Search Documents

By R. C. Neavel

One of the most important requirements to be met by any coal producer is delivery of size consists tailored to specific applications. Generally these specifications include a minimum as well as a maximum size limit. The customers of a major Indiana coal producer noticed that some shipments of sized coal contained a large proportion of undersize pieces. Also, in these shipments, the pieces which remained within the specified limits were cracked and, when handled, crumbled readily. The producer, certain that these shipments had been properly sized at the tipple, suspected that degradation had occurred in transit. The Indiana Geological Survey was requested to examine the coal from one of these shipments to attempt to determine the cause of breakage. Two basic facts about coal and coal seams led to the employment of petrographic techniques in this investigation. First, all coal seams consist of accumulations of diverse organic and inorganic constituents; and second, most coal breakage, either desirable or undesirable, can be attributed to the inherent weakness of some of these constituents or to poor adhesion between certain constituents. Analyses of degraded coal Sampling: Samples were secured from 2 stock piles of 2-by 4-inch coal in a dealer's yard. The coal in both piles had received the same treatment from mining to storage, although it had been mined and shipped on two different days. The size consist of one pile, however, appeared smaller than that of the other. The sample from the degraded pile is referred to as the slack sample, and the other is called the unslack sample. Size analyses: In order to determine the actual size consist, the samples were screened, with a minimum of rough handling, on square 2-inch, 1-inch, 1/2-inch, and 12-mesh screens. It is assumed that 100 percent of the 2-by 4-inch coal is retained on a 2-inch round screen at the tipple. Analyses of several loads at the tipple indicate that approximately 26 percent of the 2- by 4-inch coal, 100 percent of which was assumed held on a 2-inch round screen, passed through a 2-inch square screen. Twenty-six percent may be taken as the normal difference between round and square screens. Results of the analyses of stockpile coal are shown in Table 1. Cumulative percent versus size are plotted on a Rosin-Rammler chart as Figure 1. Both samples approximately follow normal size distribution; this indicates that breakage is not size preferential and also that the samples are representative of the stockpiles. Although both samples exhibit the same general size distribution, the median size of the slack sample is considerably smaller than that of the unslack sample. Fifty-five percent of the unslack sample was undersize (29 percent greater than the normal 26 percent difference), and 83 percent of the slack sample was undersize (57 percent greater than the normal 26 percent difference). Both piles contained a greater percentage than normal of undersize coal; this indicates that they were both affected by degradation, but to a different degree. Bedding-plane analyses: Coal, because of its laminated nature, will break preferentially along bedding planes, especially where adjacent constituents are poorly cemented to each other. Subsequent breakage perpendicular to the

Jan 1, 1961

By A. W. Asman

The problem of balanced design in a belt conveyor has been under constant study. Increased use of this method of transport in recent years has stimulated investigations. Conveyor belt, power transmission and other machinery should be adequate to perform the required service. All components of the belt conveyor should work as an efficient unit moving its load continuously between terminals. As part of a long term research project on belt conveyors, Hewitt-Robins established in 1954 a 2-year grant at Pennsylvania State University. Under terms of the grant, certain fundamental phenomena were to be studied. This work evolved a new concept in belt conveyor power determination based on the principle of belt tension. The Penn State contract furnished the foundation for later more detailed studies. From these most recent investigations, more specific factors were defined. In the final analysis, all of the data collected has been worthwhile in belt conveyor design. Units now operate over long distances at speeds of over 800 fpm. Long high lifts are commonplace. Where vertical or inclined shafts were the rule, belt conveyors receive first consideration. Although belt conveyors have moved forward rapidly, the future will see a tremendous gain in their use. The ideal test belt conveyor would be several thousand feet in length and have a maximum tension of at least 70,000 lb., Also, this conveyor should be horizontai and have a variable feed rate of more than one material. Data from such a field belt conveyor combined with laboratory information would permit accurate analysis. Since this type of conveyor was not available, many field locations were visited: An alternate would have been to erect a closed circuit system in the laboratory. Either method had limitations and the first was selected as having the best possibilities. Manufacturers of conveyor belting and machinery basically have been using the same horsepower formula. As more information became available from field installations, factors in the basic formula were modified. Practically all conveyors are designed today by adding together the horsepowers required to move the empty belt, move the load horizontally, and elevate the load. In selecting size of drive motor, the first two elements are relatively unimportant if the last is large. However, it is the combination of

Jan 1, 1961

By R. W. Raymond

On the Manchuria. SOMEWHAT fatigued with excess of enjoyment and strenuous continuity of movement on the trip to and through California, the members and guests of the Institute party embarked Tuesday, Oct. 17, on the Pacific Mail S. S. Manchuria for a further journey to and through Japan. The good ship displayed the flag of the Institute (blue cross-hammers on a white ground), together with the Stars and Stripes and the ensign of the company. Uninterrupted fair weather and smooth water attended the passage to Honolulu. The Manchuria proved herself most commodious, comfortable and clean ("A sweeter steamship never sailed," quoth President Hunt) ; Captain Dixon and his officers were most agreeable, as well as most efficient; the passenger list comprised many congenial people besides ourselves-among them a score of missionary folk, and also Mr. M. H. de Young, Vice-President of the Panama

Jan 1, 1912

By D. G. Westlake

Levine has concluded that prismatic slip in titanium is controlled by two distinct thermally activated processes in the temperature ranges O° to 220°K and 220" to 300°K. We feel that his evidence is not convincing. He has drawn a curve through the plot of activation volume u* vs temperature T with a break at 22WK, Fig. 2. We believe that considering the possible experimental error apd the fact that there are only four points between 4° and 196°K, one could be justified to represent these points by the smooth curve we show as a solid line in Fig. 12. Levine believes that (8rf/aT)+ is discontinuous at 220°K, but he hints that he recognizes the possible doubt. We doubt seriously that the results shown in Fig. 1 indicate a discontinuity at 220°K. Certainly if he were justified in drawing a straight line through only four points on Fig. 2, we are even more justified in drawing straight lines through the seven points between 77" and 297°K on Figs. 1 and 3, because a straight line touches all seven of his circles. If his measurements of t were so precise that his decision to draw two curves in Fig. 3 is valid, then the experimental technique is deserving of further mention. We have drawn a smooth curve through the results in Fig. 3 and used this and the curve in Fig. 12 to obtain the values of shown in Fig. 13. Finding continuous is a contradiction of Fig. 4, which deserves comment itself. Levine obtained the solid circles in Fig. 4 using Fig. 2 and a smooth curve through the points shown in Fig. 3. We have replotted these solid circles in Fig. 14. We submit that there is no basis for his two straight lines (dashed in Fig. 14), and therefore have superimposed the curve that we believe is indicated. Certainly, there is reasonable doubt that a discontinuity in dH/dT exists at 220°K, even when one accepts Fig, 2. Furthermore, if one draws the straight lines indicated by least-squares treatments of the results presented as open circles in Fig. 4, their intersection is at about 196°K, not at 220°K as shown. Thus the alleged agreement between Figs. 3 and 4 with respect to "break" temperatures is not apparent. In Fig. 9, Levine has drawn a straight line very much different from the one indicated by a least-squares treatment. Obviously, he has done this because he recognized that H = 0 when T = 0. He is consistent in drawing the low-temperature curves in

Jan 1, 1968

By W. L. Connell, O&apos

The properties of some heavy liquids which can be used in sink-float separations are discussed with major emphasis being given to the halogenated hydrocarbons. Data are presented on density, viscosity, thermal characteristics and the effects of moisture and temperature on the corrosiveness of the liquids towards various materials of construction. The toxicity of these materials, the hazards involved in handling them, and the procedures for handling them safely are also discussed. True liquids have certain advantages over colloidal suspensions for sink-float separation of minerals which makes their use especially advantageous when close separations, fine particle sizes or water-soluble minerals are to be treated. For best separating results, the medium should have an easily controlled, uniform, stable density. Here, true liquids have the advantages of allowing closer control of density and of not requiring agitation to maintain a uniform den- sity in the equipment. Low viscosities are desired in a separating liquid so that rapid separations of fine material can be made. Many liquids have lower viscosities than the colloidal suspensions at operating gravities of 1.4 to 5.0. For economic reasons and to prevent contamination of the product, the separating medium must be easily and completely removed from the ore. Normally, true liquids must be more completely removed than the cheaper suspensions and thus cause more problems in this area. The fact that the medium should not react with the minerals, air, water or the common materials of construction limits the choice of liquids which can be used, but many are available which are sufficiently stable. A more serious objection to the use of true liquids is that many of them present a toxic hazard to operating personnel and users of the product. Most true liquids are toxic to some extent, but modem knowledge of toxicity allows us to recognize the hazards inherent in handling them and enables us to design around them. Three types of true liquids are available for this use: 1) Halogenated hydrocarbons cover the gravity range from 1.2 to 3.3. They are generally more volatile and less viscous than the other liquids.

Jan 1, 1963

A record $18.7 billion worth of metals, non- metals and fuels was produced in the U.S. during 1962, according to a year-end estimate from the USBM. The 1962 total value, based on preliminary statistics compiled by the Bureau, was nearly $600 million more than in 1961. Most minerals gained both in value and volume of production during 1962 according to information collected by the Bureau. All mineral fuels except anthracite showed increases. Among nonmetallic minerals- other than fuels-gains exceeded losses by two to one. Metal production held steady as gains and losses balanced.

Jan 2, 1963

By Henry M. Howe

(Cleveland Meeting, October, 1912.) Manuscript received Aug. 20, 1912. PROFESSOR RUFF'S most illuminating paper' describing his extremely valuable investigation of the carbon-iron equilibrium diagram assigns definite temperatures to certain very important lines in the diagram, viz.: the eutectic temperature EB (Fig. 1) and the " near-eutectic " temperature E'B', but without indicating clearly enough the reasoning which warrants these assignments. These temperatures are of such primary importance that it is well to indicate the apparent gaps in the reasoning, in the hope that they may be filled in. In his diagram, Fig. 1, the point X and the lines B'D'HI represent the experimental results reached by Ruff and Goecke; 2 AB, AEB, and SE represent the liquidus, the solidus, and the solubility of the carbon in solid austenite in the absence of graphite according to Gutowsky,3 AB being also in accordance with Spiecker's data;4 ,S'E' the solubility of carbon in solid austenite in the presence of graphite according to Ruer and Iljin; 5 GS the line A3 after Goerens and Meyer;6 I and EBC the true eutectic line as inferred by Prof. Ruff from Gutowsky's data. B'D' is the carbon content found in cast-iron which had apparently saturated itself with carbon in the presence of the graphite of the enclosing graphite crucibles in which the determinations were made. From its straightness and its sharp inflection near 6.67 per cent. of carbon, the carbon content of * Professor of Metallurgy in Columbia University. 1 Metallurgie, vol. viii., pp. 456 to 464 and 497 to 508 (1911). 2 Idem, vol. viii., pp. 417 to 421 (1911). 3 Idem, vol. vi., pp. 731 to 743 (1909). 4 Idem, vol. vi., p. 524 (Wüst) (1909). 5 Idem, vol. viii., pp. 97 to 101 (1911). 6 Idem, vol. vii., pp. 307 to 312 (1910).

Nov 1, 1912

By W. C. Lacy

This article is a progress report of a program designed to quantitatively evaluate geological parameters to predict stable slope angles. The author feels that, although there does not appear to be any one technique or characteristics that will suffice as an index to the determination of stable slope angles, a combination of seismic methods as outlined here, detailed geological mapping and logging of core, and a better understanding of the angle of internal friction in rock types will permit accurate estimation. A mining engineer friend once remarked, "If we don't have pit slope failures, the slopes are too flat." Since economic justification of an open pit project is based upon ultimate pit slopes, we cannot wait until the pit is developed and slopes established by trial and error. Some combination of geological and/or geophysical techniques must be developed to permit accurate prediction of stable slope angles and to suggest modification of pit outlines to result in slopes enabling maximum economic yield. This presentation is a progress report of a program designed to quantitatively evaluate geological parameters to predict stable slope angles. The principle of the weakest link applies to any slope stability evaluation and necessitates detailed geological examination and recording of observations. Physical failure will occur along any surface where shearing stress exceeds shearing resistance. Rock conditions are seldom uniform even within a single cut or pit face, so stability conditions will vary. Consequently, both plan outline and ultimate slope limits must be tailored to the specific situation. Economic advantages to be gained by slight increases in slope angles in deep pits are well recognized and stimulate efforts to obtain maximum permissible slope angles. MECHANICS OF SLOPE FAILURE Excellent reviews on the nature of slope failure have been presented+2,6,8,11 For the purpose of this study, the writer considers failure to take place by one or more of three processes: 1) ravelling, 2) translation or slope failure, and 3) rotation or base failure (Fig. 1). The effects of increased pore water pressure in soils were recognized in 1923 by Terzaghi in his development of the concept of effective stress, and he has applied the same principle to jointed rocks designating water pressure as cleft-water pressure.8 Cleft-water pressure in a rock slope reduces normal pressure on the plane of failure, thus reducing shearing resistance and resulting in slope failure. In the following discussion it is assumed that adequate drainage is supplied to prevent any build-up of water pressure. This is the first step in any program to establish maximum slopes. Ravelling: Ravelling occurs in rocks with low cohesion and entails the free movement of individual fragments ranging from single rock falls to running ground. Removal of lateral support wherever slope angle exceeds the angle of repose of the rock parti-

Jan 1, 1963

By J. L. Gregg, J. L.

RECENTLY there has been considerable interest in the production and use of extra hard alloys composed primarily of tungsten and carbon. Dr. Hoyt's recent paper1 gives a good description of these alloys and describes their performance when used as tools. There are a number of these alloys on the market sold under various trade names, and it is the purpose of this paper to describe the results of an investigation of the structure of five of these alloys by means of microscopic and X-ray methods. The samples studied were in the form of small tools or wire-drawing dies, which were either purchased or supplied as samples. They were in some cases not supplied by the original makers but were furnished by the agents in this country, and we wish to call attention to the fact that they may not be truly representative of the materials supplied under the various trade names. No performance data are given and no inference as to the inferiority of one alloy as against any other is made. K. Schröter2 recently described methods for polishing alloys of this type for microscopic examination and has presented photomicrographs of several alloys. However, he did not identify their constituents or describe methods for their identification.

Jan 1, 1929

By H. T. Kennedy, S. G. Dardaganian, J. L. Clanton

This paper presents equilibrium ratios measured on oil and gas samples taken from the Kelly-Snyder field at the reservoir temperature of 128°F. From these data smoothed curves were constructed for the reservoir fluid up to the bubble-point, 1,874 psia. A material balance calculation, based on the use of equilibrium ratios instead of the usual solubility and shrinkage meayr~rements is made on the field and compared to the con\.entional method. DETERMINATION OF EQUILIBRIUM RATIOS The equilibrium ratios, or K values were obtained by recombining separator samples of oil and gas taken when the reservoir was above its bubble point, and thus represented the reservoir fluid before any change had occurred due to the evolution of gas. The well sampled had a gas-oil ratio of 617 cu ft of high pressure sepalator gas per barrel of separator oil. and a bottom-hole temperature of 128°F. Samples were brought to equilibrium by agitating for 24 hours in a thermostat, maintained at the proper temperature within 0.2ºF, mercury being added when necessary to maintain the pressure constant. Samples of oil and gas were then taken by constant pressure displacement, and analyzed by low temperature frac-tionation. Equilibrium ratios were determined at 128°F and 500, 800, 1,000 and 1,400 psig. At the latter pressure, there were indications that the gas samples were contaminated with small quantities of oil, and only data taken at the first three pressures were included in Fig. I. This figure has been extended to higher and lower pressures by the use of the Fluor charts for 3,000 psi convergence pressure, on which the experimental points fit well. MATERIAL BALANCE EQUATIONS The possible errors involved in conventional material balance equations have been analyzed by Muskat1. Where the errors occur in field measurements, or in obtaining effective averages from variables such as gas-oil ratio and pressure, they will evidently be involved in any attempt to estimate the content of the reservoir. On the other hand, substantial errors may be introduced in conventional material balance calculations by: (1) the neglect of the amount of oil dissolved in gas at high pressures and temperatures in the reservoir, but which condenses under separator conditions; (2) the assumption that the separation of oil and gas in the reservoir may be duplicated by a differential liberation in the

By C. H. Wayman, D. W. Fuerstenau

The effect of bubble size and concentration of certain reagents on the terminal velocity, shape, path, and drag coefficients of single air bubbles in distilled water has been investigated. Bubbles of a certain size range rise considerably faster than Reynolds number-drag coefficient relationships predict, whereas a small amount of frothing agent reduces their terminal velocity. The rapid velocity at which bubbles rise in distilled water appears to result from slip at the boundary and from circulation within the bubbles. Surface-active agents retard bubble motion through prevention of both circulation and slip at the boundary. A surface tension concentration gradient helps maintain bubble sphericity. HE gas phase is one of the indispensible in-gredients in flotation operations. Flotation depends on the collision of an air bubble and a mineral particle in a pulp and their ability to remain in contact long enough for adherence to take place. Before it is possible to understand the mechanics of air bubble-mineral particle encounter, it is necessary to learn more about the nature of bubbles themselves before collision with a mineral particle has taken place. To date, little work has been done on air bubbles in flotation systems. In 1945 Fahren-wald' presented a study of the role of frothers on air bubbles and on aeration in flotation, and recently Wark and Sutherland' discussed the work of Rosenberg- in relation to flotation. The research reported in this present article was undertaken to investigate systematically the effect of bubble size and the concentration of certain reagents on the terminal velocity, shape, path, and drag coefficient of single bubbles in distilled water. Most of the work is concerned with the effect of a-terpineol on bubble motion in water, but studies were made with potassium chloride, potassium hydroxide, potassium ethyl xanthate, and potassium amyl xanthate. Experimental Method and Materials: To obtain free bubble rise and reduce wall and surface effects, the investigators used a tank of 5½x5½x30-in. internal dimensions, filled with water to within 4 % in. of the top.' The tank was made of acrylic plastic so that the walls would have good optical properties. Distilled water, which was re-distilled in a block tin still and saturated with air before each test, was used in all the experiments. All solutions were made with reagent-grade chemicals. During each experiment the water was at room temperature, and during the course of an experiment the temperature did not fluctuate more than 0.5°C. Since the experiments were performed over a period of six months, the temperature varied between 25° and 27°C. The temperature at which each series of experiments was conducted is recorded with the data. The experimental apparatus is presented dia-grammatically in Fig. l. Individual air bubbles were generated from purified compressed air through a capillary of 0.003-cm internal diameter at a rate

Jan 1, 1959

By J. E. House, J. L. Drobnick, R. R. Swanson, D. W. Agers

The paper describes an improved process for the recovery, purification, and concentration of copper values from acidic dump leach liquors. The process employs a new liquid ion exchange material (LIX® 64 reagent) capable of separating copper values from iron and other impurities common to dump leach liquors in the typical pH range of 1.4-3.0. Properties and performance of the reagent are discussed. Design scale-up information for both pilot plants and commercial installations, including preliminary economics, are presented. Economic considerations include the production of electrolytic copper from the purified copper aqueous concentrate. INTRODUCTION Since the commercial acceptance of the liquid ion exchange process in the mineral processing industry, it has been predicted that a wide selection of chemical reagents to efficiently and economically separate many metals in solution under a wide range of conditions would be commercially available. Several years ago, General Mills began a basic research and development program to determine if it were possible to develop a reagent to extract economically metallic ion from existing process streams. Progress toward reaching this objective was reported in late 1963, when development of quantities of LIX -63 reagent, a highly selective reagent for the extraction of copper, was introduced. The properties of this reagent are described in a previous paper.' The development work with this reagent indicated that perhaps the largest potential application for a copper extractant, the treatment of acidic dump leach liquors, would not be economically possible with LIX-63 because of limitations of the reagent to extract copper below a pH of 3.0. The relatively small pH adjustment required with LIX-63 would result in a significant processing cost and the undesirable precipitation of ferric hydroxide from the liquor. This pointed to the need for another copper extractant which would extract copper from dump leach liquors without pH adjustment. General Mills was successful in synthesizing a molecule which does not have the pH limitation of the LIX-63, yet possesses the selectivity-solubility properties required of a metallic extractant. The resulting LIX-64 reagent broadens the pH range from which copper can be effectively extracted and separated from other metallic impurities. Of special significance is the fact that the reagent, LIX-64 was developed by combining the technical requirements of a specific problem in hydro-metallurgy with theoretical organic and physical chemical principles.

Jan 1, 1967

By Gorr W. W., Wyche E. H, R. Smith

The combination of high strength and corrosion resistance of cold-worked 18 Cr, 8 Ni steel has been advantageously utilized for some time, particularly in aircraft and rail car structures. There are, however, certain limitations on the use of such materials because the high strengths can be obtained only by cold-working, limiting the available products to sheets, strip, wire and tubes. The authors sought to overcome these limitations by resorting to precipitation-hardening, which has been used so successfully in nonferrous metallurgy but only to a limited extent in iron-base alloys. Accomplishment of this objective not only overcame the limitations, but also effected certain improvements in mechanical and other properties. This paper is an account of the development by Carnegie-Illinois Steel Corporation of a precipitation-hardening 18-8 stainless steel (called Stainless W‡ and tentatively identified as type 322). A description is given of its composition and metallurgical characteristics, heat-treatment, physical and mechanical properties and corrosion resistance. Development of the New Steel For a considerable length of time the authors were unable to determine the mechanism of the precipitation-hardening process that had been noted by Ffield18,19 in 18-8 Ti or 18-8 Cb after cold-working and reheating to moderately elevated temperatures. All known variables were exhaustively studied, but with little success. However, results began to indicate that chemical composition was the most important variable, particularly the ratio of austenite-forming to ferrite-forming elements. The investigators then focused their attention upon the composition, and, in particular, upon the element titanium and its mode of alloying in the presence of other elements. A heat was obtained that could not be brought to the softness level of annealed 18-8. The response to cold-straining and aging* was very marked by previous standards, and, more important, cold-straining was found to be entirely unnecessary to produce the precipitation-hardening effect. The chemical composition of this heat was: C, 0.06 per cent; Mn, 0.54; P, 0.016; S, 0.016; Si, 0.58; Ni, 7.28; Cr, 17.60; Ti, 0.90; Al, 0.17. For some time the development work, particularly on composition, was carried

Jan 1, 1947

By Gorr W. W., R. Smith, Wyche E. H

The combination of high strength and corrosion resistance of cold-worked 18 Cr, 8 Ni steel has been advantageously utilized for some time, particularly in aircraft and rail car structures. There are, however, certain limitations on the use of such materials because the high strengths can be obtained only by cold-working, limiting the available products to sheets, strip, wire and tubes. The authors sought to overcome these limitations by resorting to precipitation-hardening, which has been used so successfully in nonferrous metallurgy but only to a limited extent in iron-base alloys. Accomplishment of this objective not only overcame the limitations, but also effected certain improvements in mechanical and other properties. This paper is an account of the development by Carnegie-Illinois Steel Corporation of a precipitation-hardening 18-8 stainless steel (called Stainless W‡ and tentatively identified as type 322). A description is given of its composition and metallurgical characteristics, heat-treatment, physical and mechanical properties and corrosion resistance. Development of the New Steel For a considerable length of time the authors were unable to determine the mechanism of the precipitation-hardening process that had been noted by Ffield18,19 in 18-8 Ti or 18-8 Cb after cold-working and reheating to moderately elevated temperatures. All known variables were exhaustively studied, but with little success. However, results began to indicate that chemical composition was the most important variable, particularly the ratio of austenite-forming to ferrite-forming elements. The investigators then focused their attention upon the composition, and, in particular, upon the element titanium and its mode of alloying in the presence of other elements. A heat was obtained that could not be brought to the softness level of annealed 18-8. The response to cold-straining and aging* was very marked by previous standards, and, more important, cold-straining was found to be entirely unnecessary to produce the precipitation-hardening effect. The chemical composition of this heat was: C, 0.06 per cent; Mn, 0.54; P, 0.016; S, 0.016; Si, 0.58; Ni, 7.28; Cr, 17.60; Ti, 0.90; Al, 0.17. For some time the development work, particularly on composition, was carried

Jan 1, 1947

By Lewis Blanchard Brown

It is my purpose in the following paper to describe the south-central part of Siberia, with special reference to its geology and the mineral deposits. This region is known politically as the Achinsk and Marinsk districts of the Tomsk Government. It is situated among the Altai mountains, in. ]at. 50° to 55O n and long. 87O to 93O E., not far from the northern frontier of Mongolia, and is divided as follows: Mining Districts.—(1) The Tomsk mining district, including the political districts of Altai (belonging to the private crown lands of the Russian Emperor) and Marinsk; (2) the AchinskMinusinsk mining district, including the political districts of Achinsk and Minusinsk; and (3) the North Yenisei mining district, situated in the northern part of the Yenisei political district of the Yenisei Government. Fig. 1 is a map of the Tomsk mining provinces, showing the useful mineral-deposits, excepting those of gold, and giving the routes of the railroads and post-roads connecting the various districts. Political Divisions.—The Tomsk Government is sub-divided into seven " oojesdy " or districts, as follows: Barnaul; Biisk; Kuznetsk; Kainsk; Kolyvan; Marinsk; Narim; and the Altai district (private land, as above). The Yenisei Government is sub-divided into five "oojesdy" or districts, as follows : Erasnojarsk ; Kansk; Yenisei; Achinsk; Minusinsk. Concerning the geology of the region, in addition to the record of my own observations, references will be made to the works of earlier writers. These have been consulted for the purpose of comparison, as regards the districts which I have actually traversed, and for the purpose of completing my account of such portions as I have not been able to visit.

Jan 1, 1904

By E. Northcott, F. N. Oberg

By electrostatic separation, course Florida pebble phosphate, too lou-grade to find a ready market, can be upgraded to a satisfactory saleable product. Pebble running from 60 pct bone phosphate of time may be upgraded to 73 to 77 pct BPL depending on the mineralogical. structure of the pebble and the nature of the silica innpurity. High-grade concentrates from Florida pebble phosphate deposits have long been recovered by wet methods. When work was begun in the field, only the coarse pebble (generally +1 mm) was re- covered. In the 1920's a froth flotation process was developed to separate quartz from the finer phosphate fractions, but this method proved unsatisfactory for treating the intermediate fraction (—1 mm +35 mesh). Consequently various other processes were adapted, including agglomerate tabling and spiral separation of reagentized feed. Today the three processes are used—washing and screening for coarse pebble, tabling or spiraling for intermediate sizes, and flotation for —35 mesh material.

Jan 1, 1959

By O. M. McRae

The Courtland-Gleeson area is in Cochise County about 15 miles east of Tombstone in southeastern Arizona. Rocks exposed in the area range in age from Pre-cambrian to Quaternary. The Precambrian is repre-sented by the Pinal schist. Paleozoic rocks include the Cambrian Bolsa quartzite and Abrigo limestone, Mississippian Escabrosa limestone, and the Permo-Carboniferous Naco Group limestones. Rocks believed to be of Triassic and/or Jurassic age include the Copper Belle monzonite porphyry, Turquoise granite, and Gleeson quartz monzonite. The Cretaceous is represented by andesitic volcanics and various sedimentary rocks. Tertiary rocks include the intrusive and extrusive Sugarloaf quartz latite porphyry and numerous dikes of various rock types. Quaternary conglomerates cover the northern and eastern part of the area. The geologic structure is extremely complex. All rocks as old as early Tertiary have been involved in either tilting, normal faulting, high angle reverse faulting, imbricate thrusting or folding and overfold-ing. Major deformation was initiated during the first half of the Tertiary. Northeast-southwest compres-sional forces caused thrust plates containing lower Paleozoic rocks to override Cretaceous rocks. Subsequently, two large slide blocks of lower Paleozoic rocks, acting under the influence of gravity, moved eastward. The imbricate structure and the gravity slide blocks were then broken by late Tertiary normal faults. INTRODUCTION The Courtland-Gleeson area, or Turquoise Mining District, has long been recognized as an area of extreme structural complexity. Gilluly 2 referred to the entire district as a "gigantic thrust breccia". In 1962, Bear Creek Mining Company completed a two year program of detailed geologic mapping supported by exploration drilling. The purpose of this paper is to present some of the results of this investigation and to provide a structural interpretation based on these results. The geologic map that accompanies this report is generalized and shows only the major and significant features. The area was initially mapped on aerial photographs on a scale of 1 in. equals approximately 500 ft. These data were transferred to a planimetric base using a vertical sketch master. LOCATION The Courtland-Gleeson area is in central Cochise County, about fifteen miles east of Tombstone, and about twenty-two miles northeast of Bisbee in southeastern Arizona (Fig. 1). The area is readily accessible over graded gravel roads from both Tombstone and Elfrida. GENERAL GEOLOGY Rocks exposed in the area range in age from Pre-cambrian to Quaternary. wilson3 and Gilluly2 have published very detailed descriptions of the principal rock units exposed in the area. Only a summary description is provided in Table I. A great number of previously unmapped narrow Tertiary dikes and small irregular masses of hornblende andesite porphyry, lamprophyre, and aplite intrude the Gleeson quartz monzonite in the western part of the map area. The scale of the map prohibits showing them. The aplite dikes are related to, and bear the same structural relationships as, the Sugarloaf quartz latite dikes found in this area. For that reason, and because both the hornblende andesite porphyry and the lamprophyre are post-mineral and post-thrusting, their omission from the map is not considered significant. Because so many of the contacts in the district are fault contacts, because bedding faults appear to be prevalent but are difficult to recognize and map, and because igneous intrusions are so common throughout the sedimentary section, it is virtually impossible to measure an exact total thickness of any of the sedimentary rock units. Nevertheless, neither the field mapping program nor the diamond drilling provided any basis for suspecting that the thicknesses of the sedimentary units are significantly greater or less than what might be inferred from surrounding districts.

Jan 1, 1967

By Phillip E. Deering, Robert M. Cox

A model pillar study was conducted in which the engineering principles of dimensional analysis were applied to the problem of coal mine pillar design. The paper reviews the theory of similitude as applied to the model pillar study conducted in the investigation. An example solution of a design problem is included to indicate how the results of the study may be used as a first approximation in the design of coal mine pillars. The design of mine pillars for adequate support with minimum loss of valuable raw materials has always presented a problem to the mining engineer. Most often, for lack of a better method, past practice has influenced the design of new mine pillars. This process has always left doubt as to the safety factor of the pillars. The work presented in this paper is an initial attempt toward adapting the engineering principles of dimensional analysis to the problem of pillar design in underground mines. The use of the dimensional analysis technique is advantageous because all the variables associated with the problem are considered, and by systematic analysis the relative influence of each variable is determined. The model material utilized in this study was taken from the Helena seam of the Cahaba coal field located in central Alabama. The research study was sponsored by The Southern Electric Generating Co. as part of an over-all rock mechanics investigation of the Helena seam area. THEORY OF SIMILITUDE Model analysis is used extensively in engineering today, particularly in the solution of design problems that defy the classical methods of analysis. Such problems arise when materials with a nonlinear stress-strain relationship are involved, when geo- metric boundaries are difficult to define in simple form, when strains become large, or when partial failure occurs. All of these difficulties usually exist in pillar design problems. Those principles which underlie proper design and construction of models, and the interpretation of test results, comprise the theory of similitude. That is, the theory of similitude includes a consideration of the conditions under which the behavior of two separate entities or systems will be similar, and the techniques of accurately predicting behavior of one from observation of the other. The theory of similitude may be developed by dimensional analysis. Dimensional analysis, as a powerful analytical tool, is developed from a consideration of the dimensions in which each of the important quantities involved in a phenomenon is expressed. It is based on two axioms: 1) Absolute numerical equality of quantities may exist only when the quantities are similar qualitatively. 2) The ratio of the magnitudes of two like quantities are dependent on the units used in their measurement, provided that the same units are used for evaluating each. Dimensional analysis, developed from these two axioms, differs from other types of analysis in that it is based solely on the relationships that must exist among the pertinent variables because of their dimensions, rather than on the relationship of natural laws. In itself, dimensional analysis ~rovides qualitative, rather than quantitative relationships, but when it is combined with experimental procedures, it may be made to supply quantitative results and accurate prediction equations. APPLICATION OF THEORY The design of an adequate mine pillar requires the determination of a design equation and the selection of a dimensional system with which to work. Since force plays an important part in the design of mine support, the FLT (force, length, time) system has been used. The factors involved in the dimensional analysis of mine pillars and their dimensions are: A = cross-sectional area L Cp = design strength FL- E, = tangent modulus of elasticity FL

Jan 1, 1969

Jan 1, 1971

By James Barr

Geology and Mineralogy1 TENNESSEE phosphates are commercially divided into three varieties: Brown, blue and white. The first two only are now of commercial importance. The white phosphates of Perry county are not being mined at present owing to their pockety occurrence. The white phosphate is Fig. I.-DEPOSITS OF 75 PER CENT. BROWN PLATE ROCK UNDERLAIN BY SAND. the highest grade of the three varieties, running often more than 90 per cent. tricalcium phosphate. The brown rock is found in three varieties, grading from the dense almost vitreous gray rock, 76 to 82 per cent. tricalcium phosphate, down

Jan 9, 1914