Search Documents

Jan 1, 1891

By E. P. Mathewson

THE experiments described in this paper were made at the Washoe Reduction Works, Anaconda, Mont., for the purpose of determining the relative speed of elimination of the iron, sulphur and arsenic during the process of bessemerizing copper-mattes. The samples were taken from a horizontal "barrel" converter, 8 ft. in diameter and 12 ft. 6 in. long, having an average charge of 9 tons of matte, and blown with a 16-1b. air-pressure. All samples were taken with the blast on, turning the converter from its normal blowing-position to nearly verti¬cal, so that a conical mold, with a long handle attached to a horizontal rod, could be introduced from a platform above the converter into the mouth of the converter and a sample taken. The difficulties of taking a sample with the blast on are appar¬ent, and the irregularities of the lines in Figs. 1, 2 and 3 can be readily accounted for by the amount of slag in the samples. On the whole, the plotting of the results gives comparatively uniform lines, considering the conditions. The samples were taken by the regular sampling-force of the works at 10-min. intervals, as shown in Tables I., II and III, which also give the chemical analysis of the samples so taken. The test shown in Table I. was made with a new converter; that of Table II with a converter that had made three charges and had been cleaned out; that of Table III with a converter that bad blown one charge to white metal, and had then been " washed " out and used for the test. In plotting these results, it was necessary to take, as a basis, the percentage of copper in the samples. This basis does not exactly represent the true condition, since the volume is constantly decreasing and a certain quantity of copper passes into the slag, but it is as near as can be obtained in practice. Take, for instance, in Table I., the sample No. 5, which shows : Cu, 59.9;

Jan 1, 1907

By L. D. Clark

Pay-out, the ratio of capital expenditure to annual cash return can be very revealing when employed to gage the merits of a proposed mining venture. It is a quantity, numerically but not physically equal to a factor, by which cash return may be discounted to equal required investment. The fewer the pay-out years, the greater the average annual earning power of the project. Considerable material has been written in the past about the most important and difficult problem mining management faces in evaluation of a property: the optimum production rate for the venture. What daily capacity should be adopted for the proposed operation that it may be the most rewarding to those underwriting it? H.C. Hoover has said, "The most important objective is the least cost per ton mined; and minimum working costs can only be gained by the most intensive production." Theoretically and practically, the quicker the ore is removed, the more profitable should be the venture because of the saving in fixed charges, the consequent lower unit costs and the interest unearned by the profit from the unmined ore. Yet, such performance will be tempered by policy and a restraint imposed by the ratio of capital expenditure to annual cash return. * The 'Annual net profit after taxes but including depreciation and depletion allowances. former will be based upon an analysis of the economic climate anticipated, with its many ramifications including the demand for the product, prices, tax laws, the conduct of labor and related wage scales. The variables and intangibles involved in estimating the optimum production rate for a mine do not readily lend themselves to mathematical relationships or equations and the problem can become complex indeed. The more readily applicable and relatively faster appraisal method will be used which, in addition to being reasonably adequate in most cases, will serve as a guide, should a more expanded and detailed estimate be desired. The first question is what is company policy with respect to the rate of investment return? This will depend on that significant period of time referred to as the pay-out, which can be defined as the estimated interval during which capital investment is returned through application of annual cash return to its recovery. Expressed another way, it is the ratio of capital expenditure to the annual cash return. For example, if the capital investment is $C and the annual cash return is $A (after Federal tax), then $C/$A = the pay-out period in years. That is to say, if $C = $1,500,000 and $A = $214,000, then which is the mathematical expression for the period of time it takes to recover the funds originally invested in a mining enterprise. The relationship yp = $C/$A can be useful — an expression which requires only the significant tern yp to be fixed; in other words, the long range investment policy. For what is the pay-out period but an expression of that policy in terms of the speed, within practical limits, with which an individual or company may want to recover capital expenditure? A policy by which pay-out will be fixed is imperative. This ratio must lie within relatively narrow limits governed by what is economically feasible. It cannot be too low, rendering the ratio impractical or absurd, nor too great, delaying the return of capital for reinvestment beyond a commensurate interval. What pay-out will govern this policy? Federal corporate taxes would seem to present the best measure. Consider mining in Canada where new mines are exempt from Federal income tax for 3½ yr from date of first production. This exemption expressly allows The Act states: "A corporation . . . i s not required to include the profits . . . for the period of 36 months commencing with the day on which the mine came into production in reasonable commercial quantites." a company to recover capital expenditure during the early stages of production. With such an incentive, it is logical to strive for as much capital redemption as possible during this period. Thus, 3½ yr would be a major contribution to the pay-out in Canada. Furthermore, it generally takes from 1½ to 3 yr to develop

Jan 1, 1963

By M. Metzger, T. A. Read

The strengthening effects of hydroxide and synthetic plastic films in the creep of cadmium crystals were studied. The results were broadly consistent with the naive mechanical model. The dislocation-film reactions and the significance of the macroscopic stresses associated with certain films are discussed in the paper. ALTHOUGH a number of studies have been made of the strengthening of metal single crystals produced by surface films usually less than Ir in thickness, the mechanisms underlying this phenomenon are still not well established. Roscoe' first noted the critical shear stress and the stress-strain curve of cadmium-crystal wires to be raised markedly by the presence of oxide films. Subsequent investigators2-' have confirmed the effect for several metals and films including a number of plated poly-crystalline metal films. Harper and Cottrel1" with a thin film on zinc presumed to have formed as a result of etching and washing treatments) did not detect a strengthening at a rate of extension of 10 ' sec-' although at lo-' sec-' the film raised the flow stress by 7 pct at 0.0005 extension and by 22 pct at 0.01. The marked strengthening at moderate strains thus appeared to be the result of a dynamical effect dependent on the rate and amount of plastic flow. Other observations'. " are consistent with this view. The large effects of films on the tensile creep rate of single crystals were demonstrated when the observation of Andrade and Randall," that the creep rate of cadmium crystals increased on immersion in aaueous solutions of certain cadmium salts. was shown' * to hold only when a film was present initially and was explained by the attack of the solution on the film and the removal of its strengthening effect. Changes in the creep rate interpretable in terms of the removal or formation of various films have been observed by other investigators.3,8,10,31 Certain other experiments have been reported in which surface films or liquid environments have affected the plastic behavior of metals, but these are not within the scope of the present work which deals with the effect of solid films on single-crystal slip. Possible Mechanisms—The film does not significantly reduce the load on the crystal in the elastic range (the elastic moduli of film and crystal are not too greatly different and the area of the film is so small that its share of the load is negligible) so that the initial operation of internal Frank-Read sources is not affected. However, as Fisher" has pointed out, a source terminating on the crystal surface requires only half the critical stress for activation as an internal source of the same length and a relatively strong film (even a very thin one) would pin the free ends of the surface sources so that, if surface sources are responsible for plastic flow in a clean crystal. such a film would increase by roughly a factor of 2 the stress necessary for generation of dislocation loops at a given rate. The other general possibility is that the film resists the passage to the crystal surface of internally generated dislocations. If the film is adherent and if the specimen is to exhibit slip of the same general character as a film-free specimen, the film must deform or fail in shear at the active slip planes. The naive mechanical model, where shear-stress relaxation across the active slip plane in the metal transfers load to the film until it deforms and slip can

Jan 1, 1959

By G. Pizzi, G. M. Ciucci, G. L. Chierici

The use of the material balance equation to estimate the volume of hydrocarbons originally present in a reservoir, whose producing mechanism is partly due to water drive, has been discussed in the literature by several authors. There is no general agreement upon the possibility of obtaining reliable results by this method. Gas reservoirs in contact with an active aquifer are considered in this paper. Theoretical considerations based on the cybernetic principle of uncertainty (which states that the internal structure of a system cannot be uniquely determined from its observed external behavior) lead to the conclusion that the volume of gas originally present in a reservoir of this type cannot be uniquely determined from its past history. The range of values which encompasses the actual value of the reserves varies from case to case and must be determined by either numerical or analogical methods. Results obtained for six gas fields are reported. All these fields were produced with small fluctuations in their production rates, as is common practice for gas reservoirs; no gas storage fields were considered. Results obtained show that reserves values in a range of 1 to 2, associated with appropriate aquifers, allow the matching of the reservoir past history with mean-square deviations less than the experimental errors involved in pressure and produclion measurements. Similar results have been found in several other partial water drive gas reservoirs. From these results it is concluded that gas reserves cannot be uniquely determined from the past performance of partial water drive reservoirs, at least in cases where the reservoir has been submitted to small fluctuations in the production rates, and pressure data of normal accuracy are available. INTRODUCTION A number of authors have analyzed the problem of estimating the reserves originally present in a partial water drive reservoir from its past pressure-production performance. Literature which deals with this subject can be grouped, according to their conclusions, as follows. 1. A reliable value for the reserves can be obtained even if reservoir data (pressure and cumulative production) are affected by errors within the normal range.'-' 2. A reliable value for the reserves can be obtained only if reservoir data are very accurate'- or if past production performance has been subjected to abrupt variations in the production rate."' 3. No unique value for the reserves can be obtained from reservoir past production performance. This conclusion has been based upon theoretical considerations" and verified in several field cases. The purpose of this paper, which deals only with partial water drive gas reservoirs, is to test the above conclusions against actual field cases. Some theoretical considerations on this problem are also presented. THEORETICAL CONSIDERATIONS As the behavior of a gas reservoir communicating with an aquifer depends on both the aquifer and the reservoir characteristics, the physical system to be studied is the combined gas reservoir plus aquifer. The information which is available for studying the performance of such a system is the well production rates and bottom-hole pressures, all given as functions of time. The external behavior of the reservoir-aquifer system is therefore described by 2n input variables (Gp, Wp,) and n output variables (p,), n being the number of wells in the reservoir. In reservoir engineering it is common practice to consider the reservoir as a whole, disregarding the internal distribution of pressures and of producing wells. This practice is equivalent to substituting the above multi-variable system with a single-variable system, where the average reservoir pressure is the only output variable and the cumulative production G,(t) and W,(t) are the input variables. The internal structure of such a system, defined by initial gas reserves G, aquifer shape and dimensions, boundary conditions and petrophysical parameters distribution throughout the aquifer, is unknown. Therefore, from a cybernetic point of view the system is a "black-box It has been demonstrated" that for a blackbox the indetermination principle holds. Accordingly, the number of different internal structures (or set of parameters) which can account for the observed external behavior is infinite. As a consequence, the initial reserves cannot be uniquely determined from the reservoir past performance. When W,(t) is known, the determination of G from

By N. M. Langdon

The calculation of slags may be considered under three cases: I. A certain percentage of silica is required, it being known, in a

Jan 1, 1893

By F. D. Rosenthal, F. J. Dunkerley, G. J. Mills

Activities, free energies, and heats and entropies of mixing of liquid Pb-Zn alloys have been obtained by the electrode-potential method between 400° and 650°C. The large positive deviations observed from Raoult's law are in agreement with the phase diagram, which indicates a wide immiscibility field. A vapor-pressure method was used to extend the activity measurements to 900°C, allowing the maximum of the immiscibility gap to be estimated by thermodynamic calculation. Data on the mono-tectic and eutectic points compare favorably with previously existing work. SEVERAL long-standing methods have been in use for the study of phase diagrams from measurement of the activities of the component metals.' The use of thermodynamic analysis for interpreting equilibria data is comparatively recent, however. Such analysis is usually undertaken by first evaluating the principal thermodynamic functions as, for example, the enthalpy, entropy, and free energy of the alloy constituents. These, in turn, quite often can be correlated with the interatomic potential energies and atomistics of the system, from which a clearer understanding of the causes leading to deviations from ideal behavior is gained. The present study of liquid Pb-Zn alloys is concerned with a determination of these quantities by electrode-potential and vapor-pressure measurements, using these values in calculations involving phase equilibria and to obtain a theoretical insight into an alloy system exhibiting strong positive deviations from ideal metallic solution. A considerable portion of the previously reported work is based on thermal analysis. Supplemented by optical studies of solid alloys, these techniques have revealed the essential nature of the immiscible mixtures that are formed. It is difficult, however, using the phase-

Jan 1, 1959

By L. W. Emery

Undergrorlnd combustion operations were initiated in a 60-acre Bartlesville sand "shoe-string" reservoir in Allen Connty, Kans., in 1956. Tests in separate patterns were conducted using various co~nbinations of air and recycle gas to propagate combustion fronts from the injection toward the producing wells. These patterns were made up of 6 injection and 20 prodrrcing wells Gas and liquid prorluctiorz from each pattern was measured on an individual-well basis, and comparisons were made between the three patterns to ascertain the relative effects of injected gas composition on production behavior. Breakthrough of the combustion front at a well was characterized by an increase in water production from the well followed by an increase in bottomhole temperatrrre to approximately 250" F. After burning fronts had broken through at five producing wells, operations were terminated in 1960. From the total project approximately 79,000 bbl of oil were produced during thermal operations at a cumulative produced GOR of 23 Mcf/bbl. No appreciable change in the character of the produced crude was observed. Combustion in the reservoir was maintained with injected gas compositions ranging fronz 6 per cent oxygen in recycle gas to 100 per cent air. lnjectiotz of large quantities of recycle gas resulted in higher producing GOR's from offset wells than were measured from a pattern into ~vhich straight air ~vas injected. The air required to move the combustion front through I acre-ft of reservoir was computed to be 20 MMscf. This valrre was found to be relatively independent of the quantities of recycle gas injected. The recovery efficiency from the swept area was esti~izated to be about 59 per cent. Areas swept were similar in shape to tlzose obtained with a laboratory potentiometric model. Samples of sund taken from behind the burning front by coring indicated almost total oil removal from the sand. Petrographic analysis of the core samples indicated that the sand had been heated to peuk temperature of rlbout 1,200" F. No rignificant difference in peak temperature was forrnd in two areas where compositions of injected gas were quite different. Compression costs for thermal recovery were estimated to be $1,20/bhl of produced oil. INTRODUCTION The use of the "forward combustion" process as an oil recovery method has received a great deal of attention. This method involves ignition of the formation in an injection well, followed by propagation of a combustion front through the reservoir. Combustion is maintained by the injection of an oxygen-containing gas to react with reservoir hydrocarbons. As the flame front progresses through the reservoir, oil and formation water are vaporized, driven forward in the gaseous phase and recondensed in the cooler part of the formation. In turn, the condensed fluids push oil into the producing wellbores. Completed field tests of the process were first reported by Kuhn and Koch,' and by Grant and Szasz.' Results from other tests have since been reported by Walter,3 by Moss, White and McNeil,' and by Gates and Ramey." ach of these tests essentially utilized a single injection well surrounded by four or more producing wells. Sinclair Research, Inc., elected to do field experimental work using a number of test patterns in a single field in order that comparisons between various operating schemes could be made. The site selected and purchased in 1955 for this experimental work was a 60-acre Bartlesville sand reservoir located in Allen County, Kans. Combustion operations were initiated in mid-1956. Between that time and termination of the project in mid-1960, combustion fronts were propagated from injection wells to producers in three separate well patterns, using different mixtures of air and recycle gas. The test was terminated before sweep of the three patterns was complete so that information about the effect of combustion on the swept areas could be obtained by coring. Results from the test in the form of injection and producing well performance have been carefully recorded, and these form the general basis for this paper. DESCRIPTION OF RESERVOIR The reservoir in which the combustion tests were conducted is a Bartlesville sand "shoe-string", typical of a number of small reservoirs in Southeastern Kansas. Average reservoir characteristics are shown in Table 1. Fig. 1 is an isopachous map of the producing sand showing the reservoir to be approximately 400-ft wide and 2,500-ft long. Maximum net productive sand thickness is 21 ft. Fig. 2 shows a typical core analysis obtained by coring with water-base mud. The reservoir has no appreciable dip and is closed on the sides by degradation of sand into shale. The main body of sand is heavily laminated with shale stringers, which are not continuous between wells. The main reservoir is overlain by 30 to 40 ft of laminated low-permeability sand and shale streaks. No information is available on the original properties of

The Committee on Nominations will welcome from members of the Institute suggestions for the offices which are to be filled by election in February, 1018, and which are as follows: One officer, known as Director and President. Two officers, known as Director and Vice-President. Five officers, known as Director. The attention of members is called to Articles V and. VII of the Constitution, and to By-Law VIII, which reads as follows: "The geographical districts to he considered by the Committee on Nominations shall be as follows, until otherwise ordered by the Board.

Jan 8, 1917

By S. W. Kennedy, M. Cohen, L. D. Calvert

A high-temperature X-ray diffraction method has been used to study the composition and the kinetics of formation of oxide scales at 800 °C on iron and pure iron-nickel alloys containing 25.6, 75, and 84 pct Ni. This technique has been combined with chemical analysis, and metallographic examination, and determination of weight-gain time curves. The 75 and 84 pct Ni alloys form a three-layer scale consisting of porous NiO next to the metal, a spinel layer, and a -Fe203 on the outside. The 25 pct Ni alloy produces a scale of spinel and Fe,O,, in which, however, traces of FeO and NiO are observed near to the metal. On all the nickel alloys the Fe20, is orieqted with the (107) plane parallel to the surfaces. The exposed surface of the Fe20, is in the form of needles whose axis is perpendicular to the specimen surface. Although the alloys show nonuniform oxidation rates as determined from weight-gain measurements, the X-ray data indicate that the total scale and individml scale layers grow uniformly and parabolically. Deep subscale formation is observed in the 25 pct Ni alloy only. This appeared to be associated with cracking of the scale and penetration of the oxygen along the grain boundaries. ALTHOUGH film formation has been investigated by high-temperature electron-diffraction techniques, for example by Gulbransenl and Hickman,' there have apparently been no investigations of scaling by methods permitting study of the scale during formation at the reaction temperature. Methods involving quenching of scales are based on the working assumption that no significant changes take place on cooling. In general, however, compounds may disproportionate, and the different thermal expansions of constituents may cause disruption of the scale on cooling. In particular, some scales cannot be quenched without spalling. These difficulties are avoided by X-ray diffraction examination at the temperature of formation. High-temperature diffraction procedures also provide a method of determining the kinetics of formation of each phase separately in a multicom-ponent scale. The scaling of binary iron-nickel alloys Containing up to 30 pct Ni at a temperature of 800°C has been studied by Benard and Moreau using cooled specimen~,~ whilst Foley, Druck, and Fryxel14 made an electron-diffraction study of cooled oxide films formed on an iron 42 pci Ni alloy. In the present work the scaling of three iron-nickel alloys containing 25.6, 75, and 84 pct by weight of nickel, at 800°C in oxygen at atmospheric pressure was investigated by X-ray diffraction techniques using a Norelco Geiger-counter diffrac-tometer. The oxidation of iron was investigated for comparison. In addition normal metallographic examinations and chemical and X-ray analyses were made, and weight-gain time curves obtained. EXPERIMENTAL Materials Used—The analyses of the alloys were as follows: Percent by Weight Nickel 25.6 pct 75.4 pct 83.2 pct Aluminum 0.004 None found 0.002 Cobalt — 0.05 0.05 Chromium — — — Silicon — 0.01 None found Carbon All less than 0.05 pct The chemical analysis of the iron was: Al— 0.002 i 0.001 pct, C—0.007 pct, Cr less than 0.001 pct, Cu—0.002 ± 0.001 pct, Mn—0.003 ± 0.001 pct, N—0.0002 pct, 0-0.013 pct, P—less than 0.0002 pct, Pb—not detected, S—0.0017 pct, Si—0.0095 pct, Sn—none detected. This iron was the same as that used to make the alloys and was obtained from the same source-Vacuum Metals Corp. One specimen of pure iron from The British Iron and Steel Research Association was used for preliminary investigation. Specimens were machined to shape from cast rod, polished (the final polish being with 600 Sic paper), degreased in trichlorethylene, washed, and etched. The etching and neutralizing procedure adopted by

Jan 1, 1960

By J. S. Mitchell

Cobalt recovery from arsenical concentrates by pressure leaching and reduction involves special methods and operating problems. Principal steps in the process are auto-oxidation acid leaching under pressure, filtration of the tailings, purification of the solution, hydrogen reduction of the ammoniacal solution, and electrical furnacing for sulfur removal and granulating the metal. Extracting cobalt metal from arsenical ores has presented a major metallurgical problem for many years. In acquiring the Blackbird mine near Salmon City, Idaho in 1943 Calera Mining Co. accepted the challenge to solve this problem.

Nov 1, 1956

By D. H. R. Price

This paper presents two tentative models of the use of a notional metal in a country like Britian, which have been developed using the System Dynamics modelling method. Computer simulations have been carried out using one of the models. These show the effect on the recycling of the notional metal of a wide range of possible future values of world market price and demand for the metal.

Jan 1, 1977

Speech advocating a new law of the sea-the "common heritage of mankind." The 3rd Law of the Sea (L0S) Conference was held in Caracas in mid-1974, and a fourth UN conference, scheduled for mid-March in Geneva, will once again attempt to produce a cohesive LOS Convention to take up where the 1958 Geneva Convention left off. The 1958 Convention specified coastal state resource rights on a continental shelf out to a water depth of 200 m-a supposed technological limitation at the time. But the surge of offshore petroleum drilling and the advent of the nodule resource have long since exploded beyond the 200-m limit.

Jan 4, 1975

By H. M. Rutherford

THE reflection method in seismic prospecting has aroused much interest in the past few years. The purpose of the present paper is .to present the method of reflections in the mapping of geologic structure and also to give some indication of its limitations. The reflection method is well adapted to the mapping of geologic structure in the Mid-Continent fields, and has been found most useful there. The refraction method is ideally suited to the finding of structures, such as domes, where the amount of relief is very large. This explains the brilliant success of the refraction method in the Gulf Coastal region of Texas and Louisiana. The additional fact that salt has a much higher velocity than the sur-rounding sediments made their discovery much easier. By the use of the reflection method, differences of relief of 25 to 50 ft. to the mile may be detected at a depth of 5000 ft., and the depth points accurately plotted on a map. This is hardly possible by the use of the refraction method. The reflection method has been in almost continuous use in the Mid-Continent area since 1926, but very little, if anything, has been published until recently(7) ? regarding either the method or the results. The dis-covery of several oil fields is now attributed to the use of the reflec-tion method. Reflection methods have been used by the Germans to find the thick-ness of the ice of several glaciers. (2,8) The depths there considered were of the order of only a few hundred feet. For the method to be of any practical value in this country, it must be able to work to depths of several thousand feet. As was indicated above, this is now possible, though there are many problems connected with the reflection method yet to be solved. The refraction method requires that the shooting be done over long ranges. It was necessary, for example, to take distances out to several miles in order to penetrate some five thousand feet. Naturally this uses a good deal of dynamite. In the reflection method the distances are much shorter and the amounts of dynamite are much smaller, within limits which will be noted below. The chief distinction between refrac-tion and reflection methods is to be found in the analysis of the seismo-gram. Refraction shooting makes use of only the first arrival of energy

Jan 1, 1932

By F. W. Gordon

THE Whitwell firebrick hot-blast stove, for furnace use, may be seen in its three, main stages of development in the accompanying drawings. Fig. 1 is the stove of 1869, the, year in which it was thoroughly tested at the Consett furnaces, England; Fig. 2, the stove of 1876 and 1877, in which it was intended to reduce the-cost by increasing the height; Fig. 3, the stove of 1880. Many modifications were made from time to time, generally in the direction of improvement, but the drawings illustrate the main features of progress. In the stove of 1869 the plan was to introduce the gas at A, and pass it up and down. between each alternate wall, the air in the reverse direction, passing in at B. The friction in this stove was so great, owing to the. restricted area of the passages and the many reversals of the gaseous current, that it was deemed imprudent to build the stoves higher than 28' 6'". Another reason was that the great importance of cleaning was carefully kept in view, and it was very difficult to operate any hand scraper even to this depth. For these reasons the 22' X 28 1/2' stove held the field for several years. A slight change made from this was to the 18' X 40' stove, where the height was increased, but the number of walls diminished. In this stove the friction was somewhat reduced, but so was the heating surface, and although it cost a little less it was not any better. The next important change, seen in Fig. 2, was by increasing the height to 60 feet and keeping the full number of walls in the stove. The heating surface and mass were much increased in proportion to the cost, and the friction decreased by alternating over and under two or more walls, instead of one, as formerly. This stove gave admirable satisfaction, but; although the proper doors were provided, it was very difficult to clean, owing to the long distance the scrapers had to traverse. Stove No. 3 is a modification of No. 2. The great question was how to decrease the cost without impairing in any yaw the

Jan 1, 1881

By S. Stutz

Coal, like most other minerals, only exceptionally occurs in a sufficiently pare state to he directly available for general manufacturing purposes. And even where this is the case, the small coal or slack is usually more impure than the lump coal, as the slate, clay, etc., from the roof and bottom of the vein become mixed with it in the handling it undergoes. These impurities often exceed ten or more per cent. in addition to the impurities of the coal itself. The most common impurities of the coal are slate, or shale, clay, and sulphur. The latter occurs in different forms, but moat frequently as bisulphide of iron, or iron pyrites, and as sulphate of lime, or gypum. In both cases the impnrities add greatly to the amount of ash, and where they are present in considerable quantities the raw coal, and still more the coke made from it, is unfit for the manufacture of iron. Coke will coutain on an average at least fifty per cent. more ash and sulphur than the ram coal from which it is made. To the manufacturer of iron every additional per cent. of ash which his coal or coke contains is a source of additional expense, seemingly small, and yet very important in the aggregate. In the blast-furnace, for instance, the ash must be heated up to the melting-point, and, since it is composed largely of refractory substances, the consumption of carbon in melting it will be equal to at least one-half of its weight; that is, a certain part of tile coke is consumed for the melting and fluxing of the ash and is lost. Besides this, it is well enough known to the iron-master that coke containing lees ash makes the &lag or cinder more liquid and less incliner1 to stick to the walls of the furnace. Fuel containing much sulphur produces generally a white iron, poor in carbon, while from the same ore arrd flux, with a pure fuel, a good foundry iron might be obtained. The work of separating slate, sulphur, etd, from the coal has as yet only been successfully accomplished by the washing process. This process depends for its success on the differences in the specific

Jan 1, 1881

By Harrison, Henry Fay

The study of an entirely new series of alloys may be undertaken from a desire to obtain knowledge applicable to the perfection of industrial alloys, or merely to test certain theoretical considerations. In the case of antimony-tellurium alloys, the theoretical side only is at present important; but it is hoped that the results of this investigation may have some industrial value, at least indirectly, by furnishing one more example for comparison when studying commercial alloys. The statement is found in various places that antimony is isomorphous with arsenic, bismuth and tellurium; but very little experimental evidence has been offered in support of this assumption. All four metals crystallize in rhombohedra, and the ratio of the axes a: c is approximately the same—which seems to indicate, but does not prove, their isomorphism. The close association of these metals in minerals also seems to indicate that they are isomorphous. There are, however, certain differences in their properties which render this coriclusion somewhat doubtful, and it is therefore desirable that inde-

Jan 1, 1902

By E. E. Donath

THE coal hydrogenation process is well known as a means for the production of liquid fuels -from coal. In this paper the possibilities of the coal hydrogenation process as a source of chemical raw materials will be discussed. The recovery of chemicals from coal hydrogenation products necessitates some modifications and additions to the equipment used for the production of fuels. The conversion of coal into liquid fuels such as gasoline requires two steps: liquid phase and vapor phase hydrogenation. Intermediate oils obtained in the liquid phase contain oxygen and nitrogen compounds, especially aromatic compounds, since the coal itself is composed mainly of cyclic compounds. These oils are the raw material for the separation of high molecular weight aromatics and of tar acids and tar bases. The relative amounts of heavy and middle oil-boiling above and below, e.g., 325°C-can be influenced by temperature, residence time, and catalyst of the liquid phase hydrogenation. In the vapor phase hydrogenation a solid bed catalyst is used to convert the intermediate oil from the liquid phase operation into hydrocarbons of the gasoline boiling range. Essentially pure hydrocarbons with a low content of sulphur, oxygen, nitrogen, and olefines are obtained. Depending mainly on the catalyst, the high ring compound content of the liquid phase oil can be preserved and gasoline rich in aromatics obtained. However, with other catalysts, these ring compounds can be split into gasoline with a high content of isoparaffins.1 Again, depending on the operating conditions, products of varying boiling range can be obtained. Selection of catalyst and operating conditions therefore makes possible the production of different grades of motor fuel and also variations in the relative amounts of benzene, toluene, and xylene when aromatic hydrocarbons are produced. The schematic flowsheet, Fig. 1, shows the main steps of the coal hydrogenation process, and the product streams used for the recovery of chemicals are indicated. In the liquid phase hydrogenation stage, coal is made into a paste with recycle heavy oil. The coal paste is mixed with hydrogen and preheated at a pressure of 300 to 700 atm in heat exchangers and preheaters. The coal paste and hydro¬gen enter high pressure converters where the liquefaction of coal, conversion of the high boiling liquid materials initially obtained, into intermediate oils is performed at a temperature around 470°C. The reaction products enter the hot catchpot in which lower boiling oil vapors are separated from the residue containing unreacted coal, ash, and heavy oil. This residue, usually called H.O.L.D. (heavy oil let down), is processed to separate solid and liquid material. By thermal treatment of the residue, e.g., a coking process, distillate oil is obtained, which can be recycled as part of the pasting oil. This stream is rich in polynuclear aromatics and can be, and has been, used for the recovery of such material. The oil vapors and hydrogen from the hot catch-pot are cooled in heat exchangers and a cooler, and the condensed oil is separated from the recycle hy-

Jan 1, 1952

By E. C. Wright

THE following article is based on observation of college graduates entering the steel industry in technical work made during the past 25 years, the first five of which were spent as a college instructor in two engineering schools, and the last 20 in the employ of a large steel company that has hired hundreds of engineering graduates for steel-mill operations. The college graduates encountered during this period have come from many, colleges representing schools in Eastern States, Midwestern Universities, many Southern colleges, and many smaller colleges and normal training schools mostly in western Pennsylvania and Ohio. The college training of these students for engineering work naturally has varied widely and the educational qualifications of the entrants have been in many ways different. It was found at an early date that graduates of standard engineering colleges were much more adaptable than graduates in science from nontechnical schools. The engineering students seemed to be more suited to actual work in steel' plants and in general were better able to grasp a knowledge of the operations they observed. However, although the graduates of engineering schools have had somewhat better training -in physics, mathematics, and engineering, it has been a general and continual observation that most of the students employed have had inadequate training in the fundamental sciences. Since this discussion relates entirely to metallurgical engineers, it should be emphasized that students taking metallurgical engineering courses in college seem to be poorly trained in organic chemistry, physics, physical chemistry, thermodynamics, and any higher form of mathematics than simple calculus. It has been noted frequently that young engineers faced with problems in a mill that involve some mathematics generally flounder badly, and that they have little conception of physical chemistry. Another common deficiency lies in the young graduate's lack of knowledge of where to look for the more detailed literature on any subject. He reverts instinctively to some college textbook whose coverage is usually very elementary. It is recommended that such textbooks contain a bibliography of the source literature, and that students be taught to use theoriginal data. Many of the students had had previous courses in college dealing with metallurgical work such as steel melting, metallography, etc., but it was found that their grasp of these subjects was extremely sketchy. It was soon realized that an ordinary engineering graduate could be taught more about steel melting and manufacturing processes in a, few weeks in a. plant than he could learn in a college course on such subjects. A similar statement may be made regarding the ability of students to conduct laboratory work. Their lack of technique and skill in handling equipment and setting up experiments was soon apparent. It became neces-

Jan 1, 1946

By I. Fatt

Study of a model which contains "dead-end" pore volume indicates that pressure transients are influenced by the amount of dead-end pore volume and by the resistance of the flow path between the dead-end pore volume and the main flow channels. A semi-empirical method is demonstrated that makes possible measurenment of the volume in the dead-end pores and the total pore volume. The difference between these two volumes is the volume of the flow channels. An indication of the flow resistance between the dead-end pore space and the lain flow channels is also obtained. INTRODUCTION In some engineering calculations the distribution of pore volume in a petroleum reservoir need not be known. For example, a material balance calculation treats a reservoir as an oil-filled tank. In other calculations the distribution of pore volume appears implicitly through use of the porosity and the relative permeability and capillary pressure characteristics. It is the purpose of this paper to point out that under certain conditions the exact distribution of pore volume must be known in order to interpret correctly transient flow behavior. Pressure transients during single-phase flow in porous media are usually said to obey differential equations of the form