Search Documents

By A. B., Sabin

THERE are many who know The Lucky Tiger and will remember the 35-mile road from Esqueda, a station on The Nacozari Railroad in northern Sonora, Mexico. They will remember the box canyons of the Agua Caliente Mountains which are scarcely wide enough for two cars to pass; the Bavispe River which one hour may be a lazy trickle and the next a sweeping torrent, and the tortuous road up Tigre and Espuela canyons, now following the wash, now hugging some gigantic red cliff. It is still the same. From camp the view of the distant blue-gray mountains is the same. But one thing a visitor of a former day might miss: The hundreds of pack mules and burros, loaded with concentrates from the mill, which used to take most of the road and show up at the most inopportune places, have almost disappeared, replaced of course by the auto truck.

Jan 1, 1929

A comprehensive, systematically structured mineral evaluation system is a prime requirement for objectively assessing mineral supply impacts on the economy. The Minerals Availability System developed by the US Bureau of Mines is a step in the right direction-a well-organized unraveling of the mineral supply network, structured in format to allow quick retrieval for rapid listing, supply analysis, and other uses.

Jan 9, 1977

By W. J. Moore, E. M. Swiggard, H. Shenker

Beryllium is the most soluble of the double-acceptor impurities in germanium; the solubility is at least 1 x 10 19 atoms cm3. Photoconductive, optical, and electrical measurements were made on a set of Ge:Be samples grown without other intentionally added imp~ivities. The excited-states spectrum of beryllium in germanium was determined both in zero field and in magnetic fields up to 30 kc. It was found that the absorption 0-f lines in the vicinity of the G line increased markedly with increasing magnetic field. The ioniza-tion energy of neutral beryllium in germanium was determined to be 24.3 * 0.1 mez: using the excited-states spectrum. An infrared detector using a Ge:Be element was found to have a normalized detectivity D* (50 p, 1000 cps, 1 cps) of 9 X ldO cm-~ps"~-w-'. The Ge:Be sambles exhibited low-field breakdown and inibzirity band conduction effects at low temperatures. WHILE the properties of most dopants in germanium have been thoroughly investigated, the properties of beryllium in germanium have had relatively little attention. Much of the work that has been done' has been concerned with the properties of singly ionized beryllium in germanium. The purpose of the present work was to determine the photoconductive and electrical properties of beryllium-doped germanium (Ge:~e) with a small concentration of other electrically active impurities. Ge:Be is of special interest since beryllium is the most soluble of the known double-acceptor impurities in germanium. MATERIALS PREPARATION A set of &:Be crystals with beryllium concentrations between 5 x 1013 and 1x 10'' cmm3 and without other intentionally added impurities was grown in a hydrogen atmosphere by the horizontal zone-refining techniques described by Swiggard and Shenker.2 The segregation coefficient of beryllium in germanium was found to be about 0.07 and its maximum solubility was found to be greater than 1 x 10'' atoms cm-3 which is in agreement with previous results.' Most of the crystals were found to have a small net concentration of shallow acceptors; for example, a crystal having a beryllium concentration of 1.1 X 1016 cm-3 was found to have a net concentration of shallow acceptors of less than 1.5 X 1013 cm-3. Ingots designed to have a beryllium concentration of 1 x 1017 cm-3 or less exhibited a loss of electrically active beryllium. That is, the beryllium concentration was lower than expected and the decrease of the beryllium concentration along the length of the ingot was much larger than expected. It is hypothesized that this effect is due to the oxidation of the beryllium by the residual oxygen in the system. This effect is similar to but not as severe as the effect observed with boron in germani~m.3, 4 OPTICAL ABSORPTION SPECTRUM The excited-states spectrum of neutral beryllium atoms in germanium was studied by measuring the infrared optical absorption spectrum. A typical spectrum is shown in Fig. 1; the labeling of the absorption lines follows that of Fisher and Fan.* The spacings between the observed lines and the D line are nearly equal to the corresponding spacings for the other ac -ceptors in germanium.5-7 By the use of the theoretical result67' that the neutral impurity ionization energy is 2.53 mev larger than the energy of the D line, the ionization energy of neutral beryllium in germanium was determined to be 24.3 * 0.1 mev at 4.2"K. This method yields a more precise value of the impurity ionization energy than the usual Hall effect method.' The absorption spectrum of Ge:Be was also measured as a function of magnetic field using a magnetic field parallel to the incident radiation and using unpolarized radiation. A typical spectrum taken at 30 kG is shown in Fig. 2. An unexpected observation is that the absorption of the lines in the vicinity of the G line (there is a strong possibility that some of these lines may be associated with lines other than the G line) increases with magnetic field. RESISTIVITY AND HALL DATA Measurements of Hall voltage vs temperature were made on several of the samples. The thermal activa-

Jan 1, 1968

By Theron Wasson

Michigan's production of 17,301,000 bbl. in 1945, which is in line with previous years, has been maintained by extensions to old fields like Deep River, Adams, Fork, and others. There were a number of new discoveries but, as in the past, these are not given very much importance because enough drilling has not been done to develop their potentialities; however, judging by the past, some of them will develop enough production so that 1946 -will probably be in line with other years. Activities in Michigan were confined to the Basin area of the lower Peninsula, which has been under development since 1925.

Jan 1, 1946

By Michael J. Callow

THE PROPERTY of Mount Isa Mines, Ltd., is located at Mount Isa, Northern Queensland, Australia, at roughly 20" south latitude. It is 600 miles from Townsville on the east coast, the port for Mount Isa, 1200 miles from Brisbane and approximately 1600 miles from Sydney in New South Wales. Living conditions in the camp, though wild and crude at the commencement of building, are now excellent and little has been left undone to provide comfort and attractiveness. The climate being warm and dry, many of the buildings are built on posts, 8 to 10 ft. off the ground, with spacious screened-in verandas. Club houses, stores, school, hospital and ice plant have all been provided by the company as well as modern conveniences, such as running water, shower baths, electric lights, septic tank arrangements, tennis courts and amusement grounds.

Jan 1, 1932

By John Howe Hall

One's first thought, upon being chosen to deliver the Henry Mario Howe lecture, is of pride at being selected for this post of honor, but ther succeeds immediately a deep sense of the Obligation thereby incurre to give of one's very best in order to make a contribution worthy of hir in whose memory these lectures are given. One who had the goo fortune to be associated with Henry ill. Howe, upon sitting down t prepare such a paper as this, irnrnediately falls to musing upon thc day when his face and his footfall were familiar from constant association, an recalls with singular vividness his active figure, his mobile, alert face, an his keenness in penetrating to thc corc of the subject under discussior Like Dr. Mathews, I was a young man when I first worked under hi direction, now nearly a quarter of a century ago, and in those early day he oft,en seemed a hard taskmaster—a man whose standards it woul never be possible for me to meet. I well recall his insisting upon m proving for the third time the truth of a conclusion which I had brc unwilling to submit to him until it had been confirmed by two carefull planned experiments. To my impatient protest that thc third .demor stration he asked for was but a repetition of the second, with differer samples, he replied, "Yes, that is true, but the inherent improbability ( your conclusions is so evident that I can not accept them until you prov your case again." "Shall I ever do a thing well enough to suit him? I thought. Looking back today upon many similar incidents, 1 suspect that h never expected me to attain the excellence he preached, and held up t me and to himself as a model, but knew out of the fullness of his experienc. that in no other way could he so impress upon me the necessity in researc of the patient, never-failing attention to detail and to accuracy tha distinguished his own work. How painstaking he was in the preparation of his many books an professional papers, as well as in his experimcntal work, was ncvcr s

Jan 1, 1929

By RUSSELL C. FLEMING

GILSONITE is a brilliant black, tarry-like bitumen, classed technically with glance pitch and graharnite as an asphaltite. As found it is brittle, breaking much like ice, and has a conchoidal fracture. Purest forms are used in the manufacture of paints, varnishes, electrical irisulatiorl, and inks for rotogravure; molded articles such as switch handles, telephone mouthpieces, and but- tons are made from the intermediate grades, and the poorer grades are used for the saturation of felt. According to the U. S. Bureau of Mines figures, production grew from about 4000 tons mined in 1904 to 55,000 tons in 1929. This asphaltic substance is found only in the Uintah basin in northeastern Utah, in veins over a wide area. Veins in the vicinity of Fort nuchesne were first discovered about 18G2, on what was then the Uintah Indian reservation, and the vein matter was originally called Uintaite because of that fact, In the early days, S. H. Gilson. of Salt Lake City, was so persistent and zealous in his efforts to develop the deposits and find a market that the name gilsonite was given to the material. Later, the wider and more renowned wins near Wayson and Dragon, in extreme eastern Utah, became the main supply.

Jan 1, 1932

By CHARLES W. BENTON

THE following paragraphs comprise such information as the Secretary has been able to obtain concerning the members and associates whose deaths have been reported. Further particulars or corrections of errors, and biographical data concerning deceased members or associates not already noticed in this way, are solicited. Charles IV. Benton was born at Kezar Falls, Maine, Nov. 12, 1843. We have no accurate knowledge concerning the early part of his career. In 1871 he engaged with the N. Y. Honduras Rosario Mining Co., at San Juancinto, Honduras, C. A., and later was employed at the Monserrat mine at Yuscaran, and at Santa Lucia, Honduras, with the Tenero Mining Milling Co. of Pennsylvania. In 1897 he became a member of the Institute. At the time he was stricken with his last sickness he was employed at the Paymaster mine at Tucson, Ariz. He died at Fairmount, Denver, Colo., Sept. 9, 1907. William R. Boggs, Jr.-The notice in the Bulletin for January was incorrect in saying that the murder of Mr. Boggs occurred while he was employed as metallurgical. manager by Mr. W. B. A. Dingwall, at La Maroma, San Luis Potosi, Mex. Mr. Dingwall writes that in March, 1907, Mr. Boggs left him, to return to his home at Winston, N. C., whence he. subsequently went to Durango, Mex., to take, with the Topia Mining Co., a position which he occupied at the tine of his death, Nov. 17, 1907. Mr. Dingwall says that, while in his service, Mr. Boggs never had any trouble with the workmen, but was esteemed and liked by them, as by all who knew him ; and adds, injustice to the State of San Luis Potosi, that the population, even in the mining-camps of that State, is orderly and law-abiding, and that the authorities are vigilant and just. Our

Mar 1, 1908

By S. A. Mersol, C. T. Lynch, F. W. Vahldiek

The microhardness of single crystals of tungsten disilicide has been investigated by the Knoop method. The average random room-temperature hardness of the WSi, matrix was 1350 kg per sq mm. Hardness crnisotropy was noted with respect to plane and indenter orientation as determined by single-crq.stal X-rny studies. Annealing at 1600" and 1800°C decreased the average hardness to 1310 and 1230 kg per sq tnm, respectively, and produced a second phase identified by X-ray diffraction and electron-microprobe analysis to be wSio.7. Ball-impact experiwzents produced rosettes at 850°C. Optical and electron microscopy showed evidence of slip and cross slip and twinning produced by microhardness indentations. Prismatic (100), [001] slip was found and cor~elated with hardness data. THE present study was undertaken to investigate the hardness anisotropy of as-grown and annealed single crystals of tungsten disilicide. The existence of the silicide WSiz in the W-Si system has been well-established and its structure thoroughly investigated zachariasen2 found WSi, to have a tetragonal C type of structure, similar to that of MoSi, with lattice parameters a = 3.212A, Kieffer et al. studied the W-Si system and measured the density and microhardness (at a 100-g load) of both polycrystalline WSi, and WSi,.,. The values found were 9.25 g per cu cm and 1090 kg per sq mm for WSi,, and 12.21 per cu cm and 770 kg per sq mm for WSi0.7, respectively. According to Samsonov et a1.5 the microhardness of polycrystalline WSi2 is 1430 kg per sq mm (at a 120-g load). EXPERIMENTAL The WSi, single-crystal boules investigated in this paper were grown by a Verneuil-type process using an electric arc by the Linde Division of the Union Carbide Corp.6 The largest specimens were 8 mm in diameter by 16 mm long. The crystals had an average density of 9.01 g per cu cm with a tungsten • silicon content of 99.9 wt pct. The major impurities were: 87 ppm O, 41 ppm N. 54 pprn C, 500 ppm Zr, 50 ppm Na, and 50 ppm Mn. The crystals were silicon-poor, the average silicon content being 22.20 pct (stoichiometric value is 23.40 pct), and tungsten-rich, the average tungsten content being 77.70 pct (stoichiometric value is 76.60 pct). As-received single crystals were ground and analyzed by powder X-ray diffraction technique using Cu Ka radiation. Laue and layer line rotation patterns were obtained on cleaved sections of WSi, single crystals. Electron-microprobe traverses of representative crystals were done using a Phillips-AMR electron microanalyzer. Carbon replicas were used to prepare electron micrographs. This work was done with a JEM-6A electron microscope. Prior to the metallographic examination, the specimens were mounted in Lucite and then polished for short times on polishing wheels using 9-, 3-, and 1-p diamond-grade pastes. Finally they were fine-polished with Linde A powder for 24 hr on a Syntron vibratory polisher. The samples were etched with 4H 2 O:1HF:2HNO3, which is a medium fast-acting etchant. The combination 1HF:2HNO3:5 lactic acid is also a satisfactory etchant. Annealing runs for selected specimens were made at 1600" and 1800°C for 3 hr at 1.0 to 3.0 x 10-5 mm Hg. A Brew tantalum resistance furnace with WSi2 powder for setters was used. The WSi2 powder was the same as that used for the crystal growth. Temperatures were measured with a calibrated W, W-26 pct Re thermocouple and a microoptical pyrometer. Powder X-ray diffraction, emission spectrographic, and electron-microprobe analyses were done after the annealing runs. For microhardness measurements a Tukon Microhardness Tester Type FB with a Knoop indenter was used. Although measurements were taken at loads ranging from 25 to 1000 g, the 100-g load was chosen as the standard load. All measurements were taken at room temperature. Only indentations of cracking classes 1 and 2 were considered.' DISCUSSION OF RESULTS Powder X-ray diffraction analysis showed the as-received crystals to be single-phase WSi2. Laue and layer line rotation patterns obtained on cleaved sections of WSi2 single crystals proved them to be tetragonal WS 2 2 The results also indicated that the c axis of the crystal was oriented parallel to the boule or growth axis. Electron-microprobe traverses across the matrix of the as-grown crystals showed them to be homogeneous WSi,. Optical and electron microscopy of etched crystals, however, revealed that they contained minute amounts of the "golden" and the "blue" second phases as opposed to the "white" or WSi2 phase. These two second phases were concentrated in inclusion and etch-pit

Jan 1, 1965

By Fredrick C. Kruger

Introduction This surprisingly little-known group of minerals, the nonmetallics, so-called for their lack of metallic luster, is the largest group of the mineral kingdom, and cinstitutes perhaps 75 percent of all mineral species. For the most part, these minerals are compounds of the common acids, oxides, hydroxides, and two elements, carbon and sulfur. The list of the non- metallic minerals, therefore, is very long. It includes the borates, carbonates, chlorides, fluorides, nitrates, phosphates, silicates, sulfates, and less commonly, arsenates, chromates, molybdates, suliides, tungstates, and vanadates, the latter groups, and many of the oxides, being sought principally for their metal content. Those nonmetallics used commercially are generally called the industrial minerals, although in addition this term also includes a considerable group of rocks. The list of industrial minerals and rocks is continually growing as new uses are found, and it now numbers over 300 commodities. The industrial minerals industry has developed since about 1920. There- fore, the development has been fast, and it has been more or less parallel with the development of the art of minerals beneficiation. General Discussion of the Group This group is so heterogeneous that it has defied logical, or widely accepted, classification, whether by origin, composition, or end use, and perhaps for this reason the industrial minerals generally have received short shrift in both teaching and research. Except for those involved with asbestos, cement, fertilizers, gypsum, salt, sand and gravel, few large companies have deigned to enter the field, and consequently most industrial minerals have been developed for the most part by the small operators or entrepreneurs. Yet surprisingly, except for one war year, the nonmetallics have always surpassed the metals in value and tonnage (Fig. 1). One main characteristic that most of the nonmetallics have in common is direct sensitivity to labor and transportation. In other words they are characterized by large bulk and low-unit value, and hence have what might be termed a "place value".

Jan 1, 1971

By Carl Zapffe

THE object of the Bradley process is to free manganese oxide from its associated gangue and separate the contained iron oxide by dissolving the manganese and precipitating it from the solution. 'The fundamental features of the process are : making. both 1 a manganese ore and an iron ore; effecting a separation of manganese .and. iron by means of selective roasting; leaching- the manganese from the roasted ore by using ' ammonium sulfate; precipitating the manganese by using the ammonia gas generated during leaching; fixing the precipitate by oxidizing with air; breaking down and reforming the ammonium sulfate, so that daily very little additional ammonium sulfate beyond that originally charged into the system is required; washing the manganese precipitate and the iron-silica residue and evaporating the liquor to conserve the dissolved salts in the moistures of these two products and 'to reduce the sulfur content,; drying the precipitates; magnetic wet-concentration of the iron-silica residue; sinteriny the manganese-and .the' iron-concentrates.

Jan 1, 1929

By F. G. Miller, E. B. Wilson

In 1972, coal mine productivity was in steady decline and labor and maintenance costs were spiralling upward. Yet, despite this sad state of affairs, nowhere in the US at that time was there a comprehensive and coordinated coal research and development plan in the offing. The Bureau of Mines had not yet been charged with such a responsibility, and industry was content to rely on machinery manufacturers for innovations. It was during this period that Bethlehem Steel Corp. determined that a new approach to coal mining research was needed for the industry as well as for the company itself. After studying Bethlehem's own mining practices, the state-of-the-art of mining research elsewhere, and development work by manufacturers, a comprehensive research package was presented to company management in late 1972. The ideas and experience of many operating and management personnel in the company contributed to the formulation of the final plan as approved.

Jan 10, 1976

By AIME AIME

THIS year the Chairman of the Institute's Iron and Steel Division is THIS William Anderson Haven, better known to the membership generally as Bill Haven. The Division Chairman is an individual endowed with a broad perspective of the ferrous metal industry he result of his earlier experiences as a successful operating man in the working and management of blast furnaces and his later experiences as an engineering-consulting executive concerned with the design and erection of and steel works throughout the world. William A. Haven was born to iron steel in the Pittsburgh district on ;. 1, 1888, and in due time--or in 1909 graduated from Penn State with a Bachelor degree in industrial chemistry.

Jan 1, 1944

By K. P. Gupta, A. K. Pal, L. Chandrasekaran, U. P. Singh

The Mn-Sn binary system, investigated at the high-manganese end and between 500° and 1000° C, shows four phases at temperatures below 727"C, namely the u Mn, the p Mn, the Mn3 Sn, and the Mn, Sn phases, while at higher temperatures only the last three phases remain stable. The solubility of tin in a Mn is very small and the maximum solubility of tin in P Mn phase appears to be abollt 10 at. pct Sn. The solubility range of the Mn,Sn and the Mn, Sn phases is 23.0 to 26.0 and 37.0 to 40.0 at. pct Sn, respectively. The lattice parameter of the 13 Mn phase increases with increasing tin content. The Mn, Sn thase is hexagonal with and appears to be basically of the Ni3 Sn type structure except that for quite a few X-ray diffraction lines the calculated and observed relative intensities do not agree well. The Mn-Sn binary system has been studied by several investigators.''~ Their results indicate that three intermediate phases, namely, the Mn3Sn, Mn,Sn, and MnSn, phases, exist at high concentrations of tin. However, so far the proper phase equilibrium has not been established at the manganese-rich end and very little data is available for the composition range between pure manganese and Mn3Sn. Moreover, earlier investigators differ in their opinion about the exact composition range at which the Mn3Sn and Mn,Sn phases appear and some doubt has been cast by some investigators3 regarding the structure of Mn3Sn phase which has been reported to be isotypic with Ni3Sn (Mgscd type) structure. In this investigation an attempt has been made to establish the proper phase equilibrium between pure manganese and Mn + 50 at. pct Sn composition in the temperature range of 500" to 1000°C. PROCEDURE The raw materials used were from three different sources. For exploratory work five alloys containing 5, 10, 15, 20, and 25 at. pct Sn were prepared using 99.9 pct pure manganese and tin supplied by E. Merck & Co., Germany. The rest of the alloys and one more 25 at. pct Sn alloy were prepared using 99.9 pct Mn supplied by Gallard Schlesinger Chemical Mfg. Corp., U.S.A., and 99.999 pct Sn supplied by Semi Elements Inc., U.S.A. Weighed amounts of manganese and tin were melted in recrystallized alumina crucibles in an inert gas (argon) high-frequency induction melting furnace. By careful control of temperature and time of melting the losses were reduced to below 0.2 pct in all cases. Since the losses were very small, no attempt was made here to analyze the samples chemically. Alloys were wrapped in molybdenum foil and sealed in small evacuated fused silica capsules. The alloys were annealed at different temperatures, controlled within + l°C, for sufficiently long periods to attain proper phase equilibrium, and subsequently quenched in cold tap water. The annealing periods used at different temperatures were 15 days at 500°C, 7 days at 600°C, 5 days at 700" and 750°C, 3 days at 800°, 850°, and 900°C, 2 days at 968"C, and two alloys annealed at 968°C were reannealed for 10 hr at 1000° C. From each annealed specimen, a part was utilized for metallographic study while another piece was used for X-ray diffraction study. 1.0 pct HNO, solution and oxalic acid solutions of concentrations 0.05 to 1.0 pct were used for etching Mn-Sn alloys above and below the MnsSn composition, respectively. Since all alloys were brittle, X-ray specimens were prepared using the as-crushed -325 mesh alloy powders. Only one 25 at. pct Sn alloy powder was reannealed in an evacuated silica capsule at 800°C for 5 min and water-quenched. X-ray diffraction patterns . for the Mn3Sn phase with the as-crushed and the reannealed powders did not show appreciable change. Un-filtered iron radiation at 25 kv, 15 ma was used with either Norelco 114.6-mm-diam Debye Scherrer Camera (for phase identification) or Norelco 12-cm-diam symmetrical focusing camera (for lattice parameter determination of the 6 Mn phase). The estimated accuracy of lattice parameter determination for the focusing camera was * 0.001A. RESULTS AND DISCUSSIONS The results of metallographic and X-ray diffraction study made with different alloys are shown in Fig. 1. The variations in lattice parameter with composition for the p Mn and the Mn3Sn phases are given in Tables I and 11, respectively, and the lattice parameter as a function of composition for the p Mn phase is shown in Fig. 2. The lattice parameter of the p Mn phase increases with increasing tin content while for the Mn,Sn phase the data obtained from two two-phase alloys and one single-phase alloy indicate increase in a,, and decrease in c, parameters with increasing tin content. The results, Fig. 1, indicate that the solubility of

Jan 1, 1969

By John S. Crandall

THE mineral garnet, while ordinarily considered a semiprecious gem stone or a second-grade industrial gem, has also proved itself in the field of industrial abrasives. Its use is well known as a sandpaper grain, and as a sandblasting sand its qualities are rapidly becoming recognized in more and more industries. Production of garnet as an abrasive is confined chiefly to two areas in the United States, North Creek, N. Y., where the Barton Mines Corp. operates, and Emerald Creek, Benewah County, Idaho, where Occurrence: Garnets in the Emerald Creek area occur as disseminated crystals in beds of micaceous schists of the Belt Series, which in this section are estimated to be close to 4000 ft thick. The schists are high in alumina and silica with iron, manganese, and magnesium. Subjection of the original sediments to high temperatures and pressures caused metamorphism to take place with the resultant re-crystallization of high alumina-silica minerals such as garnet, mainly spessartite and almandite varieties, cyanite, sillimanite, chlorite, actinolite, tourmaline, biotite, and muscovite, with minor amounts of ilmenite and magnetite. Quartz is also present in considerable amounts. Fast erosion of the soft mica schists on exposure to weathering has created extensive alluvial deposits containing up to 10 pct garnet having a maximum grain size of 3/16 in. These alluvial sands and gravels are now being treated for the recovery of garnet sands. Treatment: Overburden of 1 to 4 ft must be stripped to expose the garnetiferous gravels. This operation and the subsequent feeding of the gravels to a trommel-screen washing plant are performed by a % yd dragline. The trommel-screen openings are 3/16 in., thus allowing a separation and concentration based on grain size, since over 95 pct of total free garnets are minus 3/16 in. All plus 3/16-in. material is wasted at this point. The minus 3/16-in. material is further concentrated in a sand-drag classifier, where the slimes and silts are washed out and wasted. The sand product from the classifier varies in garnet content from 20 to 60 pct according to the particular section of ground being worked. This sand product is trucked to a jig plant where two sized fractions are made in a trommel-screen. The minus 3/16-in. plus 10-mesh portion is fed to a Pan-American two cell 42-in. jig. The minus 10-mesh portion is treated in a Bendelari three cell 42-in. jig. The jig concentrates are combined to form a 98 pct garnet sand. The jig tailings contain 3 to 5 pct garnet which is mainly flat crystals and chips which will not settle into the jig hutch. Subsequent treatment of these tailings in a scavenger jig followed by drying and electromagnetic separation will, according to tests, reduce the garnet losses in the tailings to something around 1 pct. Jig treatment of this feed approaches ideal as the major portion of the garnet crystals are the natural dodecahedrons and so are, in general, close to spherical. The specific gravity of pure garnet is 4.2, while the next heaviest mineral in the feed is cyanite with a specific gravity of 3.6, then quartz with specific gravity of 2.6. The garnet concentrate is practically free of quartz. The predominant impurity is cyanite which amounts to about 1.5 pct. The rod-like crystals of cyanite appear to up-end in the jig and go into the hutch with the garnets. Some ilmenite and magnetite appear in the concentrate but in very minor amounts. Subsequent washing in a sand-drag classifier removes fine silts and iron oxides. The gravel feed to the washing plant will average 8 pct recoverable garnet content. Concentration ratio in this plant runs about 2.5 to 1. Washing-plant concentrate as fed to the jigs will average 45 pct garnet by weight. Concentration ratio of jigging runs about 2.2 to 1. The garnet concentrate is dried in a rotary oil-fired drier and then fed to vibrating screens in closed circuit with crushing rolls. Practically any grit from 10-mesh down to 150-mesh grain size may be graded to specifications in two 3-deck vibrating screens. The present production, however, is approximately 75 pct No. 36, 15 pct No. 60. and the balance No. 80 and No. 100. Metal-screen cloth is used for sizes down to 36 mesh. From 36 mesh and finer, silk-screen cloth is used since it has less tendency to blind. All garnet sand is bagged in 100 lb self-sealing, sleeve-type paper bags. Practically all shipments are made in carload lots. Car loading is convenient since the plant is in Fernwood on the tracks of a branch line of the Milwaukee railroad. Truck shipments can and are made occasionally.

Jan 1, 1951

By John S. Crandall

THE mineral garnet, while ordinarily considered a semiprecious gem stone or a second-grade industrial gem, has also proved itself in the field of industrial abrasives. Its use is well known as a sandpaper grain, and as a sandblasting sand its qualities are rapidly becoming recognized in more and more industries. Production of garnet as an abrasive is confined chiefly to two areas in the United States, North Creek, N. Y., where the Barton Mines Corp. operates, and Emerald Creek, Benewah County, Idaho, where Occurrence: Garnets in the Emerald Creek area occur as disseminated crystals in beds of micaceous schists of the Belt Series, which in this section are estimated to be close to 4000 ft thick. The schists are high in alumina and silica with iron, manganese, and magnesium. Subjection of the original sediments to high temperatures and pressures caused metamorphism to take place with the resultant re-crystallization of high alumina-silica minerals such as garnet, mainly spessartite and almandite varieties, cyanite, sillimanite, chlorite, actinolite, tourmaline, biotite, and muscovite, with minor amounts of ilmenite and magnetite. Quartz is also present in considerable amounts. Fast erosion of the soft mica schists on exposure to weathering has created extensive alluvial deposits containing up to 10 pct garnet having a maximum grain size of 3/16 in. These alluvial sands and gravels are now being treated for the recovery of garnet sands. Treatment: Overburden of 1 to 4 ft must be stripped to expose the garnetiferous gravels. This operation and the subsequent feeding of the gravels to a trommel-screen washing plant are performed by a % yd dragline. The trommel-screen openings are 3/16 in., thus allowing a separation and concentration based on grain size, since over 95 pct of total free garnets are minus 3/16 in. All plus 3/16-in. material is wasted at this point. The minus 3/16-in. material is further concentrated in a sand-drag classifier, where the slimes and silts are washed out and wasted. The sand product from the classifier varies in garnet content from 20 to 60 pct according to the particular section of ground being worked. This sand product is trucked to a jig plant where two sized fractions are made in a trommel-screen. The minus 3/16-in. plus 10-mesh portion is fed to a Pan-American two cell 42-in. jig. The minus 10-mesh portion is treated in a Bendelari three cell 42-in. jig. The jig concentrates are combined to form a 98 pct garnet sand. The jig tailings contain 3 to 5 pct garnet which is mainly flat crystals and chips which will not settle into the jig hutch. Subsequent treatment of these tailings in a scavenger jig followed by drying and electromagnetic separation will, according to tests, reduce the garnet losses in the tailings to something around 1 pct. Jig treatment of this feed approaches ideal as the major portion of the garnet crystals are the natural dodecahedrons and so are, in general, close to spherical. The specific gravity of pure garnet is 4.2, while the next heaviest mineral in the feed is cyanite with a specific gravity of 3.6, then quartz with specific gravity of 2.6. The garnet concentrate is practically free of quartz. The predominant impurity is cyanite which amounts to about 1.5 pct. The rod-like crystals of cyanite appear to up-end in the jig and go into the hutch with the garnets. Some ilmenite and magnetite appear in the concentrate but in very minor amounts. Subsequent washing in a sand-drag classifier removes fine silts and iron oxides. The gravel feed to the washing plant will average 8 pct recoverable garnet content. Concentration ratio in this plant runs about 2.5 to 1. Washing-plant concentrate as fed to the jigs will average 45 pct garnet by weight. Concentration ratio of jigging runs about 2.2 to 1. The garnet concentrate is dried in a rotary oil-fired drier and then fed to vibrating screens in closed circuit with crushing rolls. Practically any grit from 10-mesh down to 150-mesh grain size may be graded to specifications in two 3-deck vibrating screens. The present production, however, is approximately 75 pct No. 36, 15 pct No. 60. and the balance No. 80 and No. 100. Metal-screen cloth is used for sizes down to 36 mesh. From 36 mesh and finer, silk-screen cloth is used since it has less tendency to blind. All garnet sand is bagged in 100 lb self-sealing, sleeve-type paper bags. Practically all shipments are made in carload lots. Car loading is convenient since the plant is in Fernwood on the tracks of a branch line of the Milwaukee railroad. Truck shipments can and are made occasionally.

Jan 1, 1951

By Thomas P. Forbath

THE sudden realization that known sulphur reserves amenable to mining by the Frasch hot water process are nearing exhaustion focused attention on widely scattered surface deposits throughout the world. These deposits are not necessarily of lower sulphur content than ores located underneath Louisiana or Texas salt domes which usually average about 30 pct sulphur disseminated in limestone matrix. Their near surface occurrence, however, renders exploitation by the Frasch process impossible. As is well known, the Frasch process depends on the presence of 500 to 1000 ft of overburden and cap rock above the sulphur deposits to permit melting underground sulphur in place by diffusing hot water under pressures of 200 to 600 psig in the formation and raising the molten sulphur to surface by air lift. This process renders possible the production of pure sulphur which is 99.5 pct pure without any subsequent treatment. Surface deposits contain sulphur in the same range of concentrations as the salt dome deposits, i.e., from 10 to 50 pct sulphur, associated with various gangue materials such as silica, limestone, and gypsum. The pirincipal distinction, then, does not lie in the percentage of sulphur contained in the ore, but in the geological nature of the deposit. A recent study' of the world sulphur supply situation estimated 1950 sulphur production in the free world countries at 5.6 million long tons, of which the United States produced 5.2 million tons, or 93 pct of the total. While America's domestic needs alone would have been covered by national production, about 1.4 million tons were exported during the same year. Despite all the steps which are being taken to restrict use of elemental sulphur and to force the fullest possible development of alternate sulphur sources here and abroad, the deficit in elemental sulphur production will probably increase with time. As a result of intensive prospecting for oil throughout the Gulf Coast area discovery of significant new salt domes is held unlikely. With the growing scarcity of sulphur and what appears to be an inevitable rise in price, recovery from deposits not amenable to Frasch-process mining assumes greater economic importance. Untapped Reserves The most important deposits in this category are located in Sicily, where elemental sulphur occurs in Miocene limestone and gypsum formation. Sulphur content of these ores ranges from 12 to 50 pct with an estimated average of 26 pct. Although quantitative estimate of these reserves is not available it is held that they exceed 50 million tons of sulphur. Similar deposits occur also on the mainland which contribute about one-third of Italy's total current annual production of 230,000 tons, but these are known to be nearing exhaustion. Significant surface deposits of volcanic origin are located in South America, Japan and western United States, silica being characteristic gangue con-stituent. The largest of these deposits are in South America. More than 100 extend over a zone 3000 miles long, paralleling the west coast of South America. 'Total sulphur content of these deposits has been estimated to be as high as 100 million tons. The main islands of Japan also possess at least 40 known volcanic sulphur deposits with probable reserves of 25 to 50 million tons.' Prospected reserves in western United States might amount to 2 million long tons, principal deposits being located in the northwestern part of Wyoming, southern Utah, and eastern California. Volcanic deposits of lesser importance are found around the Mediterranean, in Turkey and Greece, and in Africa, Egypt, Abyssinia, and Somaliland. Beneficiation Methods Different methods of beneficiation have been used in these various locations. In Italy the Calcarone kiln and Gill regenerative furnaces are used exclusively. Both utilize heat liberated by burning part of the sulphur in the ore to liquify or vaporize the remaining sulphur, which is recovered by solidification or condensation. The Calcarone kiln is of conical shape, generally 35 ft in diam at base and 18 ft high. A kiln of 25,000 cu ft capacity burns for about two months and yields about 200 tons of sulphur. The Gill furnace consists of a series of chambers with domed roofs. Sulphur is burned and melted in one chamber at a time and the hot combustion gases are used to preheat the ore charge in the subsequent cell. These furnaces operate on a cycle of 4 to 8 days. The recovery yield of both systems is about 65 pct. Sulphur losses amount to 25 pct through the combustion to sulphur dioxide; about 10 pct is retained in discarded calcines. Ores containing less than 20 pct are not considered suitable as furnace feed. These methods are not only wasteful because of the low recovery obtained, but represent a serious atmospheric pollution problem. Sulphur produced ranges from 96 to 99 pct purity and thus does not match Texas or Louisiana sulphur. Owing to the present shortage, sulphur in the Middle East sells

Jan 1, 1954

By G. M. Schwartz, D. M. Davidson

THE Duluth gabbro outcrops containing sulphides of copper, nickel, and iron are located on both sides of State Highway No. 1 an airline distance of 8.5 miles southeast of Ely in northeastern Minnesota. The region of known sulphide occurrences includes parts of sections 5, T. 61 N., R. 11 W., and parts of sections 25, 26, 32, 33, and 34, T. 62 N., R. 11 W. These sections, given in Fig. 1, are all in Lake County, Minnesota. Part of the area, which lies entirely within the Superior National Forest, is shown on the topographic map of the Ely quadrangle. The original discovery was made in 1948 when a small pit was opened in weathered gabbro rubble for use on a forest access road. A shear zone had caused unusual decomposition in this glaciated area, and the resulting copper stain was noted by Fred S. Childers, Sr., an Ely prospector, who began searching the outcrops along the base of the intrusive. He was joined in further exploration by Roger V. Whiteside of Duluth. In the summer of 1951 a small diamond drill was moved into the area and a hole 188 ft deep was drilled, passing through 11 ft of glacial drift into sulphide-bearing gabbro. This paper is a preliminary report on the geology of the newly discovered ore. The Duluth gabbro is one of the largest known basic intrusives and may be defined as a lopolith.' It extends northeastward from the city of Duluth as a great crescent-shaped mass that intersects the shore of Lake Superior again near Hovland, 130 miles to the northeast, see Fig. 2. The distance around the outside of the crescent is nearly 170 miles. The form of the intrusive is simple at Duluth where it ends abruptly north of the St. Louis River; at the east end, however, the gabbro splits into two elongated, sill-like masses separated mainly by lava flows and characterized by minor irregularities. The outcrop reaches a maximum width in the central part where it is about 30 miles across, and a maximum thickness of about 50,000 ft. It may be significant that the sulphides occur at the base of the thickest part. The lopolith has segregated into rock types ranging from peridotite to granite. The most abundant types are olivine gabbro, gabbro, troctolite, anortho-site, and granite. Of lesser importance quantitatively are peridotite, norite, pyroxenite, magnetite gabbro, and titaniferous magnetite. Grout estimates that two-thirds of the gabbro at Duluth is olivine gabbro. Variations in the percentages of plagio-clase, augite, olivine, and magnetite-ilmenite constitute the only essential differences found among the basic rock types. The predominant mineral is plagioclase, mainly labradorite. Plagioclase and olivine seem to have crystallized early, and the olivine rich rocks, usually troctolite, are found in the lower part. Segregations of titaniferous magnetite are abundant near the base of the gabbro along the eastern part and also occur far above the base. These have recently been described in detail by Grout.' Near the top, segregation has produced a gradation to granite, or "red rock," as it is known locally. This consists of quartz, red feldspar, and hornblende. The red rock forms a zone with a maximum width of nearly 5 miles but is quantitatively unimportant from Duluth northward for 35 miles. In Cook county, where the gabbro splits, each of the two sill-like masses has a red rock top somewhat thicker in proportion to the gabbro below than in the main central mass. The intrusive ranges from coarse to medium in grain size and from granitoid to diabasic in texture. Throughout much of the Duluth gabbro in Minnesota banding and foliation are well developed, as Grout has emphasized.V he bands are mainly a result of variation in the percentage of minerals, as in troctolite with alternating bands high in olivine and in plagioclase. A few bands may consist largely of one mineral, as is true of some segregations of magnetite. Many of the banded rocks show a clearly developed parallelism of platy plagioclase crystals, and both banding and foliation are believed to conform to the floor of the lopolith. Throughout its extent in Minnesota the Duluth gabbro dips east and south toward Lake Superior. It is generally believed to extend beneath Lake Superior and is found as a smaller mass exposed along the north side of the Gogebic district in Wisconsin and Michigan. The dip at and near the base ranges along most of its length from 20 to 40°, but at places the internal banding dips even more steeply. The dip of the upper part is much less, and if it is assumed that the flows along the north shore of Lake Superior are a dependable indication, it does not exceed 15". The formations shown in Table I which are intruded by the gabbro range from Keewatin to Middle Keweenawan in age. They present a significant picture. At the top, the gabbro and its accompanying

Jan 1, 1953

By G. M. Schwartz, D. M. Davidson

THE Duluth gabbro outcrops containing sulphides of copper, nickel, and iron are located on both sides of State Highway No. 1 an airline distance of 8.5 miles southeast of Ely in northeastern Minnesota. The region of known sulphide occurrences includes parts of sections 5, T. 61 N., R. 11 W., and parts of sections 25, 26, 32, 33, and 34, T. 62 N., R. 11 W. These sections, given in Fig. 1, are all in Lake County, Minnesota. Part of the area, which lies entirely within the Superior National Forest, is shown on the topographic map of the Ely quadrangle. The original discovery was made in 1948 when a small pit was opened in weathered gabbro rubble for use on a forest access road. A shear zone had caused unusual decomposition in this glaciated area, and the resulting copper stain was noted by Fred S. Childers, Sr., an Ely prospector, who began searching the outcrops along the base of the intrusive. He was joined in further exploration by Roger V. Whiteside of Duluth. In the summer of 1951 a small diamond drill was moved into the area and a hole 188 ft deep was drilled, passing through 11 ft of glacial drift into sulphide-bearing gabbro. This paper is a preliminary report on the geology of the newly discovered ore. The Duluth gabbro is one of the largest known basic intrusives and may be defined as a lopolith.' It extends northeastward from the city of Duluth as a great crescent-shaped mass that intersects the shore of Lake Superior again near Hovland, 130 miles to the northeast, see Fig. 2. The distance around the outside of the crescent is nearly 170 miles. The form of the intrusive is simple at Duluth where it ends abruptly north of the St. Louis River; at the east end, however, the gabbro splits into two elongated, sill-like masses separated mainly by lava flows and characterized by minor irregularities. The outcrop reaches a maximum width in the central part where it is about 30 miles across, and a maximum thickness of about 50,000 ft. It may be significant that the sulphides occur at the base of the thickest part. The lopolith has segregated into rock types ranging from peridotite to granite. The most abundant types are olivine gabbro, gabbro, troctolite, anortho-site, and granite. Of lesser importance quantitatively are peridotite, norite, pyroxenite, magnetite gabbro, and titaniferous magnetite. Grout estimates that two-thirds of the gabbro at Duluth is olivine gabbro. Variations in the percentages of plagio-clase, augite, olivine, and magnetite-ilmenite constitute the only essential differences found among the basic rock types. The predominant mineral is plagioclase, mainly labradorite. Plagioclase and olivine seem to have crystallized early, and the olivine rich rocks, usually troctolite, are found in the lower part. Segregations of titaniferous magnetite are abundant near the base of the gabbro along the eastern part and also occur far above the base. These have recently been described in detail by Grout.' Near the top, segregation has produced a gradation to granite, or "red rock," as it is known locally. This consists of quartz, red feldspar, and hornblende. The red rock forms a zone with a maximum width of nearly 5 miles but is quantitatively unimportant from Duluth northward for 35 miles. In Cook county, where the gabbro splits, each of the two sill-like masses has a red rock top somewhat thicker in proportion to the gabbro below than in the main central mass. The intrusive ranges from coarse to medium in grain size and from granitoid to diabasic in texture. Throughout much of the Duluth gabbro in Minnesota banding and foliation are well developed, as Grout has emphasized.V he bands are mainly a result of variation in the percentage of minerals, as in troctolite with alternating bands high in olivine and in plagioclase. A few bands may consist largely of one mineral, as is true of some segregations of magnetite. Many of the banded rocks show a clearly developed parallelism of platy plagioclase crystals, and both banding and foliation are believed to conform to the floor of the lopolith. Throughout its extent in Minnesota the Duluth gabbro dips east and south toward Lake Superior. It is generally believed to extend beneath Lake Superior and is found as a smaller mass exposed along the north side of the Gogebic district in Wisconsin and Michigan. The dip at and near the base ranges along most of its length from 20 to 40°, but at places the internal banding dips even more steeply. The dip of the upper part is much less, and if it is assumed that the flows along the north shore of Lake Superior are a dependable indication, it does not exceed 15". The formations shown in Table I which are intruded by the gabbro range from Keewatin to Middle Keweenawan in age. They present a significant picture. At the top, the gabbro and its accompanying

Jan 1, 1953

By N. S. Wagner, R. S. Mason

The production of lightweight aggregates in Oregon is a new industry, and, like all new enterprises, it is suffering from growing pains characterized by numerous, small operations some of which flourish for a short time and then cease altogether. Norinally all industrial mineral products are produced in a highly competitive atmosphere. At the present time this condition does not exist to a very marked degree in the state because as yet producers have not saturated the constantly expanding market. This paper has been prepared with the intention of outlining very briefly the current status of the various products now heing used as lightweight aggregates in Oregon. The present piche will surely change, perhaps quite radically within even a short space of time. Lightweight Aggregates Used in the Northwest PUMICE Interest in Oregon pumice is not new. Deposits are abundant. Successful development, however, dates only from 1946. During 1948 a total of nine operations was engaged in full or part-time production of aggregate. The postwar building boom and increased public consciousness regarding the value of insulation are the immediate reasons behind the current development. Just how firmly this production of pumice aggregate may be established is something which cannot be foretold at the present time. Much will depend upon how successfully the pumice aggregate construction already installed stands the test of time. Some fine pumice aggregate products have been made and it seems probable that because of its unique properties a certain demand for pumice aggregate will continue in the future. Fire-proof, rodent-proof, decay-resistant properties supplement the lightness in weight and insulation properties of pumice aggregate products in rendering them particularly ideal for many types of construction. In addition there has been fabrication in the form of reinforced fence posts, street markers, and similar products of a specialized-product nature and these are not to be overlooked in terms of future production. Also pertinent to how soundlj pumice aggregate production is established will be possible future competition with other lightweight aggregates. However, this situation will be governed largely by competitive costs of production and marketing. For its present use, which is almost exclusively limited to the manufacturing of building blocks, the market for Oregon pumice aggregate has been extended from the mining area around Rend and Chemult to points as far distant as San Francisco and Seattle. Naturally enough the bulk of the production goes to the Portland and eastern Oregon consumers. Shipments are made by both rail and truck. Early in 1947 the State Department of Geology and Mineral Industries made a canvass of all pumice producers in the state. The production for 1956 amounted to 26,614 cu yd and was valued at $13,649 at the plants. The United States Bureau of Mines estimates the production for 1947 as 33,240 short tons valued at $111,380. This is roughly 65,000 cu yd. No data are available for the 1948 production but it is understood to exceed that for 1947. The Oregon pumice occurrences originated largely from the eruption of Mount Mazama, the name of the formerly active volcano and the location of Crater Lake. Other lesser volcanoes throughout the area contributed to the present occurrences, however, and it has been estimated by Moore' that the pumice deposits cover an area of some 3500 square miles. This area lies east of Crater Lake between Bend and Klamath Falls and embraces the southern portion of Deschutes County, the northern part of Klamath County, and the northwest corner of Lake County. Thickness of the pumice ranges from thin skims to local thicknesses of as much as 30 to 40 ft. Fragment size also varies greatly. Any attempt to describe the situation by giving screen analyses would be confusing because of the wide variations to be found in all area of this size. The picture can best be summed up by stating that places showing great variations in fragment size can be found if a search for extremes is made. For mining purposes in connection with aggregate production, it call be stated that miles and miles of pumice exist in which the fragrnent sizes range from an inch or so downward. The usual color of the pumice is a light gray to off-white. A typical pumice analysis shows a silica content of about 69 pct, alumina 15 pct, and sodium oxide about 5 pct. Potash, lime, and water are the next three most abundant constituents, running just a little over 2 pct each. Iron oxides are fairly constant at 2.75 pct. Titanium, manganese, magnesium, and phosphorus occur in amounts of less than 1 pct. All of the foregoing substances are combined as a glass exhibiting cellular structure. The weight of crushed but otherwise pit-run (undried) pumice runs around 1100 Ib per cu yd according to figures furnished by various producers. The minimum and maximum weights per cubic yard reported are 1050 and 1400 lb, respectively. The 1400 lb per cu yd pumice contrasts with the pumice from most of the other

Jan 1, 1950