Search Documents

By Jacob T. Wainwright

This stove has been designed to meet the requirements of a fur nave that must be operated with either a reducing or a neutral flame ; and more particularly to make feasible the operating of re duction-furnaces with the cheaper grades of gas-fuel, which has heretofore been impracticable. In general, cheap gas-fuels result from incomplete combustion, and, being suited for further combustion, answer very well for heat ing purposes; and high temperatures may be attained with them, when they are used in conjunction with regenerative stoves. But, in operating a reduction-furnace, a high temperature is not the only requirement. It is also necessary that the fuel shall not be cansumed beyond a certain degree, in order to insure a re ducing flame for the reduction-process ; consequently, it becomes necessary to dispense with combustion as much as possible previous to the use of the fuel-gases in the reduction-furnace. Moreover, these gases must be preheated to a high degree, in order that a sufficient temperature may be maintained in the furnace; and, since this preheating cannot be accomplished by a previous, partial combustion of the gases themselves, it follows that the stoves for pre heating these gases should be heated to as high degree as it is pos sible to attain with an inferior fuel. This result can best be accom plished by complete combustion of the heating gases, and is further facilitated by preheating all of the air and gas used for this com plete combustion. It is more particularly desirable to preheat the air, since the combustible gases used may generally be obtained directly from the furnace, or gas-producer. The reducing gases, escaping from a gas-fuel reduction-furnace, are capable of considerable further dilution with air to secure com plete combustion, and consequently may be utilized for heating the stove to a high temperature, provided the air be sufficiently preheated.

Jan 1, 1889

By Norman D. Fitz Gerald

THE growth of domestic requirements for motor fuel has been phe-nomenal, rising year after year in a fashion almost unique among com-modities, resisting depressions and forging rapidly ahead in times of prosperity. Consumption advanced from 226 millions of barrels in 1925 to 522 millions of barrels in 1938; or 130 per cent. The economic influ-ences generating and sustaining this demand are of vital concern to the petroleum industry. The general factors affecting utilization of motor fuel are well known but it is the purpose of this paper to employ the recently developed technique of economic dynamics to describe them mathematically. Such problems in economic analysis are complicated by the freedom of all the variables to fluctuate, their mutual interdependence, changing incidence upon one another, and the nonquantitative character of some of them. Economic quantities and relationships, unlike those of the physical world, are continuously changing and this dynamic characteristic is both a distinguishing and confusing feature in economic research. The com-plexities of the problems require application of the analytical devices of mathematical statistics to uncover the probable relationships between factors. The procedure employed is to formulate a logical relationship linking the dependent to the independent variables, and then simul-taneously, rather than sequentially, determine their separate effects by multiple correlation. This transformation of common knowledge to quantitative terms makes it possible to measure the probable effects of changing conditions upon requirements, assisting in the sound interpreta-tion of economic policies. The utility of the results of such dynamic analysis is in sharp contrast to the sterility of the trends and other simple empiricisms of descriptive statistics. It is not intended in this study to throw light on the reasons why any motor fuel at all is consumed; but to discover relationships explaining why more was consumed at one time than at another. Specifically the prob-lem is confined to the measurement of the influences of statistically

Jan 1, 1940

By George M. Fowler

MINING geology is a progressive study, so we must look to the future for the solution of many of its most significant problems. These problems, world-wide in scope, offer ample opportunity for the exercise of the utmost skill and intelligence by all that attempt to solve theta, as it is generally recognized that many ore deposits of the future will he found only by months or years of combined intelligent effort by the several engineering groups. Renewed appraisals are continually being made to better understand the relationship of physical-chemical processes to ore deposition and other mineralization and to interpret the findings of the geophysicists and others in terms of economic results. A study of current geologic activi¬ties clearly reflects the growing tendency for cooperation between the different branches of geology in order to appraise their united efforts. In line with these activities arrangements have been made to transfer the geophysical section of the U. S. Bureau of Mines to the Geological Survey.

Jan 1, 1936

By JOHN MARKLE

JOHN MARBLE, mining engineer, coal operator, philanthropist, member of the Institute since 1879, vice-president in 1903-04, has been paid the well deserved tribute of Honorary Membership. The presentation of the diploma was made at a luncheon in New York on Feb. 13, the citation reading: "In recognition of his work as an engineer and administrator of mines and his services to mining engineering education." Within the last month Lafayette University dedicated the new John Markle Mining Engineering Building, the gift of the eminent alumnus for whom it is named. In addition, Mr. Markle has contributed a maintenance fund for the carrying out of far-reaching plans for improving the mining courses to be given at the Institution. One of his theories is that quality rather than quantity of engineering graduates is the need of the profession. John Markle was born in Hazleton, Pa., in 1858. He received his degree of M. E. at Lafayette in 1880, and married Mary Estelle Robinson in New York City in 1884. Since 1880 he has been associated continuously with the firm of G. B. Markle & Co., and its successor companies. He has also been an official of numerous other important companies, although he is now retired from active business life.

Jan 1, 1930

By Paul M. Tyler

DOES mining pay? Inasmuch as the whining of minerals from Nature is one of the world's principal sources of new wealth, this question is of general economic interest but it is obviously of even more vital concern to investors and those engaged in mining. In a previous article on "Wage Costs in the Mineral Industries,' published in the November issue, I attempted to show that wages paid workers on the job accounted for, roughly, 50 per cent of the mine dollar. Salaries normally range over 5 per cent - lower for large metal mines but higher in stone quarries and minor nonmetallic min. in, industries. Purchases of supplies, materials. fuel, and power generally aggregate within the range of 15 to 25 per cent of total receipts, with the average well under 20 per cent. The total of all such specified expenditures which may he loosely described as

Jan 1, 1934

By S. H. Williston

IT not often that bore hole surveys can be checked by actual. civil engineering methods. A recent Arizona survey was checked by normal surveying methods and the comparison of the results should be of value to both oil and mining men. During the summer of 1948 the Phelps-Dodge Corporation, at its Copper Queen property near Bis-bee, Ariz., drilled a 1245 ft, 8 in. diarn, churn drillhole in a mineralized area and cased part of it, intending to use it to transfer mill tailings for stope fill. The hole, as frequently occurs, was not straight, and, in endeavoring to locate the bottom in the underground workings, they found no evidence of the hole at the underground coordinates directly below the surface location. The noise of the drilling tools was reasonably clear, but the direction of sound was uncertain. Preliminary tests with available equipment were not successful in locating the bottom of the hole. Because of the mineralized character of the area and the fact there was some casing in the hole, any magnetic method of well surveying would give results of doubtful value. Sperry-Sun gyroscopic well-surveying instruments were finally used to locate the bottom of the hole. These instruments consist of a gyroscope to determine azimuth and either a pendulum or bubble inclino-meter. A multiple shot camera photographs both instruments on a single film and superimposes the photograph of a watch. Coordination of depth with time at the surface makes it possible to select the corresponding picture for any depth. After making several runs of the empty instrument housing from the top of the hole to the bottom to make sure there were no obstructions in the hole, three surveys on wire line were completed during the afternoon. The three surveys, in which readings were taken at different points in the hole on each survey, were computed and gave the following locations of the bottom of the hole in relation to the surface collar: survey No. 1—24.92 N, 30.30 W; survey No. 2—24.24 N, 31.11 W; survey No. 3—26.54 N, 27.72 W. Then the data from the three surveys were combined into a single set of calculations which gave a location for the bottom of the hole: combined surveys—24.27 N, 30.16 W. (Fig. 1.) Immediately upon the determination of the coordinates at the bottom of the hole, a drift on the 1300 ft level was started toward the indicated loca- tion some 38 ft northwest of the coordinates of the surface location, The bottom of the hole was located within the drift round in which it was expected, and the transit survey run to the actual location of the hole indicated N 27.18, W 29.71. This shows a discrepancy between the well survey and the transit survey of 0.45 ft in the westerly direction and 2.91 ft in the northerly direction. All surveys, both gyroscopic and transit, fell well within the width of an ordinary drift. While this is satisfactory for almost any and all mining requirements, a theoretical examination was made as to reasons for the discrepancy. A study of the course of the hole indicates that considerable right turn or spiral existed, and in all probability the surveying instrument was pulled out of alignment while traversing the turn by approximately 0.05 ft at the top and another 0.05 ft in the opposite direction at the bottom of the instrument. If such an allowance were to be made, the survey calculations would almost exactly correspond with those determined by transit. This sort of discrepancy would be minimized by the use of stabilizing guides. It is unfortunate that physical laws probably effectively prevent the use of gyroscopic instruments in EX and AX diamond drill holes. The directive power of a gyroscope falls off inversely at some rate between the third power and the sixth power of the diameter. Present instruments can be run in casing 53/4 in. ID or over and might be adapted to somewhat smaller diameters, but the difficulty of reducing these diameters to 11/4 in. or 2 in. is almost insurmountable at the present time. Acknowledgment The author wishes to express his appreciation to the Phelps-Dodge Corporation for permission to publish this article, and to the Operating and Engineering Departments for their cooperation on the survey; also to Donald Hering, of the Sperry-Sun Well Surveying Co., who actually made the survey and calculated the results.

Jan 1, 1951

By S. H. Williston

IT not often that bore hole surveys can be checked by actual. civil engineering methods. A recent Arizona survey was checked by normal surveying methods and the comparison of the results should be of value to both oil and mining men. During the summer of 1948 the Phelps-Dodge Corporation, at its Copper Queen property near Bis-bee, Ariz., drilled a 1245 ft, 8 in. diarn, churn drillhole in a mineralized area and cased part of it, intending to use it to transfer mill tailings for stope fill. The hole, as frequently occurs, was not straight, and, in endeavoring to locate the bottom in the underground workings, they found no evidence of the hole at the underground coordinates directly below the surface location. The noise of the drilling tools was reasonably clear, but the direction of sound was uncertain. Preliminary tests with available equipment were not successful in locating the bottom of the hole. Because of the mineralized character of the area and the fact there was some casing in the hole, any magnetic method of well surveying would give results of doubtful value. Sperry-Sun gyroscopic well-surveying instruments were finally used to locate the bottom of the hole. These instruments consist of a gyroscope to determine azimuth and either a pendulum or bubble inclino-meter. A multiple shot camera photographs both instruments on a single film and superimposes the photograph of a watch. Coordination of depth with time at the surface makes it possible to select the corresponding picture for any depth. After making several runs of the empty instrument housing from the top of the hole to the bottom to make sure there were no obstructions in the hole, three surveys on wire line were completed during the afternoon. The three surveys, in which readings were taken at different points in the hole on each survey, were computed and gave the following locations of the bottom of the hole in relation to the surface collar: survey No. 1—24.92 N, 30.30 W; survey No. 2—24.24 N, 31.11 W; survey No. 3—26.54 N, 27.72 W. Then the data from the three surveys were combined into a single set of calculations which gave a location for the bottom of the hole: combined surveys—24.27 N, 30.16 W. (Fig. 1.) Immediately upon the determination of the coordinates at the bottom of the hole, a drift on the 1300 ft level was started toward the indicated loca- tion some 38 ft northwest of the coordinates of the surface location, The bottom of the hole was located within the drift round in which it was expected, and the transit survey run to the actual location of the hole indicated N 27.18, W 29.71. This shows a discrepancy between the well survey and the transit survey of 0.45 ft in the westerly direction and 2.91 ft in the northerly direction. All surveys, both gyroscopic and transit, fell well within the width of an ordinary drift. While this is satisfactory for almost any and all mining requirements, a theoretical examination was made as to reasons for the discrepancy. A study of the course of the hole indicates that considerable right turn or spiral existed, and in all probability the surveying instrument was pulled out of alignment while traversing the turn by approximately 0.05 ft at the top and another 0.05 ft in the opposite direction at the bottom of the instrument. If such an allowance were to be made, the survey calculations would almost exactly correspond with those determined by transit. This sort of discrepancy would be minimized by the use of stabilizing guides. It is unfortunate that physical laws probably effectively prevent the use of gyroscopic instruments in EX and AX diamond drill holes. The directive power of a gyroscope falls off inversely at some rate between the third power and the sixth power of the diameter. Present instruments can be run in casing 53/4 in. ID or over and might be adapted to somewhat smaller diameters, but the difficulty of reducing these diameters to 11/4 in. or 2 in. is almost insurmountable at the present time. Acknowledgment The author wishes to express his appreciation to the Phelps-Dodge Corporation for permission to publish this article, and to the Operating and Engineering Departments for their cooperation on the survey; also to Donald Hering, of the Sperry-Sun Well Surveying Co., who actually made the survey and calculated the results.

Jan 1, 1951

By Roland J. Lapee

A history of the progress made in copper refining in Montana is presented. The casting furnaces and the newly rebuilt electrolytic refinery are descmbed and operating details are given. Experiences with various addition agents, effects of rernoval of chlorine from the electrolyte, and effects of separan on electrolyte and on copper deposit are discussed. Observatzons are made on the effect of various impurities in anode copper and behavior of thezr salts in electrolyte and in slime, on treatment of slime for removal of copper, and on electrolyte puriification problems. The improved method for production of starting sheets is described. Attention is given to new materials for construction and to improvement in matrials handling ad quality control. COPPER refining at Great Falls, Montana, dates back to 1892. The original plant produced 65,000 lb. of cathodes per day at a current density of 16 amp per sq ft. In this plant anodes and cathodes were handled to and from the cells by means of hand-operated chain blocks and were moved about the plant by hand trucks. Cathodes were melted in coal-fired, reverbera-tory furnaces, were charged by hand, and refined copper was dipped by hand and cast in iron molds. In 1916, a new, modern plant with capacity to refine 18 million Ib. copper per month was built. Two refining furnaces were built, and each was provided with a twenty-mold Clark casting wheel. In 1922, the furnaces were converted to the use of pulverized coal: in 1923, to the use of oil; and in 1928, to the use of natural gas. In 1926, the plant was enlarged 50 pct. The use of pulverized coal for refining copper at Great Falls was discussed1 in a paper presented at the Salt Lake City meeting of the Institute in September 1925. Also, a comparison of the use of various fuels in copper refining furnaces was discussed 2 in a paper presented at the New York meeting of the Institute in February 1932. Prior to 1943 the cellroom was operated with twenty-five 720-lb. anodes and 26 cathodes per cell. Four cathodes, each weighing about 165 lb., were produced from an anode. In 1943 the weight of the anode was reduced to 460 lb., and two cathodes, each weighing about 190 lb., were produced from an anode. In 1949, a Billet Casting Wheel for the production of 3 in. diam phosphor deoxidized billets was built. A paper, presented at the New York Meeting of the Institute in February 1956, describes3 this plant and operation. In the electrolytic refinery, production is controlled by variation of the current density. In 1956, germanium rectifiers on a separate electrical circuit were provided for the starting sheet section so that current density could be maintained at any desired figure. Also in 1956, a program of modernization and enlargement of the Electrolytic Copper Refinery was started. This program, when completed, will raise the capacity of the Great Falls Electrolytic Copper Refinery approximately 33 pct, to 33 million lb. of cathodes per month. Furnace capacity for melting cathodes and anode scrap is ample to take care of the increased production from the electrolytic refinery. This fortunate condition came about primarily as the result of the three following changes: 1) The furnaces were lengthened 10 ft in 1922 when the fireboxes were found unnecessary for burning powdered coal. 2) Furnace life, and hence furnace capacity, was increased by the successful efforts of the Copper Refinery staff to develop a method for sanding furnace side walls and roof. 3) The natural gas being used has a very low sulfur content. As a result, it is possible to reduce time spent rabbling and poling and thus greatly increase tons per furnace charge. TANKHOUSE AND TANKS The Great Falls Electrolytic Refinery is 535 ft long by 252 ft wide. The cells are arranged in four crane bays in which are operated seven 10 ton Whiting Cranes. The old cells are in groups of ten, with circulation of electrolyte through five cells in cascade and with aisles between the groups of ten cells. The new cells are nested in groups of sixteen with no aisles, are all on one level, and have individual circulation to each cell. Present plans call for 1792 commercial cells and 128 stripper cells. To reduce confusion during the construction period, and to use the cranes, cars, and other equipment already on hand, the cells in the rebuilt section were designed to have approximately the same inside dimensions as the cells in the old part of the

Jan 1, 1962

By M. H. Yoo

Possible interactions of the perfect dislocations of six slip systems or the c dislocation with the (10i2f (ioii), {ioIi}(ioiZ), {1122}(1123), and {1121}(ii26) type twins in hcp metals have been analyzed from the crystallographic and the energetic points of view. Twenty-six distinct types of possible interactions were identified, and those selected based on crystallographic constraints were examined for their energetic feasibilities by use of the anisotropic energy factors. No long-range elastic interaction exists for a dislocation when its Burgers vector is parallel to the twin interface. Under a suitable applied stress, a screw dislocation can cross slip at the twin interface. For basal mixed dislocations in cadmium and zinc, the interaction with {1012} twins is found to be attractive, indicating that incorporation of these dislocations into the twins is energetically feasible and that twin growth will result. On the other hand, the interaction between both basal and Prism mixed dislocations and the {1012} and (1121) twins is found to be repulsive in Mg, Co, Re, Zr, Ti, Hf, and Be. This indicates that under an applied stress a local stress concentration will develop due to a dislocation pileup at the interface, which may result in a site for either the nucleation of other twins or the formation of a crack, depending on the cleavage strength. WHEN a metal undergoes plastic deformation, a certain configuration of slip dislocations will result in a state of dislocation pileup against an obstacle. The stress concentration thus developed may enhance the process of twin nucleation and also twin growth. Furthermore, once formed and dispersed in the crystal, twins can act as effective barriers against slip dislocations. The degree of such mutual influence or interrelation between slip and twinning is generally known to be pronounced in the case of hcp, metals. It is also known that deformation by twinning occurs more commonly in hexagonal metals than in cubic metals. In fact, under suitable stress states, all hexagonal metals exhibit {1012) <1011> type twinning.&apos; In addition to this common type, deformation by (1151) <1126> type twinning occurs in zirconium, titanium, and rhenium, which show remarkable ductility.&apos; The importance of twinning during general deformation to the ductility of hcp polycrystals has been briefly discussed in recent review works.2&apos;3 The purpose of this paper is to analyze the interaction between slip dislocations and twins in the hcp structure and to discuss the nucleation and growth processes of twinning and the role of twinning in the <"°" noil) o, 1/3[112O] (OOO2) 1/3[1123] Fig. l—-Slip systems in hcp structure. ductility of hexagonal metals. The problem will be discussed from the geometric and the energetic points of view in a manner similar to that of the previous work on zinc.4 Since hcp crystals deform by several slip and twin systems, numerous interactions result as possibilities. The Burgers vectors of six slip systems and the c dislocation shown in Fig. 1 and the four twin systems listed in Table I are considered here. A complete tabulation of the possible interactions is followed by discussion of those that are more likely to occur on the basis of crystallographic constraints and energetic considerations. 1) CRYSTALLOGRAPHY OF TWINNING The crystallographic elements, K1, K2, n1, and n2, for the four compound twin systems are now well established.= A unit cell with the base vectors n1, and n2 is shown in Fig. 2 for each twin system. The unit cell before twinning is shown in solid line, and the corresponding unit cell after twinning is shown in dashed line. Also shown in Fig. 2 are the following crystallographic parameters: S is the plane of shear, d the interspacing of the twin habit planes K1,Ø Iis the acute angle between n1, and n 2, e is a numerical factor, and q is the number of K, lattice planes intersected by 17&apos;. These parameters can be expressed in terms of the axial ratio, y = c/a, as listed in Table 11. The macroscopic shear strain of twinning, s, and the magnitude of a "unit twin dis-l~cation,"4 bt, are also expressed in terms of y and given in Table 11. In Table 11, K1 and q1 are given in both Miller-Bravais and Miller indices. In double lattice structures, shuffling of atoms in addition to a homogeneous shear of the lattice is generally required if the original crystal structure is to be restored after twinning. The extent of current understanding on this problem of atom shuffling is per- Table I. Four Twin Systems in Hcp Structure

Jan 1, 1970

By G. A. Swanquist, E. M. Morales

INTRODUCTION The idea of water management and control at the Church Rock Mill operations began to take shape in February 1979. At that time, we were already investigating the feasibility of decreasing the fresh water requirements so that the solids would become the limiting factor in tailings impoundment utilization. The area for solution evaporation could be kept at a fraction of the normal requirements under the standard process of full water usage. The Church Rock Mill is an acid leach circuit followed by solids/liquid separation with thickeners in counter current decantation, and solvent extraction. Following the normal design of acid leach circuits, reuse of tailings solution was not incorporated in the original mill process design. INITIAL WATER CONTROL INVESTIGATIONS The investigations to decrease the fresh water requirements centered around modifying the grinding circuit from the present semi-autogenous grinding (SAG) mill in closed circuit with hydrocyclones, to open circuit grinding with a rod mill. The open circuit grinding with the SAG mill and rod mill in series had the potential of decreasing the water requirements for grinding and leach dilution by approximately 50% or 1.4 m3/min (300 gpm). The grinding pulp density would be maintained at 70 to 72% solids, and the leach dilution to 50% solids would be accomplished with acid tailings liquor recycle. In such a grinding circuit arrangement, the SAG mill would provide the primary or coarse grind, and the rod mill would be used for the fine grind. By the SAG mill and rod mill series grinding method of water control and other secondary water controls in various places downstream from the grinding circuit, the required necessary evaporation area was estimated at 120 acres of liquid surface. A second method of water control at grinding was investigated. A two-stage cyclone classification circuit appeared to have a good potential of achieving the same water reduction at a much lower capital and operating cost. However, in retrospect, this would not have been a viable method since a high slime recycle load would have been established hindering classification. The use of reagents to neutralize the acid tailings solution was not considered seriously at that time, since it would have materially increased operating costs, although it would have also allowed more tailings solution recycle and consequently, less fresh water usage. However, with the tailings solution deposition area available at that time, it was not then necessary to incur the high cost of neutralization. The control expected by the series grinding of semiautogenous and rod mills would have been sufficient to maintain a water consumption/evaporation equilibrium well in line with the available land area. IMPLEMENTATION OF NEUTRALIZATION OPERATIONS During the summer of 1979, the UNC Church Rock Mill experienced a tailings dam breach which resulted in a prolonged mill shutdown. Upon resumption of operations at the end of October 1979, tailings deposition was restricted to a small portion of the tailings impoundment area. Figure 1 shows the general tailings area and the limits of the present deposition area in the central part including the borrow pits. These borrow pits had been excavated to provide materials for tailings dam construction. Immediately after resumption of operations, it became evident that it would be necessary to control the quantity of liquid to be evaporated because of the small confined area available for tailings solution deposition and to maximize the deposition time in the tailings area. The water control required had to be exercised on a large scale, and to be in operation as quickly as possible. An obvious solution was to reuse the tailings liquor in mill process. Immediate steps were taken to install the necessary equipment for tailings neutralization on an interim basis. Anhydrous ammonia was selected as the primary neutralization reagent since it was the quickest system that could be placed in operation. Previous laboratory tests indicated fair results with ammonia neutralization. Such a system required a minimum of installed equipment and handling. INITIAL NEUTRALIZATION OPERATIONS Actual neutralization operations began on November 26, 1979. The raffinate solution which normally would have been discarded was pumped to a 3.7 m (12ft) diam by 4.3 m (14ft) tank for reagent contact, see Figure 2. At this tank, anhydrous ammonia was added directly from the tanker trailers and controlled at pH 7.0 nominally. Agitation was provided by air sparging. The neutralized product formed a highly viscous slurry in the grinding circuit which resulted in pumping and cyclone classification problems.

Jan 1, 1982

By W. E. Rudolph, R. E. Baylor

DUE to its location in the Atacama Desert, one of the most barren of the earth&apos;s surfaces, Chuquicamata&apos;s water supply presents unusual problems. Yearly rain-fall averages less than one tenth of an inch at the plant. However, there are summer showers above 12,000 ft in the Cordillera to the east, the resulting run-off flowing through old river valleys buried beneath more recent volcanic formations, to be impounded within sediment-filled basins. This water emerges at springs where the outlets of these basins are blocked by lava flows, and here are formed the small streams which feed the only important river of the region, the Rio Loa. Chuquicamata&apos;s water is obtained from these springs and rivulets. [ ] The map above indicates four pipe lines from which potable and industrial water are supplied. Potable water, amounting to 4500 metric tons per day, is conveyed in the Toconce pipe line from springs 59 miles due east of Chuquicamata. This water is used not only for drinking, but also for boilers and other needs requiring high quality. For industrial water at the oxide plant, there are two 12-in. pipe lines from the Rio San Pedro, carrying a total of 17,000 metric tons per day of slightly brackish water. This water is at present used mainly for leaching and for hygienic purposes. Water Source Found For the present and future needs of the sulphide plant, it was calculated that at least 32,000 metric tons per day of make-up water would be required. For this purpose, a pipe line of 44 miles length was constructed to bring in the entire flow of the Arroyo Salado, one of the eastern tributaries of the Loa. The salt content of this water is so high (over 5000 parts per million of solubles, mostly chlorides) that it is highly detrimental to farming, and the Chilean Government had been studying projects to separate these waters from others of the Loa system in order to improve agricultural conditions in the fertile valley of Calama. So it happened that the Government was willing to award rights to the Arroyo Salado waters under agreement whereby the Mining Company removes waters from the Rio Loa system above Calama for all time. The outlet of these waters, after serving their purpose at the new concentrator and leaving the plant in tailing, is the Salar de Talabre, an old salt lake which presents fully ten square miles of surface to serve as an evaporating pan, the outlets having now been blocked by dams. Here the dry climate of Chuquicamata is a favourable factor, evaporation averaging slightly above 1/4 in. per day. The Toconce and San Pedro pipe lines have been functioning from 26 to 34 years, and through the use of special cleaning tools which were developed at the plant, as well as deaeration of the more active Toconce water, these pipes are now maintained at capacities which do not diminish as years go on. Constructing the Dam The Arroyo Salado pipe line design and construction involved certain special and interesting features, and inasmuch as this line and its intake works are solely for the needs of the new sulphide plant, more detailed description is given. The waters are impounded at a gravity dam constructed of concrete to a height of 100 ft above the river bed, keyed into the precipitous Dacite walls of the narrow canyon (barely 6-ft wide at the bottom, only 25-ft width at 50 ft above). A small secondary dam was built 100 ft down stream from the main dam, providing a pool of 15-ft depth to protect the main structure from flood flows over the spill-way during the rainy season. A system of four 36-in. syphons was designed for discharging these flood waters from the lower depths of the lake, in order to avoid eventual sedimentation behind the dam. The lake has a length of 3300 ft, and its water level is controlled by an adjustable spillway permitting draw-down of eighty inches, amounting to 41,000 metric tons of available capacity. This regulation is necessary because of wide fluctuations in stream flow between day and night due to freezing of feeders. During the construction of the dam the entire river flow was handled within a 36-in. pipe line some 2000 ft in length. As the excavations proceeded

Jan 1, 1952

By G. M. Willis, F. L. Hennessy

The oxygen pressure in equilibrium with silver and Ag2O-B2O3 melts has been measured between 800&apos; and 900°C, to obtain the thermodynamic properties of the liquid. The compound Ag20. 4B20:1 appears to exist in the liquid, which shows marked heat content and entropy effects. A KNOWLEDGE of the thermodynamic properties of binary liquid silicates, borates, and phosphates would be of considerable assistance in the interpretation of the behavior of multi-component metallurgical slags. However, the literature contains comparatively few studies of the thermodynamics of binary slags. The system Ag20-B,O, attracted our attention as it was known to give a single liquid phase,&apos;,&apos; in which high contents of silver could be obtained (up to 61 pct Ag according to Foex2). Further, it would be expected that the partial pressure of oxygen over melts in equilibrium with metallic silver could be used to determine the activity of Ag2O in the Ag,O-B,O, system. In many respects, it may be expected that the reaction of a basic oxide with boric oxide would be analogous to its reaction with silica. Liquid immiscibility frequently occurs in both borate and silicate systems. With B2O3 and SiO reaction with a basic oxide presumably involves a breakdown of the three-dimensional network of the acid oxide by reaction with oxygen atoms common to more than one silicon or boron atom. Ag2O-B2O3 was therefore investigated as a model of a slag system in the hope that its thermodynamic properties would assist in understanding those of other systems. Several methods for determining the activity of a component in a slag have been described in the literature. Chang and Derge" used high temperature electromotive force measurements to obtain the activity of SiO2 in CaO-SiO2 and Ca0-Al203-Si02 slags, but the cell reaction in their work is not clear. low has used rate of volatilization and vapor pressure measurements combined with phase diagrams to obtain activities in the systems KO-SiO,, Na,O-SiO, and Li,O-SiO," and PbO-SiO26 Taylor and Chipman7 extrapolated their results for the distribution of FeO between liquid iron and CaO (+Mg0)-FeO-SiOl slags to obtain the activity of FeO in the binary FeO-SiO2 system. In principle, one of the most direct methods for obtaining the activity of a metallic oxide in a phase is by comparison of the equilibrium oxygen pressure for the system metal-pure oxide with that of metal oxide-containing phase. Schenck and othersa have studied the stabilization of Ag2O on combination with other oxides (MO,) in the solid state by measurements of the oxygen pressure in systems of the type Ag-Ag,O-xM0,-MOy-0, (gas). Schuhmann and Ensio" have determined the activity of FeO in iron silicate slags in equilibrium with solid iron, using CO/CO2 mixtures to establish known partial pressure of oxygen. Although the method gives the activity of FeO without ambiguity, the slag is not a binary system, and interpretation of the results in terms of the hypothetical binary system FeO-SiO, is not possible. If a metal is solid at temperatures at which the properties of the slag containing its oxide are to be studied, this method has the considerable experimental advantage that the metal can be used as the container for the slag, and contamination by contact with refractories is avoided. In this work, crucibles for Ag2-B,O, melts were made from silver, and the liquid brought to equilibrium with definite pressures of oxygen gas. The oxygen pressure PO, thus fixes the activity of Ag20 in the liquid silver borate. For the reaction at a given temperature. is substantially constant, is directly proportional to the square root of the equilibrium oxygen pressure. Varying the oxygen pressure changed the silver oxide content of the liquid and it was possible to obtain the activity of Ag2O over a range of composition. Experimental Procedure In principle, the method consisted of bringing melts in silver crucibles or boats to equilibrium at a fixed temperature under a definite pressure of oxygen and analyzing the glass after solidification. Materials: B2O3 glass was prepared from A.R. quality boric acid by fusion in platinum. The silver

Jan 1, 1954

By M. Bevis, A. F. Acton, P. C. Rowlands

Defor~nation twinning and transformation twinning modes most likely to be operative in Fe-Ni and Fe-Ni-C martensites have been determined using a new theory of the crystallography of deformation t~inning.~ This analysis shows that potentially important conventional and nonconventional twinning modes1 have been omitted in previous analyses. Discussion is given on the relevance of the predicted twinning modes to the lattice invariant shear associated with the martensite transformation in steels and to anomalous deformation twinning in Fe-Ni-C martensites. THE two most important criteria which appear to govern operative twinning modes in metallic structures1 are that the magnitude of the twinning shear should be small and that the twinning shear should restore the lattice or a multiple lattice in a twin orientation. The latter criterion ensures that the shuffle mechanism required to restore the structure in a twin orientation is simple. These criteria have been adhered to in the prediction of twinning modes2"6 in bcc and bct single-lattice structures with axial ratios in the range y = 1 to 1.09 as, for example, encountered in martensite occurring in steels. Refs. 2 and 3 in particular consider the martensite transformation in steels and the twinning modes in these cases relate to transformation twinning, and hence the lattice invariant shear associated with the martensite transformation. The list of twinning modes which can be compiled from these sources is incomplete and the ranges of magnitude of shear considered could be unrealistically small, particularly in the case of deformation twinning. The latter consideration is supported by the fact that twinning modes with magnitudes of shear large compared with the smallest shear consistent with a simple shuffle mechanism have been established in, for example, the single-lattice structure mercury7 and the multiple-lattice structure zirconium.&apos; In addition the anomalous deformation twins reported by Ftichrnan4 to occur in a range of Fe-Ni-C martensites still remain unexplained. It is clear that a comprehensive analysis of twinning modes likely to be operative in martensite In steels is required. The results of the application of a new theory of the crystallography of deformation twinningg to these structures are presented in this paper. The theory has been used to determine all shears which restore the lattice or a multiple lattice in a new orientation with magnitude of shear up to a required maximum. The orientation relationships between parent and twinned lattices are not restricted to the classical orientation relationships of reflection in the twin plane or a rotation of 180 deg about the shear direction. PREDICTED TWINNING MODES Twinning modes which restore all or one half of lattice points to their correct twin positions will be referred to as m = 1 and m = 2 modes, respectively. These modes are the most likely to describe operative modes in single lattice structures. The bcc m = 1 and m = 2 modes which have magnitudes of shear s in the range s < 2 and s < 1, respectively, have been given10 and are reproduced here in Tables I and 11. Detailed discussion of the crystallography of these modes and cubic modes in general will be discussed elsewhere (~evis and rocker, to be published). The four twinning elements Kl, &,ql,7)2 as well as the magnitude of shear s are given for each twinning mode, and the twinning modes are given in order of increasing shear. Two twinning modes are given in each row of the tables, the twinning mode Kl, Kz, ql, q2 and the reciprocal twinning mode with elements Kl = K,, Ki = Kl, q: = q2, and 17; = ql. The m = 1 and m = 2 twinning modes which describe twinning shears with small magnitudes of shear and simple shuffle mechanisms in bct crystals with -y = 1 to 1.09 are given in Tables I11 and IV, respectively. On increasing the symmetry of the tetragonal lattice to cubic, that is making y = 1, all modes listed in Tables 111 and IV must reduce to crystallographically equivalent variants of the modes given in Tables I and 11, respectively, or become twinning modes with both shear planes as symmetry planes in the cubic lattice and hence not considered in Tables I and 11. With the exception of this last type of mode only those tetragonal twinning modes which reduce to modes 1.1, 1.2, 2.1, and 2.2 of Tables I and I1 are considered in Tables 111 and IV. For values of y in the range -y = 1 to 1.09 the tetragonal modes and the corresponding cubic twinning modes have approximately the same magnitude of shear. The twinning modes listed in Tables 111 and IV are therefore by the criteria given above the most

Jan 1, 1969

F A. THOMSON, president of the Montana School of Mines, gave an interesting talk on mining schools of the past, present and his ideas of the future before a recent meeting of the Montana Section of the A. I. M. E. He covered the history .of the various mining schools and com- pared the three main types of schools; those attached to or forming part of an endowed college or university such, for example, as&apos; the Columbia School of Mines, the Mining Department of the Massachusetts Institute of Technology and the Mining Department of Stanford University. These resemble in a general way the second class, those attached to the state universities and colleges. The schools of this general type have had varied success.

Jan 1, 1928

(The following -list, contains the navies of those members of the Institute of whose connection with military service we have only recently become acquainted; it also includes the names of a few who have recently been promoted or transferred. A com-plete list was published in the Year Book, issued as a supplement of the Bulletin for March, 1918.) ADDICKS, LAWRENCE, Naval Consulting Board. ALINE, P. A., Camp Lewis. BARCUS, WALTER .J. E., Captain, Ordnance Department. BAUSH, JOHN R., Private, 1st Army Headquarters Regiment, Co. M. BENNETT, A. F., Lieutenant. BILLINGSLEY, PAUL, Engineer Officer, Aviation Section, Signal Officers&apos; Reserve Corps. BOOTH, L. E., Ordnance Department. BROWN, JAMES F., 2d, 1st Lieutenant, Ordnance Reserve Corps, A. E. F.

Jan 4, 1918

THE illustration below shows the design of the face of the clock to be erected as a memorial to the American engineers who gave their lives overseas in the World War. It will be placed in the tower of the library at Louvain, which has been rebuilt through contributions from America. Large clocks seldom have figures on their faces, and each hour on this one will be marked by a gold star, the four faces containing 48 stars, one for each State of the Union. Contributions toward the memorial have been received from every one of the States, and from Alaska and Hawaii as well, but additional subscriptions are invited by the Com-mittee which is arranging for the memorial.

Jan 3, 1928

By A. L. Engel

IN the treatment of complex ores by flotation, one of the most important steps is conditioning the feed. Conditioning primarily consists of the addition, in the grinding circuit, of an alkaline reagent, for example sodium carbonate, which neutralizes any acidity of ore and mill water, counteracts the effect of &apos;harmful soluble salts, disperses colloids, and provides the necessary alkalinity for the best metallurgical results. The several minerals of the ore should be put in such condition that they may be floated or rejected as desired, through the action of further reagents thereafter used.

Jan 1, 1932

By W. J. Parton

THE efficient recovery and preparation of small sizes of anthracite called No. 4 Buckwheat (3/3 2 by 1/3 2 in.) and No. 5 Buckwheat (1/3 2 in. by 0), present a difficult problem to the anthracite operators. In many instances preparation of these sizes, particularly No. 5 anthracite, is extremely inefficient. In many of the older preparation plants, inadequate facilities, and often none at all, were provided as an integral part of the plant for cleaning this fine anthracite. Consequently, much of the material smaller than s, 32 in. was discarded. As the demand for these sizes increased, facilities for preparing the fine sizes were often crowded into existing structures with consequent sacrifices of capacities and efficiency. In addition to this condition, the methods of preparing the finest sizes are being developed in an attempt to improve their efficiencies. Because the demand for small sizes of anthracite still is increasing, many operators would benefit by investigating and improving the cleaning equipment employed on these sizes.

Jan 1, 1949

By Steven Mitchell

BACKGROUND Homestake Mining Company began milling operations at the Bulldog Mountain Mine near Creede, Colorado in 1969. The Bulldog Mill, rated at 350 tpd, produces a bulk flotation condentrate assaying about 180 oz/T Ag and 20% Pb, from heads of about 16 oz/T Ag and 2% Pb. The circuit is straightforward with two-stage grinding to 1-5% plus 65 mesh, followed by rougher and cleaner flotation. Reagents used are Z-6, Z-11, Aerofloat 242 and Aero Promoter 404, with an Aerofroth 65-MIBC mixture for a frother. Additional information on the geology, mine and mill are available in references (1) and (2). A flow sheet for the mill and CIP plant together is attached as Figure 1. Final flotation tailings normally vary from 1.5 - 2.0 oz/T Ag. These tailings are cycloned to produce sand for underground backfill. After cycloning, the sands are repulped and given a final scavenger float. This sand scavenger recovers a small additional amount of silver which recycles back to the main flotation circuit. The tailings are recycloned and pumped to the mine or, if the mine cannot accept sand, to tailings. The majority of the silver in the flotation tailings exists in the fine fractions; cycloning upgrades the slimes and lowers the assay of the sand. The sand, after scavenging, typically assays 0.5 oz/T Ag, and the slimes assay about 3.0-3.5 oz/T Ag. From 1969 to 1976 all of the slime tailings and the sand tailings not used underground were impounded in a tailings pond located about

Jan 1, 1983

By R. L. Fullman

IN the investigation of metallurgical transformations and the relationships between microstructure and properties of metals, it frequently is desirable to obtain a measurement of the relative amounts of the various phases present and of the mean size of particles into which each phase is dispersed. The relative amounts of the phases can be measured by the classical methods of area, lineal, and point analysis,1-5 in accordance with the principle that the volume fraction of a phase, the fraction of a polished cross section occupied by the phase, the fraction of a random line occupied by the phase, and the fraction of randomly arrayed points occupied by the phase are all equal. The validity of this relationship depends only on the attainment of a truly random sample of area, length, or points, and not on the size, shape, or distribution of the particles constituting the phase. Smith and Guttman8 have derived a relationship between the interface area per unit volume S, and the measurable quantities L., the interface length per unit area on a cross section, and NL, the number of interfaces per unit length intersected by a random line. Their equation, Sv = — L8 = 2NL is also valid regardless of the distribution of particle sizes and shapes. In contrast to the situation concerning measurement of relative fractions of phases and of interface area, the measurement of particle sizes in opaque samples has not been subjected to a complete analysis. It has been common to measure some lineal or area dimension of particles on a polished cross section and to use the mean value as a qualitative measure of particle size. In the present paper, quantitative relationships are established among the various mean dimensions on a polished cross section and the actual dimensions of the particles present. Particles of Uniform Size Spheres: If a metal sample contains particles of a phase a dispersed in the form of spheres of uniform size, a polished cross section through the sample will reveal circular areas of phase a with radii from 0 to ?, the radius of the spheres. Consider a cube of unit dimensions to be cut from the sample. If a cross section parallel to one of the cube faces is examined, the average number of particles per unit area (N,) equals the number of particles per unit volume (Nv) times the probability p1 that the plane would intersect a single sphere positioned at random within the unit cube. Since, of the various possible positions for the cross-sectional plane over the unit length from top to bottom of the cube, only those positions existing over the length 2r would lead to the plane intersecting the sphere, the probability of intersecting a single sphere is just 2r. N8= Nvp1 = Nd-2r [1] Applying the equality of area and volume fractions, the relationship is found between sphere size and average area s of uniform spheres intersected by a random cross section, 4 - f = NV V = Nr . — pra = N s = Nd . 2rs S = —pr2 [2] A similar analysis reveals the average traverse length across spheres of uniform size when random lines are passed through the sample. If a randomly oriented unit cube is cut from the sample and a randomly positioned line is passed through the cube parallel to a cube edge, the number of spheres intersected by the line (Nl) equals the number of spheres per unit volume times the probability p1 of the line hitting a single randomly placed sphere in the cube. Since possible positions of the line occupy unit area, and possible positions for which it will pass through the sphere occupy an area of pr2, the probability of the line hitting a randomly placed single sphere is pr2. NL = Nv p1 = Nvpr2 [3] Combining this relationship with the equality of volume and lineal fraction, the desired relationship is obtained between radius and mean lineal traverse length -i, for spheres of uniform size. 4 - - 3 l=4/3r [4] Circular Plates: Consider a sample containing particles of a phase a in the form of circular plates of uniform radius r and thickness t, where r >> t. If the plates are randomly oriented, as in a sufficiently large sample of a fine grained polycrystalline material, area and lineal analysis may be carried out with parallel cross-sectional planes and lineal traverses. If the plates are not randomly oriented, it is necessary to randomize the orientation of the cross-sectional planes and traverse directions. Let a unit cube be cut from the sample, and a cross-section plane be passed through the cube parallel to one of the cube faces. The number of plates cut by the cross-sectional plane per unit area is equal to the number of plates per unit volume times the probability of a plate intersecting a single randomly positioned and randomly oriented plate in the cube. If J is the component of the plate diameter in the direction normal to the cross-sectional planes, the probability of a plane cutting a single randomly oriented plate is equal to J, the mean value of J for all possible orientations of the plate. Let 4 be the dihedral angle between a plate and the cross-sectional plane, and let p?, d? be the probability that a plate makes an angle between 4 and ? + d? with the cross-sectional plane. Then for ran-

Jan 1, 1954