Search Documents

By Eric Jette

IN order to control a chemical process by other than empirical, rule of thumb methods, two types of knowledge concerning the reactions involved must be available: (1) the thermodynamics of the reactions, and (2), by no means less important for efficient operation, the mechanisms and kinetics of the reactions. Information on the thermodynamic side enables the operator to decide upon initial and final conditions, whether heat must be .added or removed from the system, whether the reactions proceed farthest in the desired direction at high pressure or low, etc. Knowledge of the mechanisms involves the determination of the individual steps by which an initial set of reactants, under given conditions, proceed to give the desired final products and kinetic studies upon which the mechanisms are based give the speed at which each of these reactions or steps take place. Thus thermodynamic studies of a 'reaction enable the operator to control the direction and extent to which the reaction can proceed, while kinetic studies enable him to control rates and thus the time' efficiency of the operations. The thermodynamics set the limit to which the reacting system approaches; the kinetics tell how fast the system actually approaches this limit. The two types of information are complementary and not antagonistic even though in discussing the mechanism the introduction of thermodynamics is entirely needless and generally of no assistance, while in thermodynamic studies mechanism need not even be mentioned.

Jan 1, 1931

By P. E. Baker

Approximate solutions are presented for the heat-flow equations in a loss-free linear system with a moving source and with heat transfer by convection and conduction, representing in situ combustion in an oil reservoir. The rate of heat generation and the velocity vf of the source (flame front) are assumed constant. A cold front or convection front caused by the cooling effect of in-jected air develops behind the flame front and moves with velocity vc, which is determined by the thermal properties of the air and rock. Because of thermal conduction the fronts are not sharp; i.e., they do not represent temperature discontinuities. The following solutions apply after a sufficiently long time. where Q is heat generated per unit volume of formation, k is thermal conductivity, CF is volumetric heat capacity, a is thermal diffusivity, and subscripts 1 and 2 refer to values behind and ahead of the flame front, respectively. The parameter CF2 is contained in v . Te is initial reservoir temper- . C2 e ature and air-injection temperature. Other mathematically possible solutions are presented. The different solutions result from the use of different values for various physical parameters. The solution just presented is thought to be most commonly applicable. INTRODUCTION In this paper, approximate analytical expressions are derived for the temperature profile developed in the underground combustion method of oil recovery. A qualitative description of the process may be found in a paper by Tadema.1 The flame front is regarded as a moving source with a constant rate of heat generation. Heat transfer is by conduction and convection. Previous publications, of which a few are cited here, 2-5 have also attacked this problem and have presented solutions pertaining to different methods of approximating or idealizing the process studied. The present paper also treats an idealized case: linear flow is assumed for heat and fluids, and vaporization and condensation effects are neglected. The results obtained are similar to those derived by Bailey and Larkin,3 but are obtained by an entirely different procedure. The method used here should give considerably greater insight into the physics of the in situ combustion process. Four types of cases are considered, distinguished by thermal and fluid-flow properties of the system. A constant rate of heat generation and constant rate of flame-front advance are assumed. Flame-front temperature is determined for each case using a heat balance which involves the entire temperature profile. The applicability of the different solutions to real systems is discussed after they are all presented. Again, this is done for the purpose of understanding better the physics of the process. Consideration of the nonapplicable solutions and of the reasons for their not applying is significant. In a paper by Cooperman,4 the only case solved is one considered here as not applicable. Fluid flow, as such (pressures, saturations, oil recovery, etc.), is not treated. This subject has been covered in a paper by Wilson, et al.6 Also, we are not concerned with requirements for continuance of the process; we only attempt to determine the temperature history for cases where the process has continued for some time. PHYSICAL SYSTEM AND APPROACH TO PROBLEM A linear flow (heat and fluid) system is assumed and the x-axis is taken parallel to the flow direction. The combustion zone (flame front) is vertical,

By T. D. Thomas

CONTENTS PAGE T. D. Thomas-Misfires in Anthracite Coal Mines 3 W. H. Forbes-Misfires in Bituminous Coal Mines 12 A. W. Worthington-Misfires in Non-metallic Mining (Limestone) 18 Misfires in Anthracite Coal Mines BY T. D. THOMAS,* LANSFORD, PA. (New York Meeting, February, 1929) IN THIS paper, major attention is given to misfires in mines where electric multiple shot-firing is the system used. Misfires are sometimes caused by one action or condition and at other times by a combination of two or more. They may be divided into two classes: (1) those caused by workers in the mines, (2) mechanical or manufacturer's causes. The second cause will be discussed first. MISFIRES CAUSED BY FAULTY DETONATORS The important part of an electric blasting cap, to the user where multiple shot-firing is done, ass in the steep-pitch, thick-vein, anthracite mines, is the bridge wire. In single shot-firing this factor is not apparent, but in mines where multiple firing is done any variation in the resistance of the bridge wire, where full or even rated battery capacity is required, will most likely cause a misfire The reason for this is obvious. If the resistance in the bridge wires is not the same, some of the detonators will fire because of their greater comparative resistance. Variance in resistance of bridge wires is caused by a slight difference in the diameter of the bridge wire, also to a difference in the composition of the bridge wires. Again, where the bridge wires have become rusted, there will be a variance in resistance. About the year 1922, one of the large coal companies was greatly alarmed by the number of serious and fatal accidents caused by misfires. The general manager issued an order that these accidents must be greatly reduced, and if possible, entirely prevented.

Jan 1, 1929

By Willis H. Carrier

PARTICULAR interest in the ventilation of deep mines, especially those in South Africa, has been created by a very complete system of cooling of the world's deepest mine, the Turf shaft of the Robinson Deep in Johannesburg. The writer visited this mine in January, 1936, and again in 1937. During these visits and subsequently, a considerable part of the theory involved in rock cooling in tunnels was developed and this has been checked by practical observations of the rates of rock cooling made within mines. The purpose of this paper is to set forth the method of attack of the mine problem. The cooling or air conditioning of mines by the use of mechanical refrigeration was not wholly new 1-5 when the Robinson Deep installation was made. The first mine to be cooled was the Morro Velho mine, in Brazil. The first installation in this mine was put into operation in December 1920, the refrigerant being ammonia.5 The surface cooling gave considerable benefit but it proved inadequate as greater depths were reached, therefore in 1929 two centrifugal refrigerating machines were installed at the 6000-ft. level. These were used in conjunction with the surface cooling system to furnish additional cooling at the lower levels. This later installation used Carrene as a refrigerant. This nonflammable refrigerant, having a boiling point of 104º at sea level, insured reasonable safety, since all parts of the machine operated at subatmospheric pressure. Very favorable reports have been received on the effectiveness of this installation, but no recent data are available. An interesting feature of that plant is that the condenser water is cooled by spraying it into the exhaust air from the mine at the base of the ventilation upcast, which permits the water to be cooled within a few degrees of the wet-bulb temperature of the air entering the upcast, and the only water that has to be supplied for condensing purposes is that lost by evaporation, or about 0.5 per cent of the volume circulating through the condenser. This plan affords an ideal means for the removal of the heat load from the refrigerating system, and of course also from the mine itself. In many mines, however, especially those in South Africa, there is no

Jan 1, 1938

By I. R. Kramer, P. D. Gorsuch, D. L. Newhouse

Although many methods have been suggested for the calculation of tensile strength and yield point from chemical composition, their usefulness has been limited to a particular cooling rate or section size. Further limitations have been imposed by failure to take into account many of the alloying elements that exert a considerable influence on the tensile strength or yield point. These systems, nevertheless, have filled an important need in many instances. The value of a system for the calculation of the tensile properties from the chemical composition and cooling rate is that it permits the prediction of the effect of alloying elements and heat-treatment on the mechanical properties, so that more efficient use of alloying elements may be made. Furthermore, it aids in the choice of steel for a given application aid tends to decrease the number of steels that otherwise would have to be tested. It is the purpose of this work to present a method of calculating tensile strength and yield point from the chemical composition and to suggest a method of correlating the tensile-strength and yield-point factors and cooling rate. Steelmakers have been interested for many years in the calculation of the tensile strength of hot-rolled steels. Quest and Washburn' summarize several of the attempts that have been made to devise formulas. They show the inadequacy of each of these formulas and present one of their own. It is apparent from their work that a simple additive equation of the type TS = A + BX + Cy + DZ + . . . , where A, B, C, D, etc. are experimentally determined constants and x, y, z, etc., are the percentages of alloying elements present in the steel, is not adequate to analyze fully the situation encountered in the calculation of tensile strength. For example, it was found that the difference between the calculated and observed values became progressively greater as the carbon and manganese contents were increased. Therefore, the effect of manganese was given as a function of the carbon content. Grossmann, in his work on the harden-ability of quenched steels, and Walter, in his method of calculation of tensile strength of normalized steels, present two cases in which multiplying factors were successfully used to express the combined effect of alloying elements. The factors in both cases were obtained from the fractional increase in hardenability or tensile strength with increase of alloy content. Yield point often is more important in design than tensile strength. For quenched and tempered steels a linear correlation exists between yield 2nd tensile strength.4 This is not true, however, for normalized

Jan 1, 1948

By P. D. Gorsuch, I. R. Kramer, D. L. Newhouse

Although many methods have been suggested for the calculation of tensile strength and yield point from chemical composition, their usefulness has been limited to a particular cooling rate or section size. Further limitations have been imposed by failure to take into account many of the alloying elements that exert a considerable influence on the tensile strength or yield point. These systems, nevertheless, have filled an important need in many instances. The value of a system for the calculation of the tensile properties from the chemical composition and cooling rate is that it permits the prediction of the effect of alloying elements and heat-treatment on the mechanical properties, so that more efficient use of alloying elements may be made. Furthermore, it aids in the choice of steel for a given application aid tends to decrease the number of steels that otherwise would have to be tested. It is the purpose of this work to present a method of calculating tensile strength and yield point from the chemical composition and to suggest a method of correlating the tensile-strength and yield-point factors and cooling rate. Steelmakers have been interested for many years in the calculation of the tensile strength of hot-rolled steels. Quest and Washburn' summarize several of the attempts that have been made to devise formulas. They show the inadequacy of each of these formulas and present one of their own. It is apparent from their work that a simple additive equation of the type TS = A + BX + Cy + DZ + . . . , where A, B, C, D, etc. are experimentally determined constants and x, y, z, etc., are the percentages of alloying elements present in the steel, is not adequate to analyze fully the situation encountered in the calculation of tensile strength. For example, it was found that the difference between the calculated and observed values became progressively greater as the carbon and manganese contents were increased. Therefore, the effect of manganese was given as a function of the carbon content. Grossmann, in his work on the harden-ability of quenched steels, and Walter, in his method of calculation of tensile strength of normalized steels, present two cases in which multiplying factors were successfully used to express the combined effect of alloying elements. The factors in both cases were obtained from the fractional increase in hardenability or tensile strength with increase of alloy content. Yield point often is more important in design than tensile strength. For quenched and tempered steels a linear correlation exists between yield 2nd tensile strength.4 This is not true, however, for normalized

Jan 1, 1948

By O. George Specht, Carl A. Zapffe

IN recent print, some remarkably contradictory statements have appeared regarding the importance to be attached to sponge iron,1-6 a metallurgical commodity whose history goes back at least to the time of Diodorus Siculus in the fourth century B.C. This disagreement, however, expresses the lack of a satisfactory method for producing sponge iron rather than defection in the commodity. The blast furnace is admitted to have certain inherent disadvantages, such as a general unsuitability for magnetite and the heating and blowing of vast quantities of undesirable nitrogen, so that a workable sponge-iron process remains attractive. In this respect, low-temperature gaseous reduction shows especial promise; but confusion persists regarding the factors involved. The present paper, therefore, has three principal divisions: (I) an exhaustive examination of all previous work on low-temperature gaseous reduction, (2) experimentation on the reduction of a magnetite with hydrogen, and (3) development of certain thermodynamic relationships in reduction, with a summarized depiction of the factors in the general process. PREVIOUS INVESTIGATIONS Gaseous media used in the reduction processes under discussion can be classified in three types: (I) H2, (2) CO, and (3) other gases. In the second, the CO is often admixed with H2. The third principally comprises hydrogeniferous gases, such as natural gas and producer gas, and in addition includes chlorine. Because hydrogen therefore features in all three, a study of hydrogen reduction based on investigations using pure hydrogen alone may be incomplete. The present paper reviews the three groups of investigations in the listed order, paying particular attention to hydrogen reduction. For the benefit of future workers, an exhaustive bibliography has been prepared and similarly classified. GROUP I: REDUCTION WITH HYDROGEN Equilibria Although the present problem is specifically one of kinetics, a first consideration is the equilibrium of the system, since the reactions to be studied comprise that equilibrium, and their direction and end points are defined by it. The historic development of these researches is interesting and informative.

Jan 1, 1946

By T. Lane Carter

BEFORE describing the experience with the Chinese on the Rand and the work they have accomplished, it will be necessary, sary, first, to give a brief account of labor-conditions in the Transvaal since the war, and then to show how the necessity of importation of labor arose. As is well known, the Transvaal mines are run on the dual system of labor-that is, the rough work is done by colored laborers under the superintendence of white men. From the start of mining operations in South Africa there has been the cry of shortness of native labor, due in great measure to the failure of Kaffirs to work continuously in the mines. While he works, the Kaffir is a satisfactory laborer, but his period of service is short, averaging about nine months. People unacquainted with the Kaffir have maintained that, by offering a higher wage and better accommodation, better results would be obtained from the native workers, but an increased wage simply aggravates the trouble. The Kaffir's wants are few. While at work he spends little of his money, and before long has sufficient capital with which to buy wives and become a gentleman of leisure. Doubling the wage of the Kaffir means that he acquires a competency in half the time, so that his period of service is correspondingly reduced. In 1899, before the war, there was always a cry about the scarcity of Kaffir labor. The highest number of natives at work was in July and August, 1899, when nearly 100,000 were employed. At the outbreak of hostilities the Kaffirs were scattered far and near, many doing well during the war by working for the military authorities. On the, resumption of mining operations on the Rand a serious mistake was made. Based on past experience, it was argued that if the whole industry decided to start anew with

Sep 1, 1908

By T. D. Yensen

In the investigation of the magnetic properties of iron-nickel alloys,' it was found necessary in order to make the alloys forgeable, or malleable, to add small quantities of some other element. Iron-nickel alloys have been known for nearly a century, but have been made in commercial quantities only since 1885. Their remarkable mechanical properties were disclosed by Riley in 1889 and from that time on a large amount, of research work has been done both to discover new properties and to correlate the results obtained.2 Lately the Bureau of Standards has collected the published data in a special circular" giving in compact form an account of the properties of the iron-nickel alloys. It also contains a clear historical sketch of the development as well as a selected bibliography. The chief difficulty with the development of iron-nickel alloys was that the "pure" alloys do not forge readily. The addition of small amounts of manganese, however, made the alloys forgeable, and manganese has therefore come to be regarded as a necessary constituent of nickel steels. The present paper shows to what extent manganese is needed for various nickel contents and also what is the effect of other alloying elements on the forgeability. It also touches upon the cause of forgeability but refers to other sources for more exhaustive treatises on the subject. The alloys were prepared by melting electrolytic iron and electrolytic nickel with or without other alloying elements in the desired proportions in a magnesia crucible in a vacuum furnace under a pressure of 1 mm. mercury. The ingots, weighing about 2 kg., were allowed to cool in vacuo. If pipes or blowholes were present, the ingots were cut in such

Jan 1, 1922

By T. D. Yensen

In the investigation of the magnetic properties of iron-nickel alloys,' it was found necessary in order to make the alloys forgeable, or malleable, to add small quantities of some other element. Iron-nickel alloys have been known for nearly a century, but have been made in commercial quantities only since 1885. Their remarkable mechanical properties were disclosed by Riley in 1889 and from that time on a large amount, of research work has been done both to discover new properties and to correlate the results obtained.2 Lately the Bureau of Standards has collected the published data in a special circular" giving in compact form an account of the properties of the iron-nickel alloys. It also contains a clear historical sketch of the development as well as a selected bibliography. The chief difficulty with the development of iron-nickel alloys was that the "pure" alloys do not forge readily. The addition of small amounts of manganese, however, made the alloys forgeable, and manganese has therefore come to be regarded as a necessary constituent of nickel steels. The present paper shows to what extent manganese is needed for various nickel contents and also what is the effect of other alloying elements on the forgeability. It also touches upon the cause of forgeability but refers to other sources for more exhaustive treatises on the subject. The alloys were prepared by melting electrolytic iron and electrolytic nickel with or without other alloying elements in the desired proportions in a magnesia crucible in a vacuum furnace under a pressure of 1 mm. mercury. The ingots, weighing about 2 kg., were allowed to cool in vacuo. If pipes or blowholes were present, the ingots were cut in such

Jan 1, 1922

By A. Steiner, K. L. Komarek

Activities of aluminum in solid Ni-A1 alloys have been determined between 20 and 60 at. pet Al and 1200" and 1400°K by an isopiestic method in which nickel specimens, heated in a temperature gradient, are equilibrated with aluminum vabor in a closed all-alumina system. The activity of aluminum shows a strong negative deviation from Raoult's law at low concentrations but increases by three orders of magnitude within the ß(NiAl) phase. The partial molar enthalpy and entropy of mixing are negative. Using Wagner and Schottky's theory of ordered compounds, a degree of disorder of 4 x 10 -4 for NiAl and 1.25 X 10-2 for FeAl has been calculated THE Ni-A1 system has been studied by a great number of investigators, and the results, as far as the phase diagram is concerned, have been compiled by Hansen.1 The phase boundaries from 0 to 50 at. pet Ni are well-established. At higher nickel contents the boundaries are still in dispute and an additional phase, A12Ni3, has been reported.' The phase diagram is dominated by a very stable high-melting compound, NiA1, with a relatively wide range of homogeneity. Heats of formation of solid alloys have been determined calorimetrically by Oelsen and Middel3 from 20 to 95 at. pet Ni and by Kubaschewski4 from 25 to 80 at. pet Ni. According to the most recent compilation5 no other thermodynamic investigations have been reported for the Ni-A1 system. Due to the corrosive nature and the low vapor pressure of aluminum, a method has been employed for determining activities of aluminum which was previously developed for the Fe-A1 system.= Nickel specimens, heated in a closed evacuated alumina system in a temperature gradient, were equilibrated with aluminum vapor from a source within the system kept at constant temperature. After complete equilibration the specimens were analyzed and activities calculated from the known vapor pressure of aluminum. APPARATUS AND EXPERIMENTAL PROCEDURE Materials. The nickel specimens were made from wafers of electrolytic nickel (International Nickel Corp.) of 99.99 pet purity which were rolled to a 0.001-in.-thick foil by Driver-Harris Co. and to a 0.005-in.-thick sheet in our laboratory. The aluminum (Aluminum Corp. of America) had a purity of 99.99+ pct. The alumina tubes and crucibles were made of impervious recrystallized alumina with an alumina content of 99.7 pet (Triangle RR, Mor-ganite Inc.). Experimental Procedure. Annular specimens were punched from the sheet, the punching burrs removed, and the specimens degreased in carbon tetrachloride and acetone and weighed on a micro-balance to within an accuracy of ±0.01 mg. The specimens were positioned with alumina spacers along an alumina tube, and the positions measured. Aluminum metal was machined into cylindrical shape, and placed into an alumina crucible. The tube with the specimens was then inserted into a hole drilled into the aluminum metal. An alumina tube with its closed end at the top was slipped over the specimens so that its lower end fitted snugly into the alumina crucible. The assembled reaction tube was inserted into a mullite tube with a water-cooled brass head which had an opening for a quartz thermocouple protection tube and a metal-to-glass connection to a conventional vacuum system. A Pt-Pt 10 pet Rh thermocouple could be raised and lowered in the quartz tube which was placed along the outside of the alumina reaction tube. The mullite tube was heated by two separately controlled resistance-tube furnaces so that in the experimental temperature range an over-all temperature gradient of approximately 150o to 250°C could be imposed on the reaction tube. The position of the mullite tube was adjusted so that the surface of the aluminum metal was always at the temperature minimum. The reaction tube was thoroughly evacuated before and during slowly heating the assembly up to the melting point of aluminum. A pressure of less than 2 µ (Hg) was maintained during an experiment. Once the aluminum had melted, it isolated the contents of the alumina tube from the surroundings. Several times during an experiment the temperature gradient was carefully measured. An experiment lasted from 3 to 6 weeks and it was terminated by air cooling the evacuated mullite tube. For further details of the experimental procedure the paper on the Fe-A1 system6 should be consulted.

Jan 1, 1964

By Alden Greninger

METALLURGISTS have long believed that martensite in steel forms as plates along the octahedral {111} planes of austenite. Much has been written about mechanisms whereby units of the austenite lattice are pictured as transforming to martensite by shearing movements initiated along the octahedral planes of austenite, supposedly resulting in plates of martensite lying parallel to these planes of shear. A critical inspection of two or three photomicrographs of quenched hypereutectoid steel led us to the conclusion that the orientation habit of martensite, at least in hypereutectoid austenite, could not possibly be octahedral. Inasmuch as recent studies30,31 of the martensite-type reaction in nonferrous alloy systems have established the irrational orientation habit as characteristic of this type of lattice transformation, the need for a thorough restudy of the crystallography of martensite formation in steel was evident. The present paper reports the results of such a study, extended to include both cementite and some of the products of constant-temperature decomposition of austenite. Also reported are a few of the results obtained from a microscopic and X-ray study of the austempering process in very high-carbon steel.

Jan 1, 1940

By David S. Cahn

Pilot-plant and laboratory tests were made on blends of steel plant flue dust and portland cement to determine whether the flue dust could be pelletized for use as a source of iron in dry process cement manufacture. Strength and setting time results showed that an acceptable agglomerate can be made with a Type II portland cement binder. Abrasion-resistant and well-sized pellets were made in a horizontal drum, using a simulated closed circuit, with a binder content of 7.5% and a moisture content below 15%. Pellet quality was found to be relatively insensitive to changes in binder concentration above 5%. Simulations of stockpiling and weathering indicate that little difficulty would be encountered with use of the flue dust pellets in cement plants.

Jan 1, 1972

By H. B. Pulsifer

.ABOut 1.5 varieties, or tnodifications, of the best rnagnesiurn available were prepared and subjected to etching tests, then examined for micro-structure. Of the 30-udd etching reagents that were tried, nearly half, mostly ammonium salts, etched the metal satisfactorily. The surfacing and etching of magnesium is shown to be a very simple and quick operation. The density and hardness of magnesium were determined. The most interesting new observations relate to the finding of the hexagonal etch figures, the crystal laminations, and the fact that the metal is plastic, cold, when restrained or quickly deformed. Under slowly applied pressule cold metal deforms slightly, then shears to fracture without plastic flow. The chief structural features of magnesium arc presented in two reduced photographs and 30 photomicrographs. Materials Tested There are only two sources in the United States from which new metal can be procured: the American Magnesium Corpn. and the Dow Chemical Co. No pronounced structural or property differences in the metals from these two companies were disclosed by the work of this investigation. The following materials were obtained from the manufacturers: 1. Massive crystals of distilled metal (American Magnesium Corpn.). 2. Rods of hot-extruded metal, ½-in. squares and 5/8-in. rounds (American Magnesium Corpn.). 3. Sheet magnesium, 0.005-in. thick (American Magnesium Corpn.). 4. Cast stick metal, 13/8-in. dia. (Dow Chemical Co.). 5. Magnesium-aluminum alloy, hot-rolled plate, ½-in. thick (American Magnesium Corpn.). From these materials, were prepared: 6. Sections from a furnace-cooled ingot made from clistilled crystal. 7. Cold-strained pieces from (6), (4) and (2). 8. Pieces cold-squeezed to fracture from (6), (4) and (2). 9. Hammer-struck pieces from (6), (4) and (2). 10. Steam-hammer struck pieces from (6), (4) and (2). 11. Sections from furnace-cooled ingot of the magnesium-aluminum alloy.

By Hjalmar Sjögren

Introduction.............767 Group I. The Ores of the Archean Crystalline Schists.... 770 Distribution............. 770 The Rocks.............770 Structures............772 The Rocks of Norrbotten..774 The Ores.............775 Type A. Apatite.Ores..........776 Type B. Mixed Hematite and Magnetite..777 Type C. Quartz-Banded Ores....777 Type D. The "Skarn" .Ores l..778 Type E. Limestone-Ores,..779 The Origin. of the Ore-Deposits......... 779 Arguments against the Sedimentation Theory,... 780 Concentration and Transformation within the Deep-Seated (Ana-morphic) Zone........783 The Chemical Changes.......784 Transformations in the Surface.Zone....789 The Graingesberg and Norrbotten Deposits,.....791 Analogous Deposits........794 Group II. The Ores of the Porphyries (Keratophyres) ... 796 Kiirunavaara. Luossavaara and TuoIlavaara....797 The Syenite.........799 The Porphyry of the, Foot. Wal1 .....799 The Porphyry of the Hanging-Wal1 ....799 The Ores.........800 The Forms and Dimensions of the Ore-Bodies ..802 Contact-Zones........803 The Genesis of the Deposits .......804 Mertainen and Painirova.......806 Ekatrömsberg..........808 Analogous Deposits,........808 Group 111. Magmatic Seregations in Basic Eruptives,... 809 Taberg in Smaland,.........811 Segregations in Diabase Younger than the Dala Sandstone, . 814 Iron-Ore in Nepheline. Syenite.......815 Ekersund and Soggendal in Norway......816

Jan 1, 1908

By G. L. Corrigan, J. R. Coleman

Four factors that largely determine the end product obtained when cement and water are mixed are the chemical compo ition of the cement, the fineness to which the cement is ground, the amount of mixing water used, and the procedure used in mixing the slurry. In order to study the effect of two of these factors, the other two, the chemical composition and method of mixing, are kept constant, leaving as variables fineness and water-cement ratio. Through years of experimentation and usage it has been well established that the reduction of cement clinker to a very fine state by grinding improves its cementing value, principally because the reaction between cement and water takes place only at the surface of the cement particle, further action being hindered by the accumulation of reaction products that tend to coat the unreacted material. Therefore, the more finely ground a cement, and the greater the surface exposed in proportion to its mass, the more rapid is the hydration rate. Similarly, the greater the surface exposed, the greater the proportion of the cement that reacts, and the lower the amount of residue that is unreacted and so remains inert and unable to make any contribution to cementing properties.1 Although it is more expensive to manufacture a finely ground cement than a coarser cement, the advantages of fine grinding of construction cements were so marked that the fineness of cement has increased considerably in past years. When the manufacture of special oil-well cements was begun, it was necessary to consider properties of cement that previously were considered of minor importance, foremost of these being pumpability. Since, with the water-cement ratio constant, a finely ground cement will produce a neat slurry of higher consistency and shorter time of pumpability than will a coarser cement, there is a tendency to grind oil-well cements to a lower degree of fineness. Therefore, in order to produce oil-well cements that will make a slurry having a long time of pumpability, cements are manufactured that because of their coarseness generally are poorer cementing materials than some of the more finely ground construction cements. On the other hand, often it is necessary to pump oil-well cements for long periods of time to place them properly behind a string of casing in a deep well, and since high strength is not of foremost importance for such cement, there is room for considerable controversy concerning the proper fineness range.

Jan 1, 1941

By B. W. Prof. Frazier

(Read at the Wilkes-Barre Meeting, May, 1877.) THIS interesting application of the laws of thermodynamics to metallurgical practice has not been discussed by any writer, within my reading, except the late Prof. Gallon of Paris. In his Cours de Machines,* Prof. Callon has given a short but lucid discussion of this subject in the admirably clear style for which he was remarkable. Although the interest attached to the subject is rather theoretical than practical, I have thought that an attempt to explain the mechanical action exerted in the hot-blast oven might not be entirely devoid of utility, especially in the suggestions which it involves. The statement, that the mechanical work performed in heating the blast is, when high temperatures are produced, considerably greater than the work performed by the blowing-engine, may seem incredible to many who are practically acquainted with the subject, appearing, as it does, to conflict with the results of their experience. It is, nevertheless, literally true, and I shall attempt in this paper to prove it, and to explain why it has not rendered itself palpably manifest in practice. Before proceeding to the mathematical demonstration, it will be well to recall to mind the definitions of some terms employed by writers in mechanics and thermodynamics. The actual energy of a moving body, as defined by Rankine, is the work which it is capable of performing against a retarding resistance before being brought to rest, and is equal to the energy which must be exerted on the body to bring it from a state of rest to its actual velocity. The value of that quantity is the product of the weight of the body into the height from which it must fall to acquire its actual velocity. * Vol. I, chap. x, [§ ] 4, p. 312.

Jan 1, 1878

By B. W. Frazier

This interesting application of the laws of thermodynamics to metallurgical practice has not been discussed by any writer, within my reading, except the late Prof. Callon of Paris. In his Cours de Machines," Prof. Callon has given a short but lucid discussion of this subject in the admirably clear style for which he was remarkable. Although the interest attached. to the subject is rather theoretical than practical, I have thought that an attempt to explain the mechanical action exerted in the hot-blast oven might not be entirely devoid of utility, especially in the suggestions which it involves. The statement, that the mechanical work performed in heating the blast is, when high temperatures are produced, considerably greater than the work performed by the blowing-engine, may seem incredible to many who are practically acquainted with the subject, appearing, as it does, to conflict with the results of their experience. It is, nevertheless, literally true, and I shall attempt in this paper to prove it, and to explain why it has not rendered itself palpably manifest in practice. Before proceeding to the mathematical demonstration, it will be well to recall to mind the definitions of some terms employed by writers in mechanics and thermodynamics. The actual energy of a moving body, as defined by Rankine, is the work which it is capable of performing against a retarding resistance before being brought to rest, and is equal to the energy which must be exerted on the body to bring it from a state of rest to its actual velocity. The value of that quantity is the product of the weight of the body into the height from which it must fall to acquire its actual velocity.

Jan 1, 1879

By Pei-Yung Huang, Carle R. Hayward

IN order to understand more fully the actual state of copper lost in copper reverberatory slags, a systematic study on the various reactions between certain metallurgically important copper compounds and synthetic copper reverberatory slags was undertaken by the authors in the Massachusetts Institute of Technology from 1942 to 1945.1 This paper, being only a part of the work completed, is published first because it furnishes the first experimental evidence of the formation of copper ferrite from reactions between cuprous oxide and copper reverberatory slags. CHOICE OF SLAG COMPOSITION The choice of the composition of the synthetic reverberatory slags to be used was much deliberated. Commercial copper reverberatory slags, neglecting minor constituents, average:2.3 45 to 47 pct FeO; 38 to 42 pct Si02; 5 to 6 pct CaO; 5 to 6 pct A1203. Since the ternary system CaO-FeO-SiO2 has been much more thoroughly studied4 and is much simpler than the quaternary system CaO-FeO-Si02-A1203, it was decided to use calcium oxide only instead of calcium oxide and alumina in the synthesis of the slags. Fortunately the composition of the average copper reverberatory slag with calcium oxide substituted for alumina lies in the region of the phase diagram clarified by the investigators. A survey of the phase diagram (Fig I) suggested two compositions: (I) the com¬position near the invariant point S, which is made up of 46 pct ferrous oxide, 37 pct silica and 17 pct calcium oxide; (2) the composition near the invariant point K with 45.5 pct ferrous oxide, 43 pct silica and 11.5 pct calcium oxide. Composition S has the advantage that the percentages of ferrous oxide and of silica almost exactly coincide with those of the average reverberatory slags, and that of the lowest melting point (1093° ± 3°C) in the whole ternary system. The calcium oxide content, however, obviously is high. Since we have already substituted calcium oxide for alumina, and since calcium oxide is more basic than alumina, the resulting slag is decidedly too basic. Composition K has a slightly higher melting point (1105° ± 3°C) and a higher silica content, but this is preferred because the slag is saturated with respect to tridymite and thus should not corrode siliceous refractories. Besides, it is less basic than composition S. The final slag composition, therefore, was chosen to

Jan 1, 1947

By Kenneth S. Ritchie

THE discovery well of the world's -deepest oil producing structure, University 1-B of Group No. One Oil Corporation, in the Big Lake oil field, Reagan County, Texas, has had a remarkable record. The well is outstanding for the following reasons: (1) It is the world's pioneer well to produce. oil in commercial quantities from a structure 8500 ft. below the earth's . surface; (2) this well was the only. producer from the 8500-ft. pay for a period of 17 months and 24 days; (3) the flow of the discovery well has been free from-the customary changes at the casinghead, with the exception of putting on a back-pressure of 185 lb.; and, (4) the well's daily production of oil and gas increased rather steadily for 17 months and 18 days from an initial of 40 bbl. per day to a maximum of 2926 bbl. per day, and then six months later, after a period of decline and self-readjustment to subsurface changes caused by six more deep producers, the well set its real record for one day's production of oil at 2950 bbl

Jan 1, 1931