Search Documents

By C. W. Parmelee

THE ideal fuel for burning ceramic wares is the one that, among other characteristics, has little or no sulfur. For that reason wood was long considered the most desirable fuel but its high cost has practically eliminated its used except in regions where it is very abundant or other circumstances warrant its choice. The fuels commonly employed are natural and producer gas, oil, and coal. The last named is undoubtedly the most important, not only in this country but abroad. Occasionally anthracite is used but the larger part is bituminous. The quality of the coal used depends on the kind and the value of the products being manufactured. For some materials, such as common brick, hollow block, etc., the quality of the coal is of less importance than in the manufacture of polychrome terra cotta, pottery, porcelain, etc. It is obvious that in burning clays that contain notable amounts of pyrite, marcasite or gypsum, as is the case with many common clays, the sulfur content of the fuel is of much less importance. The permissible amount of sulfur in the coal used will depend on the kind of product being manufactured. "A good sample' of coal commonly used in pottery ovens has something like this quantity of sulfur." PER CENT. Total sulfur 1.20 Sulfur in the ash 0.11 Volatile sulfur a 1.09

Jan 9, 1919

By A. W. Fahrenwald

THE function of the classifier in modern fine-grinding practice is to remove a finished product from the grinding-mill discharge, leaving material that needs further comminution. The classifier, therefore, makes two products: (1) "finished" product, which overflows the rim of the classifier tank, sometimes referred to as "slimes" or as "classifier overflow," and (2) "unfinished" product, which settles to the sloping bottom of the classifier tank and is removed by dragging or raking. This product is generally referred tows "sands" or "oversize." One of the outstanding features of the closed-circuit classifier is its ability automatically to return the unfinished product of the ball-mill discharge to the feed end or scoop box of the ball mill. This is a distinct advantage because it avoids dilution of the ball-mill feed, and, furthermore, the particular method of removing the settled sand, by raking it up the inclined bottom of the classifier, gives a classifier discharge containing a minimum of water. This leads to maximum classifier efficiency, in this type of classifier, because the maximum volume of water is displaced upward by the settling sands. The closed-circuit classifier is required to deliver a finished pulp of closely specified density requirements, therefore added hydraulic water generally is not permitted.

Jan 1, 1930

By J. D. Exner

With the introduction of rotary drilling in the Gulf Coast area, some thirty-two years ago, and its subsequent spread to other producing localities in the United States, there has been a constant change in the design of equipment. Only the general features remain, namely the rotating drill stem and the circulating mud. Only recently have the properties of mud and their behavior received attention from petroleum engineers, but circulating problems in present deep drilling demand further study and understanding. It is the purpose of this investigation to determine the relative changes in the apparent viscosity of muds with changes in temperature and to discover other physical effects due to heat. Very little information has been published regarding the effects of temperature on the viscosity of drilling muds. Maustl states: "The viscosity of most muds is decreased on heating, but the interesting thing is that the degree of flocculation is also increased on heating. There will be a greater tendency to seal off formations at high temperatures than at low temperatures." With regard to the effect of temperature on viscosity and yield point, Herrick2 states: "The variation of yield point and viscosity of mud with temperature.....is not very clearly brought out by the data available. Both appear to decrease slightly with increasing temperature up to 200' F." The experimental results presented in this paper further emphasize this point. Two types of viscosimeters are available for measuring the apparent viscosities of drilling muds: the efflux tube type as used by Herrick3 and Marsh, and the torsional type such as the McMichael or the Stormer viscosimeters. Because of its extensive use in measuring the apparent

Jan 1, 1933

By V. J. Decarlo, J. J. Gilman

POLISHING pure zinc differs somewhat from polishing less reactive metals. The problem is not that of finding a suitable reagent, but rather of producing the polish in such a way that the surface remains polished after it is removed from the polishing bath. In other words., the anodic film that is vital to the polishing mechanism' must be tightly adherent and nonporous. It is usually desirable that it be thin. Polishing solutions consist of proper proportions of an acid and a strong oxidizing agent. In electro-polishing, the external circuit acts as the oxidizing agent. The proportions are critical because the essential surface film must be maintained at approximately constant thickness during the polishing process. In the case of zinc, chiefly two oxidizing agents, chromic and nitric acids, have been used. The simplest polishing reagent is concentrated nitric acid. However, it has certain disadvantages. It tends to pit: an excessive amount of heat is evolved during polishing; and the oxide film that it produces is not very stable, so that the polished sur-

Jan 1, 1957

By Marlin J. Veesaert

Urban quarries offer one of the greatest opportunities for profit in nonmetallic mining with limited financial risk-if properly evaluated, planned and developed to meet market needs. Location, with respect to market, is the prime consideration. Geologic considerations and quality of rock are nearly as important. Cost factors and return on investment (ROI) are the principal financial considerations. Risk of capital is determined by weighing all factors that should be considered and how well judgments are based on information acquired. It is a simple, true axiom of business that an investment must be founded on amount of capital required with its expected return plus profit, expertise required to operate, and time involved. Urban quarries generally offer excellent stone product market opportunities. Costs of land with mineral containment and processing operations are much greater than in rural areas. Environmental problems have become increasingly severe. Competition from other quarries in the market area is usually directly proportional to the profit attractiveness. Risk of capital (initial, developmental and operational) can be evaluated and reduced only by thorough analysis of the entire situation. Time and money expended on planning and preliminary investigations probably represent the most productive investment of available company resources. Basic Reasons to Establish a Limestone Quarry Profit Motive: Certainly the dominant and overriding motive must be that of attaining a reasonable profit. In certain situations a quarry firm may acquire land, necessary rezoning (if required), and satisfy all of the other prerequisites preparatory to beginning operations but delaying the actual development.

Jan 1, 1980

By Alan Morris

In a previous paper1 the results of cutting tests on free-cutting brass rod were reported. Investigation was made of the effects of variation in lead content, microstructure and cold drawing. The author's reply to the discussion of that paper includes a study of the directional cutting properties of drawn and annealed rod. The present paper records the results of tests made on series of samples in which the tin, iron and copper contents have been varied. The apparatus used and method of testing are described in detail in the previous paper. The machine is of the pendulum-operated milling type used and described by Airey and Oxford.2 Angular readings of the height to which the pendulum rises after falling from a fixed position, both when a cut is made and when the pendulum swings freely, give the basis for calculation of the energy consumed in making a cut. Careful weighing of the sample before and after cutting gives a measure of the amount of metal removed. The results are expressed in footpoiinds per cubic inch of metal removed, and have been called "unit cutting energy." In the course of the discussion of the author's earlier paper, W. B. Price reported large-scale tests involving some 50,000 lb. of material. These tests indicated that the addition of as much as 0.6 per cent of iron and 0.25 per cent of tin had apparently no adverse effect on the highspeed cutting characteristics of the rod. The rod also contained a small amount of nickel. The test results reported here tend to confirm his observations. Effect of Variation in Tin Content The castings for this series were made 2 by 1 by 9 in. and were processed as follows: 1. Castings were annealed at 500" C. for 7 hr. 2. Cold-rolled to 0.700 in.

Jan 1, 1933

The Library of the above-named Societies is open from 9 A.M. to 10 P.M. on a11 week-days, except holidays, from Sept. 1 to June 30, and from 9 A.M. to 6 P.M. during July and August. The Library contains about 55,000 volumes, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library can render valuable service through correspondence; letters requesting information will receive special attention. The Library is prepared to furnish references and copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general information as to the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape. The members of the Institute can be of service to the Library by for- warding copies of mining reports, maps privately issued, and similar material, which will be classified, indexed, and made available to other members. Suggestions for additions to the Library, either by purchase or personal solicitation as gifts, will be welcomed. It is hoped that members while in the city will use the Library freely, and assurance is given that most careful service will be rendered to them.

Jan 8, 1916

By Louis D. Huntoon

After the completion, in 1905, of the Hammond Mining and Metallurgical Laboratory of the Sheffield Scientific School, Yale University, it became necessary to secure and assay a large assortment of ore-samples, and to arrange the results in such a manner as to admit of use with the least amount of work on the part of the instructor. At first, pulp-samples, together with their respective assays, were secured from the mines, smelters, and public aesayers, but this practice did not prove satisfactory. It was not only difficult to secure a suffciently large supply of material, but it was also impossible to secure the proper assortment required for instructing students. It involved considerable work for the donors to select the samples and furnish a record of the assays, and also for the instructors to examine each pulp and determine its character. Some of the samples did not contain a sufficient quantity of pulp for the student to check his work in case his first assay did not correspond to the record. In order to increase the number of samples and to vary the character of the material, pulp-samples were later mixed with barren rock and with sulphides, but this method also was unsatisfactory and has been discontinued. At present, small lots of ore are secured by gift or purchase from engineers, public assayers, and the managers of mines, mills, and smelters. These lots weigh from 10 to 100 lb. each, and are rarely finer than 0.25 in. in size. The larger samples permit of a careful study by the instructor in order to determine the best method of assaying to be followed. In universities in which assaying is taught the record of the samples should fulfill the following requirements:

Jan 1, 1910

By P. E. Hopkins

Introduction and History IN speaking of the economic geology of southeastern Ontario, W. G. Miller and C. W. Knight' say that "there occurs in southeastern Ontario a variety of minerals and rocks of economic value, probably as great as in any district of like size on the North American continent. Some of these deposits, including marble and trap, are inexhaustible. Others, including talc and iron pyrites, have proved to be of considerable economic importance. From time to time, during the last 50 years, the following minerals and rocks have been mined or quarried with varying success: gold, iron pyrites, zinc blende, copper pyrites, galena, mispickel, magnetite, hematite, talc, actinolite, mica, marble, ophicalcite, feldspar; fluorite, apatite, corundum, graphite and sodalite. All of the economic materials, with the exception of fluorite, appear to be of pre-Cambrian age. The fluorite veins penetrate the Ordovician, Black River, limestone." Accompanying that report was an article by the writer on the Queensboro Pyrite Area which includes one of the two working pyrite properties in southeastern Ontario. In the present paper will be given a brief description' of all the known pyrite deposits in the area which may at some time possess an economic value, with fuller descriptions of the two working mines-The Canadian Sulphur Ore Co.'s mine near Queensboro, and the Nichols Chemical Co.'s property at Sulphide. The earliest mining of iron pyrites in Ontario was done in 1868 on the Billings property near Brockville. The mines were closed down in 1879 under the assumption that they were exhausted. Many other

Jan 8, 1916

By James T. B. Ives

The map exhibited* as an example of my method of construct ing geological strata-maps is essentially an educational appliance. The method, however, is available for the production of maps of comparatively small areas, which, I am confident, will be found of great practical value to mining engineers. Before stating how the method may be so applied I will briefly describe the map exhibited, as the easiest way of making my meaning clear. Almost any region might be taken. This map represents the eastern half of the United States; and the geology is that of the map issued by the Geological Survey, and revised and extended subsequently by Professor Hitchcock for your Institute. I use ten cards, of the colors used in the geological map, each having the geog raphy of the area printed upon it; and I superimpose these in the order in which the colors occur in the index to the map. I next cut away a portion of each card, excepting the lowest, leaving only so much of each as represents the exposure of the formation of that color plus all those which overlie it. When that is done, the whole, looked at from a distance, appears to be an ordinary geological map. Looked at more closely, however, the formations are seen to overlie one another, as in nature. The cards are covered with glass in a frame, which, hinged at the bottom edge, can be let down. The cards are then found to be all hinged in the same manner, and they, too, may be lowered, one after the-other. I am told by teachers of geology of great experience and the highest reputation that by this appliance they will be assisted in im parting to students the first facts and principles of geological sci ence. Having let down the whole series of cards, until that repre senting the Archaean is seen underlying all the rest, the teacher will gradually rebuild it. The Cambrian will thus be laid down upon the Archaean before the eyes of the class, the Silurian upon that,

Jan 1, 1888

By F. D. Mahone

Much crude oil, as produced from the well, carries varying amounts of water, which may be present as free water in globules sufficiently large to settle out, in time, if the fluid is allowed to stand, or as an emulsion formed by myriads of minute water particles, each surrounded and entrapped by a film of oil through which it cannot break under the action of gravity alone. Such an emulsified mixture of oil and water is commonly termed "cut oil." When such an emulsion is subjected, under proper conditions, to the influence of a high-potential alternating-current field, the minute water particles rupture the enveloping oil films and coalesce into larger water droplets this procedure continuing until all the water is freed into drops of such size that they readily settle out. This action has been photographed by the micro-moving-picture camera; under the microscope, the breaking-up of the emulsion, as described, is seen to be accomplished in a few seconds. The low power requirements of the process, from records of commercial plants, substantiate the theory that the action is that of a multitude of electrical condensers in series, rather than that of a number of conducting paths. The minute water particles serve as the metallic elements, or plates, of the condensers and the separating oil acts as the dielectric. Such surface charges as the particles may have are removed, and the intervening oil is broken, probably electrically by the voltage and mechanically by the attractive force between adjacent oppositely electrified particles. The principle of breaking up an emulsion under the influence of an alternating electric field was discovered by F. G. Cottrell and Buckner Speed, through experiments conducted, at the University of California, which resulted in a plant being installed on the property of the Lucile Oil Co. in the Coalinga field, California, early in 1909. This plant was able to reduce 14-per cent. emulsion to less than Pper cent. with commercial success. Standard Cottrell Apparatus The present standard Cottrell apparatus consists essentially of the electric treater and a settling or trap tank. The treater is a galvanized-iron tank approximately 3 ft. in diameter and 10 ft. high, which con-

Jan 1, 1924

By Charles E. Glass

A steadily growing body of evidence indicates that earthquake ground motions can cause failure of rock slopes that are otherwise stable under static loading conditions. As a result, the economic optimum working slope angle is reduced when earthquake shaking is considered in surface mine design, especially in regions of high seismicity. When designing surface mine slopes to withstand seismic motion it is as important to consider the probability of experiencing various levels of ground shaking as it is to consider the characteristics of the ground motion. For most slope designs, simple probabilistic techniques such as extreme value or maximum likelihood techniques are appropriate. These techniques, however, should be applied in such a way that a probability value is assigned to characteristic ground motion parameters at the mine rather than to nearby earthquake magnitudes. Several techniques have been developed to analyze rock slopes subjected to dynamic loads. Most of these techniques do not adequately account for the ground motion parameters of concern. The best technique appears to be one that utilizes actual earthquake time histories. A simple technique that calculates block displacement for any input accelerogram, using a linear acceleration approximation between time steps, has been developed that accurately accounts for rock block response. Results using this technique indicate that the following factors are important for assessing rock slope stability in earthquake regions:

Jan 1, 1983

By Harold A. Linke

THE following article presents notes and data compiled and computed by the writer for use in the determination of: size and slope of mill launders, details of junction boxes and downspouts, and distribution of pulp. It also includes pulp formulas, volume of discharge through bushings, paths of discharging streams, banking of turns and curves. In the design of a concentrating mill, the draftsman usually considers launders to the extent of providing ample "head" for transmission of pulp from one department of the mill to another. The superintendent of construction aims to build his launders wide and deep, and on a slope steep enough to ensure positive flow. So launders are laid generally on too steep a slope, with the result that the repair gang works to maintain launder bottoms and sides against the erosive action of the conveyed pulp. To this end many kinds of liners have been devised: concrete, mastic, white iron, glass, rubber. True, the reduction of slope to the point where a pulp will flow with minimum wear, will minimize labor and expense; but when the desired slope is not predetermined, the millman hesitates to readjust his launder slopes by cut-and-try methods. To the end that the desired size and slope may be found readily, the writer has: (1) conducted experiments with pulps of different specific gravity, screen analysis and dilution; (2) gathered a few graphic data from standard reference works (such as Peele's Mining Engineer's Hand- book and Taggart's Handbook of Ore Dressing); (3) computed several tables; and compiled results that have proved dependable for Utah Copper ore. It is quite possible that the following tables and graphs may not be applicable to all ores, but it is hoped that they may prove helpful, even in slight degree, in alleviating a portion of the trouble and migraine of some other millman.

Jan 1, 1939

By Harold S. Morgan

INTRODUCTION The Waste Isolation Pilot Plant (WIPP) is being developed in southeastern New Mexico by the United States Department of Energy as a research and development (R&D) facility to demonstrate the safe disposal in salt of radioactive wastes resulting from defense activities. As part of the WIPP R&D program, a series of in situ tests will be performed to determine the behavior of drifts and storage rooms in the creeping salt medium (Matalucci, et al. 1982). Data obtained in these tests will be used to evaluate and improve numerical models used to compute the structural response of these drifts and rooms. Stress has been proposed as one of the parameters to be measured in the tests, and borehole inclusion stressmeters have been included in the instrumentation package. Cages of this type provide an indirect measurement of stress change in that they actually monitor borehole displacements which are then related to changes in the in situ stress away from the borehole. The relationship between stress and displacement is highly dependent upon the constitutive behavior of the rock in which the gage is emplaced. This relationship is well understood for rocks with linear stress-strain behavior (Fossum, et al, 1976), but, for creeping rocks like salt, the relationship has yet to be determined. Thus, inclusion gage response in salt must be investigated fully before stress measurements from the WIPP in situ tests can be used for comparisons with computed stresses The calculations presented in this paper were performed as part of an investigation of inclusion stressmeter performance in salt. They focus on the strain gaged stressmeter (SGS) (Cook and Ames, 1979) and on a hypothetical solid cylindrical inclusion with variable stiffness Issues addressed include the effects of creep and the effects of gage stiffness on stressmeter output for various loading conditions. The

Jan 1, 1984

By AIME AIME

TRAINED as a mining engineer and with no little experience in the field of mining, his interests and activities later transferred to the alloying, fabrication, and physical metallurgy of nonferrous metals, principally silver, Robert H. Leach represents in his professional life both of the major phases of the fraternity of mining and metallurgical engineers. In his personal characteristics, his wide circle of true friendships, his kindly, sympathetic interest in the problems of his fellow engineers, be they the junior men of the mineral industries or the mature and experienced men, he typifies the characteristics and attitude so desirable in the professional man.

Jan 1, 1939

By Raymond C. Johnson

GASIFICATION is important to the anthracite industry, as it is to the entire solid-fuel industry and to the nation. However, to the anthracite industry it may have particular significance in that it would increase the market value of many millions of tons of a by-product fuel, which the industry now has in storage and is currently producing, in addition to increasing the potential market for all its products. The by-product fuel is of usable quality but the ash content is higher than it can be in other products and therefore it must be converted or used at the point of production. Gasification is one method by which the product may be given increased value. The inherent characteristics of anthracite make it well suited for producing a fuel or synthesis gas. It is the most concentrated form of natural commercial carbon, noncaking and noncoking; it does not produce smoke, tar, or soot and has a low sulphur content; and the volatile matter, which ranges between 2 and 8 pct, is 80 to 85 pct hydrogen with small amounts of methane, carbon dioxide, carbon monoxide, and nitrogen. The ash fuses at high temperatures, which allows it to be burned at high rates without slagging. However, with the addition of small amounts of dolomite, the ash will form a slag, or glass, which is very fluid. Anthracite has long been used in the manufacture of city gas and it is extensively used in various parts of the country to make water gas to be converted to hydrogen. Buckwheat and rice anthracite are used in Galusha producers to make producer gas. Excellent synthesis gas has been made in a Galusha producer with rice and barley anthracite with oxygen in tests at the Consolidated Mining and Smelting Co., Trail, British Columbia. In these tests, anthracite was shown to have advantages over competitive fuels, in that the gas had a higher hydrogen content and could be cleaned with less difficulty. The anthracite seams are steeply pitching and in mining the parting strata and some of the roof and bottom materials are taken with the coal. In preparation, these materials are separated by gravity from the commercial product and stored in refuse banks. This refuse contains a mixture of rock, slate, or shale, and high-ash anthracite with bone coal, which is low-ash coal that is interspersed with thin bands of shale. The bone coal contains between 25 and 50 pct ash with an average ash content of approximately 30 pct, with a

Jan 1, 1953

By R. C. de Lange

An improved replica technique is developed for a nondestructive study of the nucleation and growth of fatigue cracks. Three different growth stages of a fatigue crack were observed. An initial stage of high growth rate is followed by a long period of very slow growth, until finally a third period of high growth rate leads to fracture. THE metal-fatigue process is of a very complex nature. The experimental approach towards fatigue is susceptible to many minor influences which, together with the unavoidable scatter in testing results, makes the interpretation a matter of extreme care. The generally accepted fact that, in a homogeneous material, the fatigue cracks start at a free surface indicates that surface studies may contri-but in an essential way to a better understanding of the fatigue mechanisms. Indeed metallographic observations of the fatigue phenomena have been very fruitful in the last decade. The study of extrusions, intrusions, and persistent slip bands has contributed much to the present knowledge of the early processes in fatigue.' The drawback of the current metallographic techniques lies in the fact, however, that either observations of fatigue phenomena had to be made in a destructive way after an only partly executed test or a sequence of observations on the same test bar was only possible on notched specimens.2 4 In both cases an uncertainty exists as to the nucleation and growth of the fatigue crack in an unnotched test bar, where the crack can start at any place of a large area and develops in a test bar, which is macroscopically

Jan 1, 1964

By AIME AIME

FEW men are better known in fuel engineering circles in the Middle West than the present Chairman of the Coal Division of the A.I.M.E. - Julian Elnathan Tobey. Now vice-president in charge of engineering of Appalachian Coals Inc., of Cincinnati, he has served that pioneer regional marketing agency since Aug. 1, 1934, when he became manager of its engineering department. His duties have included field promotion work in the interest of use of the agency's coals from eastern Kentucky and Tennessee, south western Virginia, and southern West Virginia in new plants of all types. He has been especially interested in certain industries which have shown an alarming tendency to change to natural gas or hydroelectric power; also in the development and practical application of small stokers and other mechanical equipment.

Jan 1, 1941

By A. S. Bower

Any process which has for its object the preservation of iron and steel from rust, and which will make these metals more applicable than they now are to the requirements of mankind, will be sure to meet with attention from members of this association, and from all those who are either engaged in the extraction of the ore, its reduction to metal, or the subsequent application of the metal itself. It is, perhaps, not too much to say that when iron and steel are rendered secure against corrosion and decay, they will be used to an indefinitely greater extent than they now are. The whole realm of science has, therefore, been explored in the attempt to discover some method by which the formed article may be preserved, leaving its strength undiminished by the destructive action of rust. Paints, oils, varnishes, glazes, enamels, galvanizing, electro-depositing and what is called "inoxidizing" are among the many systems now in vogue to effect the preservation of iron and steel from the corrosive action of air and water. The object of this paper is to show what may he done in protecting iron and steel from rust by forming upon their surfaces a film of magnetic oxide by an inexpensive process. It is no new thing to be told that magnetic oxide of iron is unaffected by exposure to the atmosphere or to salt water for any length of time. The black sand of Taranaki, in New Zealand, is a sufficiently good example of this. Dr. Percy has pointed out that the reason why Russian sheet iron is less affected by exposure than ordinary sheet iron is because of a coating of magnetic oxide; but this was not known

Jan 1, 1883

By P. A. Tucker, T. B. Rhinehammer, D. E. Etter, J. E. Selle

The Ce-Cu phase diagram was investigated by differential thermal analysis and rnetallography. Two congruent melting compounds, CeCu2 (817°C) and CeCua (938°C), and three incongruent cornpounds, CeCu (516°C), CeCu, (796°C), and CeCu, CERIUM and copper have been suggested as possible diluents in a liquid-plutonium fueled reactor. As part of the determination of the Ce-Cu-Pu ternary phase diagram, a review Of the Ce-Cu system (798°C), are present in this system. Eutectics exist at 28 at. pct Cu (424°C), 74 at. pct Cu (756°C), and 91 at. pct Cu (876°C). The purity of the cerium used has an important effect on the results obtained by differential thermal analysis. was considered necessary. Previous work by Hanaman was conducted with relatively impure metal: 96.7 pct Ce with 2.5 pct other rare earths and 0.5 pct Fe as major impurities. The metal had a melting point of 715°C as compared to the melting point for pure cerium of 804°C as reported by Spedding and Daane.2 Results presented in this work were obtained primarily by differential thermal analysis (DTA) and metallographic examination of slow-cooled or quenched samples.

Jan 1, 1964