Search Documents

By H. M. Howe

(New York: Meeting, October, 1913.) 1. INTRODUCTION.-This paper gives the results of our micro-graphic determinations of the position of Ae3 in a series of 14 hypo-eutectoid steels of varying carbon content, one of them very rich in phosphorus, and of SEe for one hyper-eutectoid steel. We have pro-ceeded chiefly by noting the temperature -at which the reabsorption of the pro-eutectoid element is found to be complete after a 30-min. holding, but in part also by noting the temperature at which its precipitation begins. Observations on these same steels by Messrs. Burgess, Crowe, and Rawdon, of the United States Bureau of Standards, are given in a paper' issued simultaneously with this, while in a third paper s one of us compares these data with those of earlier observers. These three papers are treated as one whole by numbering their sections, tables, and illustrations continuously, and by setting the folding plates of micrographs at the end of the last paper. THE COMPOSITION OF THE STEELS EXPERIMENTED ON is given in Table I. Notation. and Definitions.-Following Osmond's development of Tschernoff's notation; in which " Ac3 " is the upper limit of the hypo-eutectoid part of the transformation range as observed in heating up, and " Ar3 " is that same limit as observed in cooling down, and following the usual custom of calling the upper limit of the hyper-eutectoid part of that range "SE," we may go farther and call this latter limit " SEc " when observed in heating up .and " SEr " when observed in cooling down.

Jan 6, 1913

By Hans Lundberg

IN ORDER to comprehend the help and information that may be expected from electrical prospecting, it is necessary to have at least a general knowledge of the methods and principles involved in preparing and interpreting results obtained in the field. Electrical prospecting is rather complicated, both in theory and practice, and in order to make a brief description clear to the practical mining man it has been necessary to idealize and generalize the problems, at the risk of having such simplification criticized by the theoretical man. This simplification must not be misinterpreted as showing a lack of theoretical knowledge. FIG. 1.-FLOW OF CURRENT IN AND AROUND A CONDUCTING BODY. For its operation, electrical prospecting mainly depends on-the fact that most metallic ores conduct an electric current much more readily than barren rocks. If an electric current flows through a block of ground within which a body of chalcopyrite is enclosed in country rock of schist, the current will find less resistance to its passage through the chalcopyrite than through the schist, even though the passage through the latter be much shorter. This is because the longer path through the chalcopyrite offers less resistance, owing to the superior electrical conductivity of the chalcopyrite (Fig. 1).

Jan 1, 1928

By Carl F. Floe, Hung Liang, Michael B. Bever

DATA on the solubility of hydrogen in iron-silicon alloys are of practical interest, as hydrogen causes gas unsoundness and embrittlement in iron and steel and is also a factor in the metallurgy of cast iron. Zapffe and Sims1 have recently demonstrated that in deoxidized iron and steel castings gassiness and bleeding are primarily functions of the hydrogen content of the liquid metal. These authors also suggested convincingly that ordinary melting and casting practice provides several sources of hydrogen for absorption by the metal. Norbury and Morgan,2 and Boyles3 have shown that dissolved hydrogen affects the graphitization of cast iron. Schneble and Chipman4 included in a study of the effects of superheating on the properties of cast iron an investigation of the part played by hydrogen. Schwartz, Guiler and Barnett6 investigated the significance of hydrogen in the metallurgy of malleable cast iron. A complete interpretation of investigations of this kind calls for equilibrium values of the solubility of hydrogen in the liquid and solid phases. From the theoretical standpoint, the solubility of gases, especially hydrogen, may reveal some aspects of the nature of liquid metallic solutions. This was implied in the early work of Sieverts6 on the effect of alloying additions on the solubility of hydrogen in copper. Recent work by Bever and Floe7 has shown that in liquid copper-tin alloys the solubility of hydrogen changes abruptly at the composition of the intermetallic compound Cu3Sn. It is of considerable interest to determine whether liquid alloys of iron also have compositions at which the solubility of hydrogen exhibits a discontinuous or otherwise unique behavior. Among the various alloys of iron the iron-silicon system is important because of the presence of silicon in various structural alloy steels, transformer sheets, cast irons and special acid-resisting castings. The various grades of ferrosilicon, finally, cover almost the entire remainder of the composition range. Published information on the solubility of hydrogen in iron-silicon alloys is meager. The first values for pure liquid - iron were reported in 1910-1911 by Sieverts and Krumbhaar8 and by Sieverts.9 They found that 100 grams of iron absorbs 28 C.C. of hydrogen at 1550°C. and one atmosphere pressure, and 31 C.C. at 1650°C. In 1938 Sieverts, Zapf and Moritz10 published a value of 26.3 c.c. at 1550°C. Data on the solubility of hydrogen in liquid iron-silicon alloys and in liquid silicon

Jan 1, 1946

Granduc lies near the Alaskan border in British Columbia, about 600 miles (960 km) north of Vancouver. Prospecting in the area must take place in the short summer months of fog and rain because the winter is bitter cold, with snowfall up to 960 inches (24.4 m) accompanied by avalanches. Despite these difficulties, the mineral ized area was discovered in the 1920's. By 1956, Newmont Mining Corporation had developed mineable ore reserves estimated at 32,500,000 tons of 1.93% copper. Newmont and ASARCO, in a joint venture, then began development of the ore body, which was partially covered by glaciers. It was apparent a concentrator could not be built at the mine site where overland access was impossible due to the weather conditions and the terrain. Years of engineering studies of all possible access routes finally dictated the driving of an 11 mi long (17.6 km) tunnel passing under three glaciers and three mountain ranges to the nearest feasible concentrator site at Tide Lake. Even then, a mountain road subject to an average snowfall of 800 in. (20. 3 m) had to be built 32 mi (51 krn) from the concentrator through Alaska to Stewart, British Columbia, the nearest port. At Stewart, which is located at the head of a fjord 120 mi (192 krn) from the Pacific Odean, a fully equipped marine terminal was built. The tunnel, the lifeline between mine and mill, was to be driven from both ends; however, in 1965, an avalanche occurred at the Leduc portal, killing 26 crew members and wrecking much of the camp. The tunnel was then driven from one heading adjacent to the concentrator site at Tide Lake, a distance of 53,744 ft (16,381 m) to a point under the ore body. The remote location, type of terrain, and bad weather made supply of crews, equipment, and construction materials difficult; but in spite of these extremely adverse conditions, the tunnel crews set many world records. Mineralization throughout the ore zone is generally uniform in grade and composition and is primarily chalcopyrite and pyrrhotite associated with pyrite. Mining is mainly by sublevel caving. After blasting, rubber-tired load-and-haul equipment moves from level to level by means of an internal connecting ramp system on a 15% slope. At the gathering haulage level, 15-ton bottom-dump cars deliver the ore to a 600-ton pocket equipped with a Hudson "Rock-Flo" dump. The bottom of the ore pocket forms the feed chute to the primary

Jan 1, 1978

By M. E. Hassan, J. C. Calhoun, R. F. Nielson

An apparatus was constructed for the measurement of inter-facial tensions over a range of temperatures and pressures. This apparatus utilized the pendent drop method, and resembles in construction similar apparatus recently described in the literature and in use in some petroleum research laboratories. The interfacial tensions of benzene, propane, n-pentane, n-hexane. n-octane. and iso-octane against water were measured at temperatures ranging from 26" to 82" C and at pressures ranging from 1 to 204 atm. Values of interfacial tensions for the henzene-water system and their variations with temperature and pressure are generally in good agreement with value? of previous investigations. The data in all cases showed a slight decrease of interfacial tension with pressure at constant temperature in the range studied. The effect of pressure became less as the pressure was increased, with an indication of a reversal of the effect at higher pressures. There was a decrease of interfacial tension with temperature at constant pressure in all cases, as would normally be expected. This rate of decrease became greater the higher the temperature. A general equation is presented for the interfacial tensions as a function of presPurp and temperature over the range studied, and the constants calculated for each system. A definite trend was found in the effect of molecular weight on the interfacial tension at a given temperature and pressure, for the homologous series from propane to n-octane. Data for n-decane from the literature fitted well into this trend. INTRODUCTION It has been recognized for many years that surface forces play an active part in the production history of an oil reservoir as well as in determining the amount of unrecoverable oil. The magnitudes of these forces are governed by the values of the interfacial tensions. These vary greatly with composition, pressure, and temperature. The effect of composition is greater than that of pressure and temperature over the ranges normally encountered. In fact, because of the variety of compounds present in a crude, no attempt has yet been made to correlate crude composition with its surface tension or with its interfacial tension against water. The amount of dissolved methane greatly affects the surface properties of an oil, and there are "surface-active" compounds in crudes which have a much greater effect on boundary tensions than do equal amounts of hydrocarbons. The purpose of the present work was partly to contribute data that would eventually be used in correlations applicable

Jan 1, 1953

By H. J. Rose

Sixty-five million net tons of coal were carbonized in the by-product and beehive coke ovens1 of the United States during 1924. This tonnage represented 13.4 per cent. of the bituminous coal which was mined in that year. Table 1 shows production and disposition.2 Table 1.—Production and Disposition of Ocen Coke in 1924 By-product Beehive Total Coal charged into ovens, tons................ 49,061,339 15,914,310 64,975,649 Coke produced (exclusive of screenings and breeze), tons............................. 33,983,568 10,286,037 44,269,605 Average yield of coke, per cent ............. 69.3 6.46 68.9 Disposition of coke, per cent.: Blast furnace.......................... . . 82.6 Foundry............................... . 13.3 6.6 Domestic.............................. . 1.4 6.7 Water gas manufacture and all other uses.. 4.6 . 4.1 Cokes having somewhat different combinations of chemical and physical properties are desired for the various uses listed above, and these properties depend primarily upon the types of coal used. American coals have a wide range of purity and coking quality, and the chief subject of this paper will be the selection of coals for the manufacture of blast furnace, foundry, domestic, and water-gas coke, in by-product coke ovens. It will obviously be necessary to include a discussion of those physical and chemical characteristics that are generally considered essential or desirable for each type of coke. Suitable Coals The examination and development of new sources of coking coal are important because of the irregular and limited distribution of high-grade

Jan 1, 1927

ALBERT Ladd Colby, who died suddenly of influenza at Torquay, England, on Apr. 30,1924, was born in New York City, on June 26,1860. He was educated in the public schools of New York, at the College of the City of New York, and received the degree of Ph. B. from the Columbia School of Mines in 1881. He continued his studies at Columbia, acting occasionally as assistant to Prof. C. F. Chandler, until 1883. For the next three years he was Assistant Professor of Chemistry in Lehigh University; then head chemist and metallurgical engineer of the Bethlehem Steel Co., at Bethlehem, Pa., occupying the latter position until 1903. As head chemist his active and inventive mind devised several improvements in apparatus for increasing the rapidity and accuracy of the analytical work; as metallurgical engineer, he was, from time to time, in charge of the blast-furnace, open-hearth, bessemer, and puddling departments; he had entire charge of the inspection, assignment, and economic use of all metallurgical materials, and he early gave his attention to the formulation of specifications for metallurgical materials—an activity in which he long held a distinguished part in this country, and as a representative of his own country in England and Europe. He also sewed as expert for his company in patent suits, again laying the foundation for valuable service later as a consulting engineer. In this latter capacity he was excelled by few, if any, contemporaries in the iron and steel industry. His mind was ingenious, thorough, clear, and keen, both in the preparation of evidence and its presentation to the Court. He very quickly appraised the value of evidence, or of an answer to a question, and knew how to secure the infermation, either from the available literature of any language, or by special researches or plant studies. In the executive control of literary research for patent purposes, his long training, infinite capacity for digging through long series of articles in English, German or French, and clear formulation of the vital subject matter for the guidance of assistants, made him invaluable. He was also an adept in collecting information on special branches of his profession. For example, when the science of metallography began to assume importance, he made the first really comprehensive bibliography covering the literature of all siderurgical countries; for the newly formed International Nickel Co. he gathered all the information extant on the subject of nickel steel, both in the literature and in the minds of experts in America and Europe. Two books testify to the thoroughness of his work in this capacity, vie.: "American Standard Specifications for Steel,"

Jan 1, 1924

By H. M. Howe, Levy A. G.

Four aspects of flow in the plastic deformation of steel by overstrain, such as punching, wire-drawing, tensile rupture, etc, are…

Jan 1, 1915

By E. C. Harder

AT a Meeting of the New York Section, on May 23, 1918, the sole subject of discussion was the nature and occurrence of iron ores in certain parts of the world.? Owing to the importance of this subject, it has been deemed' advisable to publish the remarks made at that meeting in the form of a paper, for presentation at the Milwaukee Meeting, instead of in the usual place, under News of Local Sections. The remarks related to the following districts: Brazil, by E. C. Harder, of the U. S. Geological Survey; Scandinavia, by Waldemar Lindgren, of the U. S. Geological Survey; Cuba, by C. M. Weld, of the U. S. Bureau 'of Mines; Southern Europe, by A. C. Spencer, of the U. S. Geological Survey; China, by H. Foster Bain, of the U. S. Bureau of Mines; Alsace-Lorraine, by Sidney Paige, of the U. S. Geological Survey. BRAZIL By E. C. Harder During the years immediately preceding the war, the iron ores of Brazil were attracting the attention of iron operators both in Europe and in the United States. This was clue to the large quantities of practically undeveloped ore available, and to its great purity. It is reasonably safe to state that had capital not been diverted from the exploitation of these deposits to war purposes, Brazilian iron ores would probably now be offered in European and American markets. It is certain that after the war these ores will play a prominent part in the economic reconstruction of Europe and perhaps in the development of America.

Jan 9, 1918

By T. L. McCall

THE late Walter Herd1 in 1929 gave a full description of past and present conditions in No. 2 mine, Springhill, Nova Scotia, developed theories regarding the cause of these bumps and made certain suggestions regarding possible methods of future development. Recapitulating briefly from Mr. Herd's paper, the seam is bituminous coal, averages 9 ft. in thickness and has a well defined parting containing fusain about 14 in. from the roof. This roof coal is somewhat stronger than the rest of the seam and has a tendency to cling to the roof. The pitch of the seam where it is now being worked is about 20°. The first manifestations of bumps began when the room and pillar workings had reached a depth of cover of 1900 ft. and under continuously increasing depth of cover these bumps increased to such an extent, both in number and severity, that in the year 1924 it became apparent that some change in the system of extraction was necessary. After closely studying all the factors involved and benefiting largely by valuable out-side advice obtained by the Provincial Department of Mines of Nova Scotia,2 the system of working was changed from room and pillar to longwall retreating. Mr. Herd's paper described in detail three remarkable bumps in the year 1928 in April, July and October that affected the 5700-ft. and 5900-ft. East levels, the last bump being so severe both in intensity and in extent of damage done that this district was abandoned. The longwall workings to the west of the slope had been stopped in the year 1926 owing to an inbreak of water, coming from the flooded waste of No. 3 seam lying some 400 ft. vertically overhead. This inflow was not excessive, but a large quantity of water being impounded in the old workings it was considered advisable to take the prudent course and not incur the risk of possibly increasing the flow by further working. This district has remained idle ever since.

Jan 1, 1934

By D. B. Rushmore, K. A. Pauly

Of primary importance in mine-installations is the hoist, which has a very direct bearing on the successful operation of a mine. Conditions vary greatly with different mines, and especially in different localities. Such factors as depth, incline, the number of levels, permissible or desirable speeds, conditions of ore, etc., are always more or less special in each case. Veins of ore are never exactly duplicated, and the nature of the ground through which shafts are sunk may considerably modify permissible values. As mining-laws are made by the different States, they necessarily vary somewhat, and, even when not fully observed, they introduce factors which qualify the conditions of hoisting men and ore. The amount of timbering required is often of importance as relating to hoisting-conditions. Methods of loading ore affect the time required, as also does the question of the use of cars or skips. Safety-precautions must be very carefully considered, and the number of men in each mine, the number of compartments, and often the method of removing water from the mine, must have careful consideration. While a general discussion of the subject of hoisting is possible, most cases are entirely special, and can be considered only in connection with the peculiar conditions pertaining to that particular installation. The cost of installation of the hoisting-plant may be an appreciable amount, while the cost of raising the ore may be but a small part of the total operating-charge. In many cases, however, the output of the mine is limited by the capacity or the hoist, and the latter thus becomes of the first importance.

Jan 1, 1911

By R. E. Zimmerman

Wide attention is being placed upon various methods for cleaning the fine sizes of bituminous coals. The author describes and analyzes the results achieved on wet concentrating .tables of modern design on unclassified feeds of - 1/2 in. particle sizes, including tests on high-sulphur coals.

Jan 1, 1950

Sailing westward from the Society Islands in the fall of 1774, England's noted explorer Captain James Cook discovered New Caledonia-that long, linear island that has played such an important and varied role in the history of nickel. Upon his return to England the following year, Cook's announcement of this uncharted island generated governmental interest, but its distance from the Island Empire, the troubles in the colonies, and the difficulties with France combined to keep English interest indirect and in the background of the then-current events.

Jan 10, 1968

By D. H. Newland

New York has a small but not insignificant place in the oil and natural gas industries of the United States. It has had a continuous record as an oil producer since 1872, with an aggregate yield of about 104,000,000 bbl. The reported output for 1935 was 4,237,000 bbl., a gain of more than 10 per cent for the year and a total that has been exceeded only in the early period of flush production half a century ago. The industry has been steadily building up since 1920 with the successful practice of the water drive, which has given a new lease of life to pools that had been practically drained of oil recoverable by pumping. An additional output of 2000 bbl. or more per acre is being procured by this method. Altogether the fields in New York State cover about 55,000 acres. Their limits are well defined and it is unlikely that they will be extended in the future, although there is some prospect of finding additional supplies by deeper drilling. The oil from New York is all classed as Pennsylvania grade, for which the recent price has been about $2.50 a barrel. It is refined at Olean, Wellsville and Bolivar, in the oil district, and partly in Pennsylvania refineries. Exploration for natural gas, outside of the established districts, was considerable during the year. Altogether 59 wells were drilled, distributed over 13 counties, of which 33 were listed as producers and 26 were dry. At the close of the year, 13 wells were in process of drilling. The 33 producing wells had a combined estimated flow of 278 million cubic feet per day. The best results were obtained from exploration in Allegany County, where out of eight wells drilled to the Oriskany sandstone five were successful and showed a combined open-flow capacity of 107 million cubic feet. The Oriskany sandstone was encountered at a depth of 4500 to 4900 ft. In Steuben County, next east of Allegany County, two out of seven wells to the Oriskany proved productive, and one of these, in the town of Greenwood, on the Watkins structure, was probably the largest that has so far been opened in the state, with a reported yield of 35 million a day. In the central part of New York interest was awakened by the activity shown in exploring for gas in the Trenton limestone, in Camden, Florence and Rome townships, Oneida

Jan 1, 1936

By D. H. Newland

New York has a small but not insignificant place in the oil and natural gas industries of the United States. It has had a continuous record as an oil producer since 1872, with an aggregate yield of about 104,000,000 bbl. The reported output for 1935 was 4,237,000 bbl., a gain of more than 10 per cent for the year and a total that has been exceeded only in the early period of flush production half a century ago. The industry has been steadily building up since 1920 with the successful practice of the water drive, which has given a new lease of life to pools that had been practically drained of oil recoverable by pumping. An additional output of 2000 bbl. or more per acre is being procured by this method. Altogether the fields in New York State cover about 55,000 acres. Their limits are well defined and it is unlikely that they will be extended in the future, although there is some prospect of finding additional supplies by deeper drilling. The oil from New York is all classed as Pennsylvania grade, for which the recent price has been about $2.50 a barrel. It is refined at Olean, Wellsville and Bolivar, in the oil district, and partly in Pennsylvania refineries. Exploration for natural gas, outside of the established districts, was considerable during the year. Altogether 59 wells were drilled, distributed over 13 counties, of which 33 were listed as producers and 26 were dry. At the close of the year, 13 wells were in process of drilling. The 33 producing wells had a combined estimated flow of 278 million cubic feet per day. The best results were obtained from exploration in Allegany County, where out of eight wells drilled to the Oriskany sandstone five were successful and showed a combined open-flow capacity of 107 million cubic feet. The Oriskany sandstone was encountered at a depth of 4500 to 4900 ft. In Steuben County, next east of Allegany County, two out of seven wells to the Oriskany proved productive, and one of these, in the town of Greenwood, on the Watkins structure, was probably the largest that has so far been opened in the state, with a reported yield of 35 million a day. In the central part of New York interest was awakened by the activity shown in exploring for gas in the Trenton limestone, in Camden, Florence and Rome townships, Oneida

Jan 1, 1936

By B. B. Zavoico

During 1936 the Russian oil industry made very satisfactory progress and, while not all difficulties of organization have been ironed out, the country is now assured of a supply of petroleum products in sufficient quantities and of quality demanded by modern motor equipment. The year 1937 promises to better by a wide margin the good showing of 1936. The statistics given in this paper for the first time take into consideration the varying gravities of crude oils of the several Russian oil fields instead of using a flat conversion factor of 7 bbl. per metric ton. It was found from the detailed study that the generally used average conversion factor should be increased from 7 to 7.25 bbl. per metric ton, the figure varying, of course, with the gravity of oil in the individual fields. Crude-oil production during 1936 is estimated at 201,500,000 bbl. as compared with 182,970,000 bbl. produced in 1935, an increase of 9.4 per cent. The greatest increase was again recorded in the Baku district, which increased its production by 10.9 per cent, from 141,257,000 bbl. in 1935 to 158,300,000 in 1936. Grozny district maintained its production at a level of about 23,000,000 bbl., but its old fields continued to decline and production was sustained by the development of newer fields. A great advance was made in drilling speeds and the total footage in 1936 reached 6,694,200 ft. as compared with 4,926,600 ft. drilled in 1935, an increase of 26.4 per cent. In older deep fields, producers were being completed at over 8000 ft.—a great depth for Russian drillers but two years ago. Several major discoveries were made in 1936. Northeast Caucasus.—Izberbash, east from Grozny and on the Caspian Sea, was the outstanding discovery, the initial production of the discovery well being around 3000 bbl. per day from about 5000 ft. The importance of the field is due to the large area of the structure, half of which, however, is under the sea, and also to its strategic location on the shores of the Caspian and near a trunk pipe line to the Grozny refining center. An active development program is being pursued in Izberbash and its 1937 production quota is set at 7,500,000 bbl. Achi-Su field, near Izberbash, also discovered during 1936, while not as prolific as Izberbash, is thought to cover a very large area and the small

Jan 1, 1937

Separates of all the Technical Publications published in 1931 are available at Institute headquarters. All the papers are on file in public, university and technical libraries, and when so indicated in the list, may be found in the Transactions. Copies of these papers have been mailed to those members of the Institute who are registered in the different classes: A-Metal Mining; B-Milling and Concentration; C-Iron and Steel Division; D-Nonferrous Metallurgy; E-Institute of Metals Division; F-Coal Division; G-Petroleum Division; H-Nonmetallic Minerals; I-Mining Geology; K-Mining Administration; L-Geophysical Prospecting. Other members may obtain copies by writing to the Secretary. Additional copies are sold at the rate of I cent per page; minimum charge, 25 cents. Metal Mining Tech-nical Publi- Title Author Meeting TRanb. cation Volume No. and Page* 411-A.43 Ventilation at the Portovelo Mines, J. P. Harmon New York. T31, 83 Ecuador (18) Feb., 1931 425-A.44 Use of Models for the Study of Mining P. B. Bucky New York, Problems (28) Feb., 1931 Milling and Concentration 375-B.32 Ball Mill Studies, I (53) A. W. Fahrenwald New York, H. E. Lee Feb.. 1931 401-B.33 Experimental Flotation of Oxidized H. S. Gieser New York. Silver Ores (9) Feb., 1931 410-B.34 Flotation of Minor Gold in Large-scale E. S. Leaver New York, Copper Concentrators (32) J. A. Woolf Feb., 1931 414-B.35 Effect of Particle Size on Flotation A. M. Gaudin New York, (23) J. 0. Groh Feb., 1931 H. B. Henderson 416-B.36 Ball Mill Studies, 11.—Thermal A. W. Fahrenwald New York. Determinations of Ball Mill Effi- G. W. Hammar Feb., 1931 ciency (13) H. E. Lee W. W. Staley Iron and Steel Division 38QC.59 Open-hearth Steel Process as a Prob- E. R. Jette New York, C31, 80, 111 Iem in Chemical Kinetics (34) Feb., 1931 381-C.60 Thermodynamic Study of the Phasial Yap, Chu-Phay New York. Equi1ibriain the System Iron-car- Feb., 1931 bon (26) 382-(3.61 Influence of Dissolved Carbide on the Yap, Chu-Phay New York, Equilibria of the System Iron-car- Feb., 1931 ban (19) 383-C.62 Research on Blast-furnace Slags. R. S. McCaffery New York, Three papers (88) Co-workers Feb., 1931 384-C.63 Statistical Analysis of Blast-furnace K. S. McCaffery New York, C31, 60, 70 Data (13) R. G. Stephenson Feb., 1931

Jan 1, 1931

By J. M. Sands

Production of oil in Oklahoma during 1927 amounted to 273,256,900 bbl. (Table l), an increase of nearly 100,000,000 bbl. over the previous year. All of the major fields declined with the exception of those of the Seminole district which produced 136,105,000 bbl., almost one-half of the total production of the state. Because of this large new production, most of the development in the state during the year took place in that district. The Seminole City pool located in T.-9-N., R.-6-E., was the first of these pools to be developed. The Indian Territory Illuminating Oil Co. brought in the first well in this field in March, 1926, for 1100 bbl. This well is located in Sec. 24-T.-9-N., R-6-E., and produced from the Hunton lime reached at depth of 3900 ft. The first Wilcox production was developed by the Independent Oil & Gas Co. and R. S. Garland in Sec. 26, T.-9-N, R-6-E. This well was being drilled for production in the Hunton lime but was dry in this horizon and was deepened to the Wilcox sand in July, 1926, and at the total depth of 4069 ft. developed a maximum production of 8000 bbl. daily. It held up in wonderful manner and was the cause of not only the development of this pool but the prospecting of the whole district for the Wilcox sand. This led to the discovery of the other major pools in that district. Seminole City pool reached a peak production of 264,500 bbl. on February 22, 1927, and slowly declined so that by December it had a daily average of 56,200 bbl. from 321 wells. The second pool in this district to be discovered was the Searight pool which was discovered by F. J. Searight et al. in Sec. 33, T-10, R-6, in April, 1926. The first well was drilled to the Hunton lime encountered at 4115 ft., and came in for 1300 bbl. daily. During August, 1926, the second well was drilled on the same farm through the Hunton lime to the Wilcox sand which was encountered at 4360 ft. It came in for an initial production of 4000 bbl. daily. This started active drilling in this field for the Wilcox sand. The field had a peak production of 40,621 bbl. on June 15, 1927, and declined to a daily average of 22,300 bbl. from 73 wells during December.

Jan 1, 1928

By John R. Anderson, Michael B. Bever

CARBON may affect the alloys of copper in several ways. Provided an alloying element does not oxidize preferentially, even minute quantities of carbon dissolved in liquid alloys of high copper content will form insoluble carbon oxide gases under oxidizing conditions. Gas porosity in castings of high-copper alloys can originate in this way. In certain alloys of low copper content carbon may have considerable solubility and may be an effective deoxidizer. In these alloys carbon will tend to suppress porosity. Carbon that is dissolved in the molten alloy is likely to be retained in the solidified metal. The effects of carbon on the physical properties of the metal are determined by the form in which it is present. Depending on the alloying elements and also on the cooling rate, carbon may precipitate as graphite, may form a carbide or may remain in solid solution on cooling. As solid copper does not dissolve a measurable amount of carbon, a carbon-bearing solid solution can occur only if the copper is alloyed with a large excess of an element that forms such a solution. The effect of graphite or of carbides on the properties of an alloy will depend on the size and distribution of the precipitated particles. As Hensel pointed out in discussion,1 the formation of an alloy carbide may interfere with the age-hardening properties of a copper alloy. One would also expect that the presence of carbides or of graphite will under certain conditions promote corrosion or high-temperature failure in nonferrous alloys. Since carbon has an effect on the soundness of castings and affects the structure and behavior of solid copper alloys, its solubility in the liquid alloys is of practical importance. The isothermal change of carbon solubility with alloy composition is of interest from a theoretical standpoint. The binary alloys of copper with manganese and with nickel are used industrially and serve as a base for more complex alloys. The solubility of carbon in each of these metals is known, but its solubility in their alloys has not been determined. EARLIER DATA The solubility of carbon in molten pure copper is about 0.0001 pct at 1100 °C and 0.0004 pct at 1475°C.1 Various authors2-6 have published data on the solubility of carbon in molten manganese. There is agreement on a value of about 6.7 pct in the temperature range 1217° to 1245°C. This solubility value corresponds to the formula Mn3C. It increases very little with increasing temperature. Corson7 states that carbon is soluble in copper-manganese alloys and that the

Jan 1, 1947

By Michael B. Bever, John R. Anderson

Carbon may affect the alloys of copper in several ways. Provided an alloying element does not oxidize preferentially, even minute quantities of carbon dissolved in liquid alloys of high copper content will form insoluble carbon oxide gases under oxidizing conditions. Gas porosity in castings of high-copper alloys can originate in this way. In certain alloys of low copper content carbon may have considerable solubility and may be an effective deoxidizer. In these alloys carbon will tend to suppress porosity. Carbon that is dissolved in the molten alloy is likely to be retained in the solidified metal. The effects of carbon on the physical properties of the metal are determined by the form in which it is present. Depending on the alloying elements and also on the cooling rate, carbon may precipitate as graphite, may form a carbide or may remain in solid solution on cooling. As solid copper does not dissolve a measurable amount of carbon, a carbon-bearing solid solution can occur only if the copper is alloyed with a large excess of an element that forms such a solution. The effect of graphite or of carbides on the properties of an alloy will depend on the size and distribution of the precipitated particles. As Hensel pointed out in discussion,' the formation of an alloy carbide may interfere with the age-hardening properties of a copper alloy. One would also expect that the presence of carbides or of graphite will under certain conditions promote corrosion or high-temperature failure in nonferrous alloys. Since carbon has an effect on the soundness of castings and affects the structure and behavior of solid copper alloys, its solubility in the liquid alloys is of practical importance. The isothermal change of carbon solubility with alloy composition is of interest from a theoretical standpoint. The binary alloys of copper with manganese and with nickel are used industrially and serve as a base for more complex alloys. The solubility of carbon in each of these metals is known, but its solubility in their alloys has not been determined. Earlier Data The solubility of carbon in molten pure copper is about o.oooi pct at II00°C and 0.0004 pct at 1475°C.l Various authors2""6 have published data on the solubility of carbon in molten manganese. There is agreement on a value of about 6.7 pct in the temperature range r2170 to 1245°c This solubility value corresponds to the formula Mn3C. It increases very little with increasing temperature. Corson7 states that carbon is soluble in copper-manganese alloys and that the

Jan 1, 1947