Search Documents

By F. J. Schuh

The drilling industry long has been plagued by failures in the bottom few joints of surface and intermediate casing strings. This paper presents an analysis of the various possible causes of failure and concludes that failures are caused by short-lived, high-energy torque impulses delivered from the drill string through the bit while drilling out the cementing plugs, cement and floating equipment. The magnitude of these torque impulses is shown to be a function of the rotational momentum of the drill string, and a method is derived to calculate the magnitude of these impulses. The available methods of strengthening the bottom joints are reviewed. It is concluded that, while present methods are ineffective, a combination of improved procedures for strengthening and minor restrictions on drillout practices will prevent failures. Introduction In most cases, failure in the bottom few joints of casing strings is not discovered until electric logs record that the bottom one, two or three joints have parted from the casing string and slipped down the hole. However, in some cases the parted section of casing uncovers a high-pressure or lost circulation zone, or shifts laterally restricting the passage of drilling equipment. In these instances extensive remedial work is required to realign the parted pieces and seal the exposed formations. Several methods used to strengthen the bottom joints of casing strings include locking set screws in the couplings, putting wedges in special collars, welding straps across the couplings, welding the couplings and, most recently, using epoxy resin-based, thread-locking compounds. Since none of these techniques has eliminated the problem, this study was initiated to find the cause of failures and to evaluate the available methods of prevention. Mechanics of Casing Failures An analysis of the various possible causes of failure indicates that the casing is unscrewed rather than broken and that therefore failure must occur before the shoe is drilled. Since there is no general agreement as to the causes of casing failure, some possible mechanisms were ATLANTIC RICHFIELD CO. DALLAS, TEX. considered in this analysis. Failure of the bottom joints of casing can occur by only one of three types of stress: tension, torsion or bending. The possible mechanisms of failure were evaluated by determining the forces required to cause casing failure by each of the stresses; and, where applicable, the possibility of failure by fatigue was considered. For casing to part under tension requires a downward load of more than the tensile strength of the casing. The lightest API weight H-40 grade casing requires a bit load on the bottom of the casing of 27,000 to 34,000 Ib per inch of bit diameter (Table 1). Since maximum drill collar weights seldom exceed 10,000 Ib per inch of bit diameter, it is apparent that casing strings cannot be parted by the downward load of the drill string. The second mechanism considered was failure by bending. This mechanism requires that the lowermost casing joints be free to be deflected laterally until the bending stress exceeds the strength of the pipe. To fail, the casing (at a height L above the shoe) requires a force and deflection' at the shoe of To deflect the casing shoe with the drill string obviously requires a dog-leg at the casing shoe. This dog-leg must have a rate of change equal to or greater than the change in curvature of the deflected casing, which is given by

Jan 1, 1969

By Foster Fraas

That variations in the humidity of the air and in the moisture content of a mixture of broken solids being separated electrostatically cause trouble is not new.' Much of the reputation for unreliability commonly ascribed to the electrostatic separation processes is probably due to this one factor alone. Some operators dry thoroughly before separating; and while this is good in many instances, there are others in which it is not the remedy for trouble. Some mixtures behave best in very dry air and with the mixtures fed to the separator while hot to reduce the adsorbed water content. On the other hand, an overdried mixture on coming to equilibrium with more humid air, has been known to take up moisture selectively on one family of particles, as of coal in the presence of slate and clay, and give sharper electrostatic separation. From these observations it is concluded that there is a permissible moisture content for a particle and also for the atmosphere surrounding it, if in equilibrium, at which the particle will have a conductivity or cntact potential2-4 that is ideal for electrostatic separation. This permissible moisture content varies between a wide range of limits for the different materials that are are and with the kind of electrostatic separating process used. Water can be present as a result of adsorption and condensation from the atmosphere, as an accumulation before or during mining, or as a residue from a previous process step. The water may exist as a liquid film or as an adsorbed layer of vapor. If the water exceeds permissible limits it must be removed. Its state determines the method. Drying by evaporation is necessary for adsorbed water, for part of the liquid-film water (that is, up to several percent of the dry weight), and for free water in the internal structure. Large water contents may be removed by drainage Or filtration. At just what point mechanical removal should cease and drying by evaporation begin depends upon the method of mechanical removal and its cost. Particles can also be separated according to their differences in dielectric constant when suspended in a liquid of intermediate dielectric constant. Recovery of this liquid presents a a problem' Permissible Moisture The adsorbed moisture on the outer surface of minerals can be quickly removed or replaced. Accordingly, in speaking of adsorbed moisture contents, either that of the solid or that of the surrounding air may be considered, the two values being connected by a distribution coefficient which varies with the temperature. However, such a condition does not necessarily exist in processes where an initially dry material is suddenly introduced into an atmosphere having a partial pressure of water vapor or where a moist material is suddenly introduced into a dry atmosphere. Here the resultant differences in the

Jan 1, 1949

By Waldemar Lindgren

At the time of the discovery of America the old world had a scant supply of the precious metals. Both the northern and the southern part of the new continent proved wonderfully rich in gold and silver and its treasures were eagerly looted; though the looting has lasted four centuries, the mines of its mountain chains are far from being exhausted. Even the later discoveries in Australasia and eastern Siberia could not rob the Western Hemisphere of its position as the greatest gold and silver producing region of the world, though finally the developments in a narrow and circumscribed area in South Africa wrested from the Americas their supremacy in the production of gold. Nevertheless the history of the two parts of the great western continent has been strikingly different. At first the Spaniards extracted vast treasures of silver from Mexico, Peru, and Bolivia, while Colombia arid some placer deposits in Peru yielded a smaller quantity of gold. A couple of centuries later, a stream of gold began to flow from Brazil, the silver production from the countries mentioned above continuing strong in the meanwhile. Later on, the yield of South America diminished, but to offset this there began a wonderful series of discoveries in North America. The gold fields of California astonished the world; and when the cream of these had been skimmed off there began a no less amazing development of the Central Cordilleran gold and silver districts, which soon made the United States the greatest producer of the precious metals. Aided by ever improving technique, extensive exploration, and a system of railroads, the yield was maintained and increased. Still later followed the discoveries of the gold fields of the arctic region and silenced those who had maintained that the zenith in gold production had passed. Recently the province of Ontario in eastern Canada

Jan 1, 1917

By H. W. Gillett

WE hear much in these days about "tailor-made" steels. Farseeing executives have sensed the demand for metals of improved and special properties, with those properties deliberately built into the steel in order to fit it for a particular use or group of uses. They have set their metal-lurgists at work to produce what the customer needs, even though the tonnage required may not, at least at first, be great. As the metal-lurgists bring out such metals, the products are advertised and the customer becomes increasingly conscious that he no longer has to take "ready-made" steel as the only thing available, whether it fits his needs or not, but that there are plenty of steelmakers ready to serve his specific needs with a tailor-made steel. Of course this is nothing new in the realm of rather highly alloyed steels to be heat-treated. The automotive industry demanded and got such steels long ago. Indeed, one could not design a modern car using only non-heat-treated carbon steel, since an engine of present horsepower would be so heavy that the gasoline required merely to lug the engine itself around would be absurd. Many different alloy steels and many different heat-treatments are required to produce the fine gradations of properties and the strength per unit weight that are needed in each particular part. Aircraft designers, of course, count a high strength-weight ratio in the materials used as Article I in their constitution, and they too, and in outstanding degree, require tailor-made alloys. Aircraft and automobiles may be considered as the tail coats and Tuxes of the metallurgical tailors. Nowadays there is also a demand for business suits, in the form of high-strength alloys to reduce dead load and so increase payload, all through the transportation industry. We hear most about weight-saving design and materials in respect to the railroads, with the spectacular new high-speed passenger trains and the prosaic freight car. The latter sounds especially sweet to steel-mill ears, because it means tonnage. While most of us think of these developments, and of the engineering acceptance of high-strength materials as "new," the fundamentals are of almost hoary antiquity. It is the widespread availability of a variety of materials and their general acceptance that are new.

Jan 1, 1936

By Dwight Farnham

Description of Quarry THE shale used at the Renton plant of the Denny-Renton Clay Coal Co., for the manufacture of vitrified paving brick occurs in a hill rising from 200 to 300 ft. above the level of the valley in which the plant is situated. The shale deposit, which is of unknown thickness pitches about 10° to the southeast. The 150-ft. face worked extends approximately east and west, so that the clip, as shown by the photograph, is to the left and into the hill. The shale is overlain with about 50 ft. of gravel, 70 ft. of clay, and 30 ft. of mixed loam and gravel, making altogether from 125 to 150 ft. of overburden. Disposal of Overburden The overburden is removed by sluicing. For this purpose a No. 2 Joshua Hendy giant is used, throwing a 12-in. stream', and having 60 lb. pressure at the nozzle. The water is drawn through an 8-in. pipe from Cedar river, about 1,000 ft. distant, by means of a Worthington four-stage centrifugal pump, direct connected with a 100-h.p. motor placed just south of the factory, and 1,500 ft. from the nozzle This plant handles the material satisfactorily to a height of about 75 ft. above the level of the top of the shale. When the higher levels are worked, an auxiliary plant consisting of a four-stage Byron Jackson centrifugal pump with a 100-h.p., belt-connected motor, is thrown into the system. This plant is situated on top of the shale and can be discerned at the extreme right of the trestle work in Fig. 1.

Jan 9, 1914

By Hans Von Höfer

Apart from the hypothesis of a cosmic origin (which failed of acceptance because it was not adequately supported by facts), the only important controversy concerning the origin of petroleum has been, for a long time, between the advocates of inorganic and of organic origin respectively. Each of these theories has had a long history of development, and is still being perfected, under the influence of two causes: (1) the increasingly extensive and thorough study of the oil-fields (of which new examples are periodically discovered and opened); and (2) the progress of synthetic experiments devoted to this question. Moreover, the advance in our physical and chemical knowledge of the properties of this peculiar natural product has necessarily modified all criticism of conflicting views. I. The Hypothesis of Inorganic Origin That the nation of an inorganic origin of petroleum, first set forth by Berthelot in 1866, and afterward ingeniously developed and formulated by Mendelejeff, should thus have proceeded chiefly from chemists, is quite natural; for the question was one of possible chemical processes in the earth's interior, and of imagined chemical reactions to be verified by ex-periment. Hypotheses of this kind were suggested by many chemists, of whom two, P. Sabatier and J. H. Senderens, may be specially named by reason of their highly interesting chemical experiments. Among geologists, Mendelejeff's hypothesis was received at first with much interest and favor; for it rested on the assumption of a central terrestrial mass of iron carbide, and the geologists had good reasons for adopting that assumption. Yet comparatively few of them attempted to furnish geological proofs of the hypothesis: the majority either silently believed in it, or for one or another reason rejected it altogether. An apparently weighty support of Mendelejeff's view was furnished by the American, G. F. Becker, who found in the oil-regions of the United States important and abnormal disturbances of the isogons of terrestrial magnetism, and inferred that in these regions the central iron mass must

Jan 1, 1915

By G. Derge, M. Bourgon, G. M. Pound

A STUDY of electrical conductance in molten Cu-Fe sulfide mattes' has shown that pure molten Cu,S behaves like a semi-conductor in that it is an electronic conductor and its specific conductance, of the order of 100 ohm-' cm-', increases with increase in temperature. On the other hand, pure molten FeS, another electronic conductor, behaves like a metallic conductor in that its specific conductance, about 1500 ohm-' cm-', decreases with increase in temperature. Molten solutions of Cu,S and FeS follow a roughly additive rule of mixtures with respect to both specific conductance and temperature coefficient. The behavior of molten Cu,S may be understood, by analogy to the situation in solids, in terms of semiconductor theory.' It is thought that, although the melt consists of cuprous and sulfide ions, the bond between these atoms has a certain degree of cova-lency. According to the simplest concept the electrons in the partially covalent bonds are thermally promoted to a conduction band. In another concept, small amounts of impurities (undetermined) provide donor or acceptor levels in the forbidden zone between the valence and conduction bands and thus facilitate semi-conduction in the usual way. However, the metallic behavior of molten FeS is difficult to explain, because one might expect from similar reasoning that it too should act like a semi-conductor. It was suggested that the apparent metallic behavior of molten FeS might be explained by a large negative temperature coefficient of density. Thus if molar conductance instead of specific conductance were plotted versus temperature, the slope might prove to be positive, indicating semi-conduction instead of apparent metallic conduction. Accordingly, density measurements were made in order to answer this question in regard to molten FeS and also to provide data for conversion of specific conductance to molar conductance for molten Cu,S and a molten 50-50 wt pct Cu-Fe sulfide matte. Experimental Diagrams of the apparatus are given in Figs. 1 and 2. A 3 x 8-cm dense alundum crucible containing the prefused specimen is positioned in the uniform temperature zone of an induction furnace tube and melted under a helium atmosphere. Then the cell assembly, consisting of two 3-mm spectro-graphite rods, one of which is in a 1-cm ID open

Jan 1, 1959

By G. W. Healy, D. C. Hilty

MAJOR considerations in the production of stainless steel are the utilization of stainless steel scrap and the recovery of chromium and other metallic values from the initial furnace charge. The decarburization of a bath of molten chromium steel with gaseous oxygen is usually accompanied by a considerable amount of metallic oxidation. Since recovery of this metal from the slag may require substantial expenditures of time and materials for slag reduction, holding metallic oxidation to the minimum consistent with good operating practice is generally desirable. The important role of temperature in minimizing metallic oxidation is illustrated by Fig. 1, taken from the results of Hilty, Healy, and Crafts,' who established the quantitative relations connecting the amounts of chromium, manganese, and iron oxidized during the oxidizing period of chromium steel heats with the composition of the initial charge and the temperature and composition of the molten bath after oxidation. Higher temperatures after the oxygen blow result in lower metallic oxidation. Although high temperatures are desirable for minimizing metallic oxidation, practical operating considerations limit the degree to which they can be employed. Excessively high temperatures or prolonged operation at moderately high temperatures may cause serious damage to the furnace refractories, so that a compromise must be effected. The problem, therefore, is one of controlling the oxidizing period of chromium steel heats to the shortest time at the highest practical temperature. The most effective tool the steel melter has for attaining high temperature while decarburizing a chromium steel heat is now commonly considered to be the oxygen lance with an adequate supply of gaseous oxygen. In order for the tool to be effective, however, the heat resulting from the oxidation of carbon, chromium, silicon, manganese, and iron in the bath must exceed the heat losses from the furnace. General recognition, of this principle has stimulated a trend toward faster injection of oxygen. For example, Pachaly2 proposed a high temperature at the start of the oxygen blow or a high rate of oxygen input as a means of obtaining the desired carbon level with high chromium recovery. On the other hand, limited understanding of the specific effects of oxygen input rate has hampered development of optimum practices. As part of a broad study of the metallurgy of chromium steel melting, therefore, the Linde Air Products Co. and the Electro Metallurgical Co. at their Metals Research Labo-ratories have evaluated the heat-balance during the oxidizing period in terms of oxygen input rate. The evaluation has then been related to factors such as temperature increase, metallic oxidation, oxygen Utilization, etc., and extrapolated to include a wide

Jan 1, 1958

By G. L. Boxer, C. B. Smith, W. J. Atkinson

Since the inception of the Ashton (formerly Kalumburu) Joint Venture in 1972 the parties have expended $24 million in exploration for diamonds in the Kimberley region. This has resulted in the discovery of the currently subeconomic Ellendale deposits in 1976/77 and the economic Argyle - Smoke Creek Deposits in 1979/80. In addition to Argyle and Ellendale, some 90 kimberlitic and lamproitic bodies have been discovered grouped broadly into three provinces, on the west, east and north margins of the Kimberley block. These bodies range in size from dyke-like features less than 1 m (3 ft) in width to pipes with a surface area of 128 ha (316 acres). The bodies with larger surface area are volcanic crater deposits, infilled with air-fall and water deposited tuffs and epiclastic sediments. Diamond content ranges from trace to economic concentrations. The exploration discoveries were facilitated by early recognition that the petrography, mineralogy and chemistry of the diatremes varied from the classical kimberlites of Kimberley, South Africa, to unusual more highly fractionated, alkaline, silicic varieties having affinities with leucite-lamproite. Indirect methods of exploration were used, primary reconnaissance work being stream gravel sampling for kimberlitic indicator minerals. Evaluation showed Ellendale diamonds are 90% gem and near gem, but the low grades and tonnage render the deposits unpayable at today's diamond prices. After discovery in late 1979 and completion of a feasibility study by the end of 1982, evaluation studies proved Argyle to be economic. Alluvial diamond mining commenced in 1983 producing 6.2 million carats (Mct) that year, 60% being of industrial quality. Open-pit mining of the AK1 lamproite should start in 198511986 at a rate of 3 million t/a (33 million stpy) and produce 25 Mct/a, making this mine, and Australia, the world's largest producer of diamonds by weight. The revenue from diamond deposits is a function of the grade and the value of the diamonds. The grade is the product of the frequency of occurrence of the diamonds (stone density) and the mean stone size; the value of the stones is strongly related to their size distribution. During evaluation of the West Australian deposits, the diamond distribution was found to vary markedly in stone density and stone size. These variations corresponded with changes in the rock type hosting the mineralization. As a consequence, geological mapping of individual lamproites within the multiple vents and careful monitoring of the diamond distribution became an important part of the evaluation work. Similar variations in stone size and frequency were found to accord with separate alluvial terraces and fan gravels derived by erosion from the Argyle AK1 lamproite.

Jan 1, 1985

In 1820, the Board of Public Works was considering some improvements to the canal, in order to reduce the cost of transportation, and in its annual report for that year gives a description of the method of loading the coal from the pit to the boat, and also from the boat to the dealer's yard, which is illuminating in showing how coal of this type should not be handled. It follows:- "It will be seen by the estimates, that the improving the present canal, forming a canal of large dimensions, from the head of the present lower canal to Sabbot Island; erecting locks of large capacity, and making a communication with the river, so as to completely accommodate the coal trade, (except it should hereafter be found necessary to make another communication with the river,) will not cost more than 126,000 dollars. But as there is some doubt whether the streams that may be received into the canal between Sabbot Island and the upper arch, will at all times be competent to supply the locks on that portion, we will extend our calculation to a point nearly half a mile above Pleasants' Island; where, by erecting a dam, any desired quantity may be thrown into the canal. This extension of the canal with one lock, and the dam across the river, is estimated at 34,000 dollars, making in the whole a little over 160,000 dollars. There will then remain a surplus of 40,000 dollars after completing the works to the point last mentioned. "In order to discover what effect the improvement of this first section will have on the tolls, it will be necessary to take a view of the present state of the coal trade, and endeavor to ascertain what change will result from the increased facility of transportation. "That part of the business which is carried on by water, is conducted nearly in this way. When the coal is drawn out of the mines, it is thrown in a heap near the mouth of the mine, or shaft; it is then loaded into carts, and carried to the river bank, where, in some instances, it is discharged from the cart at the brow of the bank, and runs down to the beach near the water's edge; then shovelled into wheel-barrows, and wheeled aboard of the boat, and discharged from the barrows by upsetting. In other instances, the carts are driven on to a kind of scaffold, furnished with a wide spout or director at the edge; by which the coal is conveyed immediately into the boats. These boats are the common James river poplar batteaux, and require three men to each. The up-stream navigation being laborious, the boats are built of light materials, and continue fit for service but a short time, (say) from two to three years; their cost, when new, from fifty to one hundred dollars. "When the river is tolerably flush of water, one of these boats will carry about two hundred bushels; but in low water their load is sometimes diminished to one hundred, and even as low as eighty bushels. They pay for passing the canals and locks to the Basin, one dollar per load; so that when full loads are taken, it will amount to half a

Jan 1, 1942

By D. O. Hobson, P. L. Rittenhouse

We have recently found that many lots of Zircaloy-2 and -4 tubing tested in tension deform to cross section shapes that are "polyhedral" rather than circular. The noncircular cross sections seem to result from a circumferential variation in plastic proper -ties and, therefore, in texture. We examined the diffracted X-ray intensity from (OOOl), {1010), {ll20}, and {1011} planes parallel to the tubing surface around the entire circumference. Tubing that deformed to a circular cross section showed <5 pct variation in diffraction intensity around the circumference from any of these planes. Greater intensity variations were found for all the tubing materials that developed non-circular cross sections during deformation. In each instance the number of intensity maxima and minima was consistent with the number of sides of the &apos;polyhedral" cross section. THE effects of crystallographic texture on the mechanical properties of zirconium, zirconium alloys, and other anisotropic hexagonal materials such as titanium and hafnium have been intensively studied. If the natural crystallographic anisotropy of these materials could be controlled by selected fabrication operations, a material could be produced with a texture, or preferred orientation, in which the maximum strength directions are in the stress directions of the structure. The permissible stress levels of the structure could then be increased. Rittenhouse and Pickle-simerl have shown that highly textured Zircaloy-2 plate can vary from 52,000 to 70,000 psi in tensile yield and from 62,700 to 122,000 psi in compressive yield strengths as a function of specimen orientation. Similar texture effects have been observed in Zircaloy tubing, whose mechanical properties differ depending upon whether the tubing has basal poles predominantly radial or tangential and upon the mode of testing. These same texture effects might be troublesome if the texture in the tubing is not uniform around the tube walls. This paper is concerned with the effects of nonuniform texture on the strain behavior of commercial Zircaloy tubing. BACKGROUND Previously, various lots of commercial Zircaloy tubing were tested under selected stress conditions as part of a program to determine the four quadrants of the yield locus. One of the testing procedures was uniaxial tension and it is the influence of texture variations on the tensile deformation behavior of the tubing that is of interest here. The effect of texture on the strain behavior in tubing is very apparent from a uni-axial tensile test.2 This behavior is illustrated schematically in Fig. 1 for three different tubing textures: 1) basal poles predominantly in the radial direction; 2) basal poles predominantly in the tangential direction, and 3) basal poles equally distributed between the radial and tangential directions. In the first example most of the grains are oriented for prism slip to operate to allow axial lengthening and diametral reduction of the tube. Reduction in wall thickness requires {1122} twinning, a more difficult operation than slip.* In the second example, the texture is such that *The singleCrystal analogy will be used quite often in this paper when strong texturesare being discussed. The textured material is assumed to react as if it were a single crystal aligned in the same orientation and under the same stress system as the predominant texture._____________________________________________ prism slip operates to give axial lengthening and wall thinning. Diametral reduction requires twinning and again should be more difficult to accomplish. A specimen with basal poles equally distributed between the radial and tangential directions should exhibit about equal diametral and wall strains.* Table I shows the *Diametral strain is accomplished by a combination of circumferential and longitudinal strains. But, for the purposes of this paper, it will be considered as a strain causing a change in the length of a specified diameter.__________ strain behavior of two lots of tubing with different textures. The first tube has a texture with basal poles equally distributed between the radial and the tangential directions. The ratio of true thickness strain to true diametral strain is almost unity. The second tube has a predominantly radial basal pole texture and it is apparent that most of the total strain has occurred by diameter reduction, just as one would predict. There is over three times as much diametral strain as thickness strain. RESULTS We found that specimens from certain lots of commercially fabricated tubing did not retain round cross sections during uniaxial testing. Instead, the speci-

Jan 1, 1970

By W. R. Hansen, F. W. Boulger

Twenty-nine laboratory steels were studied to determine the effects of composition and ferrite grain size on drop-weight and Charpy V-notch transition temperatures. The experimental steels covered the following ranges in composition.. 0.10 to 0.32 pct C, 0.30 to 1.31 pct Mn, 0.02 to 0.43 pct Si, md nil to 0.136 pct acid-soluble Al. Although most of the data were obtained on hot-rolled samples, some plates were heat-treated in order to cover a wider range in ferrite grain size. The experimental data were used for a multiple-correlation analysis conducted with the aid of an electronic computer. The study showed that carbon raises and that manganese, silicon, aluminum, and finer ferrite grains lower both drop-weight and Charpy transition temperatures. Quantitatively, variations in composition and grain size have a more marked effect on V15 Charpy transition temperatures than on the drop-weight transition temperature. Useful correlations were found between transition temperatures in drop-weight tests and those defined by seven different criteria for Charpy tests. Evidence was accumulated that the conditions ordinarily used for drop-weight tests are more severe for 1-1/4-in. -thick plate than for 5/8- to 1-in. -thickplate. PROJECT SR-151, to study quantitatively the effects of metallurgical variables on performance in the drop-weight test, was established by the Ship Structure Committee late in 1958 on recommendation of the National Academy of Sciences, National Research Council. This project was initiated as a result of the increasing use of the drop-weight (nil-ductility) test in predicting the ductile-to-brittle behavior of steel. Qualitative data indicated the drop-weight was not as sensitive to metallurgical variables as the Charpy V-notch test. Furthermore, the available information indicated that the drop-weight test did not show the superiority of killed steels over semikilled steels reflected by Charpy tests. This difference in sensitivity to brittle fracture is considered important because the drop-weight transition temperature has been reported1 to correlate better with service-temperature failures than the V-notch test does at a constant energy level. Therefore, this project was concerned with establishing quantitatively the effects of metallurgical variables in the drop-weight test. For comparison, Charpy V-notch data were obtained for the steels investigated. This paper summarizes the results of the investigation. Most of the steels used for the study were made and processed in the laboratory. However, some tests were also made on commercial killed steels available from Project SR-139 (SSC-141). During the course of the investigation, data were obtained on the effects of carbon, silicon, manganese, and aluminum on transition temperatures of drop-weight and Charpy specimens. In addition, the effects of heat treatment which changed the ferrite grain size and the transition temperatures were also investigated. Finally a few exploratory studies were made on commercial killed steels to evaluate the effects of plate thickness, grain size, and heat treatment on the performance of drop-weight specimens. EXPERIMENTAL PROCEDURES Preparation of Materials. A total of twenty-nine 500-lb induction-furnace heats were made and processed in the laboratory for the investigation. Carbon, manganese, silicon, and aluminum contents were systematically varied. Melting and rolling techniques proven satisfactory in a previous project2 were used as a guide for the current investigation. Composition. The composition of the twenty-nine laboratory heats made for this project are given in Table I. The steels are divided into three groups. The first group consists of ten aluminum-killed steels similar in composition to Class C ship-plate steel. The second group consists of ten semikilled or Class B type steels. In both of these groups the carbon and manganese contents were intentionally varied over a wide range. This wide range in composition was helpful in obtaining quantitative data from a limited number of steels. The primary purposes of these two groups of steels was to determine the effects of carbon, manganese, and deoxidation practice. In addition, one steel in each group (Steels 2-2 and 9-2) were made about 1 year after the start of the program in order to check consistency of melting practice. The third group of nine steels listed in Table I was intended for studies on the effects of silicon and aluminum. In eight of these steels carbon and manganese were held relatively constant at levels of about 0.2 and 0.8 pct, respectively, while silicon and

Jan 1, 1963

Energy conservation has been the keyword in many plant expansions. Far many years, most of the phosphate industry has been dry grinding their phosphate rock. Agrico Chemical in Florida has recently been evaluating the wet grinding of phosphate rock, a process which eliminates a pre-dry stage for mill feed while allowing higher through- puts. This same company also plans to open a new phosphate facility in Louisiana that will use wet grinding in both ball mills. The Eveleth Expansion Co.&apos;s Fairlane concentrator will have the largest rod and ball mills in the US mining industry. The plant will consist of three lines, each with one rod mill and one ball mill, and will process 464 ltph. The rod mills will be 15 x 20% ft, drawing 2035 hp. The ball mills will be 17 x 41½ ft, drawing 6900 hp and driven by dual 3000- hp motors. The plant is scheduled for startup in the fall of 1976.

Jan 2, 1975

William B. Phillips, Birmingham, Ala.: The questions raised by Messrs. Wilkens and Nitze are in the highest degree interesting to owners of low-grade iron-ores, aizd no less so to blast-furnace managers. If it can be shown that ores heretofore considered worthless can be brought within the limit of economic use, many large and readily accessible deposits may come into market on the one hand, while on the other the possible increase in the output of the furnace per ton of ore used will prove of advantage to the iron-maker. It cannot, of course, be claimed that this process has been employed on a working-scale with respect to iron-ores, and in so far as concerns results on a large scale no one is any wiser than his fellow. Granting that the results obtained in an experimental way (and certainly the experiments were conducted with a great deal of care) can be attained in practice, we would still be facing the question, what it would cost to get them. In the absence of any specific data, we have to fall back on general principles, helped along, as far as possible, by indications afforded by the experiments. I must confess that as regards the Clinton ores, which I have studied to some extent, I am not sanguine of making a ton of 53 to 54 per cent. concentrates from less than 1.75 tons of 40 per cent. raw ore. It may be possible to get the iron in the heads to 56 to 57 per cent., but the lesser richness of the middlings will probably reduce this to 53 to 54 per cent. in the salable stuff. As the authors remark, it is not worth while to discuss the concentration of the better grades of " soft" Clinton ore; for the price at which they are now delivered at the furnaces, and the comparatively limited amount now remaining, render their concentration unadvisable. If it is to succeed in the Birmingham district, the process must be applied to the low-grade soft and hard ores now con-

Jan 1, 1897

By P. J. Connors, William J. McCormick, F. B. Olender, Jerome F. Sheldon, Donald T. Mylar, Edgar T. Gregory, Owen S. Roberts, H. Colijn

A quiet revolution has taken place in the conveyor belt industry. Man-made materials, improved production facilities, better splicing techniques and emphasis on repair and maintenance have all contributed substantially to lowering material handling costs for the mining industry. Formerly the rubber industry had only cotton for a belt carcass and tree grown rubber for the protective cover. Monofilament rayon, with desirable elongation and elastic properties, was the first synthetic fiber to be used in place of cotton. But wet strength and other limitations restricted its use, and the conveyor belt industry turned to nylon.

Jan 3, 1972

By G. P. Conard, E. H. Rennhack

The creep behavior of hot-rolled, hypoeutectic Zn-Ti alloys was investigated in the temperature range from 0.43 to 0.53 TM. Secondary flow was found to originate primarily from strain-induced gvain growth where grain boundary )nigvation served to relieve the strain energy of distortion introduced by slip, grain boundary sliding, and subgvain formation. The extent to which this recovery mechanism operated was determined by the ratio of grain width to the spacing between planar fibers of TiZn,, compound particles generated in these alloys during rolling. When this ratio was unity, creep resistance demonstrated a marked improvement. In this condition, which was fulfilled by annealing following rolling, structural stability was enhanced with decreasing grain size below the equicohesive temperature (-0.5Tm), while the reverse was true above this temperature. TITANIUM concentrations approaching the eutectic composition of 0.23 wt pctl have been shown to promote a significant increase in the creep resistance of rolled zinc,2 The alloying effect created with titanium is somewhat unique; a structure closely resembling that of a fiber-reinforced metal composite can be developed which selectively modifies creep strength in preference to other mechanical properties. In an earlier investigation,~ the present authors found that, while the fiber network, composed of individual TiZn,, compound particles, had a distinct influence on rolled texture, the crystallographic variations produced were of minor importance with respect to creep. Rather, creep resistance seemingly increased when the grain size appeared to coincide with the in-terfiber spacing. The work described here was undertaken to explore this effect in greater detail. EXPERIMENTAL PROCEDURE Three zinc-base alloys containing 0.05, 0.12, and 0.16 wt pct Ti were prepared from CP zinc and iodide titanium in the form of 4 by 2 by f in. chill-cast ingots. The melting and casting procedures for these alloys have been detailed el~ewhere.~ Individual ingots of each alloy were hot-rolled at 200°C (392°F) to total reductions of 10, 25, 50, 75, and 90 pct in from one to five passes, respectively, employing a 10-min reheat prior to each rolling pass. With grain, tensile-type creep specimens with a 1-in.-long, -in.-wide gage section were machined from the rolled strips for test purposes. Annealing studies to explore the influence of grain size on secondary creep flow were carried out at 400°C (752°F) in argon for times extending up to 60 min. The grain-size effect was evaluated in terms of average grain width and length values statistically derived from lineal intersection measurements.4 A similar method was applied in establishing the average interfiber spacing, i.e., average perpendicular distance between adjacent planar fibers. The creep characteristics of the alloys were investigated by means of constant-load and constant-stress creep tests. The former tests were conducted at 25°C (77°F) under an initial stress of 10,000 psi, while the latter were performed in the range from 25°C (77°F) to 90°C (194°F) at stress levels varying from 8000 to 22,000 psi. Total specimen strain, as determined with Budd HE-1161-B strain gages, was in excess of 0.10. Maintenance of constant stress was achieved through periodic load reductions made at 0.01 strain intervals to compensate for the attendant incremental reduction in specimen cross-sectional area. The maximum indicated error in the applied stress at these strain intervals was less than 3.0 pct. RESULTS AND DISCUSSION Constant-Load Creep. In an effort to clarify the in-terrelation between interfiber spacing and grain size with respect to the creep resistance of the Zn-Ti alloys, their separate effects on secondary creep rate were determined as a function of titanium content and rolling reduction. These results are set forth in Figs. 1 and 2, respectively. The average grain diameter plotted in Fig. 2 was resolved from average grain width and length values. No data are presented for reductions of less than 50 pct because of the inability to obtain consistent measurements on these strips. The curves of Fig. 1 indicated that, for a given titanium content, a decrease in interfiber spacing, as produced with increasing reduction, promoted a decrease in creep rate. Depending on titanium content, however, wide variations in creep rate occurred at the same interfiber spacing suggesting that interfiber spacing, by itself, has little or no influence on creep resistance. Grain size, on the other hand, decreased progressively with both increasing rolling reduction and titanium content, the effect of which led to a pronounced decrease in creep rate, particularly when the average grain diameter became smaller than 3.0 x 10"4 in., Fig. 2. The continuity of this relationship tended to support the view that grain size rather than interfiber spacing was predominant in controlling secondary creep. Annealing Effect. The observed dependence of creep flow on grain size suggested that a further contribution to creep resistance would result when the alloys were annealed to effect a coincidence between grain width and interfiber spacing, see Fig. 3(b). ~eiides creating an immediate barrier to grain boundary movement, annealing offered the possibility of providing increased structural stability by eliminating many high-energy, mobile grain boundaries.= To test this hypothesis, specimens from the Zn-0.16 Ti strips reduced 75 and

Jan 1, 1967

By Gust Bitsianes, Joseph H. M. Beaty

Successful blast-furnace operation depends upon securing an optimum balance between a number of important variables. This balance will vary somewhat from furnace to furnace in the same plant and with raw materials available in different plants. It is difficult to isolate the effect of any one variable unless it has a rather pronounced effect upon the efficiency of operation. The physical properties of iron ore and coke are known to affect the process, yet it is difficult to set up any definite yardstick by which these differences can be appraised. In recent years, whenever practicable, operators have taken steps to obtain better control over the absolute size and uniformity of size of the ore and coke. The size and physical character of the stone, however, have received comparatively little attention, emphasis being placed upon chemical composition, fluxing efficiency, and action as a desulphurizing agent. Since the stone occupies only about 10 per cent of the volume of the stock column, its influence upon permeability is less than that of the ore and the coke. The large pieces now used have a tendency to roll to the center and thus increase the permeability of this part of the stock column. Smaller pieces would be more effective in promoting the permeability of denser portions of the stock. The size and physical properties of blastfurnace stone are important also for reasons best understood by considering the results obtained by the crushing and the sizing of iron ore. Crushing ore to about 2 in. at Provo, Utah, and to about I in. in Alabama produced material somewhat less permeable to gases, even though sized. In spite of some sacrifice in permeability, the efficiency of the process was improved by crushing and sizing the ore, as indicated by a substantial saving in fuel and increased output. This saving in fuel is due in large measure to more thorough reduction of ore in the upper part of the furnace and to a corresponding decrease in the amount of carbon consumed prematurely above the tuyeres by the reaction CO2 + C = 2CO - 70,080 B.t.u. [I] The physical properties of stone, its size and rate of calcination are important because they influence the rate at which CO2 is released and the completeness of calcination before reaching a level in the furnace where the temperature does not exceed 1050°C. (1920°F.). Briefly, carbon dioxide from the limestone or from the reduction of ore may cause premature corn bustion of carbon above the tuyeres. Assuming that 1000 Ib. of limestone is used per ton of pig iron, about 435 Ib. of CO2 will be liberated during calcination of a good grade of stone. If all this CO2 from the stone were to oxidize carbon prematurely, about 120 lb, would be consumed above the tuyeres in a heat-absorbing reaction. The amount of carbon thus consumed when a

Jan 1, 1943

By Joseph H. M. Beaty, Gust Bitsianes

Successful blast-furnace operation depends upon securing an optimum balance between a number of important variables. This balance will vary somewhat from furnace to furnace in the same plant and with raw materials available in different plants. It is difficult to isolate the effect of any one variable unless it has a rather pronounced effect upon the efficiency of operation. The physical properties of iron ore and coke are known to affect the process, yet it is difficult to set up any definite yardstick by which these differences can be appraised. In recent years, whenever practicable, operators have taken steps to obtain better control over the absolute size and uniformity of size of the ore and coke. The size and physical character of the stone, however, have received comparatively little attention, emphasis being placed upon chemical composition, fluxing efficiency, and action as a desulphurizing agent. Since the stone occupies only about 10 per cent of the volume of the stock column, its influence upon permeability is less than that of the ore and the coke. The large pieces now used have a tendency to roll to the center and thus increase the permeability of this part of the stock column. Smaller pieces would be more effective in promoting the permeability of denser portions of the stock. The size and physical properties of blastfurnace stone are important also for reasons best understood by considering the results obtained by the crushing and the sizing of iron ore. Crushing ore to about 2 in. at Provo, Utah, and to about I in. in Alabama produced material somewhat less permeable to gases, even though sized. In spite of some sacrifice in permeability, the efficiency of the process was improved by crushing and sizing the ore, as indicated by a substantial saving in fuel and increased output. This saving in fuel is due in large measure to more thorough reduction of ore in the upper part of the furnace and to a corresponding decrease in the amount of carbon consumed prematurely above the tuyeres by the reaction CO2 + C = 2CO - 70,080 B.t.u. [I] The physical properties of stone, its size and rate of calcination are important because they influence the rate at which CO2 is released and the completeness of calcination before reaching a level in the furnace where the temperature does not exceed 1050°C. (1920°F.). Briefly, carbon dioxide from the limestone or from the reduction of ore may cause premature corn bustion of carbon above the tuyeres. Assuming that 1000 Ib. of limestone is used per ton of pig iron, about 435 Ib. of CO2 will be liberated during calcination of a good grade of stone. If all this CO2 from the stone were to oxidize carbon prematurely, about 120 lb, would be consumed above the tuyeres in a heat-absorbing reaction. The amount of carbon thus consumed when a

Jan 1, 1943

By E. C. W. Perryman

The recovery of X-ray line broadening, hardness, and electrical resistivity from cold worked AI-Mg alloys has been investigated. The results, together with those from density measurements, suggest that magnesium atoms freeze in the excess vacancies formed by cold working, and that this affects the climb of dislocations during the recovery process. PREVIOUS work1, " has shown that while 1 pct Mg increases the activation energy for recrystalliza-tion, it decreases the activation energy for the recovery of mechanical properties and decreases the subgrain size both after cold working and annealing. A similar result has been reported by Varley2 for an A1-2 pct Mg alloy. With plastic deformation at high temperatures, McLean and Farmer&apos; and Rachinger have found that magnesium appears to retard the motion of dislocations and, furthermore, they find little or no effect of magnesium on the size of subgrains formed during high temperature deformation. In view of the apparent contradictions as to the effect of magnesium on subgrain size, the recovery process in Al-Mg alloys has been investigated more thoroughly by studying the annealing out of X-ray line broadening, hardness, and electrical resistivity from alloys cold worked at room temperature. Material Used—The chemical analyses of the alloys are given in Table I. Fabrication—The material used was cold rolled 20 pct at room temperature, the grain size prior to the last cold rolling operation being similar to that used in previous work; i.e., 230. The experimental procedure for annealing, determination of X-rav half-veak breadth. hardness measurement, electEica1 resistivity, and density and metallographic examination was exactly the same as previously described." Variation of X-Ray Half-Peak Breadth with Annealing Time—Isothermal annealing curves at 100°, 200°, and 250°C were obtained for material cold worked 20 pct. The half-peak breadth of the (333) Ka, line directly after cold working is shown as a function of magnesium content in Fig. 1. Only with the 2.87 pct Mg alloy was overlapping of the a, and n.. reflections observed to any appreciable extent. To separate these, Rachinger&apos;s method&apos; was used. Typical isothermal annealing curves are shown in Figs. 2 and 3 for 100" and 200°C, respectively. These curves are similar to those obtained previously for super-purity aluminum except that the

Jan 1, 1957

By S. D. Strauss

The marketing of nonferrous metals and of the ores and concentrates from which these metals are recovered is a fascinating trade, international in character, sensitive to every change in the economic tide, and complex in its organization. Each individual metal has its own marketing mechanism; no two are exactly alike. The differences sometimes are a matter of tradition rather than of necessity, but usually they have developed because of the very nature of the problems of producing or consuming the individual metal. This description, because of limitations of space, can do no more than indicate the major aspects of the trade and touch lightly on the marketing structure of each metal. The dictionary states that a market is a "meeting of people for selling and buying." In the case of nonferrous metals this meeting may occur on a half-dozen different occasions between the time the ore has been first mined and the time the refined metal is available for use by industry; or it may not occur at all until after the metal itself has been rolled, drawn, stamped, cast, or forged into a useful semifabricated shape. To illustrate: A Chilean miner may sell his small ore production to a custom mill, which produces concentrates that are sold to an ore dealer, who finances shipments of the concentrate to a custom smelter, which buys them for conversion into blister, to be subsequently refined into electrolytic copper (sometimes by a refinery having no corporate ties with the custom smelter) and sold. Conversely, aluminum production is mostly by integrated concerns that mine bauxite, convert it to alumina, smelt that to produce aluminum, and then fabricate that into semifinished or even finished products before title to the material changes hands for the first time. Some nonferrous ores are not converted into metal at all but are sold by the miners or dealers directly to the ultimate consumers. A good example would be chrome ores used by the chemical industry. And of course a substantial part of the commerce in nonferrous metals is in scrap, which is the reconversion into useful form of metals that have long since been mined and smelted. Thus, one-third of all the lead used in the United

Jan 1, 1964