came to be taken by the universities and in this manner there arose the traditional departments of physics, astronomy, chemistry, biology and geology of our American universities. As there was no particular rationality in the boundaries separating the various sciences, in the university departments the jurisdiction of each has assumed quite arbitrary limits. In the domain of earth phenomena the first science to grow up was that of geology, which arose originally from the activities of the collectors of rocks, minerals and fossils. Thus geology evolved as a descriptive science dealing with directly observable terrestrial phenomena for which elementary rational explanations were offered. The traditional treatment of phenomena by the science of geology has rarely been with more than an elementary regard for the fact that these phenomena were also phenomena of physics and chemistry. Since the latter part of the nineteenth century, a new approach to terrestrial phenomena has been emerging and becoming of so great a significance that it can no longer be ignored. This approach has been made by people trained primarily in the sciences of physics and chemistry, who have investigated terrestrial phenomena as constituting phenomena of their respective sciences. In this manner we have acquired the so-called "borderland sciences" of geophysics, the physics of the earth, and of geochemistry, the chemistry of the earth. Neither of these fields is new, having arisen chiefly at the hands of European investigators during the latter part of the nineteenth century. The European universities have long since given official recognition at least to geophysics, by the establishment of departments or institutes of geophysics, which are on a par with the university departments of the other sciences.

Jan 1, 1940