Search Documents

By T. M. Geffen, J. L. Sanderlin, F. F. Craig, D. W. Moore

Scaled reservoir models have been used to study the effect of gravity on oil recovery performance in frontal-drive operations; namely, water, gas, or solvent flooding. The difference in density between the reservoir oil and the injected fluid causes their segregation, resulting in a non-uniform advance of the fluid front. In the laboratory flow tests, which simulated both five-spot and linear injection operations in flat reservoirs, the viscous, capillary, and gravity forces present in these operations were scaled. Dyed fluids were used so that the gross movement of the injected fluid could be observed. The studies covered a range of injection rates, formation thicknesses, and rock and fluid properties normally encountered in field operations. The results of the model tests indicate that the volume of the reservoir contacted by the injected fluid at its breakthrough into the producing well is less than that expected based on information which neglects gravity effects. This difference can often be as much as 80 per cent by gas or water injection in uniform sand bodies. Preliminary flow tests on a non-uniform sand body indicate that the uniformity of the flood fronts may in some situations be influenced to a much greater degree by permeability variations within the rock body than by gravity effects. The magnitude of fluid segregation due to gravity is controlled by the average injection rate, rather than day to day or week to week variations. INTRODUCTION One of the important factors controlling the oil recovery from a frontal-drive operation, such as water, gas, or solvent injection, is the volumetric sweep efficiency. This factor is a measure of the gross portion of the reservoir that is contacted by the displacing fluid. The volumetric sweep efficiency is influenced by gravity effects, well arrangements, and variations in rock permeability within the reservoir. The gravity effects are due to the displacing fluid being of different density than the reservoir oil. This causes the displacing fluid to move preferentially toward either the top or bottom of the formation. Non-uniform advance of the flood front can be caused by the relative positions of the injection and production wells. Variations in rock permeability also result in an uneven advance of the displacing fluid. Gas zones, representing paths of low resistance, may result in non-uniform movement of the injected fluid. The more uneven the advance of the displacing fluid, the lower is the volumetric sweep efficiency and thus the lower the oil recovery efficiency. The effects of well arrangement and permeability variations, upon the gross movement of the injected fluid have been the subjects of extensive investiga-ti0ns.1,2,3,4,5,6 Gravity effects have been recognized as being present in frontal-drive operations'.' but there has been little quantitative measure of their magnitude. Very likely the reason gravity effects have not been studied is that this problem does not lend itself to simple experimental or mathematical analysis. The development of reservoir modeling techniques has made possible a quantitative determination of the effect of gravity on fluid segregation and thus upon the oil recovery performance of frontal-drive operations. This paper presents a progress report on a laboratory investigation of gravity effects in fully liquid-saturated, horizontal, uniform as well as non-uniform systems. These results were obtained from scaled experiments on both linear and five-spot systems within the range of conditions normally encountered in secondary recovery operations. This study is concerned with the gross movement of the injected fluid to the time it first reaches the production wellbore. Therefore, it should be emphasized that the results of this paper can not be used to determine the effect of gravity segregation on oil recovery efficiency at abandonment conditions. MODEL SCALING The science of scaling models is relatively new as applied as petroleum production problems, Many of the scaling techniques have been adaptions of those used in basic studies of heat and fluid flow. There are

Jan 1, 1958

By E. J. Freeh, W. E. Horst

Mathematical models of a continuous comminution process are developed as an extension of the batch grinding model. Pilot-scale experimental work is described and the results are used to demonstrate the capability of the comminution models to simulate observed behavior over a relatively wide range of process variables.

Jan 1, 1973

By R. W. Raymond

CLARENCE King born January 6,1842, at Newport, R. I. His ancestors on both sides mere New Englanders, of English blood, and among them not a few distinguished themselves in art, science, politics or commerce. His grandfather, Samuel Vernon King (partner in 1803 in the house of Talbot, O1yphant & King, later known as King $ Co.), was a pioneer in the China trade, and four of his sons succeeded him in the business. Three of the four died in the far East; and one of

Jan 1, 1903

By W. Luyken

A NUMBER of articles have been published, notably those by R. S. Handy, R. T. Hancock and A. P. Watt in Engineering and Mining Journal, dealing with the calculations involved in ore dressing.. These publications demonstrate both, the importance of the subject and the lack of success in developing a generally recognized method for comparing enrichment effects. Considering that we may wish -to compare enrichment results on similar or dissimilar ores, that we may desire to make the comparison on the basis of either the absolute or the economical efficiency, and that the number of factors upon which the result depends is large, the question arises whether it is possible to set up a positive method for such calculations. In the following pages it is our aim to show that a sure, complete and successful way to overcome existing difficulties has been found. GRAPHICAL ANALYSIS OF ORE-DRESSING PROCESSES The following is from Truscott's Text Book of Ore Dressing (London, 1923) x = assay of ore treated (feed). y = assay value of the concentrate. z = assay value of the tailing. a = weight of feed. b = weight of concentrate. c = weight of tailing. C = fractional concentration = b/a= x-z/y-z (1) K = ratio of concentration = 1/C = a/b =y-z/x-z (2) R = fractional recovery = yb/xa = Cy/x. (3) 100R = percentage recovery. Copt = theoretically best concentration. 100 - Copt = waste in the feed.

Jan 1, 1929

By E. K. C. Williams, Nathaniel Arbiter

INTRODUCTION The surface processes involved in preparing ores for flotation and for operations depending on their flocculation/dispersion characteristics * vary widely in agitation dependence. Most of the reagents used for these purposes are added to grinding circuits, pump sumps, launders, or directly to flotation cells with the turbulent flow conditions usually adequate both for mixing reagents and for surface reactions without special conditioners. However, some reagent systems do require specific control of agitation intensities and reaction times, the more important of these being the following: 1. Activation of ZnS with CuSO4. With the usual conditions pH about 10, with collector added with the CuSO4, Cu 2+ is almost completely precipitated as basic compounds and as collector salt. As a result the levels of reagent in solution are extremely low which probably accounts for the need for separate conditioning. The agitation intensities are at about the 0.01 HP/ton level.** 2. Flocculation with natural or synthetic polymers. In this case the agitation problem is two-fold; first, to insure adequate initial mixing of the viscous stock solution of the

Jan 1, 1980

NEW MEMBERS The following list comprises the names of those persons who became members during the period of June 10, 1917, to July 10, 1917. BANKS, LEON MAXWELL Agent 3. Supt., Grant Leasing Co. Metcalf Ariz. BEAUCHAMP, HENRY CLAY : Mine Operator, Sisson, Siskiyou Co., Cal. BOCKING, CHARLES, Asst. Mgr., Butte & Superior ,Mining Co., Rialto Bldg., Butte, Mont. BEYER, HERMAN E., Chief Engr., Condenser Dept., Ingersoll-Rand Co., 11 Broadway, New York, N. Y. BLACK, HERBERT F 1512 Oliver Bldg., Pittsburgh, Pa. BRENNAN, PATRICK J., Gen'l. Supt., Elkhorn Division, Consolidation Coal Co., Jenkins, Ky. BUTNER, DANIEL W., Chem. & Supt., Underground Min., Spanish American Iron Co., Daiquiri, Santiago de Cuba, Cuba. CARLTON, DAVE P Nevada-Douglas Cons. Copper Co., Ludwig, Nev. DE AROZENA, JOE Min. Engr., 321 Preusser St., San Angelo, Texas. DICKIE, CHARLES HERBERT, Pres., Georgia River Min. Co., Duncan, Vancouver Island, B. C., Canada. DOBBINS, WALTER Mill Foreman, Chino Copper Co., Hurley, New Mexico. DRURY, CHARLES W., Asst. Professor of Met., Queen's University, Kingston Out. Canada.

Jan 8, 1917

By Robert Y. Grant

This study outlines the history of metal mining in Japan and the characteristics of the industry as they existed from 1925 to 1945. Mining and milling operations are described together with the role of the Japanese Government. A description of post-hostilities conditions and the present state of the industry is included. MANY of Japan's larger and better known mines date back to the early centuries of the Christian Era. The first stimulus to mining in Japan came through the growth of Buddhism, A. D. 600 to 700, and the attendant need for copper and other metals for temple ornaments and statues. During the Feudal period, 1333 to 1568, mine operations were expanded to meet the demand for ornament metal and for financing of campaigns. After removal of the seat of government from Kyoto to Tokyo, about 1600, the Tokugawa Shogunate placed great emphasis on mining, and many new mines were opened, some of which are still operating. Toward the end of the Tokugawa period, mining had declined sharply from its earlier peak. The easily worked, high grade portions of the orebodies had been exhausted, and the mining techniques then available could not exploit the deeper, lower grade ores. Similarly, extraction of metal from the sulphide ores presented a major problem. With the Meiji Restoration in 1868 and the rapid opening of the country to western ideas came a rejuvenation of the mining industry. Mining, milling, and smelting processes were greatly improved, resulting in the extension of development work into hitherto inaccessible portions of orebodies. The demand for metal during World War I stimulated activity throughout the industry; copper mining, particularly, expanded to a point where Japan ranked second among world producers.* During the depression following the war, mining underwent a severe contraction in activity, recovering slowly during the late 1920's only to undergo a further setback in the worldwide depression which started in 1929. Mineral output declined in 1930, but the beginning of Japanese expansion, 1931 to 1932, brought about an increase in the output of mine products starting between 1932 to 1934. Production continued to rise, the peak output being attained 1939 to 1943 in virtually all commodities. The greatest production of iron ore, chromite, and manganese was not experienced until 1944 when blocked imports, coupled with strong demands for steel, provided the needed incentive. Through necessity, Japan produced much of her mineral needs from her own mines at high cost during World War 11. Taking the 1932 to 1936 period as an average, however, Japanese mines produced only 16 pct of the iron available to industry, 8 pct of the lead, 33 pct of the zinc, and 68 pct of the copper. Nearly all of Japan's output of gold, silver, copper, lead, and zinc between 1925 and 1945 came from 30 to 49 pct of the mines for which production data are available; for example, 66 of 174 gold-silver mines accounted for 98 pct of the output of this group. Further analysis of mine output indicates that a large part of Japan's metal output was derived from a few large mines; about 10 gold-silver, 15 copper, 3 lead-zinc, 5 manganese, and 2 iron mines account for most of the production. Many of these mines have been operated for 200 to 400 years. With the

Jan 1, 1952

1. What Is a Rock Burst? . . . . 569 Jack Spalding . . 569 A. F. Robertson . 569 W. R. Crane . 569 G. S. Rice......569 P. J. Shenon........... 569 L. C. Graton........... 569 2. What Are the Causes of Rock Bursts? 573 Jack Spalding..........573 A. B. Yates and P. J. Shenon 574, 578, 592, 596 A. F. Robertson . . . . . 575, 595 W. R. Crane. ... 579 G. S. Rice.........582 Oscar Weiss .........582 P. B. Bucky..........582 P. H. Bird.....588, 592, 593, 595 M. K. Hubbert.........593 G. Wheeler.......... .593 B. F. Tillson........593, 595 T. T. Read............594 3. How Can Rock Bursts Be Prevented?. 597 Jack Spalding..........597 A. B. Yates and P. J. Shenon ... 598 A. F. Robertson.......599 W. R. Crane....... .602 G. S. Rice............602 Page 4. How Can Rock Bursts Be Predicted?. 602 Jack Spalding.........602 A. F. Robertson.......602, 603 A. B. Yates and P. J. Shenon ... 602 W. R. Crane......602 G. S. Rice......602 B. F. Tillson...........603 5. How Can Rock Bursts Be Controlled? 603 Jack Spalding..........603 A. F. Robertson.......603 W. R. Crane...........604 A. B. Yates and P. J. Shenon 604 Oscar Weiss........605 G. S. Rice......- 604, 609 R.D.Hoffman..609, 610 R. D. Hall..........609 R. H. Cromwell . . 609 P. J. Shenon...........609 P. B. Bucky......609, 611 B. F. Tillson.........609, 611 A. B. Yates...610, 611 P. H. Bird.......610 6. General Discussion........ 611 Jack Spalding.......... 611 R. D. Parker....... . 616 C. Baring Horwood........ 618 P. B. Bucky........... 619 Foreword This symposium brings together points of view, experiences and ideas on rock bursts from a goodly portion of the globe. Some conceptions, particularly those regarding the necessity of depth, have been fairly well shattered, as we find that they are present in the water tunnels of New York, on the surface at marble quarries in Vermont, and in the coal mines of the United States, as well as in the deep mines of the South African and Kolar gold fields, and in the nickel, copper and gold mines of Canada. Their occurrence under such a variety of conditions is, therefore, a challenge, which, if successfully met and overcome,

Jan 1, 1946

By T. B. Massalski, H. W. King

An hcp phase may be induced by cold working the ß&apos; phase of the Ag-Zn system. This phase reverts to ß&apos; on subsequent aging. No phase change occurs on cold working the o phase, but ß&apos; is formed when the deformed alloy is subsequently aged at room temperature. It is concluded that for alloys near 50 at pct Zn the ordered bcc ß&apos; phase is the equilibrium structure at room temperature. WhEN the disordered bcc ß phase of the Ag-Zn system is cooled to temperatures below 258o to 274oC, it transforms to a complex hexagonal phase <o.1,2 The nature of the o ß=o transformation has been the subject of some discussion,2&apos;3 and the structure of o has been described in detail.&apos; The latter phase appears to be stable on aging at room temperature but decomposes following cold work. When alloys containing approximately 50 at. pct Zn are rapidly quenched from the 0 phase field, the ß ? o transformation may be suppressed; but the ß phase undergoes an ordering reaction (ß ? ß&apos;). The ß&apos; structure may also be obtained as a result of cold working and aging at room temperature.4 Kitchingman, Hall, and Buckley4 have suggested that the decomposition of (o following cold work proceeds in two stages, (o ? ß followed by ß ? ß&apos;, but did not confirm this by experiment. When the ordered &apos; phases in the systems Cu-Zn5 and Ag-Cd6 are cold worked, they become unstable and transform to a close-packed hexagonal phase (( ) indicating that when order is destroyed in a ß&apos; structure the close-packed hexagonal phase may in many cases be more stable. It thus became of interest to study more closely the effect of cold work and annealing on the stability of both the ß&apos; and o phases in a Ag-50 at. pct Zn alloy. Predetermined weights of spectroscopically-pure Ag and Zn, supplied by Johnson and Matthey, were melted and cast under 1/2 atm of He in transparent vycor tubing. The ingot was homogenized for 1 week at 630°C and quenched into iced brine. Since mechanical polishing was found to induce a phase change, sections were first polished at room temperature, sealed in tubes under 1/2 atm of He, reannealed for several days at 630o or 200°C and then quenched into iced brine. Sections of the alloy thus prepared were found to be homogeneous when examined under the microscope. The sample quenched from 630°C (ß -phase region) was pink in color, whereas the sample quenched from 200°C (o-phase region) was silver. The latter sample showed the characteristic hexagonal anisotropy when examined under polarized light. Filings of the alloy were examined at room temperature, after various heat treatments, using an RCA-Siemens Crystalloflex IV diffractometer with filtered CuKa radiation. The X-ray reflections from flat powder specimens quenched from 630o and 200°C and sieved through 230 mesh were recorded graphically at a scanning speed of 1/2 deg per min. The resultant patterns are shown in Figs. 1(a) and 1(b) and may be identified as those of the 8&apos; and <02 structures respectively. The lattice parameter of the ß&apos; phase was determined as 3.1566Å.* This value compares very well withthatto be expected for a 50 at. pct Zn alloy from the data of Owen and Edmunds? and indicates that no loss of Zn occurred during casting. In order to study the effect of cold work upon the ß&apos; and o phases, filings made at room temperature and sieved through 230 mesh were mounted immediately in the diffractometer-i.e., without a strain-relief anneal. Changes in structure on subsequent aging were followed by scanning repeatedly over the regions of the low index reflections of the ß&apos; and o structures-i.e. , 28 from 35 to 44 deg. Immediately after filing the 8&apos; specimen, additional diffraction peaks were observed in the low-index region of the pattern, as shown in Fig. 1(c). These additional peaks do not coincide with those of the o structure, Fig. l(b), but may be indexed as the (10.0), (00.2), and (10.1) reflections of an hcp phase (<) with nearly ideal axial ratio. However, this hexagonal phase appears to be very unstable since within a very short time at room temperature it reverts back to the ordered ß&apos; phase, the reversion being complete within seven hours. The 5 ? ß&apos; reversion reaction is, therefore, very similar to those already reported in Cu-Zn5 and Ag-Cd6 7&apos;alloys. The action of filing caused the deformed surface of the originally pink ingot to become silver in color, indi-cating that the ( phase possesses similar reflecting properties to the o phase. Hence, the subsequent

Jan 1, 1962

By Fred W. Gordon

The heading of this paper was prompted by the knowledge that experience, up to this time, seemed to indicate that smaller furnaces were preferable for smelting the material of this section. Since the reasonable success thus far achieved by the first furnace of this plant tends to change the above opinion, and unsettle the generally-accepted views of furnace-men as to "weak " coke, a few words as to the design of the plant and the mode of operation adopted may prove interesting.

Jan 1, 1889

By George S. Lockwood

Plans are moving ahead toward the July 1965 start-up date for Kaiser Steel Corp.’s new pelletizing plant at its Eagle Mountain, Calif., iron mine. Capacity will be 2 million long tons of pellets containing 65% Fe. A major portion of the output is scheduled for charging into Japanese blast furnaces as the result of a contract to supply Mitsubishi interests with 10.8 million tons of pellets over a six-year period. Kaiser&apos;s concentrating plant at Eagle Mountain plus sintering facilities at Fontana are adequate to meet the requirements of its blast furnaces, which, as a consequence, are not expected to take any substantial quantity of pellets during this period. However, some 200,000 tons of pellets per year is scheduled to be used for the production of special steels and in the open hearths as a substitute for the high-cost ores now being used.

Jan 8, 1964

By Edward W. Parker

At the Seventy-sixth meeting of the Institute, held in New York, N. Y., February, 1899,I presented a paper on this subject entitled, Coal-Cutting Machinery,&apos; which has become somewhat out of date, in view of the decade&apos;s development in this feature of the coal-mining industry. It should be explained that the present paper is limited to the use of mining-machines in bituminous mines. Practically all of the anthracite mined is "shot from the solid," no undercutting being done. Anthracite-mining is therefore not considered in the statistics or other references. The statistical record as compiled by the U. S. Geological Survey shows that in 1898, the year preceding the presentation of my former paper, there were 32,413,144 short tons of coal undercut by the use of machines. In 1907 the machine-mined coal-product amounted to 138,547,823 short tons. In sympathy with the general decrease in coal-production during 1908, the output of machine-mined coal decreased to 123,183,334 short tons, but the proportion of machine-mined coal to the total output, nevertheless, showed an increase, from 35.1 per cent. in 1907 to 37 per cent. in 1908. In 1898 only 19.5 per cent. of the total product was unclercut.by the use of machines. The number of in use in the bituminous mines of the United States has increased from 2,622 in 1898 to 11,144 in 1907, and to 11,569 in 1908. The total production of bituminous coal in the United States in 1908 mas almost exactly double that of 1898, while the machine-

Jan 1, 1911

[United States PAGE Alabama 226 Alaska 226 Arizona 226 Arkansas 227 California 227 Colorado 230 Connecticut 231 Delaware 282 District of Columbia 232 Florida 232 Georgia 232 Idaho 232 Illinois 233 Indiana 234 Iowa 234 Kansas 234 Kentucky 234 Louisiana 235]

Jan 1, 1928

By G. S. Brooks

The tendency of the oxides of such metals as aluminum, zinc, chromium, and calcium to form compounds at high tempera tures with iron oxide is well established by past investigation. Data of this reaction, as developed in laboratory research, have been contributed by Burleigh, Hofman, and Wells, in America, and by many others abroad. A partial bibliography of the subject is appended. From these authorities we learn that the ferric oxide here has the function of an acid, giving in the case of ZnO a zinc ferrite, with a normal composition of ZnOFe2O3 This formation of zinc ferrite particularly affects the success of such processes as leaching or magnetic separation, and thus becomes practically important to the metallurgist. But the meager existing data do not entirely agree; and quantitative results from muffle-practice are conspicuously absent. Furthermore, it being of some general importance to the zinc smelter in both roasting and reduction, the following few notes of operations oil a commercial scale are contributed: I. Physical Properties of Zinc Ferrite. As formed for the most part synthetically by investigators, zinc ferrite exhibits characteristic physical properties, such as octahedral crystals, dark color, and a density over 5, together with a slight magnetic attractability. In examining with the microscope many products of mechanical muffle-roasting kilns, it is, however, impossible to find individual grains which can be identified as consisting entirely of zinc ferrite. The variety of colors, especially where each grain of blende was mechanically free from marcasite, rather conveys the impression of a partial ferritization of the grain. One side or end, for example, may often have the hard, dense surface and dark red to black color of the ferrite, while the balance shows the usual light yellowish brown of a normal iron-free blende.

Jan 1, 1914

US 4,183,899 - Flow process for chlorinating ilmenite. A laminar flow of a mixture of ore, a carbonaceous reductant, and chlorine gas or other chlorinating agent is passed through a reaction zone maintained at a temperature of 1350 to 1950°C and a product stream Including titanium tetrachloride is withdrawn from the zone. The atomic ratio of carbon to oxygen in the feed mixture is greater than 1:1, and the molar ratio of chlorine to titanium solids In the product stream is between about 0 5.1 and 2:l. Titanium chlorides and metallic iron are recovered separately from the product stream. J.P. Bonsack, assigned to SCM Corp, Jan. 15, 1980 21 pp. (423-79). Filed. 3-10-78 (885,442).

Jan 1, 1982

Jan 1, 1937

By John J. Secretary Egan

The present list of problems relating to the physical chemistry of steelmaking has been prepared by the Committee on the Physical Chemistry of Steelmaking, from answers to a questionnaire submitted to a number of metallurgists engaged in both industrial and educational work throughout the United States. The purpose of the project is to make available to research laboratories a list of problems, all reduced to their simplest terms, the solution of which would aid in creating a better understanding of the steelmaking process. It is not intended to restrict the problems to practical steelmaking. The list also includes the study of the properties, and their correlation, as well as the physical and chemical reactions, of all substances that occur or that may be in any way associated with steelmaking operations, such as metallic substances, refractories, nonmetallic inclusions, and the constituents of slags. Many of the problems can be carried out in university or other research laboratories. Others may be most successfully attacked by cooperation of the research men with the operating personnel. It is the Committee&apos;s earnest wish that this cooperation be fostered. It is requested that investigators who are working on any of the problems listed and who anticipate future publication of their results, notify the Secretary of the Committee that such investigation is in progress. Suggested additions to the present list are also requested. The Committee is undertaking to act as a clearing house for information regarding the topics in this field that are being actually studied. Interested persons are invited to correspond with the Secretary. I. Data involved in the state of equilibrium for the various systems (laboratory work, almost entirely). A. Specific heats, heats of formation, entropies and free energies of various PURE ELEMENTS OR COMPOUNDS; ALSO CERTAIN TYPICAL SLAGS AND REFRACTORIES I. Determination of specific heats and entropies of oxides, sulphides, nitrides, etc, over a wide temperature range. 2. Determination of free energies of oxides, sulphides, nitrides, etc., over a wide temperature range. 3. Determination of the heats of formation of the oxides, sulphides, nitrides, etc. 4. Determination of the thermodynamic properties of the more important mineral-ogical constituents of the basic open-hearth slags such as calcium silicates, calcium phosphates, calcium ferrites, manganese silicates, FeO and Fe2O3. 5. Determination of the specific heats of open-hearth slags, including liquid silicates, if possible.

Jan 1, 1941

By John J. Secretary Egan

The present list of problems relating to the physical chemistry of steelmaking has been prepared by the Committee on the Physical Chemistry of Steelmaking, from answers to a questionnaire submitted to a number of metallurgists engaged in both industrial and educational work throughout the United States. The purpose of the project is to make available to research laboratories a list of problems, all reduced to their simplest terms, the solution of which would aid in creating a better understanding of the steelmaking process. It is not intended to restrict the problems to practical steelmaking. The list also includes the study of the properties, and their correlation, as well as the physical and chemical reactions, of all substances that occur or that may be in any way associated with steelmaking operations, such as metallic substances, refractories, nonmetallic inclusions, and the constituents of slags. Many of the problems can be carried out in university or other research laboratories. Others may be most successfully attacked by cooperation of the research men with the operating personnel. It is the Committee&apos;s earnest wish that this cooperation be fostered. It is requested that investigators who are working on any of the problems listed and who anticipate future publication of their results, notify the Secretary of the Committee that such investigation is in progress. Suggested additions to the present list are also requested. The Committee is undertaking to act as a clearing house for information regarding the topics in this field that are being actually studied. Interested persons are invited to correspond with the Secretary. I. Data involved in the state of equilibrium for the various systems (laboratory work, almost entirely). A. Specific heats, heats of formation, entropies and free energies of various PURE ELEMENTS OR COMPOUNDS; ALSO CERTAIN TYPICAL SLAGS AND REFRACTORIES I. Determination of specific heats and entropies of oxides, sulphides, nitrides, etc, over a wide temperature range. 2. Determination of free energies of oxides, sulphides, nitrides, etc., over a wide temperature range. 3. Determination of the heats of formation of the oxides, sulphides, nitrides, etc. 4. Determination of the thermodynamic properties of the more important mineral-ogical constituents of the basic open-hearth slags such as calcium silicates, calcium phosphates, calcium ferrites, manganese silicates, FeO and Fe2O3. 5. Determination of the specific heats of open-hearth slags, including liquid silicates, if possible.

Jan 1, 1941

By Frank S. Gardner, Morris Cohen, Dara P. Anita

There is a conspicuous lack of information in the literature on the precise role played by residual quantities of austenite in heat-treated steels. While retained austenite may be expected to have significant effects on such important properties as the impact resistance of tools and carburized parts and the dimensional stability of dies and gauges, attempts to study these problems systematically have suffered from the absence of a reliable technique for ascertaining absolute amounts of austenite. With such a technique, not only could the relation between residual austenite and service behavior be investigated, but the chemical and heat-treatment factors that control the quantity of the austenite could also be established. Thus, the retained austenite content could then be regulated in accordance with the results desired. The presence of retained austenite may be inferred by observing the changes in properties (hardness, specific volume, electrical resistance, etc.) due to its decomposition on subatmospheric cooling1 or on tempering,2 but these indirect measurements are not readily translated into percentages of austenite. Quantitative determinations have been achieved in special cases by means of dilatometric3 and magnetic4,5 measurements; but the former procedure requires that observations be conducted during the hardening and involves difficult calibrations that limit its applicability, while the magnetic procedure is very sensitive to extraneous influences and depends upon assumptions that can only be considered as approximate in an absolute sense. Furthermore, both the dilatometric and magnetic effects are volume properties, and cannot be conveniently utilized to explore variations in retained austenite from point to point in a suecimen. Some microstructures lend themselves to accurate evaluation of retained austenite contents by metallo-graphic methods,3 but such instances are not too common, and at best, the procedure is tedious. The characteristic X-ray diffraction lines of austenite permit positive identification of its presence; and in the present paper the intensities of these lines, or the corresponding densities* on photographic film, are employed to measure the amount of the retained austenite. In order to cancel the effect of uncontrollable variations in the X - ray exposure and film - development conditions, a standard reference line is Superimposed on each film by maintaining a foil of aluminum in the path of the incident X-ray beam during the entire exposure. With different samples of steel and the same foil, the ratio of the density of some one austenite line to the density of

Jan 1, 1943

By V. Patarini, D. Kuehl, F. Galasso, M. Salkind

In recent years, a great deal of research has been directed toward the production of continuous low-density, high-strength, high-modulus boron fibers for aerospace applications. A technique which has proven to be quite successful for forming these fibers involves the reaction of boron trichloride and hydrogen on a hot tungsten wire. In this process, a boron fiber is produced which consists of a tungsten boride core covered with amorphous or crystalline boron depending on the temperature of the preparation.2,3 The purpose of this paper is to present the properties which have been obtained to date from measurements and observations on these fibers. Selected samples of boron filament produced by reacting boron trichloride and hydrogen on a 0.5 by 10-3 in. diam tungsten wire substrate using different reacting temperatures were cross-sectioned, polished, and photomicrographed with cross-polarized light. The temperature of the wire was measured using a two-color optical pyrometer. Photomicrographs of these samples are shown in Fig. 1. Three general types of boron, in addition to the tungsten borides, have been identified by means of X-ray powder diffraction techniques: a) at low temperatures (below 1400°C) the boron is deposited in the amorphous form; b) at temperatures between 1400° and 1500°C the boron is deposited in the ß tetragonal form; and, c) above 1500°C the boron is deposited in the B rhom-bohedral form. In the depositing range of 1400" to 1500°C the boron initially deposits as amorphous and becomes crystalline as evidenced by the large equi-axed grains which then merge into columnar grains in later stages of boron deposition. This can be seen in Fig. 1 and has been observed in the X-ray patterns of these fibers, which contain both halos from the amorphous boron and lines from the ß tetragonal form. Above 1500°C the only boron reflections observed in the X-ray patterns were those of the ß rhombohedral form and only columnar grains are seen in the photomicrographs. Photomicrographs of the surface in Fig. 2 show the smooth-surface kernal-type deposition which corresponds to the amorphous form and the rougher surfaces which correspond to the crystalline form. Mechanical measurements were made on amorphous boron produced at 1300°C rather than the crystalline boron because the strengths of these filaments were greater and were more consistent. A tensile tester consisting of a fixed crosshead containing a double

Jan 1, 1967